Professional Documents
Culture Documents
DSC1610015CE
B26
TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3 8.5. Service Position (Flange Back Adjustment) ------ 42
1.1. General Guidelines ----------------------------------------3 9 Disassembly and Assembly Instructions -------------- 43
1.2. Leakage Current Cold Check ---------------------------3 9.1. Camera Body Part--------------------------------------- 43
1.3. Leakage Current Hot Check (See Figure. 1)--------3 9.2. Disassembly and Assembly Procedure for the
1.4. How to Discharge the E.Capacitor on Flash Lens --------------------------------------------------------- 58
P.C.B.----------------------------------------------------------4 10 Measurements and Adjustments -------------------------- 59
2 Warning --------------------------------------------------------------5 10.1. Matrix Chart for Replaced Part and Necessary
2.1. Prevention of Electrostatic Discharge (ESD) Adjustment ------------------------------------------------ 59
to Electrostatically Sensitive (ES) Devices ----------5 11 Maintenance------------------------------------------------------ 62
2.2. How to Recycle the Lithium Ion Battery (U.S. 11.1. Notice in External Cleaning --------------------------- 62
Only)-----------------------------------------------------------5 12 Block Diagram --------------------------------------------------- 63
2.3. How to Replace the Lithium Battery -------------------6 12.1. Overall Block Diagram---------------------------------- 63
2.4. Caution for AC Cord (For EB/GC/GH) ----------------7 12.2. System Control Block Diagram ---------------------- 64
3 Service Navigation------------------------------------------------8 12.3. Video/Audio Process (1) Block Diagram----------- 65
3.1. Introduction --------------------------------------------------8 12.4. Video/Audio Process (2) Block Diagram----------- 66
3.2. About service of bundled lenses -----------------------8 12.5. Video/Audio Process (3) Block Diagram----------- 67
3.3. Important Notice --------------------------------------------8 12.6. Gyro Block Diagram------------------------------------- 68
3.4. Service Notes --------------------------------------------- 13 12.7. Flash/Hot Shoe Block Diagram ---------------------- 69
3.5. General Description About Lead Free Solder 12.8. Lens Block Diagram------------------------------------- 70
(PbF) -------------------------------------------------------- 15 12.9. Power(1) Block Diagram ------------------------------- 71
3.6. How to Define the Model Suffix (NTSC or PAL 12.10. Power(2) Block Diagram ------------------------------- 72
Model)------------------------------------------------------- 16 12.11. Power(3) Block Diagram ------------------------------- 73
4 Specifications ---------------------------------------------------- 21 13 Wiring Connection Diagram -------------------------------- 74
4.1. Camera Body---------------------------------------------- 21 13.1. Interconnection Diagram------------------------------- 74
4.2. Lens --------------------------------------------------------- 26 14 Schematic Diagram -------------------------------------------- 75
5 Location of Controls and Components------------------ 28 15 Printed Circuit Board------------------------------------------ 75
5.1. Camera Body---------------------------------------------- 28 16 Exploded View and Replacement Parts List----------- 75
5.2. Lens --------------------------------------------------------- 30
6 Service Mode ----------------------------------------------------- 31
6.1. Error Code Memory Function ------------------------- 31
7 Troubleshooting Guide---------------------------------------- 33
7.1. Checking Method of Body and
Interchangeable Lens ----------------------------------- 33
7.2. Wi-Fi Circuit (Jack P.C.B.) ----------------------------- 37
8 Service Fixture & Tools --------------------------------------- 38
8.1. Service Fixture and Tools ------------------------------ 38
8.2. Clean Box -------------------------------------------------- 40
8.3. When Replacing the Main P.C.B. -------------------- 40
8.4. Service Position (When checking the each
P.C.B.)------------------------------------------------------- 41
2
1 Safety Precautions
1.1. General Guidelines 1.3. Leakage Current Hot Check
1. IMPORTANT SAFETY NOTICE (See Figure. 1)
There are special components used in this equipment
1. Plug the AC cord directly into the AC outlet. Do not use
which are important for safety. These parts are marked by
an isolation transformer for this check.
2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F
in the Schematic Diagrams, Circuit Board Layout,
capacitor, between each exposed metallic part on the set
Exploded Views and Replacement Parts List. It is essen-
and a good earth ground, as shown in Figure. 1.
tial that these critical parts should be replaced with manu-
3. Use an AC voltmeter, with 1 k/V or more sensitivity, to
facturer’s specified parts to prevent X-RADIATION,
measure the potential across the resistor.
shock, fire, or other hazards. Do not modify the original
4. Check each exposed metallic part, and measure the volt-
design without permission of manufacturer.
age at each point.
2. An Isolation Transformer should always be used during
5. Reverse the AC plug in the AC outlet and repeat each of
the servicing of AC Adaptor whose chassis is not isolated
the above measurements.
from the AC power line. Use a transformer of adequate
6. The potential at any point should not exceed 0.75 V RMS.
power rating as this protects the technician from acci-
A leakage current tester (Simpson Model 229 or equiva-
dents resulting in personal injury from electrical shocks. It
lent) may be used to make the hot checks, leakage cur-
will also protect AC Adaptor from being damaged by acci-
rent must not exceed 1/2 mA. In case a measurement is
dental shorting that may occur during servicing.
outside of the limits specified, there is a possibility of a
3. When servicing, observe the original lead dress. If a short
shock hazard, and the equipment should be repaired and
circuit is found, replace all parts which have been over-
rechecked before it is returned to the customer.
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
3
1.4. How to Discharge the E.Capacitor on Flash P.C.B.
• This unit equipped with two pieces of capacitors as E.Capacitor.
“Either one of the E.Capacitors discharging operation” makes discharging for others as well.
CAUTION:
• Be sure to discharge the E.Capacitors on Flash P.C.B. before disassembling.
• Be careful of the high voltage circuit on Flash P.C.B. when servicing.
[Discharging Procedure]
1. Remove the Capacitor Cover.
2. Put the insulation tube on the lead part of resistor (ERG5SJ102: 1kΩ / 5W).
(An equivalent type of resistor may be used.)
3. Put the resistor between both terminals of E.Capacitor on the Flash P.C.B. for approx. 5 seconds.
4. After discharging, confirm that the E.Capacitor voltage is lower than 10V by using a voltmeter.
4
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as “antistatic (ESD protected)” can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).
5
2.3. How to Replace the Lithium Battery
2.3.1. Replacement Procedure
1. Remove the FLASH P.C.B.. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. “B8501” at component side of FLASH
P.C.B.) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Lithium battery includes electric lead terminals.
NOTE:
This Lithium battery is a critical component.
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-G8/G80/G81/G85/G8M/G80M/G81M/G85M/G80H/G81H/
G85H/G85K series, as well.
6
2.4. Caution for AC Cord 2.4.2.1. Important
The wires in this mains lead are coloured in accordance with
(For EB/GC/GH) the following code:
2.4.1. Information for Your Safety
IMPORTANT Blue Neutral
Your attention is drawn to the fact that recording of pre- Brown Live
recorded tapes or discs or other published or broadcast
As the colours of the wires in the mains lead of this appliance
material may infringe copyright laws.
may not correspond with the coloured markings identifying the
WARNING
To reduce the risk of fire or shock hazard, do not expose terminals in your plug, proceed as follows:
this equipment to rain or moisture.
CAUTION The wire which is coloured BLUE must be connected to the ter-
To reduce the risk of fire or shock hazard and annoying minal in the plug which is marked with the letter N or coloured
interference, use the recommended accessories only. BLACK.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER The wire which is coloured BROWN must be connected to the
To prevent electric shock, do not remove the cover. No user terminal in the plug which is marked with the letter L or coloured
serviceable parts inside. Refer servicing to qualified service RED.
personnel.
Under no circumstances should either of these wires be con-
2.4.2. Caution for AC Mains Lead nected to the earth terminal of the three pin plug, marked with
For your safety, please read the following text carefully. the letter E or the Earth Symbol.
7
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnel’s to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
When turning the image sensor unit mounting screw even a little or removing, the “simplicity flange back adjustment” is need.
Perform the “simplicity flange back adjustment” according to contents described in “10 Measurements and Adjustments” section of
this service manual.
8
3.3.1.3. About Main P.C.B. (Ref.1) & Flash-ROM (IC6003)
Before exchanging the “Main P.C.B.”, confirm that the symptom and/or phenomenon is not due to the setting of functions.
Important:
When cannot be repaired in the IC exchange, and in the case of performing the “Main P.C.B.” exchange,
carry out any of following.
In the case of exchanging the Flash-ROM (IC6003) is same way too.
1. When the camera power can be ON, and camera body and adjustment software can be communicated:
Before replacing the “Main P.C.B. and/or Flash-ROM”, proceed the EEPROM data backup from the unit.
After replacing the Main P.C.B. and/or Flash-ROM, overwrite the EEPROM data with backup data from the unit first,
then proceed the adjustment /inspection. (Almost adjustment/inspection items can be omitted.)
Refer to the adjustment instruction in the adjustment software for details.
2. When the camera power cannot be ON, or camera body and adjustment software cannot be communicated:
Almost full adjustment/inspection must be performed after replacing the “Main P.C.B. and/or Flash-ROM”.
Refer to the adjustment instruction in the adjustment software for details.
Notes after replacement:
Make sure the camera body firmware is latest version.
9
3.3.2. Lens Unit (Interchangeable Lens: H-FS12060)
3.3.2.1. About Lens Main Unit (Ref. 206)
1. Lens Main Unit (Ref. 206) is not supplied due to difficulty of the transportation issue (Fragile, Dust-free packing), and requires
critical lens adjustments.
Therefore, any needs of the “Lens Main Unit” (Ref. 206), carefully confirm its performance in advance.
2. Once “Lens Main Unit” (Ref. 206) is confirmed as defective, place order “Lens Unit” (Ref. 200) and replace Shading Frame
(Ref. 216), to maintain Serial number of owner’s original lens.
10
3.3.3. Lens Unit (Interchangeable Lens: H-FS14140)
3.3.3.1. About Lens Main Unit (Ref. 309)
1. Lens Main Unit (Ref. 309) is not supplied due to difficulty of the transportation issue (Fragile, Dust-free packing), and requires
critical lens adjustments.
Therefore, any needs of the “Lens Main Unit” (Ref. 309), carefully confirm its performance in advance.
2. Once “Lens Main Unit” (Ref. 309) is confirmed as defective, place order “Lens Unit” (Ref. 300) and replace Shading Frame
(Ref. 302), to maintain Serial number of owner’s original lens.
11
3.3.4. Lens Unit (Interchangeable Lens: H-FS1442A)
3.3.4.1. About Lens Main Unit (Ref. 408)
1. Lens Main Unit (Ref. 408) is not supplied due to difficulty of the transportation issue (Fragile, Dust-free packing), and requires
critical lens adjustments.
Therefore, any needs of the “Lens Main Unit” (Ref. 408), carefully confirm its performance in advance.
2. Once “Lens Main Unit” (Ref. 408) is confirmed as defective, place order “Lens Unit” (Ref. 400) and replace Shading Frame
(Ref. 402), to maintain Serial number of owner's original lens.
12
3.4. Service Notes
3.4.1. About Wi-Fi Function
The page number in this chapter does not show the page number of this service manual.
13
3.4.2. Important Notice of Servicing
This camera unit has the personal information of wireless LAN connection the customer has registered.
For the protection of private information, please erase the personal information after the completion of repair by “Initial Settings”.
In addition, please print out the following documents, and pass to the customer with the camera unit.
1. If the settings were reset you will need to reenter your Lumix Club login ID and password.
If you have forgotten the login ID and/or Password, please connect to the Lumix Club web
site and create a new ones.
2.You may also have to reenter the settings for your local Wi-Fi network settings.
14
3.5. General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and copper (Cu), and the melting point of the lead free solder is higher approx.30°C (86°F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of “PbF” is printed on the P.C.B. using the lead free solder.)
• To put lead free solder, it should be well molten and mixed with the original lead free solder.
• Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30°C
(662±86°F).
Recommended Lead Free Solder (Service Parts Route.)
• The following 3 types of lead free solder are available through the service parts route.
SVKZ000001-----------(0.3mm 100g Reel)
SVKZ000002-----------(0.6mm 100g Reel)
SVKZ000003-----------(1.0mm 100g Reel)
Note
* Ingredient: Tin (Sn) 96.5%, Silver (Ag) 3.0%, Copper (Cu) 0.5%. (Flux cored)
15
3.6. How to Define the Model Suffix (NTSC or PAL Model)
There are eight kinds of DMC-G8/G80/G81/G85 (Camera body unit), regardless of the colours.
• a) DMC-G8 (Japan domestic model)
• b) DMC-G85P/PP
• c) DMC-G80EB/EC/EF/EG, G81EG
• d) DMC-G80EE
• e) DMC-G85GN
• f) DMC-G85GD
• g) DMC-G85GK
• h) DMC-G85GC/GH
What is the difference is that the “Initial Settings” data which is stored in Flash-ROM mounted on Main P.C.B..
NOTE:
After replacing the Main P.C.B., be sure to achieve adjustment.
Refer to the adjustment instruction in the adjustment software for details.
16
3.6.2. Initial Settings:
After replacing the Main P.C.B. and/or Flash-ROM, make sure to perform the initial settings after achieving the adjustment by order-
ing the following procedure in accordance with model suffix of the unit.
1. Important Notice:
Before proceeding Initial settings, make sure to read the following CAUTION.
2. Procedures:
• Precautions: Read the above “CAUTION” carefully.
• Preparation:
Attach the fully charged Battery, and insert the memory card.
Confirm that it is not intelligent auto mode [ iA ] or intelligent auto plus mode [ iA+ ].
(If the unit is intelligent auto mode [ iA ] or intelligent auto plus mode [ iA+ ], it does not display the initial setting menu.)
The LCD displays the “ ! ” mark before the unit powers down.
17
• Step 4. Display the Initial Settings:
While pressing [ MENU/SET ] button and “[ RIGHT ] of Cursor buttons” simultaneously, turn the power off.
The “Initial Settings” menu is displayed.
There are two kinds of “Initial Settings” menu form as follows:
[ CASE 1. After replacing the Main P.C.B. and/or Flash-ROM ]
[ Except “EB/EC/EF and EG” models : SEP0848AA is used as a Main P.C.B. ]
When Main P.C.B. has just been replaced, 10 model suffixes are displayed as follows. (three pages in total)
[CASE 2. Other than “After replacing the Main P.C.B. and/or Flash-ROM”]
18
• Step 5. Cancel “Strict” mode:
Press the [ DISP. ] button to cancel “Strict” mode. (Confirm the “Strict” is disappeared.)
NOTE:
When the error message such as the following is displayed, cancel “Strict” mode.
Press [ DISP. ] button to clear the “Strict” display at the upper right corner of screen.
19
• Step 8. Confirmation:
Confirm the display of “PLEASE SET THE CLOCK” in concerned language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the “GK” model suffix is selected, the display shows “PLEASE SET THE CLOCK” in Chinese.)
As for your reference, major default setting condition is as shown in the following table.
• Default setting (After “Initial Settings”)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-G85P NTSC English Month/Date/Year
b) DMC-G85PP NTSC English Month/Date/Year
c) DMC-G80EB PAL English Date/Month/Year
d) DMC-G80EC PAL English Date/Month/Year
e) DMC-G80EE PAL Russian Date/Month/Year
f) DMC-G80EF PAL English Date/Month/Year
g) DMC-G80EG/ G81EG PAL English Date/Month/Year
h) DMC-G85GC PAL English Date/Month/Year
i) DMC-G85GD NTSC Korean Year/Month/Date
j) DMC-G85GH PAL English Date/Month/Year
k) DMC-G85GK PAL Chinese (simplified) Year/Month/Date
l) DMC-G85GN PAL English Date/Month/Year
m) DMC-G8 (Japan domestic model) NTSC/PAL NTSC/PAL Japanese/Chinese (simplified) Year/Month/Date
20
4 Specifications
4.1. Camera Body
The following specification is for DMC-G80MEB/G80HEB/G80EB/G81MEB/G81HEB/G81EB.
Some specifications may differ depending on model suffix.
21
22
23
24
25
4.2. Lens
26
27
5 Location of Controls and Components
The following description is for DMC-G80MEB/G80HEB/G80EB/G81MEB/G81HEB/G81EB.
Some descriptions may differ depending on model suffix.
The page number in this chapter does not show the page number of this service manual.
28
29
5.2. Lens
30
6 Service Mode
6.1. Error Code Memory Function
1. General Description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly.
(i.e., when the unit is powered on by the battery, the battery is pulled out)
The error code is memorized to Flash-ROM when the unit has just before powered off.
2. How to Display
The error code can be displayed by ordering the following procedure:
• Preparation
Attach the fully charged Battery, and insert the memory card.
• Step 1. The temporary cancellation of “Initial Settings”:
Set the drive mode dial to [ Single ], while pressing [ DISP. ] button and [ AF/AE Lock ] button simultaneously, turn the Power
on.
• Step 2. Execute the error code display mode:
Press [ MENU/SET ] button, [ AF/AE Lock ] button and “[ LEFT ] of Cursor buttons” simultaneously with the step 1 condition.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display Error code display Camera information display Normal display .....
31
Error Code List
The error code consists of 8 bit data and it shows the following information.
32
7 Troubleshooting Guide
7.1. Checking Method of Body and Interchangeable Lens
1. Initial (Default) Status Of The Lens Unit
The Lens unit which is supplied as a standard accessory for this camera unit (H-FS12060, H-FS14140, H-FS1442A) shows
the following status when the Lens is detached from the Camera unit.
NOTE: Although the lens unit is attached it shows the same condition when the Camera turns off.
If it is hard to determine whether the resolution is out of specification or not, proceed the “RESOLUTION INSPECTION”,
before replacing the Lens Main Unit. (The unit might be mishandling, dropping or others.)
33
3. Reference information
34
35
36
7.2. Wi-Fi Circuit (Jack P.C.B.)
7.2.1. How to Remove Wi-Fi Password Protection
To prevent incorrect operation or use of the Wi-Fi function by a third party and to protect saved personal information, this unit pro-
tects the Wi-Fi function with a password.
It is unable to service with password locked condition. When accepting for repair, the unit has been set the Wi-Fi password by cus-
tomer, run the [ Reset Wi-Fi Settings ] for removing Wi-Fi password, then check the operation.
37
8 Service Fixture & Tools
8.1. Service Fixture and Tools
The following service fixture and tools are used for checking and servicing this unit.
38
39
8.2. Clean Box
• The repair quality is considered, and it is recommended working in the environment of specified clean level less than class
10,000 (Federal Standard 209D).
[NOTE]
• Work in the environment of specified clean level less than class 10,000 (Federal Standard 209D) when inside cleaning of a lens.
Please refer to the following service manuals.
• H-FS12060E/GK/PP: Order No.DSC1604008CE
• H-FS14140PP/E/GK: Order No.DSC1305023CE/Order No.DSC1506509SE
• H-FS1442APP/E/GK: Order No.DSC1302014CE/Order No.DSC1506508SE
40
8.4. Service Position (When checking the each P.C.B.)
This service position is used for checking and replacing parts. Use the following extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection From
1 RFKZ0477 FP9301(MAIN P.C.B.)LCD UNIT 45pin / 0.3 FFC
2 RFKZ0583 FP9002(MAIN P.C.B.)REAR CASE UNIT 19pin / 0.3 FFC
41
8.5. Service Position (Flange Back Adjustment)
This service position is used for checking and replacing parts. Use the following extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection From
1 RFKZ0477 FP9301(MAIN P.C.B.)LCD UNIT 45pin / 0.3 FFC
2 RFKZ0583 FP9002(MAIN P.C.B.)REAR CASE UNIT 19pin / 0.3 FFC
3 VFK1950 FP9001(MAIN P.C.B.)TOP CASE UNIT 33pin / 0.3 FFC
42
9 Disassembly and Assembly Instructions
9.1. Camera Body Part
9.1.1. Disassembly Flow Chart
This is a disassembling chart.
When assembling, perform this chart conversely.
43
9.1.3. Disassembly Procedure No. Item Fig. Removal
6 BIS Unit, (Fig. D17) Screw (U?×3
Shutter Unit BIS Unit
No. Item Fig. Removal Adjust Spring x 3
1 Rear Case Unit (Fig. D1) Screw (A) x 3 (Fig. D18) Screw (V) x 1
Screw (B) x 1 Screw (W) x 2
Screw (C) x 1 Damper O Ring
Screw (D) x 1 Shutter Unit
(Fig. D2) Front Grip L 7 Mount, (Fig. D19) Screw (X) x 1
Screw (E) x 1 Mount Ring, Screw (Y) x 1
(Fig. D3) Locking tab x 3 Mount Spring, Screw (Z) x 2
Rear Grip Unit Lens Connector Screw (a) x 2
Screw (F) x 1 Mount
Screw (G) x 2 Mount Ring
(Fig. D4) Eye Cup Unit Mount Spring
Screw (H) x 2 Lens Connector
Screw (I) x 1 8 BG Contact FPC Unit, (Fig. D20) Screw (b) x 1
Screw (J) x 1 BG Shading Piece, Screw (c) x 3
FP9301 (Flex) Tripod Unit Screw (d) x 2
FP9002 (Flex) Convex x 2
Rear Case Unit BG Contact FPC Unit
(Fig. D5) (When Assembling BG Shading Piece
the Rear Grip Unit) Tripod Unit
(Fig. D6) (When Assembling 9 Jack P.C.B. (Fig. D21) Screw (e) x 2
the Front Grip L) Screw (f) x 1
2 Top Case Unit, (Fig. D7) FP9001 (Flex) FP4403 (Flex)
Flash P.C.B. FP9004 (Flex) Front Wp Poron A
FP9007 (Flex) FP4402 (Flex)
FP9302 (Flex) Convex x 1
Screw (K?×1 Jack P.C.B.
(Fig. D8) Front Grip R 10 Battery Door Unit, (Fig. D22) Battery Door Shaft
Screw (L?×2 Battery Out Spring Battery Door Spring
(Fig. D9) Screw (M?×2 Battery Door Unit
Flash Case Top Battery Out Spring
Flash Case Packing 11 LVF Unit (Fig. D23) Screw (g) x 2
Screw (N?×1 LVF Unit
(Fig. D10) Hooking part x 1 12 Rear Plate Unit, (Fig. D24) FPC Tape
Screw (O?×2 Speaker Solder (2 points)
(Fig. D11) Convex x 2 Convex x 2
Battery Connect Cover Screw (h) x 5
(Fig. D12) Convex x 2 Screw (i) x 4
Solder (4 points) Screw (j) x 1
Top Case Unit Convex x 2
Flash P.C.B. Sensor Earth Plate
(Fig. D13) (When Assembling (Fig. D25) Convex x 2
the Front Grip R) Hinge Arm Cover Top
3 Main P.C.B. (Fig. D14) FP3501 (Flex) Hinge Arm Cover Bottom
FP3502 (Flex) Rear Plate Unit
FP9003 (Flex) Speaker
FP9005 (Flex) 13 Operation Buttons (Fig. D26) Cursor Button Packing
FP9006 (Flex) Operation Buttons
FP9009 (Flex) 14 MR1 SW FPC, (Fig. D27) Solder (6 points)
FP9901 (Flex) LCD Unit Convex x 6
Screw (P) x 2 Hinge Cushion 4
Screw (Q) x 2 Hinge Fix Cover
Gasket MR1 SW FPC
Main P.C.B. (Fig. D28) Screw (k?×1
4 Main Heat Sink (Fig. D15) Screw (R?×1 Screw (l?×1
Screw (S?×2 Hinge Earth Plate
Convex x 2 LCD Lock Holder
Main Heat Sink LCD Unit
5 Battery Unit (Fig. D16) Screw (T?×2
Battery Unit
44
9.1.3.1. Removal of the Rear Case Unit
(Fig. D2)
(Fig. D1)
45
(Fig. D3) (Fig. D4)
46
(Fig. D5)
(Fig. D6)
47
9.1.3.2. Removal of the Top Case Unit and
Flash P.C.B.
(Fig. D8)
(Fig. D7)
48
(Fig. D10)
(Fig. D9)
49
(Fig. D12)
(Fig. D11)
50
9.1.3.3. Removal of the Main P.C.B.
(Fig. D14)
(Fig. D13)
51
9.1.3.4. Removal of the Main Heat Sink 9.1.3.6. Removal of the BIS Unit and Shut-
ter Unit
(Fig. D15)
(Fig. D17)
(Fig. D16)
52
9.1.3.7. Removal of the Mount, Mount
Ring, Mount Spring and Lens
Connector
53
9.1.3.8. Removal of the BG Contact FPC 9.1.3.9. Removal of the Jack P.C.B.
Unit, BG Shading Piece and Tri-
pod Unit
54
9.1.3.10. Removal of the Battery Door Unit 9.1.3.12. Removal of the Rear Plate Unit
and Battery Out Spring and Speaker
(Fig. D22)
(Fig. D23)
(Fig. D24)
55
9.1.3.13. Removal of the Operation Buttons
(Fig. D26)
(Fig. D25)
56
9.1.3.14. Removal of the MR1 SW FPC and
LCD Unit
(Fig. D27)
(Fig. D28)
NOTE: (When Installing)
Make sure to confirm the following points when installing:
• The screw is tightened enough.
• Installing conditions are fine. (No distortion, no abnormal-
space.)
• No dust and/or dirt on image sensor surface. (live mos)
• LCD image is fine. (No dust and/or dirt on it, and no gradient
images.)
57
9.2. Disassembly and Assembly
Procedure for the Lens
Please refer to the following service manuals about Disassem-
bly and Assembly of bundled lenses.
• H-FS12060E/GK/PP: Order No.DSC1604008CE
• H-FS14140PP/E/GK: Order No.DSC1305023CE/
Order No.DSC1506509SE
• H-FS1442APP/E/GK: Order No.DSC1302014CE
/Order No.DSC1506508SE
58
10 Measurements and Adjustments
10.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software.
NOTE:
After adjustments have been terminated, make sure to achieve “Initial Settings”.
After updates it to the latest firmware, the adjustment is executed.
59
*2 NOTE: (About Simplicity flange back adjustment)
When remove or turn the flange back adjustment screw, “Simplicity flange back adjustment” is necessary.
When remove the flange back adjustment screw, please don’t reuse it. Use new one.
The image sensor of this camera cannot be fixed when power is OFF.
That is why, image sensor adjustment have to do power ON after assembly (state of above).
Stand-alone mount part cannot adjust.
60
*4 NOTE: (When exchange the Main P.C.B. and/or Flash-ROM (IC6003))
After exchanging the “Main P.C.B. and/or Flash-ROM”, first, execute “Initial Settings” to determine the model suffix,
and then, cancel the “Initial Settings” and proceed the adjustments.
When the adjustment data is rewrite without “Initial Settings” execution, may not be able to choose desire model suffix.
During the “Initial Settings” (When the model suffix select screen is displayed), do not power off or do not remove the battery.
* Power down during “Initial Settings” may cause not be able to choose desire model suffix.
When cannot be repaired in the IC exchange, and in the case of performing the “Main P.C.B.” exchange, carry out any of follow-
ing.
1. When it can turn on power, and the adjustment software can communicate with the camera body:
Before replacing, proceed the Flash-ROM (IC6003) data backup from the unit.
After replacing, overwrite the Flash-ROM (IC6003) data with backup data from the unit.
After that, proceed the main body adjustment. (Almost adjustment/inspection items can be omitted.)
Refer to the adjustment instruction in the adjustment software for details.
2. When it cannot turn on power, or the adjustment software cannot communicate with the camera body:
Almost readjustment fully are necessary.
The details are refer to adjustment manual in adjustment software.
61
11 Maintenance
11.1. Notice in External Cleaning
11.1.1. About the Body
NOTE:
Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the memory card and lens unit.
62
12 Block Diagram
12.1. Overall Block Diagram
MEMORY
MOUNT BOX UNIT CARD
MOS IMAGE SENSOR
LENS UNIT 4/3” 16 MEGA PIX
(Built in AFE) SPEAKER
IC9180
(27MHz) SYSTEM IC ECM(L)
SSWF LENS CONTACT SHUTTER BIS UNIT STEREO
TERMINAL UNIT MICROPHONE AMP MICROPHONE
SPEAKER AMP ECM(R)
VIDEO OUT
USB
GYRO TERMINAL
Q9801, T9801 (PITCH/YAW)
IC5001
BIS DRIVER IC6001
GYRO IC5101 VENUS ENGINE HDMI
(ROLL) GYRO AMP TERMINAL
CAMERA PROCESS
J-PEG COMP/EXPANDS
EXT. FLASH HOT SHOE MEDIA I/F
(OPTION) UNIT QR8002,8003 USB I/F
MAIN MICROPROCESSOR
OIS CONTROL Wi-Fi
IC9133,9134,9162
LENS DRIVE ANTENNA
LOGIC IC
LCD DRIVE
LP-DDR2 MOBILE RAM /8G-bit
Q8501 HDMI DRIVER W-LAN MODULE
IC8501
FLASH CHARGE
CHARGE CONTROL
DRIVE
BATTERY GRIP
REAR OPERATION CONTROLS (OPTION)
IC1901,1902,6004,6005
X6001
AND GATE IC/
(48MHz) NAND GATE IC
IC9180
SYSTEM IC IC1001,1031,1091,9103
8ch SW REGULATOR BATTERY
(POWER SUPPLY)/ PACK
DC-DC CONVERTER/
SYNCHRONOUS STEP
-DOWN CONVERTER/
REGULATOR
X9101
IC6003
(32.768kHz) NAND FLASH ROM/1G-bit
IC1051,1231,1251,1411
TOUCH PANEL IC1431,1451,1471,1491
IC1611,1621,6501-6506
TOP OPERATION CONTROLS
COLOR LCD IC9113,9201,9202,9203
PANEL IC9301
3.0” PANEL REGULATOR/LOAD SW/
1040k dots DC-DC CONVERTER/
BUS SW
COLOR LVF
0.39” PANEL
2360k dots
IC2701
EYE SENSOR
LEVEL METER
63
12.2. System Control Block Diagram
IC9180
(SYSTEM IC) TOP OPERATION FPC
FP9001
PW D3.15V
8,25 (Green)
(LED PWR OUT) (LED PWR OUT) FP9001
LEDOUT0 B2 POWER LED
9
LEDOUT3 A3
(LED AF OUT) (AFLED Cathode) FP9001
LEDOUT2 B3 AF LED
24
FP9001
PW D5.2V (Blue)
10
(LED WiFi OUT) (WiFi LED K) FP9001 Wi-Fi LED
LEDOUT1 C4 11
(FN1 ON L) (FN1 ON L) 2 4
FP9001 FRONT FN
PIOA3 C2
16
(REC ON L) (MOVIE ON L) FP9001 1 3
PIOD4 B4 REC
15
(REAR FN ON L) (REAR FN ON L) FP9001
PIOA2 B1 REAR FN
(SHUTTER0) 3
PW D3.15V 2 4
SHUTTER0 L7 (REAR DK) FP9001
(AF AE LOCK) 1
PIOA0 A1 (CMD DIAL R0) 1 3
FP9001
IC6001 2
X9101 RL9101 (VENUS ENGINE)
(32.768KHz)
(CLK27 SYS) (CLK27 SYS) (CMD DIAL R0) (CMD DIAL R1) FP9001
L5 OSC IN MCLK L1 H3 P1 2 4
5
(SYS RESET) (SYS RESET) (CMD DIAL R1) (FRONT DK)
RESETOUT H7 U7 FP9001
P7
18 1 3
K5 OSC OUT RL9118 (CMF DIAL F0) (CMD DIAL F0) FP9001
(SHUT HALF) (SHUT HALF) R4
SHUTTERHALF E5 K4 19
RL9114 (CMD DIAL F1) (CMD DIAL F1) FP9001
(S SYS SDIN) (S SYS SDIN) P6 2 4
SO G4 J3 12
RL9112 PW D3.15V PW D3.15V
(S SYS SCK) (S SYS SCK)
SCLK J1 J2 1 3
(S SYS SDO) RL9113 (S SYS SDO)
SI H3 J4 FP9001
RL9111 PW D3.5V
(S SYS CS) (S SYS CS) 7,17
CS K1 H1
(LCD OPEN H) IC2701
PIOA6 F6 (LEVEL METER) 4 5 6 4 5 6
(LCD ROTATE2) SHUTTER MODE DIAL
PIOA5 J11
(LCD ROTATE1) CS 8 PW D3.15V Q9002 Q9003
PIOA4 G7 CH2701 VDD 1
(LCD EVF SEL) 11 INT1 15 3 2 1 3 2 1
Reserved
PIOD2 C5
VS 14
CH2702 (G I2C DAT AD)
9 INT2 SDI 6 D11 CD9009
(G I2C CK AD)
SCL 4 C11 (SHUTTER HALF) FP9001
HOT SHOE FPC 21
FLASH DET FPC (SHUT FULL) (SHUTTER FULL) FP9001
J1
20
FP9007 CH6024 PW D3.15V (MODE DIAL0) (MODE DIAL0) FP9001
RL9401 RL7118 RL7119 V3
INT STB DET 23 26
FP9007 (INT STB DET) (INT STB DET) (MODE DIAL1) (MODE DIAL1) FP9001
RL9402 G16 V2
22 28
DRIVE MODE DIAL FP9007 (DRIVE DIAL) (DRIVE DIAL) PW A1.8V PW D3.15V
V4 REAR OPERATION FPC
24
FP9002
(EYE SENSOR)
17
(REAR KEYIN2) (DISP ON L) FP9002
LCD LVF SEL D21 DISP.
5 LEDK VDD 1 PW D3.15V 9
FP9007 (LCD EVF SEL) (SET ON L) FP9002
PW A1.8V MENU/SET
6 LDR 27 12
LEDA 4
(Fn4/DEL) FP9002
FP9007 (EYE SCL) (G I2C CK) Fn4/DEL
SCL 2 K2 19
3 GND 2 (REAR KEYIN1) (Fn2/Q.MENU) FP9002
FP9007 (EYE SDA) (G I2C DAT) C21 Fn2/Q.MENU
7 INT SDA 8 K3 6
5 (PLAY ON L) FP9002 PLAY
16
(CROSS KEYIN) (RIGHT ON L) FP9002
B21 RIGHT
X6001 10
(48MHz) (UP ON L) FP9002
UP
MR1 SW FPC HINGE FPC AC27 11
(LEFT ON L) FP9002 LEFT
RL9503 18
(DOWN ON L) FP9002 DOWN
MR1 (LCD ROTATE1) FP9301 (LCD ROTATE1) AD27
PW A1.8V 13
RL9501 3 (AF AE LOCK) FP9002 AF/AE LOCK
(LCD ROTATE2) (LCD ROTATE2) 1
FP9301 (FOCUS MODE) (FOCUS MODE AF) FP9002
MR2
1 PW A1.8V W6 3
(FOCUS MODE MF) FOCUS MODE
PW D3.15V FP9002
PW A1.8V 4
FP9002
2,5
(V9 THERMO) (REAR THERMO) PW A1.8V (REAR THERMO) FP9002
W4 V1
LCD IF P.C.B. 14
MR3 SW FPC (AV KEY DET) FP9002
CH4110 TH6001 W7 15
(REMOTE ZOOM)
MR3 A21
(X MR3 sig) FP4104 (LCD OEN H) FP4101 FP9301 (LCD OPEN H) (REMOTE REC)
G19
3 37 1 JACK P.C.B.
PW A1.8V
PW D3.15V
(AV KEY DET) (REMOTE TERMINAL)
CH4107 FP9009 FP4401
4 5 6 1
17 16
FP4103 (TSP INT) FP4101 FP9301 (TSP INT) (TP INT) (REMOTE ZOOM) FP9009 FP4401 3
AD10
53 36 43 18 17
CH4105 Q9041 (REMOTE REC) 5
FP9009 FP4401
TOUCH FP4103 (TSP SCK) FP4101 FP9301 (TSP SCK) 3 2 1
19 18 6
PANEL 51 34 41 4
CH4104 SLLK FPC UNIT
CD9005 2 CD4401
FP4103 (TSP SDA) FP4101 FP9301 (TSP SDA)
(LPSW) (LPSW) FP9009 FP4401 (LPSW) FP4403
50 33 40 M3
1,2 1 4,5,6
LCD UNIT
DMC-G80/G81/G85 SYSTEM CONTROL BLOCK DIAGRAM
64
12.3. Video/Audio Process (1) Block Diagram
IC6003
(NAND FLASH ROM/1G-bit)
41 48 56 57 58 59 52 17 8 7 12 10 16 11
DAT0
DAT7
CLE
ALE
NWP
RY/NBY
NCE
NRE
NWE
IMAGE SENSOR UNIT
(SENSOR)
IS P.C.B. IC6001
(VENUS ENGINE)
R25 R24 R23 T27 T26 T25 T24 T23 N23 P27 P26 P25 P24 P23 R26
FP3002 FP3502 (SD0DA0P)
C2 M27 FL2001 JK2002
38 39 (G HDMI D2+)
FP3002 FP3502 (SD0DA0M) AG24 1 5 3 D2+
C1 M26 (G HDMI D2-)
37 38 AF24 2 6 5 D2-
FP3002 FP3502 (SD0DA1P) (G HDMI D1+)
D2 L24 AG23 3 7 6 D1+
35 36 (G HDMI D1-) FL2002
FP3002 FP3502 (SD0DA1M) AF23 4 8 8 D1-
D1 L25 (G HDMI D0+)
34 35 AG22 1 5 9 D0+
FP3002 FP3502 (SD0DA2P) (G HDMI D0-)
11 D0-
HDMI
E2 J27 AF22 2 6
32 33 (G HDMI CK+)
12 CK+
TERMINAL
(SD0DA2M) AG21 3 7
FP3002 FP3502 (G HDMI CK-)
E1 J26 AF21 4 8 14 CK-
31 32 (HDMI CEC)
FP3002 FP3502 (SD0CAP) AA23 15 CEC
F2 G26
29 30 17 SCL
FP3002 FP3502 (SD0CAM) 18 SDA
F1 G27
28 29 (G HDMI SDA)
(SD0DA3P) AB24 1 HPDTCT
FP3002 FP3502
G2 E25 19 PW D5R
26 27 Q2002
FP3002 FP3502 (SD0DA3M) PW D3.15V PW HDMI5.0V
G1 E24
25 26 6 5 4
FP3002 FP3502 (SD0DB3P)
L2 L26
23 24
FP3002 FP3502 (SD0DB3M) 4 5 6
L1 L27 Q2001
22 23 (READ SCL)
FP3002 FP3502 (SD0CBP) B11
M2 K27
20 21 1 2 3 QR2001
FP3002 FP3502 (SD0CBM) (G HDMI SCL)
MOUNT MOS
M1
19 20
K26 AB23
BASE IMAGE FP3002 FP3502 (SD0DB2P)
3 2 1
N2 E27
UNIT SENSOR
17 18
FP3002 FP3502 (SD0DB2M) (HDMI HPD)
16MEGA PIX N1 E26 AC24
16 17
(Built in AFE) FP3002 FP3502 (SD0DB1P) P9201
P2 F26 (MEMORY CARD CONNECTOR)
14 15 CH6027 CH6026 CH6001 CH6019
FP3002 FP3502 (SD0DB1M)
P1 F27
13 14 (G SD0 U2 D0P)
FP3002 FP3502 (SD0DB0P) AA27 11 D0+
R2 H27 (G SD0 U2 D0M)
11 12 AA26 12 D0-
FP3002 FP3502 (SD0DB0M) (G SD0 U2 D1M)
R1 H26 Y27 15 D1-
10 11 (G SD0 U2 D1P)
FP3002 FP3502 (IS SCK) Y26 16 D1+
A14 A22 (SD0 DAT2)
7 8 V27 9 DAT2
FP3002 FP3502 (IS SDO) (SD0 DAT3)
B14 C22 V26 1 CD/DAT3
6 7 (SD0 CMD)
FP3002 FP3502 (IS CS) U26 2 CMD
B13 B22 (CLK SD0) VSS1
5 6 U27 5 CLK 3
(IS THERMO) PW A1.8V (CKG SD0 DAT0) VSS2
FP3002 FP3502 7 DAT0/RCLK+ 6
W3 W27
2 3 (CKG SD0 DAT1) VSS3
W26 8 DAT1/RCLK- WP 10
CH3502 (SDWP) WP VSS4
FP3001 FP3501 (VD) B7 WP 13
A13 B23
23 22 CH3501 CD9203 CD VSS5
(HD) PW SD3.15V CD 17
FP3001 FP3501
A12 A23 V20 C.DET
24 23 (PW SD0 3018V) VDD2 14
FP3001 FP3501 (IS PSV) V21
B11 AE12 VDD/VDD1 4
25 24 QR9202
FP3001 FP3501 (CLK27 IS FCK) (SSWFOUT SYS) IC9201
A11 R27 D27 (BUS SWITCH)
10 9 CD9201
(SSWF ON H)
E22 PW SD3.15V
(REGULATOR) 1 OE1 VCC 8 PW SD3.15V
(SDCD SYS)
A7 2 A1 OE2 7 Q9201
FP3001 FP3501
PW IS1.8V 1 VOUT VIN 4 PW D3.15V 3 B1 B2 6
27 26
2 VSS CE 3 4 GND A2 5 4 5 6
T9801
65
12.4. Video/Audio Process (2) Block Diagram
IC6001 IC9180
(VENUS ENGINE) (SYSTEM IC)
RL9103
(CLK27 SYS)
H3 L1 MCLK
CD9006 10 -INPUT D
(GUN DET) 16 -INPUT A
V7 20 -INPUT B
CD9007
(EXT MIC DET) (EXT MIC DET) FP9009 FP4401
D17
20 19
(EXMIC GND) FP9009 FP4401
CD9110 28,29 27-29
(W-LAN MODULE)
Wi-Fi
(G WiFi CLK) (G WiFi CLK) FP9009 FP4401 ANTENNA
A8 12 SDIO CLK
5,6 3
(WiFi CMD) (WiFi CMD) FP9009 FP4401
B8 13 SDIO CMD
11 7
(WiFi DAT0) (WiFi DAT0) FP9009 FP4401
C8 11 SDIO D0
5,6 6
(WiFi DAT1) (WiFi DAT1) FP9009 FP4401
D8 11 10 SDIO D1
5
(WiFi DAT2) (WiFi DAT2) FP9009 FP4401 FP4402
C9 15 SDIO D2 2.4G ANT 31
5,6 9 1-4
(WiFi DAT3) (WiFi DAT3) FP9009 FP4401 RL8401
D9 11 14 SDIO D3
8
(WiFi RESET) FP9009 FP4401
29 RESET N
5,6 13
JK2003
L2001 (MICRO USB TERMINAL)
CD2001
(G USB-)
AF16 2 3 2 D-
(G USB+) CD2002
AG16 1 4 3 D+
(USB VBUS) CD2003
AC18 1 VBUS
66
12.5. Video/Audio Process (3) Block Diagram
LCD UNIT
4 5 6
CA LCD FP4102
1,2
AN LCD(18.0V) FP4102
3,4
FP9302
41
AD9 FP9302
BUS54 EVF0-15 BUS54 EVF0-15 34
AE5 FP9302
CH9302 31
(S EVF SDO)
W25
(S EVF SCK)
CH9303 LVF
V24 FP9302
24
CH9301
(S EVF SDIN) SO FP9302
V23
CH9304 17
(S EVF CS) XCS FP9302
W24 20
(EVF RST) XCLR FP9302
AD12
50
IC9301 SI FP9302
IC9180 (DC/DC CONVERTER) 18
(SYSTEM IC) XSCK FP9302
LX
3 CD9301 19
RL9134 VCC
PW D3.15V 5
FB VDD2(10V) FP9302
(LCD BLT) 2
PIOC2 D9 3,59
ERR. PW UNREG SYS
VREF
AMP
CH9305 CE UVLO VOUT
SOFT-START 6
(EVF POWER) ENB PWM
PIOC1 C10 1 COMP.
R Q DRIVER 6 5 4
S CONTROL
OVP 3 2 1 Q9301
OSC
GND 4 5 6
4
PW D3.15V QR9301
67
12.6. Gyro Block Diagram
IC6001
(VENUS ENGINE)
GYRO FPC
5 GND VDDM 6
IC5001
(BIS DRIVER)
FP9005 (PW DGYRO VDDM)
PW GY3.0V
(CLK9 SAMBA) 21
CLOCK A2 FP9005 (PW DGYRO VDDI)
PW VDD33
20
CH6031
(SAMB S SDOUT) (SAMB S SDOUT) FP9005 (S GYRO MISO)
(SAMB S CS) CSIO RXD A3
C16 A1 CSIO CS SRDY N 15
(SAMB S SCK) (SAMB S SCK) FP9005 (S GYRO SCK)
CSIO SCLK C2
(SAMB M SCK) 16
L2 D2 CSIO HS SCLKI
(SAMB M SDIN) (GYRO SENSOR:PITCH)
L3 C3 CSIO HS TXD
(SAMB S SDIN) (SAMB S SDIN) FP9005 (S GYRO MOSI)
CSIO TXD B2 1 MOSI SCLK 10
(SAMB M SDOUT) 17
L4 C1 CSIO HS RXD (G GYRO CS) (S GYRO CS) FP9005 (S GYRO CS)
P00 G2 2 SS MISO 9
18
PW D3.15V 3 VDDL VDDI 8
4 Reserved DRY 7
(TILT SENSOR)
68
12.7. Flash/Hot Shoe Block Diagram
C G A
CH8001
(STX) FP9007 STX
RL7108
12-14
IC6001
(VENUS ENGINE) (TXD) FP9007 STTXD
RL7106
6
HOT SHOE
(RXD) FP9007 STRXD
RL7107
7
PW D3.15V
PW D3.15V
CH8003 4 5 6
PW D3.15V
3 2 1
QR8003
4 5 6
(EXT STRTTL)
T1
IC9180
(SYSTEM IC) FLASH P.C.B.
3 2 1
RL8503
69
12.8. Lens Block Diagram
IC6001
IC9901 (VENUS ENGINE)
(SHUTTER DRIVER)
CH9901 CH9910
FP9901 (SHUT MT1 B)
MOT 1B 11 OUT1B IN1B 7 F17
4,5 CH9002 CH9909
FP9901 (SHUT MT1 A)
MOT 1A 10 OUT1A IN1A 6 F16
6,7 CH9903 CH9906
FP9901 (SHUT MT2 A)
MOT 2A 15 OUT2A IN2A 19 F18
8,9 CH9004 CH9907
FP9901 (SHUT MT2 B)
MOT 2B 14 OUT2B IN2B 18 G18
10,11 CH9908 (M DRIVE CTL)
5 CR1 PS 2 C15
CH9917 CH9911
VLIM1 3
IC9180
(SYSTEM IC)
20 CR2 SENSE2 21
RNF2 13
CH9916 CH9905 (SHUT DAC1)
VLIM2 22 G8 DACOUT0
CH9918
4 SENSE1
(SHUTTER FPC) 12 RNF1 VREF 23 PW VDD33 (SHUT DAC2)
VCC 24 G9 DACOUT1
1 GND VM1 9 PW SHUT11.0V
VM2 16
CH9912 (SHUT PI E1)
FP9901
PI 1C E A12
1 CH9914
FP9901
PI 1C K
2
FP9901
PI 2C K
14 CH9913
FP9901 (SHUT PI E2)
PI 2C E B13
13
FP9901 ( SHUT THERMO)
SHUT THERMO U2
15
IC5001
(BIS DRIVER)
(PIT )
FP3001 FP3501 (YHI-)
4 OUT- IN- 3 Q5001 B6 HA2Y OUT
21 20
FP3001 FP3501 (YHO+)
1 IN+ OUT+ 2 C6 HA2Y INN
20 19
FP3001 FP3501 (YHO-) D6 HA2Y INP
19 18
FP3001 FP3501 (Hall IN+)
12 11 PW A3.0V
(Yaw1)
D8 OUT5A
FP3001 FP3501 (X1HI-)
4 OUT- IN- 3 16 15
(X1HO+) (SHUT PI K)
FP3001 FP3501 PI1 B5
1 IN+ OUT+ 2 C4 HA2X INP
17 16
FP3001 FP3501 (X1HO-) J7 HAX DAOUT
(Yaw2) 18 17
D5 HA2X INN
(MOUNT BASE UNIT) FP3001 FP3501 (X2HI-)
4 OUT- IN- 3 C5 HA2X OUT
13 12
FP3001 FP3501 (X2HO+) H4 ADIN EXT1
1 IN+ OUT+ 2
14 13 J8 HDX IN CH5051
FP3001 FP3501 (X2HO-)
PW A3.0V K8 HDX SEN (SHUT PI CTL) (SHUT PI CTL)
15 14 INA F6 D18
CH3556 K9 HDY IN
FP3001 FP3501 (X2DR-)
RL3004 K10 HDY SEN
5 4
FP3001 FP3501 (X2DR+)
RL3003 F4 HA1X INP
6 5
(YDR+) G5 HA1X INN
FP3001 FP3501
RL3001
7 6 CH3554 G6 HA1Y INP
FP3001 FP3501 (YDR-) H6 HA1Y INN
RL3002
8 7
FP3001 FP3501 (X1DR+)
RL3005 E8 OUTIS2B
37 36 CH3552
FP3001 FP3501 (X1DR-) D9 OUTIS2A
RL3006
38 37 G8 OUT3A
G9 OUT3B PW D3.15V
F7 OUTIS1A
E7 OUTIS1B
FP9006 PW LEN4.2V
LEN4R2V
16-21 CH9001
FP9006 (LSDET) (LSDET)
LSDET A14
8 CH9002
FP9006 (LSRST) (LSRST)
LSRST A13
7 CH9003
FP9006 (S LSB2L) (S LSB2L)
LSB2L F13
6 CH9004
FP9006 (S LSL2B) (S LSL2B)
LSL2B D13
(LENS FPC) 5 CH9005
FP9006 (S LSDIO) (S LSDIO)
LSDIO G13
4 CH9006
FP9006 (S LSCK) (S LSCK)
LSCK F12
3 CH9007
FP9006 (S LSB2A) (S LSB2A)
LSB2A C13
2 CH9008
FP9006 (S LSLDPO) (S LSLDPO)
LSLDP F14
1
70
12.9. Power(1) Block Diagram
FLASH P.C.B.
CD9001 CD1903 CD1001
CC8502
P8501
IP8501 (UNREG) (PW UNREG1)
BAT+ FP8501 FP9004
1 PW UNREG
27-33 26-33
To FP8501 FP9004 (THERMO) IP1901
BAT THERMO 2
BATTERY 19 18 4 5 6 6 5 4 PW STB UNREG
CC8501
CATCHER BAT DET 3 IP1002
FP8501 FP9004 (UNREG GND/D GND) PW UNREG SYS
BAT- 4
8-10,13, 8,9,12
15,20-25 14,19-24
3 2 1 1 2 3
PW EVER 3V
FP8501 FP9004 (BACK BAT+)
B8501 14 13
Q1902 IC6001
BACK BATT
Q1905 IC1901 (VENUS ENGINE)
(AND GATE IC)
1A (BAT1 SEL)
VCC 1
PW D3.15V 5 C19
1B
2
TOP OPERATION FPC 1Y
Q1907 4 GND 3
Q1901
POWER SW
CD9008 QR1901
OFF ON
FP9001 (POWER ON L)
31
PW A1.8V
IC9180
(SYSTEM IC)
(EVER 3V)
EV3 K6
6 5 4
OVERCUT H8
Q1906 IC1902
(AND GATE IC)
IC9103 1 2 3 VCC 1A (BAT1 ON)
FBREG K10 (REGULATOR) PW D3.15V 5 1 B20
1B (BAT2 SEL)
2 D19
6 CE VIN 1 1Y
CD1902 Q1908 4 GND 3
5 VSS NC 2
4 NC VOUT 3
(BAT2 ON)
QR1902 C19
IC6004
(SINGLE BILATERAL
ANALOG SWITCH)
(VG ON DET)
PIOD5 D5 1 A VCC 5
2 B
3 GND C 4
BG FPC
W1
BATTERY GRIP TERMINAL
FP9003 (VG ON DET) CD9003 IC6005
35 (SINGLE BILATERAL
FP9003 (UNREG) ANALOG SWITCH)
9-16
(SW UNREG2)
FP9003 (BIAS2) 1 A VCC 5
5
FP9003 (BIAS1) 2 B
PW A1.8V
27
FP9003 (BATT2 AD)
3 GND C 4
28
FP9003 (VG DET)
2 W2
FP9003 (VG KEYIN)
(VG DET)
3 B19
FP9003 (BAT2 THRMO)
(VG KEYIN)
6 V6
FP9003 (CMD DIAL VF1)
(BAT2 THERMO)
29 CH9014 U3
FP9003 (DIAL VG CTL) (CMD DIAL VF1)
30 AG12
FP9003 (CMD DIAL VF0) (DIAL VG CTL)
31 T4
FP9003 (CMD DIAL VR1) (CMD DIAL VF0)
33 AF14
FP9003 (CMD DIAL VR0) (CMD DIAL VR1)
34 AA16
(CMD DIAL VR0)
AD14
71
12.10. Power(2) Block Diagram
CD1701
PW UNREG PW LEN4.2V
CD1202
PW SD3.15V
CD1101
PW D1.2V 1
CD1301
PW D1.2V
CD1201
PW D3.15V
IC1451
(REGULATOR) CD1451
IC1001
(8CH SW REGULATOR)
4 VIN VOUT 1 PW AVCC33
Hx1
VO1 61
4 Hx1 3 CE VSS 2 IC1471
HVREG 62
Lx1 (REGULATOR) CD1471
DRIVER 63
CH1 Lx1
STEP DOWN DC/DC 64 4 VIN VOUT 1 PW DVCC18
VREGD
(Current mode) PGND1
DRIVER 59
ERROR AMP1 PGND1
SERIAL I/F
VO2 60 3 CE VSS 2
5
57
Hx2 IC1491
HVREG (REGULATOR) CD1491
DRIVER
CH2 Lx2 4 VIN VOUT 1
58 PW VDD33
STEP DOWN DC/DC VREGD
(Current mode)
DRIVER
SERIAL I/F
ERROR AMP2 PGND2 IC1231 3 CE VSS 2
VO3 56 (REGULATOR) CD1231
6 Hx3
54
Vo3SEL HVREG 4 VIN VOUT 1 PW A1.8V
DRIVER
CH3 Lx3
STEP DOWN DC/DC 55
VREGD
(Current mode)
52
PGND3 3 EN VSS 2 IC1431
DRIVER (REGULATOR) CD1431
ERROR AMP3 PGND3
VO4
SERIAL I/F 53
7 Hx4 4 VIN VOUT 1 PW D1.8V
HVREG 49
Hx4
DRIVER 50
CH4 Lx4 3 EN VSS 2
STEP DOWN DC/DC 51
VREGD CD1601
(Current mode) PGND4
DRIVER 48
ERROR AMP4 PW D5.2V
SERIAL I/F Hx5
VO5 44
8 Hx5
HVREG 45 CD1401
Lx5
DRIVER 46
CH5 Lx5 PW D3.5V
47
STEP DOWN DC/DC VREGD IC1411
(Current mode) PGND5 (REGULATOR) CD1411
DRIVER 42
ERROR AMP5 PGND5
SERIAL I/F 43
VO6 4 VIN VOUT 1 PW A3.1V
9 Hx6
38
HVREG
Hx6
DRIVER 39
CH6 Lx6 3 CE VSS 2
STEP DOWN DC/DC 40
(Current mode) VREGD IC1251
Lx6 (DC/DC CONVERTER)
DRIVER 41
ERROR AMP6
SERIAL I/F PGND6 D1271
36 VIN
PGND6 1 1
37 3
INV7 RAMP CURRENT 2
32
VREGD 35 Lx7 COMPENSATION + FEEDBACK
CD1251
CH7 DRIVER PGND7
STEP UP DC/DC 34 CURRENT LX
ERROR AMP7 6 PW EVF1.8V
0.3V (Current mode) VO7 OSCILLATOR PROTECTION
33
SERIAL I/F SHUTDOWN
VREF SWITCHING
SS TIMER OVPCOMP PWM
CONTROL
PROTECTION SOFT
START UVLO
SCP6 UVLO
TIMER VINREG VOUT
30 MODE 4
VO3SEL VINREG 2
11 LDO 31
REGOUT
22
SCP CE
VDD CHIP GND
TIMER 10 IC9180 3
ENABLE 5
VREGD2IN (SYSTEM IC)
VREGD2 28
HVREG
25
IC6001 23
CPLUS
(VENUS ENGINE) CTL SEQ3 CP SW
PW D3.15V 13 SCPLDO VBAT RL9133
TIMER CP 2
CTL SEQ2
14 ON/OFF DRIVER VREGD VBAT (IS PWR ON2)
3 PIOB7 E8
CTL SEQ1 LOGIC Q1271 Q1272
16 CMINUS
CP SW 24 6 5 4
CTL1234
17 3 4 1 6
(G I2C CK) SCL VCC
K2 18 SERIAL VREGA 1 QR1271 2
CD9111 2 5 5
SDA I/F OSC
19 GND
VREGD 20 (POWER CTL SW) CD1271
1 6 3 4
(G I2C DAT) POWERCTLSW L9 1 2 3
K3 12 21 26 29 27
SEQ RT VREGD2 VREGA VREGD PW -0.95V
CD1801
CD1002 PW HDMI5.0V
72
12.11. Power(3) Block Diagram
IC1091
PW UNREG (SYNCHRONOUS STEP-DOWN CONVERTER)
VIN
9 BOOT
VIN 8
QR1001 10 OVER CURRENT PW D1.0V A
PVCC
PROTECTION
IC6001
(VENUS ENGINE) 4 3 UGATE CD1091
IC6506 UNDER & OVER
(LOAD SW) SWITCH SW
5 2 VOLTAGE DRIVER 6 PW D1.0V B
CONTROLLER
PROTECTION SW
1 VOUT VIN 4 PW D1.2V 7
LGATE
6 1 PGND
RIPPLE T1
A24 2 GND CE 3 PVCC
(PW DRAM1.2V A) GEN. SW PGOOD
5
AG4 2 A 0.9 VREF
+--
+-
SS
IC6503 4
(REGULATOR) VREGA FB
A3 (From IC1001-29) FB PGOOD
(PW DRAM1.2V) ON-TIME COMPARATOR
COMPARATOR FB
1 VOUT VCC 4
EN 2
G7 IC6504 1 EN
(LOAD SW) 2 GND CE 3
4 VOUT GND 1
IC1031
(DC/DC CONVERTER)
PW D1.8V 3 VIN CE 2
VIN
2 PG
8
IC6502
(REGULATOR) PG
SOFT THERMAL CONT.
C26 UVLO
(PW DRAM1.8V) START SHTDWN
1 VOUT VCC 4
AE2 HS
2 GND CE 3 COMP. LIM
CONT. CD1031
EN LOGIC LX
PW D3.5V 3 7 PW BIS5.2V
GATE
POWER DRIVE
IC6505 CONT.
(LOAD SW) PGND
1
COMP.
1 VOUT VIN 4 PW D1.0V B DIRECT CONT. & LS
COMPENSATION LIM
VOS
2 GND CE 3 ERROR 6
AGND AMP
4 TIMER
-
+ tON
IC6501 COMP. FB
(REGULATOR) 5
C1
(PW DRAM1.0V) CD1051
1 VOUT VCC 4
H5
PW SHUT11.0V
2 GND CE 3
IC9180
(SYSTEM IC) IC1051 5 6 7 8
(REGULATOR)
Q1051
1 RC VDD 10
J10 BACKUP CTL5 RL9135
2 SS BP 9 4 3 2 1
(BACKUP CTL4)
BACKUP CTL4 K11
3 DIS/EN GDRV 8
J7 POWERONH
4 COMP ISNS 7
RL9136
5 FB GND 6
(BACKUP CTL3)
(BACKUP CTL1)
BACKUP CTL3 J9 QR6501
M8 K9 BACKUP CTL1
3 EN VSS 2
IC1621
(REGULATOR) CD1621
73
FP4403
6 LPSW
LPSW
D GND
WIFI CLK
WIFI CMD
5 LPSW
WIFI DAT2
WIFI DAT1
PW D3R5V
EXMIC GND
EXMIC GND
WIFI RESET
PW MIC3R8V
EXT MIC DET
REMOTE ZOOM
9
7
5
3
1
11
25
2 GND
1 GND
WIFI ANT
WIFI ANT
WIFI ANT
WIFI ANT
FP4402
JACK P.C.B.
FP4401
STEREO
WIFI
1
2
3
4
Wi-Fi FPC
D GND
D GND
D GND
MICROPHONE
WIFI DAT3 8
DAT0 6
4
2
29 EXMIC GND 28
27 PW MIC3R8V 26
GUN DET 24
23 EXT MIC RINA 22
21 MIC AMP BIAS 20
19 REMOTE REC 18
17 AV KEY DET 16
15 PW D3R15V 14
13 PW D3R5V 12
10
(COMPONENT SIDE)
: (FOIL SIDE)
13.1. Interconnection Diagram
28 (N.C.) 29 (N.C.)
9
7
5
3
1
27 LCD EVF SEL
11
29
27
25
23
21
19
17
15
13
26 D GND
24 DRIVE DIAL 25 D GND
22 INT STB DET 23 D GND
JACK FPC
21 MIC GND
FLASH DET FPC
20 ECM RIN
18 MIC GND 19 ECM LIN
FP9901 17 (N.C.)
LPSW
D3R5V
D GND
D GND
D GND
16 (N.C.)
D3R15V
GUN DET
WIFI DAT3
WIFI DAT0
1 PI 1C E 15 (N.C.)
EXMIC GND
14
AV KEY DET
STX
PW MIC3R8V
REMOTE REC
FP9007
12 STX
3 PI 1C A/C 11 (N.C.)
8
6
4
2
10 (N.C.)
13 Wiring Connection Diagram
28
26
24
22
20
18
16
14
12
10
4 MOT 1B
FP9009
8 TTL 9 (N.C.)
5 MOT 1B 7 RXD
6 TXD
HOT SHOE FPC
6 MOT 1A
4 D GND 5 EYE SDA
7 MOT 1A
8 MOT 2A 2 EYE SCL 3 D3R15V
9 MOT 2A 1 EYE LEDA
LPSW
D GND
D3R5V
WIFI CLK
WIFI CMD
WIFI DAT2
WIFI DAT1
10 MOT 2B
EXMIC GND
WIFI RESET
PW MIC3R8V
EXT MIC DET
REMOTE ZOOM
HOT SHOE
61 GND
12 PI 2C A/C 60 VCCP O
13 PI 2C E 59 VDD2(10V)
58 GND
14 PI 2C K 57 GND
56 GND(Vcath)
15 SHUT THERMO 55 GND
54 VDD1(1.8V)
16 THERMO GND 53 MCLK
52 XHD
51 XVD
50 XCLR
49 NC
48 NC
47 NC
46 NC
45 NC
44 NC
43 NC
42 NC
41 DB7(Y7)
40 DB6(Y6)
39 DB5(Y5)
38 DB4(Y4)
37 DB3(Y3)
36 DB2(Y2)
35 DB1(Y1)
34 DB0(Y0)
33 VDD1(1.8V)
32 GND
31 DB15(Cb7/Cr7)
FP9302
30 DB14(Cb6/Cr6)
29 DB13(Cb5/Cr5)
28 DB12(Cb4/Cr4)
27 DB11(Cb3/Cr3)
26 DB10(Cb2/Cr2)
25 DB9(Cb1/Cr1)
LVF MODULE
24 DB8(Cb0/Cr0)
23 GND (XSCAN MODE)
22 TEN (WR PROTECT)
21 GND (PSCNT)
20 XCS
19 XSCK
18 SI
17 SO
16 DDEN (NC)
15 GND (TEST)
SLLK FPC
14 GND
13 VDD1(1.8V)
SHUTTER FPC
12 VCAL
SSWF FPC
11 R IB (NC)
10 AOUT (NC)
9 VGAM255
8 VGAM0
7 VOFS
6 GND (Vcath)
5 GND
4 GND
FP9003 3 VDD2(10V)
2 VCCP I
1 GND
1 SHUTTER1
(SLLK)
(SHUTTER)
(SSWF)
2 VG DET
ISP FPC
YHI-
13 UNREG
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
YHO-
X2HI-
IS CS
YDR+
SSWF
X2DR-
X2HO-
14 UNREG
IS PSV
D3R5V
D3R5V
VDD12
X1DR+
IS SCK
X1HO+
VDDDM
D3R15V
SD0CAP
SD0CBM
15 UNREG
SD0DB0P
SD0DB2P
SD0DB3P
SD0DA1P
SD0DB1M
SD0DA3M
SD0DA2M
SD0DA0M
16 UNREG
IS PWR ON3
17 (N.C.)
18 P-GND
19 P-GND
UNIT
20 P-GND
IS P.C.B.
2
4
6
8
2
4
6
8
21 P-GND
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
BG FPC
22 P-GND
LENS UNIT
23 P-GND
74
24 P-GND
FP3502
FP3501
MOUNT BASE
25 P-GND
LENS CAPACITOR
26 (N.C.)
27 BIAS1
ISS FPC
28 BATT2 AD
29 CMD DIAL VF1
30 DIAL VG CTL
31 CMD DIAL VF0
HD
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
32 PW D3R5V
YDR-
X1HI-
YHO+
X1DR-
X1HO-
D5R2V
D3R5V
VDD12
X2DR+
X2HO+
IS SDO
SD0CBP
SD0CAM
34
SD0DB1P
SD0DA3P
SD0DA2P
SD0DA0P
IS THERMO
35 VG ON DET
IS PWR ON2
CLK27 IS FCK
1
3
5
7
9
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
(LENS CONTACT)
1 LCD OPEN H
2 PW D3R15V
3 LCD ROTATE1
4 LCD-EVF SW
5 GND
6 GND
7 PW D3R15V
8 PW D3R15V
9 NC
10 NC
11 PW UNREG SYS
12 PW UNREG SYS
LENS FPC
13 NC
14 LCD BLT
15 VSYNC
16 HSYNC
17 GND
18 PCLK
19 GND
20 DB7(Y7)
21 DB6(Y6)
22 DB5(Y5)
23 DB4(Y4)
24 DB3(Y3)
25 DB2(Y2)
FP9301
1
3
5
7
9
26 DB1(Y1)
11
13
15
17
19
21
27 DB0(Y0)
28 DB15(Cb7/Cr7)
29 DB14(Cb6/Cr6)
30 DB13(Cb5/Cr5)
31 DB12(CB4/Cr4)
32 DB11(Cb3/Cr3)
BATTERY
33 DB10(Cb2/Cr2)
FP9002 34 DB9(Cb1/Cr1)
35 DB8(Cb0/Cr0)
GND
GND
GND
GND
LSCK
36 GND
LSL2B
LSLDP
LSRST
30 31 POWER ON L
LSDIO
17 D GND
LSB2L
GND
LSB2A
LSDET
RL8504
1 REAR DK
2
4
6
8
27 UNREG
10
12
16
18
22
24
28 UNREG
30 UNREG 29 UNREG
31 UNREG 32 UNREG 33 UNREG
32 UNREG
33 UNREG 30 UNREG 31 UNREG
28 UNREG 29 UNREG
26 UNREG 27 UNREG
25 NC
ACC GND
24 UNREG GND
GYRO REF
S ACC SCK
GYRO GND
GYRO GND
S GYRO CS
S ACC MISO
S GYRO SCK
23 UNREG GND
S GYRO MISO
S GYRO MOSI
22 WIFI RESET
20 PW DGYRO VDDI
14 PW DGYRO VDDM
TOP OPERATION FPC
18 THERMO
15
17
19
23
25
13 BACK BAT+
FLASH
12 D GND
10 D3R5V 11 D3R5V
REAR OPERATION FPC
8 D GND 9 D GND
(FOIL SIDE)
MAIN P.C.B.
6 7 NC
S ACC CS
NC
S ACC IRQ
GYRO OUT
GYRO GND
S GYRO CS
S ACC MOSI
S GYRO SCK
5
PW ACC VDD
STB UNREG
S GYRO MISO
S GYRO MOSI
4 STB UNREG
11 PW AGYRO VDD
13 PW DGYRO VDDI
21 PW DGYRO VDDM
1 STB UNREG
:
LCD UNIT
FLASH P.C.B.
(COMPONENT SIDE)
MR3 SW FPC
LCD
GYRO FPC
HINGE FPC
LCD IF P.C.B.
MR1 SW FPC
SPEAKER
75
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Schematic
Diagram Note
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List Note
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Power (P) (Main
P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Power Supply
(PS) (Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Jack (J) (Main
P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Accelerator (AC)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K BIS/Image
Sensor Connection (CC/CI) (Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Digital (D) (Main
P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K DRAM Power
(DP) (Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Hot Shoe (HS)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Main Connection
(MC) (Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Syscon (SY)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K SD card (SD)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Display (DI)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K SSWF (SS) (Main
P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Shutter Drive
(MS) (Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K BIS Drive (BI)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Gyro AMP (GA)
(Main P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Flash P.C.B.
(Flash P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Jack P.C.B. (Jack
P.C.B.)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Main P.C.B.
(Component Side)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Main P.C.B. (Foil
Side)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Flash P.C.B.
(Component Side)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Flash P.C.B. (Foil
Side)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Jack P.C.B.
(Component Side)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Jack P.C.B. (Foil
Side)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
C8502 F1K2J223A029 CAPACITOR 1
C8503 F1K2J223A029 CAPACITOR 1
C8504 F1G1H270A557 CAPACITOR 1
C8505 F1G0J1050007 CAPACITOR 1
C8506 F1J1A106A043 CAPACITOR 1
D1001 DB2J20800L DIODE 1 E.S.D.
D1051 B0JCRD000017 DIODE 1 E.S.D.
D1271 DB3S308F0L DIODE 1 E.S.D.
D1601 B0JCMD000066 DIODE 1 E.S.D.
D1901 B0JCPE000038 DIODE 1 E.S.D.
D1902 B0JCPE000038 DIODE 1 E.S.D.
D2001 DB2S31100L DIODE 1 E.S.D.
D8001 DZ2J082M0L DIODE 1 E.S.D.
D8002 B2ABAP000007 DIODE 1 E.S.D.
D8501 B0ECGP000006 DIODE 1 E.S.D.
D8502 DA2SF650EL DIODE 1 E.S.D.
D9001 DZ5S068D0R DIODE 1 E.S.D.
D9002 DZ5S068D0R DIODE 1 E.S.D.
D9003 B0JCCD000003 DIODE 1 E.S.D.
D9101 B0JCCD000003 DIODE 1 E.S.D.
ET2001 K4ZZ01000300 TERMINAL 1
FL2001 EXC28CH900U CHOKE COIL 1
FL2002 EXC28CH900U CHOKE COIL 1
FP3501 K1MY39BA0556 CONNECTOR 1
FP3502 K1MY41BA0647 CONNECTOR 1
FP4401 K1MY29BA0556 CONNECTOR 1
FP4402 K1MY04BA0636 CONNECTOR 1
FP4403 K1MY06BA0557 CONNECTOR 1
FP8501 K1MY33BA0723 CONNECTOR 1
FP9001 K1MY33BA0667 CONNECTOR 1
FP9002 K1MY19BA0556 CONNECTOR 1
FP9003 K1MY35BA0556 CONNECTOR 1
FP9004 K1MY33BA0667 CONNECTOR 1
FP9005 K1MY25BA0556 CONNECTOR 1
FP9006 K1MY21BA0723 CONNECTOR 1
FP9007 K1MY29BA0556 CONNECTOR 1
FP9009 K1MY29BA0556 CONNECTOR 1
FP9301 K1MY45BA0667 CONNECTOR 1
FP9302 K1MY61AA0288 CONNECTOR 1
FP9901 K1MY16BA0641 CONNECTOR 1
IC1001 C1ZBZ0004906 IC 1 E.S.D.
IC1031 C0DBAYY01798 IC 1 E.S.D.
IC1051 C0DBAYY02125 IC 1 E.S.D.
IC1091 C0DBAYY02385 IC 1 E.S.D.
IC1231 C0DBGYY03614 IC 1 E.S.D.
IC1251 C0DBAYY01533 IC 1 E.S.D.
IC1411 C0DBGYY03640 IC 1 E.S.D.
IC1431 C0DBGYY03614 IC 1 E.S.D.
IC1451 C0DBGYY03644 IC 1 E.S.D.
IC1471 C0DBGYY03614 IC 1 E.S.D.
IC1491 C0DBGYY03644 IC 1 E.S.D.
IC1611 C0DBGYY03650 IC 1 E.S.D.
IC1621 C0DBGYY03640 IC 1 E.S.D.
IC1901 C0JBAA000393 IC 1 E.S.D.
IC1902 C0JBAA000393 IC 1 E.S.D.
IC2701 VUEALLPT053 IC 1 E.S.D. [INBD]
IC5001 SUBF000023 IC 1 E.S.D. [INBD]
IC5101 C0ABGA000035 IC 1 E.S.D.
IC6001 VSG1033 IC 1 E.S.D.
IC6003 RS10933 IC 1 E.S.D.
IC6004 C0JBAS000182 IC 1 E.S.D.
IC6005 C0JBAS000182 IC 1 E.S.D.
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
IC6501 C0DBGYY05582 IC 1 E.S.D.
IC6502 C0DBGYY05590 IC 1 E.S.D.
IC6503 C0DBGYY05584 IC 1 E.S.D.
IC6504 C0ZBZ0002095 IC 1 E.S.D.
IC6505 C0ZBZ0002264 IC 1 E.S.D.
IC6506 C0ZBZ0002264 IC 1 E.S.D.
IC8501 C0ZBZ0001817 IC 1 E.S.D.
IC9103 C0DBGYY02368 IC 1 E.S.D.
IC9113 C0DBGYY02176 IC 1 E.S.D.
IC9133 C0JBAT000006 IC 1 E.S.D.
IC9134 C0JBAF000813 IC 1 E.S.D.
IC9162 C0JBAF000813 IC 1 E.S.D.
IC9180 C1AB00004163 IC 1 E.S.D.
IC9201 C0JBAS000429 IC 1 E.S.D.
IC9202 C0DBGYY00779 IC 1 E.S.D.
IC9203 C0DBGYY00779 IC 1 E.S.D.
IC9301 C0DBAYY02115 IC 1 E.S.D.
IC9901 C0GBY0000274 IC 1 E.S.D.
IP1002 ERBRD0R50X FUSE 1
IP1901 ERBRD1R50X FUSE 1
IP8501 ERBRD2R50X FUSE 1
IP9301 K5H1512A0024 FUSE 1
JK2002 K1FY119E0057 CONNECTOR 1
JK2003 K1FY105E0014 CONNECTOR 1
JK4401 K2HC106E0009 JACK 1
JK4402 K2HD104D0002 JACK 1
L1031 G1C3R3MA0477 CHIP INDUCTOR 1
L1051 G1C1R5MA0909 CHIP INDUCTOR 1
L1091 G1C1R5MA0943 CHIP INDUCTOR 1
L1101 G1C100MA0461 CHIP INDUCTOR 1
L1201 G1C150MA0477 CHIP INDUCTOR 1
L1251 G1C3R3MA0477 CHIP INDUCTOR 1
L1301 G1C100MA0461 CHIP INDUCTOR 1
L1401 G1C150MA0477 CHIP INDUCTOR 1
L1601 G1C4R7MA0477 CHIP INDUCTOR 1
L1701 G1C4R7MA0450 CHIP INDUCTOR 1
L2001 EXC24CE900U CHOKE COIL 1
L3501 G1C4R7MA0391 CHIP INDUCTOR 1
L3502 G1C4R7MA0391 CHIP INDUCTOR 1
L6101 G1C2R2KA0096 CHIP INDUCTOR 1
L9201 G1C1R0MA0172 CHIP INDUCTOR 1
L9301 G1C100MA0392 CHIP INDUCTOR 1
LB6002 J0JCC0000408 FILTER 1
LB6101 J0JFC0000006 FILTER 1
P8501 K4ZZ04000059 TERMINAL 1
P9201 K1NA17E00002 CONNECTOR 1
Q1051 B1CFRD000100 TRANSISTOR 1 E.S.D.
Q1271 B1HDCFA00031 TRANSISTOR 1 E.S.D.
Q1272 B1HFCFA00050 TRANSISTOR 1 E.S.D.
Q1901 FK3503010L TRANSISTOR 1 E.S.D.
Q1902 B1CHPB000008 TRANSISTOR 1 E.S.D.
Q1905 B1CHPB000008 TRANSISTOR 1 E.S.D.
Q1906 B1CHPB000008 TRANSISTOR 1 E.S.D.
Q1907 FK3503010L TRANSISTOR 1 E.S.D.
Q1908 FK3503010L TRANSISTOR 1 E.S.D.
Q2001 B1CFGD000003 TRANSISTOR 1 E.S.D.
Q2002 B1CFJD000007 TRANSISTOR 1 E.S.D.
Q3501 B1CFQC000018 TRANSISTOR 1 E.S.D.
Q5001 B1ABCF000302 TRANSISTOR 1 E.S.D.
Q8001 FK3503010L TRANSISTOR 1 E.S.D.
Q8501 B1JBLP000037 TRANSISTOR 1 E.S.D.
Q9002 B1HFCFA00050 TRANSISTOR 1 E.S.D.
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
Q9003 B1HFCFA00050 TRANSISTOR 1 E.S.D.
Q9041 B1HFCFA00050 TRANSISTOR 1 E.S.D.
Q9101 B1ABDF000017 TRANSISTOR 1 E.S.D.
Q9201 B1CHMB000007 TRANSISTOR 1 E.S.D.
Q9301 B1CHMB000007 TRANSISTOR 1 E.S.D.
Q9801 B1MBCGA00004 TRANSISTOR 1 E.S.D.
QR1001 B1GKCFJJ0012 TRANSISTOR 1 E.S.D.
QR1271 B1GKCFGN0001 TRANSISTOR 1 E.S.D.
QR1901 B1GBCFYY0219 TRANSISTOR 1 E.S.D.
QR1902 B1GBCFYY0219 TRANSISTOR 1 E.S.D.
QR2001 B1GKCFYY0029 TRANSISTOR 1 E.S.D.
QR3501 B1GBCFNN0015 TRANSISTOR 1 E.S.D.
QR6501 B1GBCFYY0217 TRANSISTOR 1 E.S.D.
QR8002 B1GFCFYY0021 TRANSISTOR 1 E.S.D.
QR8003 B1GFCFYY0021 TRANSISTOR 1 E.S.D.
QR9201 B1GBCFYY0217 TRANSISTOR 1 E.S.D.
QR9202 B1GDCFYY0150 TRANSISTOR 1 E.S.D.
QR9203 B1GBCFYY0217 TRANSISTOR 1 E.S.D.
QR9301 B1GBCFYY0217 TRANSISTOR 1 E.S.D.
QR9302 B1GFCFLL0009 TRANSISTOR 1 E.S.D.
R8501 D0GF472JA048 RESISTOR 1
R8502 D0GF104JA048 RESISTOR 1
R8503 D0GD393JA052 RESISTOR 1
R8504 D0GD363JA052 RESISTOR 1
R8505 D0GB104JA065 RESISTOR 1
R8506 D0GB680JA065 RESISTOR 1
R8507 D1BD4703A119 RESISTOR 1
R8508 ERJ2RHD1621X RESISTOR 1
R8509 D0GA473JA023 RESISTOR 1
R8510 D0GBR00J0004 RESISTOR 1
R8514 D0GAR00J0005 RESISTOR 1
RX6001 D1H81034A042 RESISTOR NETWORK 1
RX6002 D1H81034A042 RESISTOR NETWORK 1
RX6003 D1H81034A042 RESISTOR NETWORK 1
RX9001 D1H81014A042 RESISTOR NETWORK 1
RX9002 D1H81014A042 RESISTOR NETWORK 1
RX9005 D1H81044A042 RESISTOR NETWORK 1
RX9006 D1H82224A042 RESISTOR NETWORK 1
RX9007 D1H83924A042 RESISTOR NETWORK 1
RX9010 D1H84734A042 RESISTOR NETWORK 1
RX9201 D1H81034A042 RESISTOR NETWORK 1
RX9301 D1H81014A042 RESISTOR NETWORK 1
RX9302 D1H81014A042 RESISTOR NETWORK 1
RX9303 D1H81014A042 RESISTOR NETWORK 1
RX9304 D1H81014A042 RESISTOR NETWORK 1
T8501 G5DYA0000152 SWITCHING TRANS 1
T9801 G5DYZ0000028 SWITCHING TRANS 1
TH6001 D4CC11030013 NON‐LINEAR RESISTOR 1
VA9003 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9004 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9005 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9007 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9008 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9009 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9010 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9011 D4ED18R00008 NON‐LINEAR RESISTOR 1
VA9012 D4ED18R00008 NON‐LINEAR RESISTOR 1
X6001 H0J480500063 CRYSTAL RESONATOR 1
X9101 H0J327200230 CRYSTAL RESONATOR 1
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Frame and
Casing Section
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Camera Lens
Section (1) (HFS12060)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Camera Lens
Section (2) (HFS14140)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Camera Lens
Section (3) (HFS1442A)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Packing Parts
and Accessories Section (1) (G80/81/85)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Packing Parts
and Accessories Section (2) (G80M/81M/85M)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Packing Parts
and Accessories Section (3) (G80H/81H/85H)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Packing Parts
and Accessories Section (4) (G85K)
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
(RTL)E.S.D. G80EG,G80EC,G80EF,G80
EB,G81EG,G80MEG,G80MEC,G80MEF,G80
1 SEP0848AB MAIN P.C.B. 1
MEB,G81MEG,G80HEG,G80HEC,G80HEF,G
81HEG
(RTL)E.S.D. G80EE,G85P,G85PP,G85G
C,G85GH,G85GK,G85GN,G85GD,G80MEE,
1 SEP0848AA MAIN P.C.B. 1
G85MP,G85MPP,G85MGN,G85HGH,G85KGC
,G85KGN
2 SEP0850AA FLASH P.C.B. 1 (RTL)E.S.D.
3 SEP0851AA JACK P.C.B. 1 E.S.D.
4 DVWL1001Z MAIN‐FLASH FPC 1
5 F2A2F6000011 E.CAPACITOR 1 (C8501)
6 F2A2F6000011 E.CAPACITOR 1 (C8507)
7 ML‐421S/DB BUTTON BATTERY 1 (B8501)
8 SMB0225 CAPACITOR EARTH SPRING 1
9 SMB0225 CAPACITOR EARTH SPRING 1
10 5GE1MC361Z FRONT CASE UNIT 1
10‐1 2GE1MC361Z TRIPOD UNIT 1
10‐2 SYQ0876 BG CONTACT FPC UNIT 1
10‐3 SMQ1043 BG SHADING PIECE 1
11 SXQ0673 BIS UNIT 1
12 SEQ0138 LENS CONNECTOR 1
13 SMB0206 ADJUST SPRING 1
14 SMB0206 ADJUST SPRING 1
15 SMB0206 ADJUST SPRING 1
16 SMG0100 DAMPER O RING 1
17 SXQ0635‐SA SHUTTER UNIT 1
18 VMC2063 MOUNT SPRING 1
19 VMD6702 MOUNT 1
20 VMG2060 MOUNT RING 1
21 1GE1MC361Z JACK HOLDER UNIT 1
22 DVMC1008Z GASKET 1
23 STJ0200 JACK FPC 1
24 SEP0856AA MR1 SW FPC 1 E.S.D.
25 6GE1MC361Z REAR CASE UNIT 1
25‐1 SMP0307 EYE CUP PLATE 1
26 SYK1631 LCD UNIT 1
27 SYQ0870 REAR PLATE UNIT 1
28 VGQ1F77‐A HINGE FIX COVER 1
29 L0AA01A00181 SPEAKER 1
30 SGQ0790 LCD LOCK PIECE 1
31 SGU0220 DISPLAY BUTTON 1
32 SGU0225 MENU BUTTON 1
33 SGU0240 DELETE BUTTON 1
34 SGU0241 CURSOR BUTTON A 1
35 SGU0242 CURSOR BUTTON B 1
36 SGU0243 CURSOR BUTTON C 1
37 SGU0244 CURSOR BUTTON D 1
38 SGU0271 FN2 BUTTON 1
39 SGU0272 PLAY BUTTON 1
40 SKK0429K HINGE ARM COVER BOTTOM 1
41 SKK0430K HINGE ARM COVER TOP 1
42 SMC0091 HINGE EARTH PLATE 1
43 SMG0101 CURSOR BUTTON PACKING 1
44 SMP0309 LCD LOCK HOLDER 1
45 SMP0367 SENSOR EARTH PLATE 1
46 VGQ0T64‐A FPC SHEET 1
47 VGQ1F95 HINGE CUSHION 4 1
48 VGQ1J71 HEAT RADIATION SHEET C 1
49 VMB4373 LCD LOCK SPRING 1
50 VMT2075 HEAT RADIATION PAD 1
51 3GE1MC361Z BATTERY FRAME UNIT 1
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
52 SYF0094 BATTERY DOOR UNIT 1
53 SMB0242 BATTERY DOOR SPRING 1
54 SMP0364 BATTERY LOCK HOLDER 1
55 SMS0294 BATTERY DOOR SHAFT 1
56 VGU0M81 BATTERY LOCK KNOB 1
57 VMB4407 BATTERY LOCK SPRING 1
58 VMB4409 BATTERY OUT SPRING 1
59 4GE1MC361Z TOP CASE UNIT 1
59‐1 SYQ0873 STRAP R UNIT 1
59‐2 VMC2111 SHOE SPRING 1
60 SYQ0878 LVF UNIT 1
61 SYQ0865 REAR GRIP UNIT 1
62 SYQ0866 EYE CUP UNIT 1
63 DVYE1002Z FRONT GRIP L 1
64 DVYE1003Z FRONT GRIP R 1
67 SKK0431K FLASH CASE TOP 1
68 SMG0112 FLASH CASE PACKING 1
69 SMP0322 MAIN HEAT SINK 1
70 SMQ1049 BATTERY CONNECT COVER 1
71 VGQ1U14 GASKET 1
72 SMT0188 FRONT WP PORON A 1
B1 VHD1681 SCREW 1
B2 VHD1681 SCREW 1
B3 VHD1681 SCREW 1
B4 VHD1681 SCREW 1
B7 XQN16+BJ5FN SCREW 1
B8 XQN16+BJ5FN SCREW 1
B9 XQN16+BJ5FN SCREW 1
B10 VHD1681 SCREW 1
B11 VHD1681 SCREW 1
B12 XQN16+BJ5FN SCREW 1
B13 XQN16+BJ5FN SCREW 1
B14 SHD0015 SCREW 1
B15 XQN16+BJ7FN SCREW 1
B16 VHD2179 SCREW 1
B17 XQN16+BJ5FN SCREW 1
B18 XQN16+BJ4FN SCREW 1
B19 XQN16+BJ4FN SCREW 1
B20 VHD2251‐B SCREW 1
B21 VHD2251‐B SCREW 1
B22 VHD2179 SCREW 1
B23 VHD2438 SCREW 1
B24 VHD2461 SCREW 1
B25 DVHD1002Z SCREW 1
B26 XQN16+BJ5FN SCREW 1
B27 VHD2179 SCREW 1
B28 VHD2438 SCREW 1
B29 VHD2438 SCREW 1
B30 VHD2438 SCREW 1
B31 VHD2438 SCREW 1
B32 VHD2471 SCREW 1
B33 VHD2179 SCREW 1
B34 VHD2462 SCREW 1
B35 VHD2462 SCREW 1
B36 XQN14+BJ4FJK SCREW 1
B37 XQN14+BJ4FJK SCREW 1
B38 SHD0061 SCREW 1
B39 SHD0061 SCREW 1
B40 SHD0061 SCREW 1
B41 VHD2306 SCREW 1
B42 VHD2306 SCREW 1
B43 VHD2190 SCREW 1
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
B44 VHD2124 SCREW 1
B45 VHD2190 SCREW 1
B46 VHD2124 SCREW 1
B47 VHD2384 SCREW 1
B48 XQN16+BJ5FN SCREW 1
B49 VHD2335 SCREW 1
B50 SHD0118 SCREW 1
B51 SHD0118 SCREW 1
B52 SHD0108 SCREW 1
B53 SHD0108 SCREW 1
B54 SHD0108 SCREW 1
B55 VHD2200‐B SCREW 1
B56 VHD2200‐B SCREW 1
B57 VHD2247‐A SCREW 1
B58 XQN16+BJ6FJK SCREW 1
B59 VHD2515 SCREW 1
B60 VHD2515 SCREW 1
B61 VHD2515 SCREW 1
B62 VHD2515 SCREW 1
B63 VHD2515 SCREW 1
B64 VHD2515 SCREW 1
B65 XQN16+BJ6FJK SCREW 1
B66 XQN16+BJ6FJK SCREW 1
B67 XQN16+BJ6FJK SCREW 1
B68 XQN16+BJ6FJK SCREW 1
B69 XQN16+BJ4FN SCREW 1
B70 XQN16+BJ4FN SCREW 1
B71 XQN16+BJ5FN SCREW 1
B72 XQN16+BJ4FN SCREW 1
B73 XQN16+BJ4FN SCREW 1
B74 XQN16+BJ4FN SCREW 1
B75 XQN16+BJ4FN SCREW 1
200 SXW0282 LENS UNIT 1 G80M,G81M,G85M
201 SDW0373K DECORATION RING 1 G80M,G81M,G85M
202 SDW0372K FILTER RING 1 G80M,G81M,G85M
203 VMC2220 WAVE WASHER 1 G80M,G81M,G85M
204 SXQ0655 FRONT FRAME UNIT 1 G80M,G81M,G85M
205 SXQ0653 FOCUS RING UNIT 1 G80M,G81M,G85M
206 ‐‐‐‐‐ LENS MAIN UNIT 1 G80M,G81M,G85M(NOT SUPPLIED)
207 VMS8326 ZOOM PIN 1 G80M,G81M,G85M
208 VMG1855 FLOATING RUBBER 3 G80M,G81M,G85M
209 VMG1855 FLOATING RUBBER 3 G80M,G81M,G85M
210 VMG1855 FLOATING RUBBER 3 G80M,G81M,G85M
211 SEJ0005 MOUNT CONTAT UNIT 1 G80M,G81M,G85M
212 SXQ0648 REAR FRAME UNIT 1 G80M,G81M,G85M
213 VMS8278 ADJUST PIN 1 G80M,G81M,G85M
214 SMG0095‐M SEALING RUBBER 1 G80M,G81M,G85M
215 SXQ0649 L MOUNT UNIT 1 G80M,G81M,G85M
216 ‐‐‐‐‐ SHADING FRAME 1 G80M,G81M,G85M(NOT SUPPLIED)
B201 VHD2296 SCREW 1 G80M,G81M,G85M
B202 VHD2296 SCREW 1 G80M,G81M,G85M
B203 VHD2296 SCREW 1 G80M,G81M,G85M
B204 XQN16+BJ4FNK SCREW 1 G80M,G81M,G85M
B205 XQN16+BJ4FNK SCREW 1 G80M,G81M,G85M
B206 XQN16+BJ4FNK SCREW 1 G80M,G81M,G85M
B207 VHD2296 SCREW 1 G80M,G81M,G85M
B208 VHD2296 SCREW 1 G80M,G81M,G85M
B209 VHD2296 SCREW 1 G80M,G81M,G85M
B210 VHD2296 SCREW 1 G80M,G81M,G85M
B211 VHD2298 SCREW 1 G80M,G81M,G85M
B212 VHD2299 SCREW 3 G80M,G81M,G85M
B213 VHD2299 SCREW 1 G80M,G81M,G85M
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
B214 VHD2299 SCREW 1 G80M,G81M,G85M
B215 VHD2246 SCREW 1 G80M,G81M,G85M
B216 VHD2246 SCREW 1 G80M,G81M,G85M
300 SXW0205 LENS UNIT 1 G80H,G81H,G85H [INBD]
301 VDW2635 FILTER RING 1 G80H,G81H,G85H [INBD]
302 ‐‐‐ SHADING FRAME 1 G80H,G81H,G85H(NOT SUPPLIED )
303 VEJ2336 LENS MOUNT CONTAT UNIT 1 G80H,G81H,G85H [INBD]
304 VMG1855 FLOATING RUBBER 1 G80H,G81H,G85H [INBD]
305 VMG1855 FLOATING RUBBER 1 G80H,G81H,G85H [INBD]
306 VMG1855 FLOATING RUBBER 1 G80H,G81H,G85H [INBD]
307 VMG1855 FLOATING RUBBER 1 G80H,G81H,G85H [INBD]
308 SXQ0394 REAR FRAME UNIT 1 G80H,G81H,G85H [INBD]
309 ‐‐‐ LENS MAIN UNIT 1 G80H,G81H,G85H(NOT SUPPLIED )
310 VYC1120 DECORATION RING 1 G80H,G81H,G85H[INBD]
311 VMG2090 DUST PROOF RING 1 G80H,G81H,G85H [INBD]
312 K0ZZ00000641 OIS SWITCH 1 G80H,G81H,G85H [INBD]
313 VXQ2372 L MOUNT UNIT 1 G80H,G81H,G85H [INBD]
B300 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B301 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B302 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B303 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B304 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B305 VHD2296 SCREW 1 G80H,G81H,G85H [INBD]
B306 VHD2296 SCREW 1 G80H,G81H,G85H [INBD]
B307 VHD2296 SCREW 1 G80H,G81H,G85H [INBD]
B308 VHD2299 SCREW 1 G80H,G81H,G85H [INBD]
B309 VHD2299 SCREW 1 G80H,G81H,G85H [INBD]
B310 VHD2299 SCREW 1 G80H,G81H,G85H [INBD]
B311 VHD1868 SCREW 1 G80H,G81H,G85H [INBD]
B312 VHD2298 SCREW 1 G80H,G81H,G85H [INBD]
B313 VHD2246 SCREW 1 G80H,G81H,G85H [INBD]
B314 VHD2246 SCREW 1 G80H,G81H,G85H [INBD]
B315 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B316 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
B317 VHD2096 SCREW 1 G80H,G81H,G85H [INBD]
400 SXW0210 LENS UNIT 1 G85K
402 ‐‐‐‐‐ SHADING FRAME 1 G85K(NOT SUPPLIED)
403 VEJ2337 LENS MOUNT CONTAT UNIT 1 G85K [INBD]
404 VGH5356 DECORATION RING 1 G85K [INBD]
406 VDW2695 L MOUNT UNIT 1 G85K [INBD]
407 SYF0076 REAR FRAME UNIT 1 G85K [INBD]
408 ‐‐‐‐‐ LENS MAIN UNIT 1 G85K(NOT SUPPLIED)
B401 VHD2246 SCREW 1 G85K [INBD]
B402 VHD2246 SCREW 1 G85K [INBD]
B403 VHD2246 SCREW 1 G85K [INBD]
B404 VHD2296 SCREW 1 G85K [INBD]
B405 VHD2296 SCREW 1 G85K [INBD]
B406 VHD2296 SCREW 1 G85K [INBD]
B407 VHD2296 SCREW 1 G85K [INBD]
B408 VHD2299 SCREW 1 G85K [INBD]
B409 VHD2299 SCREW 1 G85K [INBD]
B410 VHD2299 SCREW 1 G85K [INBD]
B413 VHD2298 SCREW 1 G85K [INBD]
B414 VHD1868 SCREW 1 G85K [INBD]
B420 VHD2496 SCREW 1 G85K[INBD]
B421 VHD2496 SCREW 1 G85K[INBD]
B422 VHD2496 SCREW 1 G85K[INBD]
500 VPF1316A CAMERA BAG 1
501 SKF0106K HOT SHOE COVER 1
502 VKF4971 BODY CAP 1
503 SKF0145K BG CONTACT COVER 1
508 DVQX1003Z BASIC O/I (ENGLISH) 1 G85P,G85PP
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
508 DVQX1004Z BASIC O/I (SPANISH) 1 G85P,G85PP
508 DVQX1005Z BASIC O/I (FRENCH) 1 G85PP
508 DVQX1006Z BASIC O/I (GERMAN) 1 G80EG,G81EG
508 DVQX1007Z BASIC O/I (FRENCH) 1 G80EG,G80EF,G81EG
508 DVQX1008Z BASIC O/I (ITALIAN) 1 G80EG
508 DVQX1009Z BASIC O/I (DUTCH) 1 G80EG,G80EF
508 DVQX1010Z BASIC O/I (SPANISH) 1 G80EC
508 DVQX1011Z BASIC O/I (PORTUGUESE) 1 G80EC
508 DVQX1012Z BASIC O/I (SWEDISH) 1 G80EC
508 DVQX1013Z BASIC O/I (DANISH) 1 G80EC
508 DVQX1014Z BASIC O/I (FINNISH) 1 G80EC
508 DVQX1015Z BASIC O/I (ENGLISH) 1 G80EB
508 DVQX1016Z BASIC O/I (RUSSIAN) 1 G80EE
508 DVQX1017Z BASIC O/I (UKRAINIAN) 1 G80EE
508 DVQX1018Z BASIC O/I (ENGLISH) 1 G85GC,G85GH
508 DVQX1019Z BASIC O/I (CHINESE(TRADITIONAL)) 1 G85GC,G85GH
508 DVQX1020Z BASIC O/I (ARABIC) 1 G85GC
508 DVQX1021Z BASIC O/I (CHINESE(SIMPLIFIED)) 1 G85GK
508 DVQX1022Z BASIC O/I (ENGLISH) 1 G85GN
508 DVQX1023Z BASIC O/I (KOREAN) 1 G85GD
509 VQL2J61 GD LABEL 1 G85GD
510 VPF1542 BAG, POLYETHYLENE 1
511 DVPW1001Z SHOULDER STRAP 1
512 DVPK1004Z PACKING CASE 1 G80EG,G80EC,G80EF,G80EB,G80EE
512 DVPK1005Z PACKING CASE 1 G81EG
G85P,G85PP,G85GC,G85GH,G85GN,G85G
512 DVPK1003Z PACKING CASE 1
D
512 DVPK1006Z PACKING CASE 1 G85GK
513 DVPN1003Z TRAY 1
514 SPN0280 PAD C 1
515 SPN0282 LENS PAD A 1 G80,G81,G85
G80EG,G80EC,G80EF,G80EB,G80EE,G81
520 DE‐A80AD/SX BATTERY CHARGE 1
EG,G85GN
520 DE‐A79BB/SX BATTERY CHARGE 1 G85P,G85PP
520 DE‐A80BE/SX BATTERY CHARGE 1 G85GC,G85GH,G85GK,G85GD
521 ‐‐‐‐‐ BATTERY PACK 1
522 K1HY04YY0106 USB CABLE W/PLUG 1
G80EG,G80EC,G80EF,G80EE,G81EG,G85
523 K2CQ2YY00082 AC CORD W/PLUG 1
GC
523 K2CT3YY00034 AC CORD W/PLUG 1 G80EB,G85GC,G85GH
523 K2CA2YY00130 AC CORD W/PLUG 1 G85GK
523 K2CJ2YY00052 AC CORD W/PLUG 1 G85GN
523 K2CR2YY00026 AC CORD W/PLUG 1 G85GD
600 VPF1316A CAMERA BAG 1
601 SKF0106K HOT SHOE COVER 1
602 VKF4971 BODY CAP 1
603 SKF0145K BG CONTACT COVER 1
608 DVQX1003Z BASIC O/I (ENGLISH) 1 G85MP,G85MPP
608 DVQX1004Z BASIC O/I (SPANISH) 1 G85MP,G85MPP
608 DVQX1005Z BASIC O/I (FRENCH) 1 G85MPP
608 DVQX1006Z BASIC O/I (GERMAN) 1 G80MEG,G81MEG
608 DVQX1007Z BASIC O/I (FRENCH) 1 G80MEG,G80MEF,G81MEG
608 DVQX1008Z BASIC O/I (ITALIAN) 1 G80MEG
608 DVQX1009Z BASIC O/I (DUTCH) 1 G80MEG,G80MEF
608 DVQX1010Z BASIC O/I (SPANISH) 1 G80MEC
608 DVQX1011Z BASIC O/I (PORTUGUESE) 1 G80MEC
608 DVQX1012Z BASIC O/I (SWEDISH) 1 G80MEC
608 DVQX1013Z BASIC O/I (DANISH) 1 G80MEC
608 DVQX1014Z BASIC O/I (FINNISH) 1 G80MEC
608 DVQX1015Z BASIC O/I (ENGLISH) 1 G80MEB
608 DVQX1016Z BASIC O/I (RUSSIAN) 1 G80MEE
608 DVQX1017Z BASIC O/I (UKRAINIAN) 1 G80MEE
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
608 DVQX1022Z BASIC O/I (ENGLISH) 1 G85MGN
610 VPF1542 BAG, POLYETHYLENE 1
611 DVPW1001Z SHOULDER STRAP 1
G80MEG,G80MEC,G80MEF,G80MEB,G80ME
612 DVPK1010Z PACKING CASE 1
E
612 DVPK1011Z PACKING CASE 1 G81MEG
612 DVPK1009Z PACKING CASE 1 G85MP,G85MPP,G85MGN
613 DVPN1003Z TRAY 1
614 SPN0280 PAD C 1
615 SPN0284 LENS PAD C 1 G80M,G81M,G85M
620 DE‐A79BB/SX BATTERY CHARGE 1 G85MP,G85MPP
G80MEG,G80MEC,G80MEF,G80MEB,G80ME
620 DE‐A80AD/SX BATTERY CHARGE 1
E,G81MEG,G85MGN
621 ‐‐‐‐‐ BATTERY PACK 1
622 K1HY04YY0106 USB CABLE W/PLUG 1
623 K2CJ2YY00052 AC CORD W/PLUG 1 G85MGN
G80MEG,G80MEC,G80MEF,G80MEE,G81ME
623 K2CQ2YY00082 AC CORD W/PLUG 1
G
623 K2CT3YY00034 AC CORD W/PLUG 1 G80MEB
628 VPF1475 LENS BAG 1 G80M,G81M,G85M
630 VYF3514 LENS CAP 1 G80M,G81M,G85M
631 VFC4605‐B LENS REAR CAP 1 G80M,G81M,G85M
632 SYA0066 LENS HOOD UNIT 1 G80M,G81M,G85M
700 VPF1316A CAMERA BAG
701 SKF0106K HOT SHOE COVER
702 VKF4971 BODY CAP
703 SKF0145K BG CONTACT COVER 1
708 DVQX1006Z BASIC O/I (GERMAN) 1 G80HEG,G81HEG
708 DVQX1007Z BASIC O/I (FRENCH) 1 G80HEG,G80HEF,G81HEG
708 DVQX1008Z BASIC O/I (ITALIAN) 1 G80HEG
708 DVQX1009Z BASIC O/I (DUTCH) 1 G80HEG,G80HEF
708 DVQX1010Z BASIC O/I (SPANISH) 1 G80HEC
708 DVQX1011Z BASIC O/I (PORTUGUESE) 1 G80HEC
708 DVQX1012Z BASIC O/I (SWEDISH) 1 G80HEC
708 DVQX1013Z BASIC O/I (DANISH) 1 G80HEC
708 DVQX1014Z BASIC O/I (FINNISH) 1 G80HEC
708 DVQX1018Z BASIC O/I (ENGLISH) 1 G85HGH
708 DVQX1019Z BASIC O/I (CHINESE(TRADITIONAL)) 1 G85HGH
710 VPF1542 BAG, POLYETHYLENE 1
711 DVPW1001Z SHOULDER STRAP 1
712 DVPK1012Z PACKING CASE 1 G80HEG,G80HEC,G80HEF
712 DVPK1016Z PACKING CASE 1 G81HEG
712 DVPK1013Z PACKING CASE 1 G85HGH
713 DVPN1003Z TRAY 1
714 SPN0280 PAD C 1
715 SPN0284 LENS PAD C 1 G80H,G81H,G85H
720 DE‐A80AD/SX BATTERY CHARGE 1 G80HEG,G80HEC,G80HEF,G81HEG
720 DE‐A80BE/SX BATTERY CHARGE 1 G85HGH
721 ‐‐‐‐‐ BATTERY PACK 1
722 K1HY04YY0106 USB CABLE W/PLUG 1
723 K2CQ2YY00082 AC CORD W/PLUG 1 G80HEG,G80HEC,G80HEF,G81HEG
723 K2CT3YY00034 AC CORD W/PLUG 1 G85HGH
728 VPF1509 LENS BAG 1 G80H,G81H,G85H
730 VYF3514 LENS CAP 1 G80H,G81H,G85H
731 VFC4605‐B LENS REAR CAP 1 G80H,G81H,G85H
732 VYC1119‐B LENS HOOD UNIT 1 G80H,G81H,G85H
800 VPF1316A CAMERA BAG 1
801 SKF0106K HOT SHOE COVER 1
802 VKF4971 BODY CAP 1
803 SKF0145K BG CONTACT COVER 1
808 DVQX1018Z BASIC O/I (ENGLISH) 1 G85KGC
808 DVQX1019Z BASIC O/I (CHINESE(TRADITIONAL)) 1 G85KGC
Model No. : DMCG80/G80M/G80H/G81/G81M/G81H/G85/G85M/G85H/G85K Parts List
Ref.
Change Safety Part No. Part Name & Description Q'ty Remarks
No.
808 DVQX1020Z BASIC O/I (ARABIC) 1 G85KGC
808 DVQX1022Z BASIC O/I (ENGLISH) 1 G85KGN
810 VPF1542 BAG, POLYETHYLENE 1
811 DVPW1001Z SHOULDER STRAP 1
812 DVPK1007Z PACKING CASE 1 G85KGC,G85KGN
813 DVPN1003Z TRAY 1
814 SPN0280 PAD C 1
815 SPN0284 LENS PAD C 1 G85K
820 DE‐A80AD/SX BATTERY CHARGE 1 G85KGN
820 DE‐A80BE/SX BATTERY CHARGE 1 G85KGC
821 ‐‐‐‐‐ BATTERY PACK 1
822 K1HY04YY0106 USB CABLE W/PLUG 1
823 K2CJ2YY00052 AC CORD W/PLUG 1 G85KGN
823 K2CQ2YY00082 AC CORD W/PLUG 1 G85KGC
823 K2CT3YY00034 AC CORD W/PLUG 1 G85KGC
828 VPF1484 LENS BAG 1 G85K
830 VYF3510 LENS CAP 1 G85K
831 VFC4605‐B LENS REAR CAP 1 G85K
832 VYC1113‐1B LENS HOOD UNIT 1 G85K