Professional Documents
Culture Documents
Total Number of question are 36, out of which correct 30 question will be considered for Evaluation.
Spur gear
Helical gear
Bevel gears
Clear selection
Spur gear
Helical gear
Bevel gears
Clear selection
Spur gear
Helical gear
Spiral gear
Clear selection
Positive drive
Bulky construction
Clear selection
Hypoid gears
yp g
Clear selection
Pressure point
Pitch point
Module
Contact point
Clear selection
d/t
2d/t
d/2t
d/3t
Clear selection
common normal to the pitch surface cuts the line of centres at a fixed point
None of the above
Clear selection
Clear selection
10) In involute gears what is the effect of center distance variation on velocity
ratio?
Clear selection
Clear selection
12) The smaller and generally the driving gear of a pair of mated gears is called
pitch
module
rack
pinion
Clear selection
13) In spiral gears; if normal circular pitch is 13 mm, what is the normal module?
40.84 mm
2.06 mm
4.13 mm
13 mm
Clear selection
90 degrees
45 degrees
180 degrees
270 degrees
g
Clear selection
Spur gears
Helical gears
Bevel gears
Spiral gears
Clear selection
[cos ( θ + Φ) – 1] / [ cos ( θ – Φ) – 1]
[sin ( θ + Φ) – 1] / [ cos ( θ – Φ) – 1]
[cos ( θ + Φ) + 1] / [ cos ( θ – Φ) + 1]
[sin ( θ + Φ) – 1] / [ sin ( θ – Φ) – 1]
Clear selection
Helical gears
Bevel gears
Spiral gears
p g
Clear selection
18) If lead angle of worm is 13degree and lead of worm is 40 mm. Find pitch
circular diameter of worm
53.22 mm
27.67 mm
55.15 mm
Clear selection
(θ + α) / 2
(θ – α) / 2
Both a. and b.
Clear selection
20) Which of the following type of gear pair is used in steering mechanism?
Spiral gears
Helical gears
Helical gears
Bevel gears
Clear selection
21) The angle at which the teeth of the gear are inclined to the axis of a gear is
called as
pitch angle
normal angle
helix angle
gear angle
Clear selection
shaft angle
Clear selection
23) When large gear reductions are needed _________ gears are used.
helical
bevel
spur
worm
Clear selection
24) For two gears having shaft angle 90° and friction angle 6°, find the maximum
efficiency of the helical gears.
81.07%
79.02%
85.64%
89.23%
Clear selection
Speed of driven shaft and (speed of driving shaft + speed of idler gears)
Speed of driving shaft and (speed of driven shaft + speed of idler gears)
Clear selection
for odd number of intermediate wheels input and output gears have like motion
for even number of intermediate wheels input and output gears have like motion
for random number of intermediate wheels input and output gears have like motion
None of the above
Clear selection
27) In which type of vehicles, differential gear box is mounted on rear wheel axle?
both a and b
Clear selection
shaft other than input and output shafts carry more than one gear
Clear selection
Clear selection
30) In a clock mechanism, the gear train used to connect minute hand to hour
hand, is
Clear selection
31) Which type of gear train supports only one gear on each shaft
Clear selection
32) If the ratio of angular velocities of the driving and driven members in simple
epicyclic gear train is two and torque on input member is 100 Nm find the torque
on output member
Clear selection
1 dof
2 dof
3 dof
4 dof
Clear selection
34) Which of the following device allows the wheels of a car to rotate at two
different speeds
clutch
differential
brake
engine
Clear selection
35) Which gear train is used for higher velocity ratios in a small space
Reverted
Epicyclic
Compound
Simple
Clear selection
36) In a gear train input Gear A is in mesh with gear B. Gear B is compounded
with gear C which is in mesh with output Gear D.If speed of gear A is 100 rpm.
Number of teeth on gear A and gear B are 60 and 30 while that on gear C and D
are 20 and 40 respectively. Find the speed of gear D
200 rpm
100 rpm
300 rpm
50 rpm
Clear selection
Back Submit
This form was created inside of SNJB (Jain Gurukul). Report Abuse
Forms