Professional Documents
Culture Documents
3M Single Bond Universal Adhesive: Technique Guide
3M Single Bond Universal Adhesive: Technique Guide
Universal Adhesive
Technique Guide
MENU ›
2
Technique Guide
We want you to get the best results using
Menu
3M™ Single Bond Universal Adhesive in Click or tap to jump to the desired technique.
your restorative procedures. That's why
we've created this interactive Technique
Guide. In it, you'll find a list of indications Indications .....................................................................................................................................3
and simple technique guides for the most
commonly performed procedures. Each
guide has step-by-step illustrations and
Technique Guides
easy instructions that are important to know
in advance of the procedure.
Etching Techniques ........................................................................................................... 4
Veneers ................................................................................................................................ 11
MENU
Indications *
Etching Techniques *
or
➀ ➁ ➂ ➃ 5a 5b
Do not squeeze Hold the shaft of the With the thumb and Turn the disposable Option A: For easy Option B: During the
the L-Pop™ blister disposable applicator index finger of the applicator back and application in the treatment, press all of
without the disposable with one hand, other hand, squeeze forth in the liquid to cavity, the disposable the liquid into the open
applicator. covering the blister the reservoir of the cover it completely. applicator can be depression end with
opening with your L-Pop blister, starting bent while it is still in your thumb and index
thumb. This will prevent with the outer end, in the L-Pop blister. In finger to rewet the
the etching liquid from the direction of the order to do this, only applicator.
spraying out. disposable applicator. pull the disposable
applicator out of the
blister far enough so
that the narrow section
of the applicator shaft
can be seen. Fold the
applicator shaft at
this location over your
thumbnail.
➀ ➁ ➂ ➃ ➄
The dosing bottle To open, take the bottle Hold the bottle upside After use, carefully The cap audibly snaps
cap has a thumb in your hand, place your down in a vertical close the bottle again into place when
depression so that it thumb in the thumb position and pour the by applying pressure to pressed closed, and
can be opened to one depression, and push required quantity of the lever from above. a small, even gap
side and closed again the cap to the side until 3M™ Single Bond between the cap and
with one hand. The cap it remains in the open Universal Adhesive in a bottle can be seen all
will remain open if the position. mixing well. Protect the the way around.
opening angle is > 90°. adhesive in the mixing
well from light.
Direct
Restorations
*
➀ ➁ ➂
Following the selective enamel Gently air dry the adhesive for Light cure for 10 seconds.
etch or total etch of the enamel approximately 5 seconds to
and dentin, apply the adhesive evaporate the solvent.
to the prepared tooth and rub it
in for 20 seconds.
Bonding of Dual-Cure
Cements and Core
Build-up Materials
➀ ➁ ➂ ➃
lace one drop each of
P Apply the adhesive or Gently air dry the adhesive Light cure for 10 seconds.
3M™ Single Bond Universal adhesive mixture to the for approximately 5 seconds (Optional step with 3M™
Adhesive and dual cure prepared tooth and rub to evaporate the solvent. RelyX™ Ultimate Cement.)
activator* in a mixing well it in for 20 seconds.
and mix for 5 seconds.
* The 3M™ Single Bond Universal Dual Cure
Activator is not required when using RelyX
Ultimate Cement. When using RelyX Ultimate
Cement, please proceed to Step 2.
Bonding of Self-Cure
Composites
Complete steps 1–4 prior to application of
the self-cure composite.
➄ ➅
Apply the adhesive or Air dry for 5 seconds. Do not light cure!
adhesive mixture to the Proceed with cementing the restoration
restoration for 20 seconds. according to manufacturer’s instructions.
Fissure Sealants *
➀ ➁ ➂ ➃
After cleaning the Gently air dry Apply a light-cure Light cure the sealant
surface with polishing the adhesive for fissure sealant. and adhesive together
paste or by powder approximately 5 according to the
blasting, apply the seconds to evaporate sealant manufacturer's
adhesive to the the solvent. Instructions for Use.
prepared tooth and rub
it in for 20 seconds.
10
➀ ➁ ➂ ➃ ➄
After the glass ionomer Gently air dry the Light cure for 10 If needed, adjust the Use a damp cloth
has been finished, apply adhesive for seconds. occlusion and reapply or cotton pellet to
the adhesive to the approximately adhesive to the ground remove the oxygen
restoration surface and 5 seconds to places to protect the inhibition layer.
rub it in for 20 seconds. evaporate the solvent. filling from drying out.
11
Veneers *
➀ ➁ ➂ ➃ ➄ ➅
Apply a commonly used inse thoroughly with
R Dry with cotton pellets. Apply 3M™ Single Bond Gently air dry the adhesive Do not light cure!
phosphoric acid etching water for 10 seconds. Universal Adhesive for approximately 5
gel (about 35%), e.g., 3M™ immediately to the entire seconds to evaporate the
Scotchbond™ Universal surface of the enamel solvent.
Etchant, to the enamel and and dentin and rub it in
dentin for 15 seconds. for 20 seconds.
➆ ➇ ➈ 10 11 12
www.3M.com
3M Deutschland GmbH
Location Seefeld
3M Oral Care
3M ESPE • ESPE Platz
2510 Conway Avenue
82229 Seefeld • Germany
St. Paul, MN 55144-1000 USA 3M, ESPE, L-Pop, RelyX and Scotchbond are all trademarks
Phone 1-800-634-2249 Info3MESPE@mmm.com of 3M or 3M Deutschland GmbH. Used under license in
Web 3M.com/dental www.3MESPE.com Canada. © 3M 2017. All rights reserved.