Professional Documents
Culture Documents
Steel connections
Detailed report
___________________________________________________________________________________________________________________________
___________________________________________________________________________________________________________________________
MEMBERS
Actual members
Right brace : Yes
Left brace : No
Column
General
Section : W 10X88
Material : A992 Gr50
Column orientation : Longitudinal
Longitudinal offset : 0 in
Include opposite stiffener : No
Right brace
General
Section : HSS_SQR 10X10X1_2
Material : A500 GrB rectangular
Brace slope angle (degrees) : 25
Brace long leg on gusset : Yes
Additional geometric data
wpx: WP horizontal displacement : 0 in
wpy: WP vertical displacement : 0 in
Le: Minimum distance to other members : 1 in
L1: Left distance : 3 in
L2: Right distance : 3 in
Page1
BASE PLATE
Base plate
Position on the support : Center
N: Longitudinal dimension : 55 in
B: Transversal dimension : 34 in
Thickness : 2 in
Material : A572 Gr50
Column weld : E70XX
Outer welds flanges only : No
D: Column weld size (1/16 in) : 5 REFER DESIGN DRAWING FOR BASE PLATE
Override A2/A1 ratio : No
DESIGN
Include shear lug : Yes
Shear lug
Orientation : Transversal direction
Consider same width as base plate : Yes
Depth : 5 in
Thickness : 2.5 in
Weld type : Fillet
Base plate weld : E70XX
Base plate weld size : 5
Consider friction : No
Support
With pedestal : No
Longitudinal dimension : 10 ft
Transversal dimension : 10 ft
Thickness : 50 in
Material : C 8-60
Include grouting : No
Anchor
Anchor position : Longitudinal position
Rows number per side : 1
Anchors per row : 4
Longitudinal edge distance on the plate : 2.5 in
Transverse edge distance on the plate : 2.5 in
Anchor type : Headed
Head type : Hexagonal
Include lock nut : Yes
Anchor : 7/8"
Effective embedment depth : 12 in
Total length : 15.943 in
Material : F1554 Gr36
Fy : 36 kip/in2
Fu : 58 kip/in2
Cracked concrete : No
Brittle steel : No
Anchors welded to base plate : No
Anchor reinforcement
Type of reinforcement : Primary
Tension reinforcement : No
Shear reinforcement : No
INTERFACES
Right brace - Gusset
General
tp: Thickness : 0.5 in
Material : A36
LV: Length on column : 19 in
LH: Length over plate : 14 in
Right brace - Gusset/Brace connection
General
Connection type : Welded
Lt: Length on toe : 10 in
Lh: Length on heel : 10 in
Brace weld : E70XX
D: Weld size (1/16 in) : 5
dp: Distance between weld and plate end : 1 in
Right brace - Gusset/Column connection
General
Connection type to column : Directly welded
Directly welded
Column weld : E70XX
Page2
D: Weld size to column (1/16 in) : 5
Right brace - Gusset/Base plate connection
Directly welded
Base plate weld : E70XX
D: Plate weld size (1/16 in) : 5
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Ratio 0.86
Brace
Yielding strength due to axial load [Kip] 712.08 225.00 DL1 0.32 Eq. J4-1
Tension rupture [Kip] 451.82 225.00 DL1 0.50 Eq. J4-2
Gusset
Tension yielding on the Whitmore section [Kip] 273.73 225.00 DL1 0.82 Eq. J4-1
Buckling on the Whitmore section [Kip] 340.66 225.00 DL 0.66 Eq. E3-1
Ratio 0.82
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Gusset
Beam yielding (normal stress) [Kip] 226.80 40.80 DL 0.18 Eq. B-1,
Appendix B,
DG29, Eq. J4-1
Shear yielding [Kip] 151.20 123.51 DL 0.82 Eq. J4-3
Gusset edge tension stress [Kip/in2] 32.40 4.25 DL 0.13 J4-1
Gusset edge shear stress [Kip/in2] 21.60 17.64 DL 0.82 J4-1
Weld capacity [Kip] 215.17 160.08 DL 0.74 Tables 8-4 .. 8-11
Page3
Ratio 0.82
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Gusset
Beam yielding (normal stress) [Kip] 307.80 166.98 DL 0.54 Eq. B-1,
Appendix B,
DG29, Eq. J4-1
Shear yielding [Kip] 205.20 65.31 DL 0.32 Eq. J4-3
Gusset edge tension stress [Kip/in2] 32.40 8.46 DL 0.26 J4-1
Gusset edge shear stress [Kip/in2] 21.60 6.87 DL 0.32 J4-1
Weld capacity [Kip] 387.93 220.17 DL 0.57 Tables 8-4 .. 8-11
Column
Web crippling [Kip] 1191.23 166.98 DL 0.14 Eq. J10-4,
Eq. B-1,
Appendix B,
DG29
Local web yielding [Kip] 800.11 166.98 DL 0.21 Eq. J10-2,
Eq. B-1,
Appendix B,
DG29
Ratio 0.57
Base plate
Distance from anchor to edge [in] 2.06 0.25 --
Weld size [1/16in] 5 4 -- table J2.4
Shear lug
Weld size [1/16in] 5 5 -- table J2.4
Right gusset
Weld size [1/16in] 5 3 -- table J2.4
Page4
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Concrete base
Axial bearing [Kip/in2] 8.84 0.06 DL 0.01 DG1 3.1.1;
Base plate
Flexural yielding (bearing interface) [Kip*ft/ft] 45.00 7.57 DL 0.17 DG1 Eq. 3.3.13,
DG1 Sec 3.1.2
Flexural yielding (tension interface) [Kip*ft/ft] 45.00 20.65 DL1 0.46 DG1 Eq. 3.3.13
Shear lug
Bearing on the concrete [Kip] 1149.20 203.92 DL 0.18 DG1 Sec 3.5.2
Shear on the concrete [Kip] 1564.35 203.92 DL 0.13 DG1 Sec 3.5.2,
DG1 p. 42
Flexural yielding [Kip*ft] 199.22 42.48 DL 0.21 DG1 p. 43,
DG1 Sec 3.5.2
Weld capacity [Kip/ft] 125.29 75.56 DL 0.60 p. 8-9,
Sec. J2.5,
Sec. J2.4,
DG1 Sec 3.5.2,
DG1 p. 43
Column
Weld capacity [Kip/ft] 125.29 8.03 DL1 0.06 p. 8-9,
Sec. J2.5,
Sec. J2.4,
DG1 p. 35
Ratio 0.60
Major axis
Anchors
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
Anchors
Anchor spacing [in] 16.67 3.50 -- Sec. D.8.1
Concrete cover [in] 34.56 3.00 -- Sec. 7.7.1
Effective length [in] 12.57 -- 49.43
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
Ratio 0.77
Ratio 0.77
REFER DESIGN DRAWING FOR
BASE PLATE DESIGN
Page5
Major axis
Maximum compression (DL)
--------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 60.24 [lb/in2]
Minimum bearing pressure 60.24 [lb/in2]
Maximum anchor tension 0.03 [kip]
Minimum anchor tension 0.00 [kip]
Neutral axis angle 0.00 [deg]
Bearing length 46.45 [in]
--------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[in] [in] [kip] [kip]
------------------------------------------------------------------------------------------------------------------------------------------------------------
1 -14.50 -25.00 25.49 0.03
2 -14.50 -8.33 25.49 0.00
3 -14.50 8.33 25.49 0.00
4 -14.50 25.00 25.49 0.00
5 14.50 25.00 25.49 0.00
6 14.50 8.33 25.49 0.00
7 14.50 -8.33 25.49 0.00
8 14.50 -25.00 25.49 0.03
------------------------------------------------------------------------------------------------------------------------------------------------------------
----------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 0.00 [lb/in2]
Minimum bearing pressure 0.00 [lb/in2]
Maximum anchor tension 15.56 [kip]
REFER DESIGN DRAWING FOR
Minimum anchor tension 8.22 [kip] BASE PLATE DESIGN
Neutral axis angle 0.00 [deg]
Bearing length -53.46 [in]
Page6
----------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[in] [in] [kip] [kip]
--------------------------------------------------------------------------------------------------------------------------------------------------------------
1 -14.50 -25.00 -25.49 8.22
2 -14.50 -8.33 -25.49 10.66
3 -14.50 8.33 -25.49 13.11
4 -14.50 25.00 -25.49 15.56
5 14.50 25.00 -25.49 15.56
6 14.50 8.33 -25.49 13.11
7 14.50 -8.33 -25.49 10.66
8 14.50 -25.00 -25.49 8.22
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Results for tensile breakout (DL1)
REFERENCES
[9] AISC 2005, Design Examples Version 13.0, pp. IIC-26 - IIC-27
Page7