Professional Documents
Culture Documents
Code: A01-202
Description:Master-positioning sensor does not go OFF even when
the write pulse motor is reversed during the master-positioning or at
start ofmaster-making operation.
Code: A01-206
ﻣﺭ
Description:Timeout error during master-making operation
Code: A01-211
Code: A01-214 ﻛﺯ
Description:Master-positioning sensor is ON during standby.
Code: A02-509
Description:Master-loading sensor was OFF when the master was
ﺭﻳ
Code: A04-303
Description:Master-disposal jam sensor was OFF at both 120 and
180 degrees drum angle.
Code: A04-314
Description:Master-disposal error (recovery error).
Code: A05-304
Description:Master-disposal jam sensor was ON at the completion
of the master-disposal operation.
Code: A05-315
Description:The master-disposal jam sensor was ON when the
master disposal box was set in the machine.
Code: A06-403
Description:Paper-feed-tray upper or lower safety switch is OFF.
Code: A07-409
Description:Paper-ejection sensor was OFF when the paper should
have arrived, and the paper sensor was ON when the machine
ﻣﺭ
stopped (Papermisfeed).
Code: A07-412
Code: A07-413
ﻛﺯ
Description:Paper sensor was OFF three times in succession when
a paper misfeed was detected (paper misfeed).
Code: A07-418
ﻣﺔ
Code: A07-429
ﺭﻳ
Code: A07-432
ﺯﻭ
Code: A08-410
Description:Paper-ejection sensor was OFF when paper should
have arrived, and the paper sensor was OFF when the machine
stopped (paper jamon the print drum).
Code: A08-421
Description:Paper sensor was ON when the paper should have left
the paper sensor during feeding of long paper in long-length paper
mode (paperlonger than 555 mm).
Code: A09-411
Description:Paper-ejection sensor was ON when the paper should
have left the paper-ejection sensor.
Code: A09-417
Description:Paper-ejection sensor was ON at the start of machine
operation when the START button was pressed.
Code: A09-431
Description:Paper-ejection error (recovery error).
ﻣﺭ
Code: A10-102
Description:Original-registration-sensor remaining jam
Code: A10-103
ﻛﺯ
Description:Original-IN-sensor remaining jam
Code: A10-105
Description:Original-registration-sensor non-arrival jam
ﺧﺩ
Code: A10-106
Description:Original-IN-sensor non-arrival jam
ﻣﺔ
Code: A10-107
Description:Original-OUT-sensor non-arrival jam
ﺭﻳ
Code: A10-109
Description:An original feed error occurred, due to opening the AF.
ﺯﻭ
Code: A10-162
Description:No original in AF during AF master making.
Code: A16-525
Description:Waiting for the master to be removed.
Code: A17-209
Description:Cutter home-position switch is OFF at the start of
master-making or master-set operation.
Code: A34-218
Description:Request to resetting the master.
Code: B22-721
Description:With the “Tape separation” function set ON, no power is
supplied to the job separator when start key is pressed.
Code: B22-727
Description:After cluster-A signal turned ON, BUSY-signal stayed
"L" more than 7 seconds (power to job separator was turned OFF
while the tape isbeing ejected.
Code: B23-722
Description:With the “Tape separation” function set ON, no tape
ﻣﺭ
detected in the job separator when the start key is pressed.
Code: B23-723
Code: B24-724
ﻛﺯ
Description:No tape remains in job separator upon completion of the
tape-ejection operation.
Code: B24-725
ﻣﺔ
Code: B24-726
ﺭﻳ
Code: B31-916
Description:Network cable is not connected when the machine is
powered ON.
Code: B32-917
Description:Communication error on the network.
Code: B32-920
Description:Error detected by Network Interface Card (NIC) - NAK
(negative acknowledgement was received).
Code: B33-931
Description:DHCP server is not found with DHCP ON.
Code: C01-512
Description:The ink sensor did not go ON even when inking was
performed for the preset period.
Code: C01-563
Description:Ink remaining amount is zero.
Code: C01-574
Description:Inkless error was detected 5 times consecutively on one
same ink bottle.
ﻣﺭ
Code: C02-200
Description:The master end was detected twice in succession at 10-
milliseconds intervals during master transport.
Code: C02-240
ﻛﺯ
Description:Master remaining amount is zero
Code: C03-308
ﺧﺩ
Description:Compression detection position was reached before the
master-compression-motor encoder-sensor count reached the
specified level,after the master compression motor turned ON in the
ﻣﺔ
compression direction.
Code: C03-313
Description:Master removal box full detected by the master removal
ﺭﻳ
count.
Code: C04-402
ﺯﻭ
Code: D01-526
Description:Print drum is not set in the machine (drum connection
signal, drum safety switch, and drum-lock sensor is OFF.
Code: D01-527
Description:Print drum connection signal is OFF when the print
drum was inserted in the machine.
Code: D01-528
Description:Print drum safety switch is OFF when the print drum
was inserted in the machine.
Code: D01-530
Description:Print drum connection signal does not go OFF within 5
seconds after the print drum safety switch went OFF when the print
drum waspulled out.
Code: D02-532
Description:Incorrect print drum is used.
Code: D03-533
Description:Ink cartridge set sensor is OFF.
ﻣﺭ
Code: D04-534
Description:Incorrect ink cartridge is used.
Code: D04-560
ﻛﺯ
Description:Ink TAG is not detected on ink bottle.
Code: D04-561
ﺧﺩ
Description:Ink cartridge communication error (communication with
the ink cartridge was interfered by noise).
ﻣﺔ
Code: D04-562
Description:Wrong ink cartridge information.
Code: D04-564
ﺭﻳ
Code: D05-210
ﺯﻭ
Code: D07-310
Description:Disposal-box safety switch is OFF.
Code: D08-224
Description:Master making unit is not set (both the safety switch and
lock sensor are OFF).
Code: D08-226
Description:Master making unit safety switch is still OFF when the
master making unit is set in position.
Code: D08-228
Description:Master making unit lock sensor is still ON even after the
master making unit safety switch went OFF, when the master making
unit waspulled out of the machine.
Code: D09-212
Description:Master-making-unit set sensor is OFF (sensor light path
is free).
Code: D11-535
ﻣﺭ
Description:Front cover set switch is OFF.
Code: D13-9
Code: D17-236
Description:Incorrect master roll.
ﻛﺯ
Description:The rear cover is opened (serviceman safety switch is
OFF).
ﺧﺩ
Code: D17-237
Description:Master roll undetected.
ﻣﺔ
Code: D17-238
Description:Master roll communication error.
ﺭﻳ
Code: D17-239
Description:Wrong master roll detected.
ﺯﻭ
Code: D17-241
Description:Detected a mismatch in master roll information.
Code: D18-522
Description:Print drum ready for release (solenoid is ON).
Code: D19-223
Description:Master making unit ready for release (solenoid is ON).
Code: D22-540
Description:Error in access to the Drum PCB (unable to read from
or write on the Drum PCB).
Code: E01-10
Description:Battery voltage was less than 2.5 V when the power
was switched ON (weak battery: time to replace battery).
Code: E02-11
Description:Master counter reached the value set for the
maintenance call (value set by test mode). [The message appears
when either the power isturned ON, the unit is reset, or when the
machine operation ended.]
Code: E02-12
ﻣﺭ
Description:Copy counter reached the value set for the maintenance
call (value by set test mode). [The message appears when either the
power isturned ON, the unit is reset, or when the machine operation
ended.]
Code: F01-15
Description:There is no master on the print drum at the start of
printing.
ﺭﻳ
Code: F02-18
Description:Paper size does not match with the image size on the
print drum at the start of printing.
ﺯﻭ
Code: F03-16
Description:Multi-up was selected using custom size paper.
Code: F05-19
Description:In master making, the print quantity selected is less than
the minimum print quantity.
Code: F10-21
Description:Paper size does not match with the size of image on the
print drum when test print is selected and activated.
Code: F22-33
Description:Next original is not placed on flatbed for multi-up
operation.
Code: F37-50
Description:Original was set on the AF with book mode selected,
when master making is activated.
Code: F50-910
Description:Auto-printer-selection is disabled due to error on linked
ﻣﺭ
printer.
Code: F54-923
Code: F55-924
ﻛﺯ
Description:Auto-printer-selection is disabled due to no paper in the
linked printer.
Code: F58-927
ﻣﺔ
Code: H1-566
Description:Requesting ink color information input (Ink-TAG
ﺭﻳ
related).
Code: H2-567
ﺯﻭ
Code: H3-568
Description:Requesting test printing print density information input
(Ink-TAG related).
Code: H4-242
Description:Requesting master-making density information input
(Master-TAG related).
Code: H5-243
Description:Requesting Print density information input (Master-TAG
related).
Code: P01-520
Description:Main encoder sensor does not go ON/OFF within 10
milliseconds after the main motor activates.
Code: P01-521
Description:B-positioning sensor status does not change even after
3,033 pulses after the main motor activates.
Code: P01-524
Description:Clamp unit is not at the home position while the print
ﻣﺭ
drum is in operation (except during master disposal).
Code: P01-537
Code: P01-538 ﻛﺯ
Description:Print drum failed to stop at position B. (over-run)
same time.
Code: P02-401
Description:Overload current was detected in the elevator motor.
ﺭﻳ
Code: P02-404
Description:The lower-limit sensor does not go OFF within 2
ﺯﻭ
Code: P02-405
Description:The upper-limit sensor does not go ON within 12
seconds after the elevator motor operates in the raising direction.
Code: P02-406
Description:The upper-limit sensor does not go OFF within 2
seconds after the elevator motor operates in the lower direction from
the upper-limitposition.
Code: P02-408
Description:The upper-limit sensor is OFF continuously for over 2
seconds during operation of the elevator servo action to raise the
feed tray.
Code: P03-500
Description:Clamp sensor A is OFF after the completion of the
clamp unit initialization or home positioning movement.
Code: P03-501
ﻣﺭ
Description:Clamp sensor B does not change within 1 second from
the time the clamp motor operates in the correct direction.
Code: P03-502
ﻛﺯ
Description:Clamp sensor B does not change within 1 second from
the time the clamp motor operates in the reverse direction.
Code: P03-503
ﺧﺩ
Description:Clamp sensor A does not go ON within 3 seconds when
the clamp unit makes initialization movement.
ﻣﺔ
Code: P03-504
Description:At the start of Clamp plate open/close action, the the
detection sequence of clamp-sensors A & B is abnormal.
ﺭﻳ
Code: P03-505
Description:At the start of print drum Positon-A compensation
movement, the detection sequence of clamp-sensors A & B is
ﺯﻭ
abnormal.
Code: P03-506
Description:At the start of Clamp unit Home-positioning movement,
the detection sequence of clamp-sensors A & B is abnormal.
Code: P03-507
Description:Clamp sensor A is ON after the clamp release action is
completed.
Code: P03-508
Description:Clamp sensor A is ON after the A-position
compensating movement is completed.
Code: P04-513
Description:The overflow sensor was ON for a set number of times
in succession during the 10-millisecond-interval overflow-sensor
check.
Code: P05-603
Description:The vertical-centering sensor does not switch ON even
when the vertical-positioning pulse motor activated in the image-
down direction for5 seconds during vertical home positioning
movement.
ﻣﺭ
Code: P05-604
Description:The vertical-centering sensor does not switch OFF even
Code: P05-605
ﻛﺯ
when the vertical-positioning pulse motor activated in the image-up
direction for 5seconds during vertical home positioning movement.
Code: P05-612
Description:The one-step-positioning key was pressed with vertical-
print-position information undefined.
ﺭﻳ
Code: P08-951
Description:Print job executed was not in correct RisoRinc format.
ﺯﻭ
Code: P11-600
Description:Print pressure HP sensor does not switch ON within 3.9
seconds after the print pressure pulse motor activated towards higher
pressureduring home positioning operation.
Code: P11-601
Description:Print pressure HP sensor does not switch OFF within
4.6 seconds after the print pressure pulse motor activated towards
lower pressureduring home positioning operation.
Code: P12-300
Description:Overload current was detected in the master removal
motor.
Code: P12-301
Description:Master compression motor lock when moving
compression plate up.
ﻣﺭ
Code: P12-305
Description:Master compression sensor does not go ON within 6.5
seconds after the master compression motor operates in the return
direction.
Code: P12-307
ﻣﺔ
Code: P12-309
Description:Master-compression-motor encoder sensor count did
not change as the master compression motor activated in the
ﺯﻭ
Code: P12-316
Description:Master-compression-motor encoder sensor count did
not change within 10 milliseconds after the master compression
motor activated.
Code: P13-203
Description:Cutter HP switch does not go OFF within 100
milliseconds after the cutter motor is activated.
Code: P13-205
Description:Master-positioning sensor is ON when the print drum
rotates through the preset angle following master cutting.
Code: P13-221
Description:Both the cutter HP switch and cutter stop position switch
are ON at the same time.
Code: P13-222
Description:Cutter HP switch does not go ON within 450
ﻣﺭ
milliseconds after the cutter home positioning operation started.
Code: P13-231
Code: P13-232
ﻛﺯ
Description:Cutter HP switch does not go OFF within 500
milliseconds after the cutter moved out from the home position.
Code: P13-233
ﻣﺔ
Code: P13-234
Description:Cutter HP switch does not go ON within 2 seconds after
the cutter home positioning operation started.
ﺯﻭ
Code: P14-114
Description:Incorrect main-unit data.
Code: P14-115
Description:The scanner operation is not completed within the set
time.
Code: P14-116
Description:Timeout error for black shading compensation. (RZ3
series only)
Code: P14-123
Description:Offset adjustment not completed within set time. (RZ3
series only)
Code: P14-124
Description:Gain adjustment not completed within set time. (RZ3
series only)
Code: P14-125
Description:Offset adjustment not completed.
ﻣﺭ
Code: P14-126
Description:Gain adjustment not completed.
Code: P14-135
ﻛﺯ
Description:Malfunction detected during offset adjustment. (RZ3
series only)
ﺧﺩ
Code: P14-136
Description:Malfunction detected during offset adjustment. (RZ3
series only)
ﻣﺔ
Code: P14-137
Description:Malfunction detected during black shading
compensation. (RZ3 series only)
ﺭﻳ
Code: P14-138
Description:Malfunction detected during white shading
ﺯﻭ
Code: P14-170
Description:Even though the read pulse motor stopped according to
the sensor detection, the stopping position does not correspond with
theprogrammed position. (GA control error).
Code: P15-110
Description:ABC (auto-base-control) timeout. The original does not
move from the ABC scanning position on the AF unit.
Code: P15-111
Description:Operation command was made to the AF unit without
24 volts supplied to the AF unit.
Code: P15-131
Description:Riso printer received an undefined command from the
AF unit.
Code: P15-132
Description:Riso printer detected communication sequence error
from the AF unit.
Code: P15-133
Description:Communication error with AF unit (ACK or NAK error).
ﻣﺭ
Code: P15-134
Description:Riso printer could not send command to the AF unit
within the set time.
Code: P17-20
Description:Solenoid counter is not connected.
ﺭﻳ
Code: P18-531
Description:Print drum lock sensor is still ON even after 100
milliseconds after the print drum lock solenoid is activated.
ﺯﻭ
Code: P19-207
Description:TPH pressure sensor does not go OFF within 2 seconds
after the thermal-pressure motor activates in the decompressing
direction, orduring home positioning operation.
Code: P19-208
Description:TPH pressure sensor does not go ON within 2 seconds
after the thermal-pressure motor activates in the decompressing
direction.
Code: P19-217
Description:TPH pressure sensor does not go ON within 2 seconds
after the thermal-pressure motor activates in the compressing
direction.
Code: P20-415
Description:Paper-ejection-wing home sensor does not go OFF
within 7,000 milliseconds after the paper ejection wing motor
activates in thecounterclockwise direction from the home position.
ﻣﺭ
Code: P20-416
Description:Overload current was detected in the paper-ejection
motor.
Code: P25-26
Description:Battery voltage was below 2.3 volts (too low) when the
ﺭﻳ
Code: P92-570
ﺯﻭ
Code: P93-932
Description:No reply from the NET-C network interface card while
accessing to the network interface card.
Code: P93-933
Description:No response from NET-C for 90 seconds during NET-C
initialization.
Code: P94-225
Code: P95-59
Description:Machine serial-number information sent from SH-PCB
does not match with the machine serial number information in the
MCTL PCB.
Code: P96-171
Description:TPH resistance value not input.
Code: P96-172
ﻣﺭ
Description:Scanner adjustment not completed.
Code: P96-433
Code: P96-569
ﻛﺯ
Description:Paper size width potentiometer test-mode setting is not
completed.
Code: P96-613
ﻣﺔ
Code: P98-119
Description:Image processing PCB trouble.
ﺭﻳ
Code: P98-120
Description:Scanner communication problem. (RZ3 series only)
ﺯﻭ
Code: P98-129
Description:Faulty Scanner GA PCB. (RZ3 series only)
Code: P98-2
Description:No reply from Mini-Rosa PCB when the machine power
is turned ON even though the Rosa connection signal is ON.
Code: P98-245
Description:Master transfer time-out error during master making
(Write pulse motor error).
Code: P98-38
Description:Machine data on EEPROM does not match with that on
the SH-PCB
Code: P98-39
Description:Improper EEPROM on the SH-PCB.
Code: P98-46
Description:The DIMM capacity does not match.
ﻣﺭ
Code: P98-5
Description:Hardware error.
Code: P98-51
ﻛﺯ
Description:Touch-panel communication error
Code: P98-53
Description:Failure in calling out the saved Memory settings
ﺧﺩ
(program, mode, user paper information).
Code: P98-54
ﻣﺔ
Code: P98-55
ﺭﻳ
Code: P98-6
Description:FRAM checksum error.
Code: P98-614
Description:Vertical print position data missing.
Code: P98-63
Description:The test-mode memory data stored was outside the
adjustment range.
Code: P98-64
Description:An undefined command was sent in communication
between SH-PCB and MCTL PCB.
Code: P98-67
Description:Communication error 03 between SH-PCB and MCTL
PCB (MCTL PCB side).
Code: P98-68
Description:Communication error 04 between SH-PCB and MCTL
PCB (MCTL PCB side).
Code: P98-69
Description:Communication error 05 between SH-PCB and MCTL
ﻣﺭ
PCB (MCTL PCB side).
Code: P98-7
Code: P98-70 ﻛﺯ
Description:Mini Rosa PCB not connected.
Code: P98-72
Description:Communication error 08 between SH-PCB and MCTL
ﺭﻳ
Code: P98-73
ﺯﻭ
Code: P98-74
Description:Communication error 10 between SH-PCB and MCTL
PCB (SH-PCB side)
Code: P98-75
Description:Communication error 11 between SH-PCB and MCTL
PCB (SH-PCB side)
Code: P98-76
Description:Communication error 12 between SH-PCB and MCTL
PCB (SH-PCB side)
Code: P98-78
Description:Communication error 14 between SH-PCB and MCTL
PCB (SH-PCB side)
Code: P98-79
Description:Communication error 15 between SH-PCB and MCTL
PCB (SH-PCB side)
Code: P98-80
Description:Communication error 16 between SH-PCB and MCTL
ﻣﺭ
PCB (SH-PCB side)
Code: P98-81
Code: P98-82
ﻛﺯ
Description:Communication error 17 between SH-PCB and MCTL
PCB (SH-PCB side)
Code: P98-83
ﻣﺔ
Code: P98-84
ﺭﻳ
Code: P98-934
Description:Main read/write communication error (detected by
read/write side).
Code: P98-935
Description:Main read/write communication error (detected by
machine side).
Code: P98-937
Description:Serial number data missing.
Code: P98-938
Description:FRAM version-down.
Code: P98-948
Description:24V-B does not go ON (a possible burnt 24-volt group-B
fuse).
Code: P98-949
Description:24V-A does not go OFF.
Code: P98-950
Description:24V-B does not fo OFF.
ﻣﺭ
Code: P98-952
Description:Checksum error on the ROSA flash-memory.
Code: P98-953
ﻛﺯ
Description:Unsuccessful writing on the ROSA flash-memory.
Code: P98-98
Description:Machine serial number information on the SH-PCB
ﺧﺩ
EEPROM does not match with that in the FRAM.
Code: P99-936
ﻣﺔ
Description:Software error
ﺭﻳ
ﺯﻭ