Professional Documents
Culture Documents
for
BROMMA TELESCOPIC SPREADER
TYPE: EH170U
General assembly drawing
No:BR1256227
Serial number:30874
SWL: 41 tonne
Customer: SPB, COLUMBIA
End User:
Date of shipping: 2019
_____________________________________________________________________________________
BROMMA CONQUIP AB 00 01 ENG
rev.
Warning!
This Operations manual is intended as a guide to the use and maintenance of
Bromma spreaders.
• DO NOT exeed the Safe Working Load (SWL) of the spreader bar. The
Safe Working Load is found on the nameplate that is permanently affixed
to the side frame of the spreader.
__________________________________________________________________________________
BROMMA CONQUIP AB 00 02 ENG
rev.
Table of contents
1 • INTRODUCTION
5 • SAFETY PRECAUTIONS
6 • START-UP PROCEDURES
7 • MAINTENANCE PROCEDURES
Maintenance instructions
Periodic maintenance procedure
Lubrication instructions
Instructions for adjustment and repairs of major items
12 • APPENDICES
Units and conversion tables
Hydraulic symbols
Electrical symbols
_________________________________________________________________________________
BROMMA CONQUIP 00 03 ENG
rev.01
Bromma Group Manual
0-1-may 02 rev.00 Bromma Conquip
1 • Introduction
• Maintenance.
• Repairs.
• Trouble-shooting.
• Service.
• Spare parts.
0-1-may 02 rev.00 Bromma Conquip
2 • Spreader - Datasheet
Type EH170U
Art.No 1256227
Container Range 20’- 40’
Capacity
Lifting capacity (evenly loaded) 41 tonne
Lifting capacity (10% gravity point off set) 41 tonne
Twinlift capacity 2 x 25 tonne
Twinlift capacity (10% gravity point off set) 2 x 20,5 tonne
Lifting lug capacity (gable end) 4 x 10 tonne
Lifting lug capacity (main beam) 4 x 10 tonne
Operating Movements
Telescoping 20’ to 40’ or 40’ to 20’ 30 s
Twistlock rotation locking or unlocking 90o 1,5 s
Electrical Equipment
Power voltage 400 V AC
Frequency 50 Hz
Control voltage 230 V AC
Control valve 24 V DC
Total power consumption 2x2,2 k + 1x3kW + 3+5,5 =15,9kW
Electrical protection IP 65
Hydraulic Equipment
Pump running Pressure 100 bar
Pump flow 3 x 15 l/min
Tank capacity 3 x 50 l
Normal running temperature (above ambient) 50˚C
Filter type 10 µm
Filter
Pressure line 10 µm
Corrosion protection
All surfaces are grit blasted SA 2.5
Interzinc 72 EPA 069/073 (Interzink 72 EPA 069/073) 50 µm
Intervinux Serie VL (Intervinux Serie VL) 2 x 50 µm
Intervinux Serie VS (Intervinux Serie VS) 50 µm
Min. coating thickness, total 200 µm
______________________________________________________________________________________________________
BROMMA CONQUIP AB 02 01ENG
rev..1
Bromma Group Manual
0-1-may 02 rev.00 Bromma Conquip
3 • Technical description
Functional description
Bromma telescopic spreader EH5 (EH12 & EH170) are fabricated as all
welded, high quality steel, construction. Two pairs of telescopic beams slide in
the centre main frame construction. The telescopic beams are joined together
at the ends by end beams, which house the twistlocks, flipper arms and
hydraulic valves.
The spreader has an inbuilt under clearance of 185 mm. This enables
hatchcovers and containers with protrusions up to 185 mm to be handled. If
larger clearances are required then overweight extension legs need to be fitted.
The spreader is optionally fitted with one set of lifting lugs. Mostly, they are
placed at each corner of the gable end. In case the spreader is provided with
this device, it can be used for handling of badly damaged containers or non-
containerised cargo.
TELESCOPIC SYSTEM
The telescoping system is driven by means of an electric motor and reduction
gearbox connected to an endless chain. This chain is titted with stacks of spring
washers that work as chock absorbers where the chain attaches to the tension
rods.. These tension rods are connected to the end beam. The springs allow for
changes in the length of the spreader up to plus or minus 7 mm . The springs
do not only act as shock absorbers; they also provide a floating possibility for
the twistlocks to handle distorted containers. This "floating" action also
eliminates the need for corner guide rollers.
________________________________________________________________________________________________________
1 of 3 BROMMA CONQUIP AB 03 09 ENG.
rev. x
This brake not only controls the accuracy in stopping the expansion and
retraction but also prevents changes from occurring in the spreader length
during use.
TOWER
The main frame of the spreader is connected to the crane through a sliding
tower assembly. This enables the centre of gravity lifting point to be moved a
maximum of 1,2 meters toward each end of the spreader. This means that
unevenly loaded containers can be picked up horizontally, which is specially
important when loading or unloading in the guides in the ship´s cells. After
unlocking an unevenly loaded container, the sliding tower assembly
automatically returns to the central position
FLIPPERS
Flat gather guides, commonly called flippers, are fitted to each end beam of the
spreader. They are of strong construction and are driven by a powerful
hydraulic motor, which enables easy and fast location of the spreader onto the
containers. The flipper gather is 155 mm and has a gathering torque of
1200 Nm. The flipper arms are always under pressure and each arm has a
shock relief valve, which opens at a pre-set pressure of 45 bar above the
normal working pressure. As soon as the shock load ends the flipper returns to
the vertical position.
Each flipper is controlled by its own solenoid valve and shock relief valve. The
flippers work in pairs along the length of the spreader, individually at the gable
ends, or all together.
The speed of the flipper is approximately 180° in 6 seconds and is
controlled by an orifice plug in the pipe connection to the motor.
TWISTLOCK
Four twistlocks for single container spreader are located in the corners of the
spreader to engage and lift the container. A hydraulic cylinder rotates the
twistlock and two sensors indicate the position of the twistlock, Locked or
Unlocked.
A landing pin safety system is provided to assure that the spreader is properly
landed on the container before rotating the twistlocks.
A spring loaded landing pin near each twistlock is pushed up into the twistlock
housing when the spreader is landed on the container. When the spreader is
properly landed on a container, the landing pin will activate a proximity switch.
Only when all the corners of the spreader are landed, can the twistlocks be
turned. At the same time, the blockading key is moved high enough so the
blockading stop on the twistlock lever arm passes underneath it. If the
spreader is not properly landed the proximity switch will not be activated and
________________________________________________________________________________________________________
2 of 3 BROMMA CONQUIP AB 03 09 ENG.
rev. x
the blockading key will get in the way of the blocking stop. This will stop the
twistlocks from turning.
SIGNAL LIGHT
Near each end of the spreader mainframe there is a set of three signals light,
one green, one red, one white, which can be clearly seen from the crane cabin.
The green and red lights indicate if corresponding twistlocks are unlocked or
locked respectively. The white light indicates when the spreader is properly
"landed", and the twistlocks are correctly engaged in the container corner
castings.
In twinlift spreaders (EH170U), when using the twinlift function, the left side
signal lamps are valid for the left side container and the right side lamps are for
the right side container.
HYDRAULIC UNITS
The hydraulic units are protected inside each end beam. The unit consists of a
built-in tank, variable displacement piston pump, motor valves and filter. The
filter cap is fitted with a pressure relief valve plus or minus 0,14 bar to allow
expansion and contraction of air inside the tank.
The hydraulic components used are designed to work at over 200 bar but
normal working pressure is 100 bar. The hydraulic valves are solenoid
operated and can be tested by hand operating.
The EH170U has a third hydraulic unit placed in the main beam. This unit
provides the four cylinders for center twistlock housings up-down and the four
cylinders for lock-unlock in the central twistlocks with power.
________________________________________________________________________________________________________
3 of 3 BROMMA CONQUIP AB 03 09 ENG.
rev. x
• Design calculations
The spreader structure is designed according to DIN15018 and to the
following loading group which represents a container handling crane.
• HOISTING GROUP H2
• LOADING GROUP B4
LIFTING CASES
The following lifting cases are considered:
1. The spreader should only be hoisted/lowered when all four twistlocks are
fully locked/unlocked.
4. During hoisting the four blockading pins move to the "down" position.
This prevents electrically the twistlocks from moving.
NOTE ! When carrying out maintenance on the twistlocks, the blockading pin clamps can
be fitted to each corner, to by pass the electric and mechanical blockading when running
the twistlock.
__________________________________________________________________________________
BROMMA CONQUIP AB 03 03 ENG
rev.
In-plant testing
STRUCTURAL
Each spreader is fully proof tested in the factory to a minimum of 50%
overload prior to delivery. The proof test loading report enclosed illustrates the
loads applied to the spreader.
All lifting lugs are also proof tested in the factory.
The testing is witnessed and certified by a third part inspection official.
All spreader twistlocks are individually proof tested, stamped and certified to a
loading of 37 tonne.
FUNCTIONAL
Each spreader is run in the factory prior to delivery being controlled by a
specially designed simulator.
__________________________________________________________________________________
BROMMA CONQUIP AB 03 04 ENG
rev. x
4 • Testing records and certificates
______________________________________________________________________________________________________
BROMMA CONQUIP AB 04 01 ENG
rev.
Bromma Group Manual
0-1-may 02 rev.00 Bromma Conquip
5 • Safety precautions
Warnings
The manual contains vital information for the safety of personnel and the
correct use of the spreader.
Bromma Group will not accept any liability for the use of the spreader for
any purposes outside what is described in the manual.
DO NOT exeed the Safe Working Load (SWL) of the spreader bar. The Safe
Working Load is shown on the nameplate that is permanently affixed to the
side frame of the spreader.
Safety precautions
2. The spreader must only be used for the purpose for which it is
designed.
6. Stay clear of all moving parts, such as guide arms (flippers), moving
beams, telescopic chains, etc. A safe distance is 5 meters.
12. Care must be taken when performing any maintenance inside the
spreader frame. It must be carried out under extreme caution and by
personnel familiar with risks related to spreader function and
movements. Serious injury by crushing can occur
13. Contact Bromma Conquip AB before doing any repair work on the
spreader apart from replacing normal wear parts.
14. DO NOT walk or stand beneath the spreader bar during operation.
15. DO NOT attempt to lift a container that is not level (+/- 5°).
19. DO NOT stand between a container and any construction that many
prevent your movement to safety. A definite hazard exists that could
cause serious injury or death by being crushed between the container
and an obstruction (such as a building or another container).
20. Mobile work platforms which are used in repair and service work on the
spreader must be equipped with safety rails and kick plates.
22. The tower must be moved back to the centre of the spreader before it
leaves the container. There must be a good clearance between the
Spreader and the container before slewing the crane boom.
23. When welding might be needed on the spreader with SCS2 assembled,
make sure that it is properly grounded or dismantle the plug connection
and earth cable.
_____________________________________________________________
BROMMA CONQUIP AB 05 02d ENG.
rev.
Bromma Group Manual
0-1-may 02 rev.00 Bromma Conquip
6 • Start - Up procedure
ASSEMBLY OF TOWER (drg no 34476)
2 Suspend the tower from a suitable forklift or crane (tower weight 1,4 t)
using
the main lifting pin (pos 1).
3 Remove the protective material from the robalon pads on tower (pos 2).
Remove the drive sprocket cover (pos 6).
Remove the (2) lifting lugs from main frame of the spreader at the
assembly end
(pos 3).
NOTE: Take care that flipper does not fall down and cause injury!
7 Remove lamp assembly by taking out the quick release fastening from
the four pins and lay the lamp assembly in the main frame.
8 Release the gravity point chain, by removing the two screws and the
locking device from adjuster.
9 You are now able to slide the tower into the main frame close to the
centre.
Note the direction of assembly. Arrows are painted on the tower and
frame.
10 Now replace the lamp assembly, rubber covers and lifting lugs. If the
flipper is rise at this time, care should be taken as it is liable to fall, now
that the motor is empty.
______________________________________________________________________________________________________
1 BROMMA CONQUIP AB 06 02 ENG
rev.
11 Remove the drive sprocket cover (pos 6).
It is now possible to install the chain, complete with the anchor block
fitted.
The chain goes, under the first sprocket, over the centre one and under
the third.
To assist with the chain installation, pull the brake release lever, towards
the back of the motor. It is then possible to turn the motor, using the
handle supplied.
12 Replace the chain back into it's fixing point and tighten the adjusting
screws, until the chain is tight (allow a sag of about 30 mm and place the
tower in middle position) and replace the locking device. Grease the chain.
14 Pass the main plug up through the tower and fix conduit pipes with screws
supplied.
16 Connect the tower motor. The connections are marked u1 and w1 to give
correct position.
19 Check all bolts are tight and the spreader is clear of all discarded material
and tools. Take care that nothing had fallen into the chain.
______________________________________________________________________________________________________
2 BROMMA CONQUIP AB 06 02 ENG
rev.
TOWER FUNCTIONS AND TESTING
The tower function is to level/unlevel loaded containers. Any other use of the
tower is an abuse of the equipment and could result in serious damage.
When the spreader is locked onto a container, it is possible to move the tower
in any direction. The tower will stay where it is placed. The return to the middle
position is done by the crane driver. When he has driven the tower to yellow or
blue, it goes always to the middle position.
To test the newly assembled unit, place the blockading pin clamps onto the
spreader and lock the twistlocks. With the spreader on the ground, commence
to travel the tower towards one end of the spreader. Now hold a piece of
metal, i.e. spanner or screwdriver, in front of the stop switch, for the end that
the tower is travelling. The tower should now stop.
Try the other direction. If both of the limits work, travel the tower to both ends
of the spreader, to confirm the limits work on the detection bar. When at each
end, unlock the twistlocks and release a clamp, to confirm the tower returns to
it's centre position. If any of these functions fail, please seek advice.
WARNING!
Use the tower only to level loads, or serious damage may occur!
Never use the hand crank on the motor with power connected, or serious
injury may occur!
______________________________________________________________________________________________________
3 BROMMA CONQUIP AB 06 02 ENG
rev.
Start - Up the spreader
1. Before any connection to container crane, place the main frame of the
spreader on trestles or similar about 0,7 m height and in such a way that the
flipper arms can be lowered.
3. Connect the main current and control supply to the spreader. Connect the 24
pin plug to the service panel.
4. Start the electric motor of the hydraulic units by turning the ”pump on” switch on
service panel.
5. For testing of the twistlocks all 4 blockading pins should be in ”up” position. This
is achieved by using a blockading pin clamp. In the ”down” position the
blockading pins electrically and mechanically block all twistlock rotation.
6. Test all functions of the spreader using the push buttons and switches on the
service panel.
a) When ”pump on” switch is on, both electric motors should be running in
gable ends.
b) Operate the push buttons to put the spreader in the different length positions.
As an additional length, check that the twistlock centre length is marked on
the plate positioned on side of the main beam.
c) Check that the flippers works in pairs along the length of the spreader,
individually at the gable ends, or all together by pressing the appropriate
buttons.
d) Check that when clamps are fitted to the blockading pins and all pins are up,
this will be indicated by the white lights on the spreader.
e) Check that the twistlocks lock/unlock and that the light indicators on the top
of the spreader main frame indicate red when locked and green when
unlocked.
7. Check that the pump operating pressure is 100 bar.
______________________________________________________________________________________________________
4 BROMMA CONQUIP AB 06 02 ENG
rev.
8. Check each end hydraulic assembly to ensure there are no oil leaks.
9. Note that the solenoid valves operating flippers and twistlocks can be
manually operated if required.This is achieved by pushing the end of the
solenoid with a small screwdriver. As power is generally always on the
solenoid, the plug connection has to be disconnected first.
10. Service and lubrication should be carried out in accordance with the
lubrication manual.
______________________________________________________________________________________________________
5 BROMMA CONQUIP AB 06 02 ENG
rev.
Bromma Manual
Digital caliper
Shaft dimension
2016-06
1 Rev. 00 Bromma 2
Bromma Manual
Hole dimension
Bromma Conquip
7 • Maintenance procedures
Maintenance Instructions
IMPORTANT!
When the spreader is disconnected from the crane the heating function
(if fitted) must always be connected and energised.
Pos. 1
TWISTLOCK (drg no 22808)
All twistlock are to be greased through the greasecups 4 per spreader.
Pos. 2
TWISTLOCK CYLINDER & BEARING HOUSING IN TOWER (drg no 22808)
Piston rod ends are to be greased. 8 per spreader. Bearing housing in tower.
2 per spreader.
Pos. 3
HYDRAULIC UNIT (drg no 22809)
Oil is to be changed after first 50 hours, then after every 1000 hours.
Pos. 4
OIL FILTER (drg no 22809)
Filter is to be changed after first 50 hours, then after every 1000 hours of
operation or when the indicator is red.
Pos. 5
LIFTING SHAFTS (drg no 22808)
(If the spreader/headblock is equipped with lifting shafts).
ACTION! To be greased.
Pos. 6
GLIDE PLATE (drg no 22810)
The robalon glide plates are to be replaced when the thickness is down to
17 mm.
ACTION! To be checked.
Pos. 8
TELESCOPIC GEARBOX (drg no 22808 & 22809)
Oil level is to be checked through dismantled oil level plug. Bearings at the
gearbox and the pedestal are to be greased through greasecups.
Pos. 9
ALL ROLLER CHAINS AND TENSION WHEEL (drg no 22808)
Roller chains and tension wheel are to be checked from abrasion and
greased.
Pos. 10
SIGNAL LAMPS (drg no 22810)
Vibration proof glow lamp.
ACTION! To be checked.
Pos. 11
TELESCOPIC BEAMS (drg no 22808)
To be greased as follows:
2. In fully expanded position, with a brush on the sliding area under the
telescopic beams ca 100g/ at interval min.1000 hour. The amount of
grease and service interval depends on spreader use and environmental
circumstances which vary from place to place.
Pos. 12
ELECTRICAL MOTORS (Only for EH5)
Adjust brakes as per attached instructions.
A-A
1:5
Number Detail ID Quantity Title (Item,CO) Description (Item,CO) Revision
BR24169 - - FLIPPER ARM ASSY. - g
BR60628 1 2 GEAR BOX FLIPPER ARM TYPE 1 i
BR60629 2 1 GEAR BOX FLIPPER ARM TYPE 2 i
BR24168 3 1 FLIPPER ARM - d
BR62595 4 1 FLIPPER ARM - d
BR24167 5 1 FLIPPER ARM - d
BR76842 6 12 SCREW M6S 20x110 DACROMET, CLASS 10.9, ISO 4014 a
BR1109317 7 12 NUT LOC-KING M20 DIN 985, FZB, CLASS 10 -
BR75292 8 24 WASHER BRB 21x36x3 FZB, SMS 70 -
BR47678 9 10 SPACER - d
BR72010 10 6 KEY 20X12X30 TK, SMS 2307 a
BR401528 11 2 BUFFER ASSY. - a
BR1119988 12 1 BUFFER ASSY. - -
REV DESCRIPTION ECO-No. DATE BY
a FZB fasteners replace by
- 2009-06-11 IBC
A4 fasteners
b 3D model added 005719 2013-12-23 varmani
LS/2 = 1300
THIS DRAWING IS COPYRIGHT AND IS PROPERTY OF BROMMA CONQUIP. THE DESIGN AND/OR CONSTRUCTIONS CONTAINED THEREIN MAY NOT BE
A-A ( 1 : 2 )
COPIED OR REPRODUCED WITHOUT THE WRITTEN CONSENT OF THE OWNER.
4
2
3
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
- - - -
DATE MATERIAL SHEET WEIGHT TOLERANCE GENERAL
BR39047
REV DESCRIPTION ECO-No. DATE BY
Modified 3d model. Now representations for different
b connection points for different tension rods. 0004097 2009-05-06 CLN
c Tolerance and note added 0006816 2010-07-30 JLM
No changes, revision changed to d in PDM system and
d 2015-02-26
could not be reversed
3 2 1
COPIED OR REPRODUCED WITHOUT THE WRITTEN CONSENT OF THE OWNER.
To be locked with screw after adjustment. Adjusted to chain tension 40 5 Nm, repeated after 200 times test.
c
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
CHAIN ASSY A3 d
- DRAWING NUMBER
38073
Number Detail ID Quantity Title (Item,CO) Description (Item,CO) Revision
BR38073 - - CHAIN ASSY - d
BR47468 1 2 CHAIN SIPLEX 1 1/2 INCH 177H, 119 LINKS b
BR61698 2 2 SHOCK ABSORBER CHAIN ASSEMBLY g
BR71512 3 4 CHAIN-LOCK SIMPLEX 1 1/2 IN 177H -
PERIODIC MAINTENANCE PROCEDURE
RUNNING-IN OF A NEW SPREADER
2. Check that all hydraulic tank mountings are tight. Twistlock pin
4. Carefully inspect all hoses, hose clips and hose connections. Defective
hydraulic hoses and connections may cause personal injury when jets of
liquid escape under high pressure.
If the work requires that the electrical supply remains connected then staff on
or in the vicinity of the spreader must be informed that it could move.
NOTE. See the twistlock drawing and/or the separate adjustment instructions
for the adjustment of the twistlock end stop switches after reassembly.
--------------------------
2
If the spreader is equipped with twistlock counter
3
If there is no hour counter or twistlockcounter
4
If the spreader is equipped with twistlock counter
5
If there is no hour counter or twistlock counter
6
Only for floating twistlocks
When ordering a new hydraulic pump always state the direction of rotation as
marked on the old pump housing.
NOTE. Every time the pump is emptied, new oil must be added until it starts
to run out of the drain hose.
These are cross over relief valves which relieves excess hydraulic pressure
caused by external forces on the flipper arms or the telescopic system. The
rising hydraulic pressure acts against the spring to open the flow path to the
other port.
All leakage’s through these valves at the normal operating pressure of the
pump (lower setting than the pump's operating pressure) cause a substantial
increase in the temperature of the hydraulic oil. Leaks of this type are often
indicated by a hissing sound coming from the relief valve.
4. Remove the chain pin connected to the shock absorber by pulling out the
cotter pin.
6. Install a new chain or insert a joining link and reinstall the chain and the
adjusting nut.
8. Connect the power supply and make a fine adjustment as per the
instructions in 'Setting the spreader length'.
3. Operate the telescopic drive by manually pressing the valves until the
Robalon plate mounting bolts are accessible through the aperture in the
lower flange of the main beam. Replace the plates.
1. Start by removing all the Robalon plates from the ends of telescopic
beams. Leave the plates on the main frame in place.
2. Disconnect the power cables and the hydraulic hoses from the end units.
Seal all hydraulic hoses correctly.
3. Remove the stud from the drawbar connection in the end beam.
4. Take the weight off the end unit using a fork lift truck and extend the unit to
the 40 foot position.
6. Extract the beams from the main frame and inspect them as required.
6. Reassemble the beams and the end units in the reverse order to that in
the instructions above.
NOTE. When replacing the flipper arm motor ensure that the outlet plug is
correctly positioned.
c) Drift out the shaft. Once the shaft has been removed the bearing will be
pushed out by the middle key.
e) Install the parts in the reverse order to dismantle except for that both
bearings have to be drifted into position using a pipe of a suitable bore.
Sensors:
a) Adjust the centre to centre distance Sensor
between twistlocks for each position
by moving the sensors.
Adjusting Key
1. Remove the M6 screw from the top of the twistlock.
2. To lower the twistlock, loosen the twistlock nut
slightly. To raise the twistlock, tighten the nut.
The distance between the top of twistlock head and the Twistlock pin
bottom of guide block 1 -2 mm
3. Recheck the float of the twistlock.
4. Reinstall the M6 screw.
Twistlock
8 of 10 BROMMA CONQUIP AB
head
07 02 ENG
rev. x
Removing the Twistlock Cylinder
1. Make sure the power supply is disconnected
and the oil pressure is relieved from the
system. Split pin
2. Remove the hoses from the cylinder.
3. To avoid oil leakage, thread a plastic bag Spacer
over the end of the hoses and secure
ring
them with straps.
4. Pull out the split pins. Remove the spacer
rings and the cylinder.
Removing Sensors
1. Unscrew the cable connection from
the sensor.
2. Loosen the two screws on the switch
attachment. Signal
3. Remove the sensor. cable
Sensor connection
Installing Sensors
1. Perform the steps above in the reverse
order, using blue Loctite to the cable
connection.
2. The distance between sensor face and
flag is approximately 5-6 mm. Check
the sensor by grabbing the twistlock
head and moving it around in different
positions. If the signal is lost, adjust the
sensor closer to its flag. Make sure the
flag does not come in contact with
the sensor.
Tower Crank
motor
65 Nm
Torque
wrench
•
•
•
•
1
Bromma Manual
331Nm
331Nm
40Nm
331Nm
40Nm
331Nm
Twistlock Twistlock
EH5 / EH170 EH5U / EH170U
100 Nm
95 Nm
91Nm
91 Nm
after 200
test cycles
5
4
3
2
22
21
e
10 20
c 19
b
a 18
17
16
15
14
11 12 13
2
8 Inspection and maintenance of brake BMG 4 and 8
1. Isolate the moto r and brake from the supply, safeguarding them against
un inten tional power -up.
2. Remove the following:
– If fitted, forced- cooling fan for
motor and brake maintenance.
– F lange co ver or fa n guard (21 ).
3. Pu sh the rubber sealing co llar (5) aside.
– R elease the clip to do this, if necessary .
– E xtract the abr aded ma tter.
4. Measure the brake disc (7 ):
If the brak e d isc is:
– ≤ 9 mm on b rake motors up to size 100 .(BMG4)
– ≤ 10 mm on bra ke motor s up to size 1 12.(BMG8)
Fit a new brake disc (→ Section "Ch anging brake disc on BMG 4 and 8
3
Inspection and maintenance of brake BMG 4 and 8 8
1. Iso late the moto r and brake from the supply,, safeguarding them against
un inten tional power -up.
2. Remove the following:
– If fitted, forced coolin g fan
BMG 4 and 8 2
Importan t: This flo ating clerance "s" is necessary so that the pressure plate
can move up as the brake lining wears. Otherwise, reliable braking is not
gu ara nteed.
9. Fit the r ubber sea ling colla r ba ck in place and re-install th e dismantled pa rts.
Note: • T he locka ble man ual brake r elea s e ( type HF) is a lready r elea s ed if a re sistan ce is
encountered whe n ope rating the gr ub scre w.
• T he se lf-reengaging manual b rake re lea s e (type HR) ca n be operated with normal
hand pressu re.
Imp ortant: In brake motors with self-reengaging manual brake release, the
manual brake release lever must be removed after startup/maintenance. A bracket
is provided for storing it on the outside of the motor.
4
8 Inspection and maintenance of brake BMG 4 and 8
Changing Springs
1. Isolate the moto r and brake from the supply, safeguarding them against
un inten tional po wer -up.
2. Remove the following:
– If fitted, fo rced -cooling fan ,
For motor and brake ma intenance .
– F lange cover or fa n guard (21 ), ci rclip (2 0) and fan (19).
3. Remove the ru bber sea ling colla r (5) an d the ma nual brake release:
– s etting nuts (18 ), conical coil sp rings (1 7), studs ( 16) , release le ver ( 15) , dowel
pin (1 4).
4. Unscrew he x nuts ( 10e ), pull o ff the co il body ( 12) .
– B y app rox. 50 mm (watch the bra ke ca ble!) .
5. Cha nge brake springs (11).
– P os ition the bra ke sp rings symme trically.
6. Re- install th e br ake components..
– E xcept fo r the r ubber sea ling colla r, fan an d fan gu ard,
set the wor king air ga p (→ ”Ins pecting brake BMG 4 and 8 setting the
working air gap ” , points 5 th rough 8)
7. With manual brake release: Use setting nuts to s et floating c learance "s" between
the co nical coil springs (pressed fla t) an d the setting nuts ( → following illustration.)
BMG 4 and 8 2
Importan t: This floating clearance "s" is necessary so that the pressure plate
can move up as the brake lining wears. Otherwise, reliable braking is not
gu aranteed.
8. Fit the rubber sealing colla r ba ck in place and re-install th e dismantled pa rts.
Note Fit new settingnuts (18) an d hexag on nuts ( 10e ) if the re moval pr oced ure is r epeated!
5
kVA n
9 f Work done, working air gap, braking torques of brake BMG 4 - 8
i
P Hz
9.3 Work done, working air gap, braking torques of brake BMG 4-8
Workin g air gap
Work do ne Br aking torque se ttings
[mm]
Brak e Fo r until
Br aking Type an d n o. of Order n umber o f
type motor size main tenance
[10 6 J] min. 1) ma x. torque springs spr ings
[N m] Nor mal Red Norma l Red
0.25 0.6
75 6 -
112M
BMG 8 600 0.3 1.2 184 845 3 135 570 8
132S
1)
Please note when checking the air gap:
Parallelism tolerances on the brake disk may give rice to deviation of ±0.1 after
a test run.
6
A ddres s lis t
C o n t a c t y o u r B R O M M A l o c a l r e p r e s e n t a t i v e o r S E W A ddres s es below.
G ermany
Headquarters B ruc hs al S E W-E UR ODR IV E G mbH & C o Tel. (0 72 51) 75-0
P roduc tion E rnst-B lickle-S traß e 42 F ax (0 72 51) 75-19 70
S ales D-76646 B ruchs al http://www.S E W-E UR ODR IV E .de
S ervic e P.O. B ox s ew@ s ew-eurodrive.de
P os tfach 3023 · D-76642 B ruchsal
P roduc tion G raben S E W-E UR ODR IV E G mbH & C o Tel. (0 72 51) 75-0
E rnst-B lickle-S traß e 1 F ax (0 72 51) 75-29 70
D-76676 G raben-Neudorf Telex 7 822 276
P.O. B ox
P os tfach 1220 · D-76671 G raben-Neudorf
A s s embly G arbs en S E W-E UR ODR IV E G mbH & C o Tel. (0 51 37) 87 98-30
S ervic e (near Hannover) Alte R icklinger S traß e 40-42 F ax (0 51 37) 87 98-55
D-30823 G arbs en s cm-garbs en@ s ew-eurodrive.de
P.O. B ox
P os tfach 110453 · D-30804 G arbs en
K irc hheim S E W-E UR ODR IV E G mbH & C o Tel. (0 89) 90 95 52-10
(near München) Domagks traß e 5 F ax (0 89) 90 95 52-50
D-85551 K irchheim s cm-kirchheim@ s ew-eurodrive.de
L angenfeld S E W-E UR ODR IV E G mbH & C o Tel. (0 21 73) 85 07-30
(near Düs s eldorf) S iemens s traß e 1 F ax (0 21 73) 85 07-55
D-40764 Langenfeld s cm-langenfeld@ s ew-eurodrive.de
Meerane S E W-E UR ODR IV E G mbH & C o Tel. (0 37 64) 76 06-0
(near Zwickau) Dänkritzer Weg 1 F ax (0 37 64) 76 06-30
D-08393 Meerane s cm-meerane@ s ew-eurodrive.de
Additional address es for s ervice in G ermany provided on reques t!
F ranc e
P roduc tion Haguenau S E W-US OC OME S AS Tel. 03 88 73 67 00
S ales 48-54, route de S oufflenheim F ax 03 88 73 66 00
S ervic e B . P. 185 http://www.us ocome.com
F -67506 Haguenau C edex s ew@ us ocome.com
A s s embly B ordeaux S E W-US OC OME S AS Tel. 05 57 26 39 00
S ales P arc d’a ctivité s de Magellan F ax 05 57 26 39 09
S ervic e 62, avenue de Magellan - B . P. 182
F -33607 P es s ac C edex
Lyon S E W-US OC OME S AS Tel. 04 72 15 37 00
P arc d’A f faires R oos evelt F ax 04 72 15 37 15
R ue J acques Tati
F -69120 Vaulx en Velin
P aris S E W-US OC OME S AS Tel. 01 64 42 40 80
Zone indus trielle F ax 01 64 42 40 88
2, rue Denis P apin
F -77390 Verneuil I’E t ang
Additional address es for s ervice in F rance provided on reques t!
A rgentina
A s s embly B uenos A ires S E W E UR ODR IV E AR G E NT INA S .A. Tel. (3327) 45 72 84
S ales C entro Indus trial G arin, Lote 35 F ax (3327) 45 72 21
S ervic e R uta P anamericana K m 37,5 s ewar@ s ew-eurodrive.com.ar
1619 G arin
A us tralia
A s s embly Melbourne S E W-E UR ODR IV E P T Y. LT D. Tel. (03) 99 33 10 00
S ales 27 B everage Drive F ax (03) 99 33 10 03
S ervic e Tullamarine, Victoria 3043
S ydney S E W-E UR ODR IV E P T Y. LT D. Tel. (02) 97 25 99 00
9, S leigh P lace, Wetherill P ark F ax (02) 97 25 99 05
New S outh Wales , 2164
A us tria
A s s embly Wien S E W-E UR ODR IV E G es .m.b.H. Tel. (01) 6 17 55 00-0
S ales R ichard-S traus s -S tras s e 24 F ax (01) 6 17 55 00-30
S ervic e A-1230 Wien s ew@ s ew-eurodrive.at
7
Address list
Belgium
Assembly Brüssel CARON-VECTOR S.A. Tel. (010) 23 13 11
Sales Avenue Eiffel 5 Fax (010) 2313 36
Service B-1300 Wavre http://www.caron-vector.be
info@caron-vector.be
Brazil
Production Sao Paulo SEW DO BRASIL Tel. (011) 64 60-64 33
Sales Motores-Redutores Ltda. Fax (011) 64 80 33 28
Service Rodovia Presidente Dutra, km 208 sew@sew.com.br
CEP 07210-000 - Guarulhos - SP
Additional addresses for service in Brazil provided on request!
Bulgaria
Sales Sofia BEVER-DRIVE GMBH Tel. (92) 9 53 25 65
Bogdanovetz Str.1 Fax (92) 9 54 93 45
BG-1606 Sofia bever@mbox.infotel.bg
Canada
Assembly Toronto SEW-EURODRIVE CO. OF CANADA LTD. Tel. (905) 7 91-15 53
Sales 210 Walker Drive Fax (905) 7 91-29 99
Service Bramalea, Ontario L6T3W1 www.sew-eurodrive.ca
Vancouver SEW-EURODRIVE CO. OF CANADA LTD. Tel. (604) 9 46-55 35
7188 Honeyman Street Fax (604) 946-2513
Delta. B.C. V4G 1 E2
Montreal SEW-EURODRIVE CO. OF CANADA LTD. Tel. (514) 3 67-11 24
2555 Rue Leger Street Fax (514) 3 67-36 77
LaSalle, Quebec H8N 2V9
Additional addresses for service in Canada provided on request!
Chile
Assembly Santiago de SEW-EURODRIVE CHILE Tel. (02) 6 23 82 03+6 23 81 63
Sales Chile Motores-Reductores LTDA. Fax (02) 6 23 81 79
Service Panamericana Norte No 9261
Casilla 23 - Correo Quilicura
RCH-Santiago de Chile
China
Production Tianjin SEW-EURODRIVE (Tianjin) Co., Ltd. Tel. (022) 25 32 26 12
Assembly No. 46, 7th Avenue, TEDA Fax (022) 25 32 26 11
Sales Tianjin 300457
Service
Colombia
Assembly Bogotá SEW-EURODRIVE COLOMBIA LTDA. Tel. (0571) 5 47 50 50
Sales Calle 22 No. 132-60 Fax (0571) 5 47 50 44
Service Bodega 6, Manzana B sewcol@andinet.com
Santafé de Bogotá
Croatia
Sales Zagreb KOMPEKS d. o. o. Tel. +385 14 61 31 58
Service PIT Erdödy 4 II Fax +385 14 61 31 58
HR 10 000 Zagreb
Czech Republic
Sales Praha SEW-EURODRIVE S.R.O. Tel. 02/20 12 12 34 + 20 12 12 36
Business Centrum Praha Fax 02/20 12 12 37
Luná 591 sew@sew-eurodrive.cz
16000 Praha 6
Denmark
Assembly Kopenhagen SEW-EURODRIVEA/S Tel. 4395 8500
Sales Geminivej 28-30, P.O. Box 100 Fax 4395 8509
Service DK-2670 Greve http://www.sew-eurodrive.dk
sew@sew-eurodrive.dk
Estonia
Sales Tallin ALAS-KUUL AS Tel. 6 59 32 30
Paldiski mnt.125 Fax 6 59 32 31
EE 0006 Tallin
8
Address list
Finland
Assembly Lahti SEW-EURODRIVE OY Tel. (3) 589 300
Sales Vesimäentie 4 Fax (3) 780 6211
Service FIN-15860 Hollola 2
Great Britain
Assembly Normanton SEW-EURODRIVE Ltd. Tel. 19 24 89 38 55
Sales Beckbridge Industrial Estate Fax 19 24 89 37 02
Service P.O. Box No.1
GB-Normanton, West- Yorkshire WF6 1QR
Greece
Sales Athen Christ. Boznos & Son S.A. Tel. 14 22 51 34
Service 12, Mavromichali Street Fax 14 22 51 59
P.O. Box 80136, GR-18545 Piraeus Boznos@otenet.gr
Hong Kong
Assembly Hong Kong SEW-EURODRIVE LTD. Tel. 2-7 96 04 77 + 79 60 46 54
Sales Unit No. 801-806, 8th Floor Fax 2-7 95-91 29
Service Hong Leong Industrial Complex sew@sewhk.com
No. 4, Wang Kwong Road
Kowloon, Hong Kong
Hungary
Sales Budapest SEW-EURODRIVE Kft. Tel. +36 1 437 06 58
Service H-1037 Budapest Fax +36 1 437 06 50
Kunigunda u. 18
India
Assembly Baroda SEW-EURODRIVE India Pvt. Ltd. Tel. 0 265-83 10 86
Sales Plot No. 4, Gidc Fax 0 265-83 10 87
Service Por Ramangamdi · Baroda - 391 243 sew.baroda@gecsl.com
Gujarat
Ireland
Sales Dublin Alperton Engineering Ltd. Tel. (01) 8 30 62 77
Service 48 Moyle Road Fax (01) 8 30 64 58
Dublin Industrial Estate
Glasnevin, Dublin 11
Italy
Assembly Milano SEW-EURODRIVE di R. Blickle & Co.s.a.s. Tel. (02) 96 98 01
Sales Via Bernini,14 Fax (02) 96 79 97 81
Service I-20020 Solaro (Milano)
Japan
Assembly Toyoda-cho SEW-EURODRIVE JAPAN CO., LTD Tel. (0 53 83) 7 3811-13
Sales 250-1, Shimoman-no, Fax (0 53 83) 7 3814
Service Toyoda-cho, Iwata gun
Shizuoka prefecture, P.O. Box 438-0818
Korea
Assembly Ansan-City SEW-EURODRIVE KOREA CO., LTD. Tel. (031) 4 92-80 51
Sales B 601-4, Banweol Industrial Estate Fax (031) 4 92-80 56
Service Unit 1048-4, Shingil-Dong master@sew-korea.co.kr
Ansan 425-120
Luxembourg
Assembly Brüssel CARON-VECTOR S.A. Tel. (010) 23 13 11
Sales Avenue Eiffel 5 Fax (010) 2313 36
Service B-1300 Wavre http://www.caron-vector.be
info@caron-vector.be
Macedonia
Sales Skopje SGS-Skopje / Macedonia Tel. (0991) 38 43 90
"Teodosij Sinactaski” Fax (0991) 38 43 90
6691000 Skopje / Macedonia
Malaysia
Assembly Johore SEW-EURODRIVE SDN BHD Tel. (07) 3 54 57 07 + 3 54 94 09
Sales No. 95, Jalan Seroja 39, Taman Johor Jaya Fax (07) 3 5414 04
Service 81000 Johor Bahru, Johor
West Malaysia
9
Address list
Netherlands
Assembly Rotterdam VECTOR Aandrijftechniek B.V. Tel. +31 10 44 63 700
Sales Industrieweg 175 Fax +31 10 41 55 552
Service NL-3044 AS Rotterdam http://www.vector.nu
Postbus 10085 info@vector.nu
NL-3004 AB Rotterdam
New Zealand
Assembly Auckland SEW-EURODRIVE NEW ZEALAND LTD. Tel. 0064-9-2 74 56 27
Sales P.O. Box 58-428 Fax 0064-9-2 74 01 65
Service 82 Greenmount drive sales@sew-eurodrive.co.za
East Tamaki Auckland
Christchurch SEW-EURODRIVE NEW ZEALAND LTD. Tel. 0064-3-3 84 62 51
10 Settlers Crescent, Ferrymead Fax 0064-3-3 85 64 55
Christchurch sales@sew-eurodrive.co.nz
Norway
Assembly Moss SEW-EURODRIVE A/S Tel. (69) 2410 20
Sales Solgaard skog 71 Fax (69) 2410 40
Service N-1599 Moss sew@sew-eurodrive.no
Peru
Assembly Lima SEW DEL PERU MOTORES REDUCTORES Tel. (511) 349-52 80
Sales S.A.C. Fax (511) 349-30 02
Service Los Calderos # 120-124 sewperu@terra.com.pe
Urbanizacion Industrial Vulcano, ATE, Lima
Poland
Sales Lodz SEW-EURODRIVE Polska Sp.z.o.o. Tel. (042) 6 16 22 00
ul. Pojezierska 63 Fax (042) 6 16 22 10
91-338 Lodz sew@sew-eurodrive.pl
Portugal
Assembly Coimbra SEW-EURODRIVE, LDA. Tel. (0231) 20 96 70
Sales Apartado 15 Fax (0231) 20 36 85
Service P-3050-901 Mealhada infosew@sew-eurodrive.pt
Romania
Sales Bucuresti Sialco Trading SRL Tel. (01) 2 30 13 28
Service str. Madrid nr.4 Fax (01) 2 30 71 70
71222 Bucuresti sialco@mediasat.ro
Russia
Sales St. Petersburg ZAO SEW-EURODRIVE Tel. (812) 3 26 09 41 + 5 35 04 30
P.O. Box 193 Fax (812) 5 35 22 87
193015 St. Petersburg sew@sew-eurodrive.ru
Singapore
Assembly SEW-EURODRIVE PTE. LTD. Tel. 8 62 17 01-705
Sales No 9, Tuas Drive 2 Fax 8 61 28 27
Service Jurong Industrial Estate Telex 38 659
Singapore 638644
Slovenia
Sales Celje Pakman - Pogonska Tehnika d.o.o. Tel. 00386 3 490 83 20
Service UI. XIV. divizije 14 Fax 00386 3 490 83 21
SLO – 3000 Celje pakman@siol.net
10
Address list
South Africa
Assembly Johannesburg SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. + 27 11 248 70 00
Sales Eurodrive House Fax +27 11 494 23 11
Service Cnr. Adcock Ingram and Aerodrome Roads ljansen@sew.co.za
Aeroton Ext. 2
Johannesburg 2013
P.O.Box 90004
Bertsham 2013
Capetown SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 21 552 98 20
Rainbow Park Fax +27 21 552 98 30
Cnr. Racecourse & Omuramba Road Telex 576 062
Montague Gardens
Cape Town
P.O.Box 36556
Chempet 7442
Cape Town
Durban SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 31 700 34 51
2 Monaceo Place Fax +27 31 700 38 47
Pinetown
Durban
P.O. Box 10433, Ashwood 3605
Spain
Assembly Bilbao SEW-EURODRIVE ESPAÑA, S.L. Tel. 9 44 31 84 70
Sales Parque Tecnológico, Edificio, 302 Fax 9 44 31 84 71
Service E-48170 Zamudio (Vizcaya) sew.spain@sew-eurodrive.es
Sweden
Assembly Jönköping SEW-EURODRIVE AB Tel. (036) 34 42 00
Sales Gnejsvägen 6-8 Fax (036) 34 42 80
Service S-55303 Jönköping www.sew-eurodrive.se
Box 3100 S-55003 Jönköping
Switzerland
Assembly Basel Alfred lmhof A.G. Tel. (061) 4 17 17 17
Sales Jurastrasse 10 Fax (061) 4 17 17 00
Service CH-4142 Münchenstein bei Basel http://www.imhof-sew.ch
info@imhof-sew.ch
Thailand
Assembly Chon Buri SEW-EURODRIVE (Thailand) Ltd. Tel. 0066-38 21 40 22
Sales Bangpakong Industrial Park 2 Fax 0066-38 21 45 31
Service 700/456, Moo.7, Tambol Donhuaroh sewthailand@sew-eurodrive.co.th
Muang District
Chon Buri 20000
Turkey
Assembly Istanbul SEW-EURODRIVE Tel. (0216) 4 41 91 63 + 4 41 91 64 + 3
Sales Hareket Sistemleri San. ve Tic. Ltd. Sti 83 80 14 + 3 83 80 15
Service Bagdat Cad. Koruma Cikmazi No. 3 Fax (0216) 3 05 58 67
TR-81540 Maltepe ISTANBUL seweurodrive@superonline.com.tr
USA
Production Greenville SEW-EURODRIVE INC. Tel. (864) 4 39 75 37
Assembly 1295 Old Spartanburg Highway Fax Sales (864) 439-78 30
Sales P.O. Box 518 Fax Manuf. (864) 4 39-99 48
Service Lyman, S.C. 29365 Fax Ass. (864) 4 39-05 66
Telex 805 550
Assembly San Francisco SEW-EURODRIVE INC. Tel. (510) 4 87-35 60
Sales 30599 San Antonio St. Fax (510) 4 87-63 81
Service Hayward, California 94544-7101
Philadelphia/PA SEW-EURODRIVE INC. Tel. (856) 4 67-22 77
Pureland Ind. Complex Fax (856) 8 45-31 79
200 High Hill Road, P.O. Box 481
Bridgeport, New Jersey 08014
Dayton SEW-EURODRIVE INC. Tel. (9 37) 3 35-00 36
2001 West Main Street Fax (9 37) 4 40-37 99
Troy, Ohio 45373
Dallas SEW-EURODRIVE INC. Tel. (214) 3 30-48 24
3950 Platinum Way Fax (214) 3 30-47 24
Dallas, Texas 75237
11
Address list
USA
Additional addresses for service in the USA provided on request!
Venezuela
Assembly Valencia SEW-EURODRIVE Venezuela S.A. Tel. +58 (241) 8 32 98 04
Sales Av. Norte Sur No. 3, Galpon 84-319 Fax +58 (241) 8 38 62 75
Service Zona Industrial Municipal Norte sewventas@cantr.net
Valencia sewfinanzas@cantr.net
12
Bromma Group Manual
0-1-may 02 rev.00 Bromma Conquip
8 • Spare parts and service
215
3778
1891
1040
240
13
Control box
185
A
4x Overheight lug
5852 (20' ISO)
8918 (30' ISO)
11984 (40' ISO) 106
TTDS
2x Panel, 4x LED signal lamp
Color refer to electrical diagram
1055
B
B
1500 1x Ladder a
4
1335
3 2
1306
1314
556
1187
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
- - - -
100
BR1256227
Number Row Order Position Number Quantity Title (Item,CO) Revision
Latest Obsolete
State (Historical)Vault
On/Off
Status
BOM Row
13
D ( 1 : 10 )
150
80
FOR POSITION MARKING INSTRUCTIONS
SEE REFERENCE DOCUMENT:
5000036 (TBU, FRAME) 11
C-C ( 1 : 20 )
7 a
5 7 13 1 C
A Gear Side Pulley side 2 4
15
80 3
80
80
40
46
B
(152,4)
on electrical motor.
G ( 1 : 10 )
170
G D
200
100
50
180 25
A 16
1364
a 10
10
6
12
Warning sign for el. voltage
12 F F
to be attached on el. cabinet.
WHITE FLIPPER
BLACK FLIPPER
RAL 9016
RAL 9005
A-A ( 1 : 20 )
F-F ( 1 : 10 )
9 8 Rotated
6
SWL-sign ordered with safe working load type
of spreader and manufacturing year engraved:
engravment colored black.
Weight to be stamped on SWL - sign.
BR1256228
41
15
TWIN LIFT 2x25
5
EH170U
5
Made in Malaysia
5
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
- - - -
DATE MATERIAL SHEET WEIGHT TOLERANCE GENERAL
mdyazmu SPREADER A3 - a
WITH DECORATION, EH170U DRAWING NUMBER
BR1256228
Number Row Order Position Number Quantity Title (Item,CO) Revision
Latest Obsolete
State (Historical)Vault
On/Off
Status
BOM Row
A(1:5)
9
10
3
11
15
13
29
12 6 32 18
28 32
19
24
25
14 22 20
8 38
1 26
21 36
31
4 39
34 17
B
40 27
37
A
33
5
16 23 35 B(1:8)
30
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
- - - -
DATE MATERIAL SHEET WEIGHT TOLERANCE GENERAL
BR1256229
Number Row Order Position Number Quantity Title (Item,CO) Revision
Latest Obsolete
State (Historical)Vault
On/Off
Status
BOM Row
13
14
D(1:5)
A A
5
a
THIS DRAWING IS COPYRIGHT AND IS PROPERTY OF BROMMA CONQUIP. THE DESIGN AND/OR CONSTRUCTIONS CONTAINED THEREIN MAY NOT BE
4
b
15
c
6 (see Note A)
9 2 8
TWISTLOCK ADJUST INSTRUCTION
NOTE A:
SENSOR FOR LANDED SHALL INDICATE LANDED 0 TO 6mm.
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
BR1235912
Number Row Order Position Number Quantity Title (Item,CO) Revision
Latest Obsolete
State (Historical)Vault
On/Off
Status
BOM Row
B-B ( 1 : 20 )
7
16
10 9 15 10 A-A ( 1 : 20 )
8
A
1
21
THIS DRAWING IS COPYRIGHT AND IS PROPERTY OF BROMMA CONQUIP. THE DESIGN AND/OR CONSTRUCTIONS CONTAINED THEREIN MAY NOT BE
A
a
20
C ( 1 : 10 )
18
2
13
11 17
14
COPIED OR REPRODUCED WITHOUT THE WRITTEN CONSENT OF THE OWNER.
B B
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
19 12 3 5 10 9 4 6 3 - - - -
DATE MATERIAL SHEET WEIGHT TOLERANCE GENERAL
BR1256230
Number Row Order Position Number Quantity Title (Item,CO) Revision
Latest Obsolete
State (Historical)Vault
On/Off
Status
BOM Row
CRANE CABLE
4
B-B ( 1 : 10 )
B
A A 12 9 10 14
B
13
A-A ( 1 : 10 )
11
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
- - - -
DATE MATERIAL SHEET WEIGHT TOLERANCE GENERAL
BR1237620
Number Row Order Position Number Quantity Title (Item,CO) Revision
Latest Obsolete
State (Historical)Vault
On/Off
Status
BOM Row
12 13 1 2 6 10
CONSENT OF THE OWNER.
5 9 4 3 14 7
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
DESIGNED TREATMENT SS-ISO 2768
Illtek 021029 EH5
PLOT DATE
SCALE REVISION
Spreader EH5 01
ARTICLE No
E DRAWING NUMBER
General assy
A Partek Company
SP-52000
THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY
48
3 33 47 4 32
CONSENT OF THE OWNER.
1 49
35
36
37 50
16 20
26 34 17 10 21 14
7
39
43
38
8
39
9
2
24
15
29
11 23
5 43
6 44
38
22 43 44 20 38
28 43
41
18
38
12 43
31 46
25 39
40 38 36 43 42
30 19
38
43
39
45 27
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED
Illtek 021029 EH5
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Tower DRAWING NUMBER
A Partek Company
SP-52001
EH5 Tower New standard
DRAWING SP-52001
PART NO DESCRIPTION QTY POS REMARKS
24161 TOWER 1 1
Method
The following steps need to be taken to ensure that all parts are
secured properly on the spreader:
2 Insert the Lifting Shaft carefully. Ensure that the shaft and
holes have been adequately greased.
3 Insert the Locking Shaft through the lock hole from the top
to bottom.
Note!
It is not possible to insert the
shaft from underneath!!
4 Secure all the chains to the shackles, as described in the
instructions below:
i Chain C1 (L=425) to attach to Shackle a & b.
ii Chain C2 (L=284) to attach to Shackle d & b.
Note!
Chain C2 must be secured tightly as it functions
as a secondary safety feature, after the Lock
Shaft has been removed!
2016-05
1 Rev. 02 Bromma 2
Bromma Manual
5 All shackles will then be attached to the Lock Shaft (a), Eye
Lug on the tower frame (b) & (e), Locking Pin (c) and Lifting
Shaft (d), respectively.
14 11 35 10 33 34 39 36 43 4
CONSENT OF THE OWNER.
20
12
19 25
18
29 8
45 24
23
22
40 9
32 13
21
1 12 6
26
13
7 12
44 15
5
2 41
3
31 42
38
48 27
47
17 37 28 30 46 16
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 021002 EH5 ll
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Tower gear box assy DRAWING NUMBER
A Partek Company
SP-52002
EH5 Tower Gearbox Assy
DRAWING SP-52002
PART NO DESCRIPTION QTY POS REMARKS
58549 GEARBOX R97 ELM.BRAKE 360-404V 1 1 Part no for gearbox is 72157 and for only El motor is 58538
48188 DISTANS 4 13
71549 DISTANCE 4 19
44769 WASHER 1 44
13
7
15 14
CONSENT OF THE OWNER.
16
32
25
8 26
36
37
22
24
18 33
5 21
23 35
31
20 10 2
4 19 34
12 11
3
29
17
6 28
30
27
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 020903 EH5
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Frame DRAWING NUMBER
A Partek Company
SP-52003
EH5 Frame
DRAWING SP-52003
PART NO DESCRIPTION QTY POS REMARKS
16997 FRAME 1 1
401278 GLIDE PLATE FRAME 2 3 Included in Glide plate assy See drawing SP-52004
47805 PLATE 1 10
38865 COVER 1 12
401281 SHIM 2 17
49853 SLEEV 2 26
401280 20´BUFFER 1 28
401276 BUFFER 1 36
17
19 25 16
15
18
2
10
11 9
13
20
12 3
24
15
14
10
22
21
23 1
6
5
7
8
4
6
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 021002 EH5 ll
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Telescopic Beam DRAWING NUMBER
A Partek Company
SP-52004
EH5 Telescopic Beam
DRAWING SP-52004
PART NO DESCRIPTION QTY POS REMARKS
38861 GLIDE PLATE ASSY 2 0 Include pos. 4,5,6,7,8 and pos 3 on drawing SP-52003
24142 TELESCOPIC BEAM ASSY 1 1 Assy with 2 Beams and 1 Gable end
62595 FLIPPER ARM 1 2 Please note! Rubber buffer not included, see item 11
24168 FLIPPER ARM 1 3 Please note! Rubber buffer not included, see item 11
24167 FLIPPER ARM 1 9 Please note! Rubber buffer not included, see item 11
15
CONSENT OF THE OWNER.
2 3 38 53 54 55 231
47 10 13 12 16 17 59 19 58 40 41 23 65 37
4
34
57 49
35
33 32
56 42
43 7
24
45 61 18 14 51 14 25 28 22
11 39
44
31
62 60 20 28 29 30
46
8 9 74 63
27
26
36
71
68
72
67 73
52
64
69
69 70 66 65 70
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 020926 EH5
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Hydraulic Assy End beam DRAWING NUMBER
A Partek Company
SP-52005
EH5 Hydraulic Assy
DRAWING SP-52005
PART NO DESCRIPTION QTY POS REMARKS
76196 HYDRAULIC MOTOR INCL.CHOCKVALV 300CC 3 9 SEE DRAWING SP-52009 FOR MORE DETAILS
71320 HYDRAULIC PUMP PVQ10 1 18 WHEN YOU ORDER SEAL KIT FOR THIS PUMP PLEASE STATE K4264
73096 VALVE DG4V-3-2C-MU-H7-60 4 23 WHEN YOU ORDER SEAL KIT PLEASE STATE PART NO K4222 AND SOLENOID 70422
401400 FLATBAR 1 65
401399 FLAP 1 66
8 6 5 2 7 18
26
25
1 7 4 5 7 3 9 10 13 15 16
12
11
23
22
19 20 14
24 17
21
28
27
30 29
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 020910 EH5
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Telescopic Gearbox Assy DRAWING NUMBER
A Partek Company
SP-52006
EH5 Telescopic Gearbox Assy
DRAWING SP-52006
PART NO DESCRIPTION QTY POS REMARKS
53596 SHAFT 1 1
53603 DISTANCE 1 2
53604 DISTANCE 1 3
53605 DISTANCE 1 4
53595 COVER 1 8
53594 COVER 1 9
401287 PLATE 1 20
6
7
9
13
10
CONSENT OF THE OWNER.
3 4
S*
5
2
1
8
10
10
11 12
6
9
7
10 13
15
4
S*
5
2
1
8
10
10 12
11
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 020926 EH5 ll
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Sensor Assy DRAWING NUMBER
A Partek Company
SP-52008
Single Sensor Assy Part no 38084 SP-52008
Pos Part no Description Qty Remarks
0 38084 SENSOR SINGEL ASSY 0 Include pos.2,3,4,5,6,7,8,9,10,11,12,13
2 400267 PLATE 1
2 400267 PLATE 2
9
19
16
3
17
1
13
15
20 12
21 7
5
10 6
22
8
2
19
18 11 6 4
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 021029 EH5 ll
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Gearbox DRAWING NUMBER
A Partek Company
SP-52009
EH5 Flipper Gearbox Assy Part no 53275
DRAWING SP-52009
PART NO DESCRIPTION QTY POS REMARKS
60629 GEAR BOX ASSY TYPE 2 1 0 Include pos.1-8,11-12,15,17-20 ( Pos.3 Mirrow inverted)
56230 GEAR BOX ASSY TYPE 2 1 0 Include pos.1-8,11-12,15-18 ( Pos.3 Mirrow inverted)
2
CONSENT OF THE OWNER.
35
9 36 52
33 53
34 47
39
46
42
43
45 14
44
48
41
7 54
40
3 28
37 29
38 27
25 8
30
31
32
26
13
1 48
49
50 5
51
10 11 15 16
4
23 18 22 17 20 21 24 19
12
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 020911 EH5
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Telescopic Drive DRAWING NUMBER
A Partek Company
SP-52012
EH5 Telescopic Drive
DRAWING SP-52012
PART NO DESCRIPTION QTY POS REMARKS
16441 TELESCOPIC DRIVE ATT. ASSY 1 2 See Telescopic assy Drawing SP-52006
1
A
A-A ( 1 : 2 )
9 6 2 4 3
7 10 5 8
A
THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY OF BROMMA CONQUIP AB. THE DESIGN AN OR CONSTRUCTIONS CONTAINED THEREIN MAY NOT BE
COPIED OR REPRODUCED WITHOUT THE WRITTEN CONSENT OF THE OWNER.
1018972
Number Detail ID Quantity Title (Item,CO) Description (Item,CO) Revision
BR1018967 - - CABINET X100 C/C 430x150 c
BR1018159 1 1 DOOR ASSEMBLY X100 c
BR76460 2 4 NUT LOC-KING M8 A4, DIN 985, KLASS 70 -
BR1018174 3 1 ELECTRICAL BOX WELD ASSEMBLY g
BR1008258 4 2 VALVE - -
BR1020746 5 2 LOCKING DEVICE Bednorz, 800-VH-NA-NR -
BR1020637 6 2 LOCKING DEVICE Bednorz, 800-18-C-NR -
BR1022661 7 1 RUBBER COVER X100 a
BR77851 8 2 SCREW M6S 8x25 A4, CLASS 70 -
BR1000742 9 2 WASHER A4-RBS 8,4 KLASS 70 -
REV DESCRIPTION ECO-No. DATE BY
RUBBER COVER ADDED
a Value 2008-09-30 PON
AND MOUNTING PARTS
b matrix update Value 2008-10-13 PON
MOUNTING PARTS FOR
c Value 2009-02-04 PON
RUBBER COVER CHANGED
A
1
A-A
6
B
2
A
a c 3
B (2:1)
7 8 9 2
THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY OF BROMMA CONQUIP AB. THE DESIGN AN OR CONSTRUCTIONS CONTAINED THEREIN MAY NOT BE
5
COPIED OR REPRODUCED WITHOUT THE WRITTEN CONSENT OF THE OWNER.
CABINET X100 A2 c
C/C 430x150 DRAWING NUMBER
1018967
Number Detail ID Quantity Title (Item,CO) Description (Item,CO) Revision
BR1018972 - - CABINET X100 MOBILE SPREADER C/C 430x150 c
BR1018967 1 1 CABINET X100 C/C 430x150 c
BR1018235 2 1 MOUNTING PLATE ASSY JIB SPREADER -
BR1000657 3 6 SCREW MC6S M8x16 A4 KLASS 70 -
BR701437 4 6 WASHER NORD-LOCK M8 A4 -
BR701016 5 14 GLAND MS-M16 4.5-10mm M16x1.5 -
BR701018 6 1 GLAND MS-M25 9-17mm M25x1.5 -
BR701019 7 1 GLAND MS-M32 11-21mm M32x1.5 -
BR1001909 8 14 Electrical component Gland nut M16/ Skindicht -
BR1001911 9 1 Electrical component Gland nut M25/ Skindicht -
BR1001912 10 1 Electrical component Gland nut M32/ Skindicht -
THIS DRAWING IS COPYRIGHT AND IS THE PROPERTY
21 23 22 6 7 9
13
30
12
27
8 26
17 11
19
18 28
20
3
14
16
4
15
24
10 5
2 25
32 31 35 34 33 1 29
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 031013 EH170 U
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Twinlift boxes DRAWING NUMBER
A Partek Company
SP-52014
17652 Twin Housing Assy
SP-DRAWING NO: 52014
SP-POS PART NO DESCRIPTION QTY REMARKS NOTE
12 402534 SPACER 2
14 29 28 23 24 26 2
CONSENT OF THE OWNER.
1
12
17 27 25
21 29
11
S*
13
20
15
30
6
19
25
26 18 8
24
23 10 16
22
5
31
S*
9 7
SIGN DATE GENERAL ASSY SERIAL No SPREADER TYPE SURFACE TOLERANCE GENERAL
TREATMENT SS-ISO 2768
DESIGNED Illtek 031027 EH170 U
PLOT DATE
SCALE REVISION
Exploded View
ARTICLE No
E
Retractable Twistlock Assembly DRAWING NUMBER
A Partek Company
SP-52015
62907 Twin Twistlock Assy Right
SP-DRAWING NO: 52015
SP-POS PART NO DESCRIPTION QTY REMARKS NOTE
BGS Accessories
8.15 LED signal lamps
Application
Bromma telescopic spreaders can be equipped with LED
signal lamps to inform the crane driver and other personnel if
the sprader has landed, (white or yellow), is unlocked (green)
or has locked (red) on a container. For twinlift spreaders a
fourth lamp is used to indicate twinboxes down (blue). For
mobile harbour crane spreaders the fourth lamp indicates
- Low power consumption tower in mid position (yellow).
Available models
LED Colors voltage Art. No. Rec. cable
Green, red, yellow 24 VDC 1001399
Technical specifications
Model 24VDC 110/230VAC
Dimensions
Light
aspects A (mm) B (mm)
1 160 130
2 305 275
3 450 420
4 595 565
Spare parts
SP-POS PART NO. DESCRIPTION QTY REMARKS
1 75102 Screw M6S 8x30 4 FZB 8.8
2 75328 Washer BRB 8,4x16x1,5 8 FZB HB2
3 75090 Nut M8 LOC-KING 4 FZB
4 see page 1
5 1001415 Attachment stright 2 per LED
6 1002903 Attachment tilted 300 2 per LED
70396 Cable 10m for 24VDC
Warnings
CAUTION: LED light units are sources of bright light. Do
not stare directly into the beam from close distances and
observe all the warnings and guidelines in the instruction
manual. Bromma LED indicator panels are classified as
Class 2M LED devices according to the standard
IEC60825-1:1993+A1:1997+A2:2001.
1
THIS DRAWING IS COPYRIGHT AND IS PROPERTY OF BROMMA CONQUIP. THE DESIGN AND/OR CONSTRUCTIONS CONTAINED THEREIN MAY NOT BE
RAW MATERIAL ART.NR RAW MATERIAL PROFILE DIMENSION AND TOLERANCE RAW MATERIAL TYPE
BR1001444
Number Detail ID Quantity Title (Item,CO) Description (Item,CO) Revision
BR1001444 - - LED ASSEMBLY 4 LEDS a
BR75102 1 4 SCREW M6S 8x30 FZB 8.8 ISO 4017 -
BR75328 2 8 WASHER BRB 8,4x16x1,5 FZB, SMS 70 -
BR75090 3 4 NUT LOC-KING M8 DIN 985, FZB, CLASS 8 a
• How to order spare parts and/or service
All ordering of Bromma spare parts must be done by the Bromma e-commerce
website. To order the requested spare parts some important information must be
available.
The serial no. of the spreader. See Data Sheet chapt. 3or the dataplate mounted on
main frame of the current spreader.
The requested Art no. and the quantity needed. See Spare part list.
Registered User
To be able to log in at the Bromma e-commerce site you must be a registered user.
To become a registered user you have to fill in the Application Form on the Bromma
website. After a few days you will receive an User ID and a password by e-mail.
When you are a regitered user fill in your User ID and password at the fields on the
Bromma e-commerce website (www.bromma.com) to log in. Then follow the
instructions on the screen.
Search Function
If you do not find the parts requested on the e-commerce site or if you have any other
problems finding valid part numbers you can use the search function on the website
or call your local Bromma dealer. The phone number is published on the website
at www.bromma.com
F26_001_V3.22
A A
B B
C C
Created on 31/10/2016
E Edit date 25/10/2019 by (short name) ZAMZUMO Number of pages 108 E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F28_001_PS
A A
Color coding according to EN 60204-32
Power supply specification
L3 Black
N n/a
PE Green / Yellow
C C
Control circuits
AC CURRENT Red
PE Green / Yellow
E Cable sections E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A Higher-level function Mounting location Page Page description Supplementary page field Date Edited by A
A1
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A Higher-level function Mounting location Page Page description Supplementary page field Date Edited by A
A1
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A Higher-level function Mounting location Page Page description Supplementary page field Date Edited by A
A1
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A Higher-level function Mounting location Page Page description Supplementary page field Date Edited by A
A1
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Revision overview F17_002_V2
Revision name c
A A
Reason for revision change Page name Revision description Creator Date
Revision name b
Reason for revision change Page name Revision description Creator Date
Revision name a
Reason for revision change Page name Revision description Creator Date
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
L1.1 / 31.1:A
L2.1 / 31.1:A
A A
L3.1 / 31.1:A
1 3 5 1 3 5 95 97
B -K1 -QM6 B
/55.3:E 2 4 6 8 Amp 96 98
Main contactor
I> I> I>
2 4 6
7
-XP22 1 2 3 22
/31.2:C
WARNING 1 2 3 22
-XP23
/31.2:C
Interlock signals from crane & heaters are not disconnected -WXP23
via main breaker on the spreader. /31.3:C 1 2 3 20
Disconnect the electrical plug from spreader for safe working practice.
D +X100 D
-X3 32 33 34 PE
-X2 L1 L1 L2 L2 L3 L3
+X0-WXP1 +X0
37G2.5 22 30 23 31 24 32 -WMA3 1 2 3 GNYE
U1 V1 W1
+X0-UC1
E E
Plug Power Power M
-XP1 30
Supply L2
31
Supply L3
32 -MA3
Power 400VAC 3~
Supply L1 4.0 kW / 50 Hz
Delta connection PE
Center Hydraulic Pump
Power Power
-XP1 Supply L2
23
Supply L3
24
Power 22 -MA3
Supply L1
Center Hydraulic Pump
Supply from costumer 400V 3~/PE AC 50 Hz
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
1 3 5
-QM8
5.5 Amp
B B
1 3 5 1 3 5
-K8 -K9
/50.7:C 2 4 6 2 4 6
C 6 C
-XP22 7 8 9 21
-XP23 7 8 9 21
+X1
-WXP23 7 8 9 22
+X100
-X3 38 39 40 PE
D -WMA4 1 2 3 GNYE D
-MA4
Star connection
U1 V1 W1
Current relay
-KA70 Brake
WH WH RD RD -QL4
WH WH. BU BU
E E
BU BU
W2 U2 V2
WH WH RD
400VAC M
3.0 kW / 50 Hz -MA4
Telerscopic motor
3~ Telescopic motor
RD
main frame
PE main frame
-BGE 1 2 3 4 5
Brake control
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
1 3 5
-QM1
14 Amp
B B
1 3 5 1 3 5
-K2 -K3
/50.5:C BK BK 2,5 mm²
2 4 6 2 4 6
1
-FC1
2A
C 2 C
-X2 1 2 3
7 -P2 h
2
+X0
D -WMA1 1 2 3 GN/YE D
-MA1
Star connection
U1 V1 W1
Current relay
-KA71 Brake
WH WH RD RD -QL4
WH WH. BU BU
E E
BU BU
W2 U2 V2
WH WH RD
400VAC M
5,5 kW / 50 Hz
Gravity point motor
3~ RD
Hour counter
PE
-MA1 -BGE 1 2 3 4 5
Gravity point motor Brake control
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X0-UC1
Plug
-XP1 1 25 3
/30.0:E Control Voltage 230VAC Control Voltage 230VN Spreader Pilot N
A A
+X0-WXP1
37G2.5 1 25 3
-X2 108
106 105 107
11.
2,5 mm²
-SS1
/55.3:B 12.
B 13 B
-QA1
/30.1:C 14
NOTE:
1 3
All 24 V DC supply should be ring connected &
-FC2
MCB 10A 2 4
wire for 24 V DC shall be 2,5mm² with blue colour.
230 VN
51.1:D
-X2 L L N N
230 VAC
49.0:B
C C
BN BU GNYE
4
-TA1
+X0/220.3:D L N PE
24VDC/20A pri. 100...120 V AC
Power supply 200...240 V AC
Blade terminal fuse
ZB0807 3B1 / +X0/60.1:F
PSU-1AC/24VDC-20A 1B1 / +X0/60.1:E
+X0 2B1 / +X0/60.1:E
On Tower sec. 24...28 V DC Fuse 5A
- - + + -X1
1a
-PE10 1
B1+
-X1
D D
2,5 mm² 2,5 mm²
BK BK
2,5 mm²
Note: The Grounding Cable Connection RD Fuse 30A
should be connected from
Earthing point at Tower
-X1
2,5 mm²
to the Main Frame grounding terminal. 1
-WPE10PE20 RD
5m
1x70,00
-K1
-X1 - - - - - 2 3 7 8 + + + + +
/55.3:E
-XP20 6 7 8 PE -XP20 1 2 3 4
E 2,5 mm² E
GNYE 6 7 8 PE 1 2 3 4
-XP21 -XP21
0VDC / 41.0:E
24VDC_1 / 55.0:A
1 On Main Frame
200 / +X0/61.1:E
201 / +X0/61.6:E
202 / +X0/63.1:E
205 / +X0/61.2:E
206 / +X0/61.0:E
207 / +X0/61.5:E
208 / +X0/63.1:E
209 / +X0/61.3:E
24VDC / 41.0:A
50
-PE20
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X0-UC1
Plug
A -XP1 4 5
A
/30.0:E Control Voltage Heater L Control Voltage Heater N
40.9:E / 24VDC + +
24VDC / 50.5:B
-X1 -X1
+X0
2 +X0-WXP1 -XP2
-B6 BK 37G2.5 4 5 Socket at tower
land side right 1 2 PE
21 13
B -B6 B
Limit switch 14
22
Door
2 -WXP2 1 2 GN/YE
-B6 BK/WH
169
-X2 101 102 103 104
-X1
C C
-EA1 BN BK
14 12 44 42
-KA0 -KA0
/41.3:E 11 /41.3:E 41 5
-EA1
Cabinet light BN BK
D D
L
-EB1 3 1
+X0/220.4:D
50W
Heater
BU
A1
-EA1 BU
-KA0 2 4
N
24 V DC A2
E E
40.3:E / 0VDC - -
0VDC / 47.3:E
-X1 -X1
14 11 /41.6:D
12
44 41 /41.7:D
42
Cabinet heater
MACHINE TYPE: SHEET
EH 170U 41
F This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 45
Date
Ed.
25/10/2019
ZAMZUMO © The design and/or constructions
contained therein, may not be copied
CHECKED BY: Service light / heater in X1 cabinet TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
=A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63
CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8
B B
+X100
C 19 20 21 22 23 24 25 26
C
-X3 -X3
-X1 - - - -X1 - - -
D -WHL1-4 BN GN RD OR PK BU YE GY WH TN -WHL5-8 BN GN RD OR PK BU YE GY WH TN D
-WHL1-4 -WHL5-8
BN/N.C GN/L- RD/J1 OR/J1 PK/J2 BU/J2 YE/J3 GY/J3 WH/J4 TN/J4 BN/N.C GN/L- RD/J1 OR/J1 PK/J2 BU/J2 YE/J3 GY/J3 WH/J4 TN/J4
J1:1+ J1:2 pwm J1:3 - J2:1+ J2:2 pwm J2:3 - J3:1+ J3:2 pwm J3:3 - J4:1+ J4:2 pwm J4:3 - J1:1+ J1:2 pwm J1:3 - J2:1+ J2:2 pwm J2:3 - J3:1+ J3:2 pwm J3:3 - J4:1+ J4:2 pwm J4:3 -
E -WHL1-4 J1.1 J1.2 J1.3 J2.1 J2.2 J2.3 J3.1 J3.2 J3.3 J4.1 J4.2 J4.3 -WHL5-8 J1.1 J1.2 J1.3 J2.1 J2.2 J2.3 J3.1 J3.2 J3.3 J4.1 J4.2 J4.3 E
+ PWM - n.c + PWM - n.c + PWM - n.c + PWM - n.c + PWM - n.c + PWM - n.c + PWM - n.c + PWM - n.c
+X0-HL1 +X0-HL2 +X0-HL3 +X0-HL4 +X0-HL5 +X0-HL6 +X0-HL7 +X0-HL8
Green 1 2 3 4 Red 1 2 3 4 White 1 2 3 4 Yellow 1 2 3 4 Green 1 2 3 4 Red 1 2 3 4 White 1 2 3 4 Yellow 1 2 3 4
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A -B1 A
C C
A1 A1 1 1
-K6 -K10 -PG1 -PG2
24 V DC A2 24 V DC A2 2 2
D D
E E
41.4:E / 0VDC - -
0VDC / 50.5:D
-X1 -X1
1 2 /30.5:C 1 2
3 4 /30.5:C 3 4
5 6 /30.5:C 5 6
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
4 4 4 4 4 4 4 4
1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2
-KA1 -KA2 -KA3 -KA4 -KA5 -KA6 -KA7 -KA8
B +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ B
C C
D D
+X0-WXP1 6 7 8 35 20 34
37G2.5
E E
+X0-UC1
Plug
Gravity Point
Locked Unlocked Spreader Landed
-XP1 6
Signal
7
Signal
8
Signal
35 In Centre Sig 20 HIS Signal (option) 34
/30.0:E (Gottwald)
Twin Down
Signal
(Gottwald)
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
4 4 4 4 4 4 4 4
1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2
-KA9 -KA10 -KA11 -KA12 -KA13 -KA14 -KA15 -KA16
B +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ B
230 VAC
49.9:B
41.4:A / 24VDC 24VDC / 54.3:B
C C
D D
47.6:E / 0VDC - -
0VDC / 54.3:D
-X1
+X0-WXP1 36
37G2.5
1 2 /32.3:C 1 2 /31.3:B
3 4 /32.3:C 3 4 /31.3:B
5 6 /32.3:C 5 6 /31.3:B
E E
+X0-UC1
Plug
-XP1 36
/30.0:E
TTDS OK Signal
(option)
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X0-UC1
Plug
A A
-XP1 19 18 13 9 10 12
/30.0:E Telescope Retract Cmd Telescope Expand Cmd Flippers All Up Cmd Green Flippers Down Cmd (2&3) Black Flipper Down Cmd (6) White Flipper Down Cmd (5)
+X0-WXP1 19 18 13 9 10 12
37G2.5
B B
C C
D D
40.4:C / 230 VN 230 VN / 52.0:D
+/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~
-KA17 -KA18 -KA21 -KA22 -KA23 -KA24
1 2 1 2 1 2 1 2 1 2 1 2
4 4 4 4 4 4
CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18
E =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65
E
Input Input Input Input Input Input
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X0-UC1
Plug
A A
-XP1 11 14 15 16 17 21 33
/30.0:E Red Flipper Down Cmd (1&4) Twistlock Lock Cmd Twistlock Unlock Cmd Move Gravity Point To White Cmd Move Gravity Point To Black Cmd Twin Up Cmd (Gottwald) Twin Down Cmd
+X0-WXP1 11 14 15 16 17 21 33
37G2.5
B B
C C
D D
51.8:D / 230 VN
+/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~ +/~ -/~
-KA25 -KA26 -KA27 -KA28 -KA29 -KA30 -KA31 -KA32
1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2
4 4 4 4 4 4 4 4
CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18 CAN node ID18
E =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65 =A1+X1-X18 =A1+X0/65
E
Input Input Input Input Input Input Input Input
-KA25 -KA26 -KA27 -KA28 -KA29 -KA30 -KA31 0-120 V AC Input module
-KA32 Bromma P/N BR78510
Red Flipper Down Twistlock Lock Twistlock Unlock Move Gravity Point Move Gravity Point Twin Up Twin Down
Spare
Cmd (1&4) Cmd Cmd To White Cmd To Black Cmd Cmd (Gottwald) Cmd 0-240 V AC Input module
Bromma P/N BR78511
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X0-UC1
Plug
A -XP1 26 27 28 29 2 37
A
/30.0:E Spare Spare Spare Spare Protective Earth PE Protective Earth PE
B B
+X0-WXP1 26 27 28 29 2 GN/YE
37G2.5
C C
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
50.9:B / 24VDC +
24VDC / 58.0:A
B B
1 2
13
-SW6
Liebherr/ Gottwald 14
C C
-X2 200 201
D D
50.9:D / 0VDC 0VDC / 55.0:E
IO_3 IO_4
-X18 -X18
-KA19 -KA20
Crane Liebherr/ Gottwald Spare
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
40.5:E / 24VDC_1
11
-SS1
Spreader Stop 12
X1 cabinet
-X2 202
B B
-XP26 1
-XP27 1
+X0
-WXP27 1
11
-SS2
Control station
C Spreader stop
12 C
-WXP27 2
-XP27 2
-XP26 2
-X2 203
D D
177 / 58.5:B
-K1 A1
24
Main contactor
E A2 E
54.6:D / 0VDC -
0VDC / +X0/60.1:B
-X1
1 2 /30.1:B
3 4 /30.1:B
5 6 /30.1:B
-K1
8 7 /40.7:E
Main contactor
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X200
A A
24VDC / 57.1:A
13 13 23 13 23 13 23
1 2
-SW1/HL1 -SW2 All flipper -SW3 Twistlock unlock -SW4 G.P to black
Control 14 All flipper down cmd Twistlock lock cmd G.P to white cmd
14 24 14 24 14 24
station on up cmd cmd cmd
B B
-WX200 1 2 3 4 5 6 7 8
+X100
C C
-X2 + -X3 60 61 62 44 45 46 47
-WXP23
/31.3:C 13 14 15 16 17 18 19
D D
-XP23 13 14 15 16 17 18 19
-XP22 13 14 15 16 17 18 19
/31.2:C
E 55 24 33 34 35 36 38 E
IN 00 IN 08 IN 07 IN 05 IN 03 IN 01 IN 15
CAN node ID1 CAN node ID1 CAN node ID1 CAN node ID1 CAN node ID1 CAN node ID1 CAN node ID1
=A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60
Control station All flippers up All flippers down Twistlock lock Twistlock unlock Gravity point to White Gravity Point to Black
On CMD CMD CMD CMD CMD CMD
b 25/3/2019 ZAMZUMO MACHINE TYPE:
EH 170U SHEET
56
F b 19/3/2019 ZAMZUMO This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 57
Date
Ed.
25/10/2019
ZAMZUMO © The design and/or constructions
contained therein, may not be copied
CHECKED BY: Input control station TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X200
Control station turned on
56.9:A / 24VDC
A -B1 A
=A1+X1-B1 =A1+X0/60
X1
13 13 13 13 23 CAN node ID1
-HL1 / SW1
-SB6 -SB7 -SB8 -SW5 Twin down Yellow X2
Black 14 Black 14 Black 14 Twin up cmd Control station turned ON OUT 12
14 24
Telescope Telescope Spare cmd
Retract Expand 06
-WB1 06/WH
B -X2 218 B
-XP20 9
-XP21 9
-WXP21 9
C -WX200 9 10 11 12 13 14 15 C
+X100
-WXP23
D /31.3:C 22 23 24 20 21 D
-XP23 22 23 24 20 21
-XP22 22 23 24 20 21
/31.2:C
E 53 54 52 41 23 E
IN 04 IN 02 IN 06 IN 09 IN 10
CAN node ID1 CAN node ID1 CAN node ID1 CAN node ID1 CAN node ID1
=A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60 =A1+X1-B1 =A1+X0/60
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
54.6:B / 24VDC + +
24VDC / +X0/60.0:B
-X1
32.9:A / 322
32.9:A / 321
32.9:A / 320
55.4:D / 177
BK BK BK 1,5 mm²
B B
200-480V 3~ AC 50/60Hz
L1
1 2
13 L3 L2
C -SB1 C
AUTO RETURN 14 14 12
ON / OFF Relay output
D D
22 39 21
IN 12 IN 13 IN 14
-B5
-SB1
Three phase Spreader stop
Gravity point auto return
monitoring
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X0
62.9:C
+X1-SPR_CAN1 171.5:E 171.4:E
-A9
A CAN to WIFI A
+X1-BTU_CAN2 +X1-BTU_CAN1 Tower
2 3 4 5 1
VBBc GND CAN_H CAN_L SH
-WCAN3 RD WH BK BU SH 2 3 4 5 1
+X1-WA9
1
B B
-X1 + -X1 - -WA9 RD BK WH BU SH
24VDC 24VDC 0VDC 0VDC
+X1/58.9:A 60.3:F +X1/55.9:E 60.5:F
+
24VDC 24VDC 1
60.4:F 65.0:A
-X1 -
0VDC 0VDC
60.6:F 65.0:E
65.2:E 65.2:E
C CAN_H_X17 CAN_L_X17 C
-X1 163 163 164 164 -X1 165 165 166 166
D D
-B1
CAN node ID1 CAN1_H CAN1_L CAN2_H CAN2_L CAN4_H CAN4_L CAN3_H CAN3_L
47 29 46 28 44 26 45 27
X1 cabinet
PLC master
CAN1 nodes at spr. PLC CAN2 DS444 CAN4 BCAN
Download Connector
CAN3 WIFI
CR0032 VBBS VBB15 TEST VBBO VBBR GND GNDA GNDO USB_P USB_N USB_5 V USB_GND
housing
R360/ClassicController/32;BR75331 10 32 50 19 01 20 37 42 30 48 31 49 GND
E E
-WB1 10/WH 32/WH 50/WH 19/WH 01/WH 20/WH 37/WH 42/WH -WX19
M12 A-coded
PLC program loading cable
USB max 5m length
D+ D- USB_5 V USB_GND
+X1/40.6:D / 1B1 -X19 4 2 1 3
+X1/40.6:D / 2B1
+ - -
+X1/40.6:C / 3B1
-X1 + -X1 - PLC program loading cable 2m
24VDC 24VDC -0VDC -0VDC
60.1:B 60.7:B 60.2:B 60.8:C
BR1704495, USB - M12
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
-R2 -R3
120Ω male M12 120Ω male M12
CAN BUS termination CAN BUS termination
A A
SH
SH
CAN node ID2 CAN node ID3
+ VBB c
+ VBB c
2 2 2 2
RD +VBBc RD +VBBc
B B
CAN_GND
CAN_GND
3 3 3 3
Set switch BK CAN_GND Set switch BK CAN_GND
S1 to position 4 S1 to position 4
X2 / 62.1:E X3 / 64.3:E
S2 to position 0 S2 to position 0
4 4
CAN_H
CAN_H
S3 to position 2 4 WH CAN_H S3 to position 3 4 WH CAN_H
5 5
CAN_L
CAN_L
5 BU CAN_L 5 BU CAN_L
XE07 XE03 XE01 XE02 XE04 XE07 XE03 XE01 XE02 XE04
+VBBs module GNDoutput CAN_H CAN_L GNDs modul +VBBs module GNDoutput CAN_H CAN_L GNDs modul
C C
-W2 1 2 -W3 1 2
+X100
-X1 1 2 3
PE busbar
D X100 Cabinet D
-PE1:PE:1
-X2 - -X2 + + + -
-WXP21 1 6 GN/YE 4 2 7
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
63.0:B
X4
A A
2 2 1 1
-WX4 RD BK WH BU SH
B -WX4 2. 3. 4. 5. 1. B
-XB0 X1 2 3 4 5 1 X2 2 3 4 5 1 X4 2 3 4 5 1
Tower + VBB c CAN_GND CAN_H CAN_L SH + VBB c CAN_GND CAN_H CAN_L SH + VBB c CAN_GND CAN_H CAN_L SH
-WXB1 +X1-WCAN1 2 3 4 5 1
2 3 4 5 1
/62.4:C
C C
+VBB c CAN_GND CAN_H CAN_L SH
2 2 1 1
-WXB1 RD BK WH BU SH
60.1:A
+X1-SPR_CAN1
+X100
D D
-X2 + - 5 6 5SH
+VBBc
E E
CAN_GND
CAN_H
61.4:B / X2
CAN_L
SH
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
SH
SH 1 SH SH 1. SH
SH
SH
+ VBB c
CAN IN 2 2. +VBBc
+ VBB c
+ VBB c
2 2 2 2.
VBB +VBBc
Set switch
CAN_GND
3
CAN IN S1 to position 4 Set switch 3. CAN_GND
CAN_GND
CAN_GND
3 3
CAN_GND 3 S2 to position 0 3. CAN_GND S1 to position 4
S3 to position 4 S2 to position 0
4
CAN_L CAN_H
CAN IN S3 to position 8 4. CAN_H
4 4
CAN_L CAN_H
CAN_L CAN_H
CAN_H 4 4. CAN_H
5 5. SH +VBBc CAN_GND CAN_H CAN_L
B CAN_L B
5 5 5 5.
CAN_L CAN_L
2 2 1 1
XE07 XE03 XE01 XE02 XE04
SH + VBB c CAN_GND CAN_H CAN_L -WX10 SH RD BK WH BU
X4 +VBBs module GNDoutput CAN_H CAN_L GNDs modul CAN IN SH 2 3 4 5
62.8:A
-WX8 1 2 3 4 5
-W4 1 2
-WX10 1 2 3 4 5
2 2 1 1 -X10 CAN IN SH 2 3 4 5
-WX8 SH RD BK WH BU Center waterside SH + VBB c CAN_GND CAN_H CAN_L
C CAN node IDA C
+VBBs module
SH +VBBc CAN_GND CAN_H CAN_L XE07
GNDoutput
XE03
CAN_H
XE01
Set switch
CAN_L S1 to position 4
XE02
+X100 S2 to position 0
GNDs modul S3 to position A
-X2 3
XE04
D D
-X2 -
SH + VBB c CAN_GND CAN_H CAN_L
CAN OUT SH 2 3 4 5
-WX5 1. 2. 3. 4. 5.
-WXP21 3 8
2 2 1 1
-WX5 SH RD BK WH BU
E E
SH +VBBc CAN_GND CAN_H CAN_L
+X1-208 +X1-202
+X1/40.8:E +X1/40.4:E
X5
64.0:B
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
-X5 +VBBs module GNDoutput CAN_H CAN_L GNDs modul -X13 +VBBs module GNDoutput CAN_H CAN_L GNDs modul
Center waterside XE07 XE03 XE01 XE02 XE04 TTDS (Option) XE07 XE03 XE01 XE02 XE04
Centre waterside
CAN node ID5
CAN node ID13
-WX13
CAN OUT BR1042993
-WX13 -WX13 CAN IN
SH 1. 1 SH
-WX5 CAN IN SH
SH
SH
SH 1 SH
2
SH
+ VBB c
+ VBB c
2 2. 2 2
RD
+ VBB c
2 2
B +VBBc B
2
CAN_GND
CAN_GND
3 3. 3 3
Set switch BK Set switch
CAN_GND
3
CAN_GND 3 S1 to position 4 S1 to position 4
S2 to position 0 1 S2 to position 0
4 4
CAN_L CAN_H
CAN_L CAN_H
S3 to position 5 4. WH 4 S3 to position D
X5 4
CAN_L CAN_H
63.8:E CAN_H 4
1
5 5. 5 5
BU
5 5
CAN_L
C -WX100 2 3 4 5 1 C
-WX100 RD BK WH BU SH
BR1702911
+X100
D -X2 + - 17 18 7SH D
+VBBc
CAN_GND
CAN_H
E E
61.9:B / X3
CAN_L
SH
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X1
A A
60.8:B / 24VDC +
24VDC / 171.2:A
-X1
-WX17 RD
-W18 RD
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1
SH SH
DIP1 I/O 1-8 DIP2 I/O 9-16 2
DIP1 I/O 1-8 DIP2 I/O 9-16 2
VBB VBB
3 3
ON GND ON GND
4 4
CAN_H CAN_H
1 2 3 4 5 6 7 8 5 1 2 3 4 5 6 7 8 5
CAN_L CAN_L
DIP3 DIP3
C C
-W18
BU
WH
BN
D D
SH
-WX17 BU WH BN SH
24
CAN_H_X17
60.0:C
CAN_L_X17
60.3:C
E E
60.8:C / 0VDC -
0VDC / 171.1:E
-X1
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4 4 4
1 3 1 3 1 3 1 3 1 3 1 3
-WS1-S5
-WS1-S5
-WS2-S6
-WS2-S6
A A A B B B A A A B B B
-WS10
-WS9
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK. BN BU BK BN BU BK
D D
CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2
=A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4 4 4
1 3 1 3 1 3 1 3 1 3 1 3
-WS3-S7
-WS3-S7
-WS4-S8
-WS4-S8
B B B A A A A A A B B B
-WS11
-WS12
BN. BU. BK. BN BU BK BN BU BK BN. BU. BK. BN BU BK BN BU BK
D D
CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3
=A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4 4 4 4 4
1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3
-WS24-S28
-WS24-S28
-WS32-S36
-WS32-S36
-WS27-S31
-WS27-S31
-WS35-S39
-WS35-S39
A A A B B B A A A B B B A A A B B B A A A B B B
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK. BN BU BK BN. BU. BK. BN BU BK BN. BU. BK.
D D
CAN node ID4 CAN node ID4 CAN node ID4 CAN node ID4 CAN node ID4 CAN node ID4 CAN node ID4 CAN node ID4
=A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4 4 4 4 4
1 3 1 3 1 3 1 3 1 3 1 3 1 3 1 3
-WS25-S29
-WS25-S29
-WS33-S37
-WS33-S37
-WS26-S30
-WS26-S30
-WS34-S38
-WS34-S38
A A A B B B A A A B B B A A A B B B A A A B B B
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK. BN BU BK BN. BU. BK. BN BU BK BN. BU. BK.
D D
CAN node ID5 CAN node ID5 CAN node ID5 CAN node ID5 CAN node ID5 CAN node ID5 CAN node ID5 CAN node ID5
=A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64 =A1+X0-X5 =A1+X0/64
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
=A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63 =A1+X0-X4 =A1+X0/63
CAN node ID2 CAN node ID2 CAN node ID3 CAN node ID3 CAN node ID4 CAN node ID4 CAN node ID4 CAN node ID4
B B
-WY15-Y16
-WY25-Y26
-WY27-Y28
-WY7-Y8
C A1 B1 A1 B1 A1 B1 A1 B1 C
-Y7-Y8 -Y15-Y16 -Y25-Y26 -Y27-Y28
A2 B2 A2 B2 A2 B2 A2 B2
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
=A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61 =A1+X0-X2 =A1+X0/61
CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2 CAN node ID2
B B
-WY1-Y2
-WY3-Y4
-WY5-Y6
MSUD1 MSUD2 MSUD1 MSUD2 MSUD1 MSUD2
BK1 BK2 BK3 BK1 BK2 BK3 BK1 BK2 BK3
C A1 B1 A1 B1 A1 B1 C
-Y1-Y2 -Y3-Y4 -Y5-Y6
A2 B2 A2 B2 A2 B2
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
=A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61 =A1+X0-X3 =A1+X0/61
CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3 CAN node ID3
B B
-WY11-Y12
-WY13-Y14
-WY9-Y10 MSUD1 MSUD2 MSUD1 MSUD2 MSUD1 MSUD2
BK1 BK2 BK3 BK1 BK2 BK3 BK1 BK2 BK3
C A1 B1 A1 B1 A1 B1 C
-Y9-Y10 -Y11-Y12 -Y13-Y14
A2 B2 A2 B2 A2 B2
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4
1 3 1 3 1 3 1 3
-WS54-S55
-WS54-S55
-WS52-S53
-WS52-S53
A A A B B B A A A B B B
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK.
D D
XP1 1 3 4 2 XP3 1 3 4 2
L+ L- IN. IN L+ L- IN. IN
CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8
=A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4
1 3 1 3 1 3 1 3
-WS14-S114
-WS14-S114
-WS13-S16
-WS13-S16
A A A B B B A A A B B B
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK.
D D
XP5 1 3 4 2 XP7 1 3 4 2
L+ L- IN. IN L+ L- IN. IN
CAN node ID8 CAN node ID8 CAN node ID8 CAN node ID8
=A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63 =A1+X0-X8 =A1+X0/63
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B B
C C
4 4 4 4
1 3 1 3 1 3 1 3
-WS40-S43
-WS40-S43
-WS41-S42
-WS41-S42
A A A B B B A A A B B B
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK.
D D
XP1 1 3 4 2 XP3 1 3 4 2
L+ L- IN. IN L+ L- IN. IN
CAN node IDA CAN node IDA CAN node IDA CAN node IDA
=A1+X0-X10 =A1+X0/63 =A1+X0-X10 =A1+X0/63 =A1+X0-X10 =A1+X0/63 =A1+X0-X10 =A1+X0/63
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X1
A
MODEM -TF1
Antenna
Top side X1 cabinet A
65.8:A / -24VDC + +
-X1
-XS21 1 2 -TF1
C C
-XS21 24 3 14 4 15 22 33 11 21
-XS21 3RD -XS21 4WH 5BU -XS21 6WH 7BU -XS21 8WH 10WH 9BU 11BU
D D
-WT1
Chassi mounted M12
CAN_H CAN_L CAN_H CAN_L 0.5m WH/OG WH/GN OG GN
65.8:E / -0VDC -
-X1
BTU_CAN1 BTU_CAN2
60.7:A 60.3:A -WT1 1 2 3 4
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
TTDS -S95
NC
-S93 -S91
NO NO
-S96
NC
A
B B
C C
4 4 4 4 4 4 4
1 3 1 3 1 3 1 3 1 3 1 3 1 3
-WS93-S91
-WS93-S91
-WS92-S90
-WS92-S90
-WS95-S96
-WS95-S96
A A A B B B A A A B B B A A A B B B
-WS94
BN BU BK BN. BU. BK. BN BU BK BN. BU. BK. BN BU BK BN BU BK BN. BU. BK.
D D
CAN node ID13 CAN node ID13 CAN node ID13 CAN node ID13 CAN node ID13 CAN node ID13 CAN node ID13 CAN node ID13
=A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64 =A1+X0-X13 =A1+X0/64
E E
-S93 TTDS sensor -S91 TTDS sensor -S92 TTDS sensor -S90 TTDS sensor -S94 TTDS sensor Spare -S95 TTDS sensor -S96 TTDS sensor
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
-HL9 -HL10
A Twin legs Twin legs A
down landside down waterside
-X10 -X10
OUT. L+ L- OUT
XP2 4 1 XP2 3 2
B B
-W54 BK BN BU WH
C C
+X100
-X2 27 - 28
D D
-WHL9 BN WH BK BU -WHL10 BU BN WH BK
-WHL9 1 2 4 3 -WHL10 3 1 2 4
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X1
160 mm
C C
275 mm
BROMMA CONQUIP
Box 1133
SE-164 22 KISTA
SWEDEN
Control Cabinet
Circuit
diagram no. BR1707652
Rated voltage A Hz IP
400 V 3~/PE AC 30 50 66
16
Spreader No. SN 30874
Year of manufacturing
2014/30/EU 20XX
2014/35/EU
Art. No. 1002455
150 mm
SB1
AUTO RETURN
SW6
Liebherr/ Gottwald
QA1
ON / OFF
12 14 11
D SS1
Spreader Stop
18
E E
115 mm
10
130 mm
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
115 mm
no 1.
130 mm
no Diamater Function
1 Ø 19 mm -TF1 Antenna
2 - -
B 3 - - B
Pin 1 4 - -
5 - -
6 - -
Pin 1
13
1
1
C C
14
2
2
15
3
3
16
4
17
5
18
6
13
1
14
2
15
3
19
16
4
7
17
5
XP22/23
18
6
XP26/27
19
7
20
1
20
8
8
21
2
9
10
22
3
24pol Female
11
23
21
12
24
6pol Female
9
10
22
11
23
D D
12
24
1
6
Pin 1
2
7
XP20/21
3
8
4
9
10
5
10pol Female
1
6
2
7
3
8
4
9
E E
10
5
MACHINE TYPE: SHEET
EH 170U 212
F This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 214
Date
Ed.
25/10/2019
ZAMZUMO © The design and/or constructions
contained therein, may not be copied
CHECKED BY: Cabinet enclosure back view MHC TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
External cable connection between X1, X100 cabinet and X200 A
B B
XP27
WXP27
XP23
XP26
XP22
24pol Female
C
6pol Female
P/N BR76291 C
XP21
XP20
10pol Female
D WX200 D
P/N BR76945
X100
WXP21
P/N BR701118
E E
WXP23
P/N BR78703
MACHINE TYPE: SHEET
EH 170U 214
F This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 216
Date
Ed.
25/10/2019
ZAMZUMO © The design and/or constructions
contained therein, may not be copied
CHECKED BY: Spreader layout plug cable TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
ENGRAVING SIGN PLATE SPREADER A
B B
Year of manufacturing
2014/30/EU 20XX
2014/35/EU
Art. No. 1002455
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
BRAKE AND CURRENT RELAY FOR EH170U TOWER & TELE DRIVE A
SR
B
ws rt B
ws bl
C BGE C
ws
1
W2 U2 V2 rt
2
BS
3
TS
4
D D
U1 V1 W1 bl
5
Wire colours
ws = white
rt= red
bl = blue
Brake
E E
L1 L2 L3 BS = Accelerator coil
TS = Fractional coil
Accelerator coil winding resistance = ¼ of winding resistance
Fractional coil winding resistance = ¾ of winding resistance
Total coil winding resistance = sum of accelerator and holding coil resistance
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X1
A A
Mounting plate electrical cabinet X1
-BP1
Mounting plate
-X17 -X18
X1 cabinet 118 119
37.5x75x160 mm
DIP1 DIP2 DIP3 DIP1 DIP2 DIP3
ON ON
740x733 mm X1 cabinet
OFF OFF
B B
37.5x75x662 mm
-K2 -K8 -QM1 -QM8 -K1
K6
333 334 K10
335
336 337 339 340
-P2 1/ L1 3/ L2 5/ L3
1/ L1 3/ L2 5/ L3
255
SIEMENS
21NC
13NO A1+
21NC
13NO A1+
SIEMENS
5SY6102-7
-B5
C -FC1
120 253 C
A2-
A2-
3RV2 3. 4. 5. 6.
3. 4. 5. 6.
22NC
22NC 14NO
14NO
3RT20
3RT20
37.5x75x675 mm
2/ T1 4/ T2 6/ T3
2/ T1 4/ T2 6/ T3
37.5x75x614 mm
-PG1 -PG2 -FC2
30A
342 343 346
-KA0
5A
341
37.5x75x475 mm
X1
163
163
164
164
165
165
166
166
169
SIEMENS
5SY62
-EB1
179
D D
37.5x75x170 mm
-TA1
91
37.5x75x460 mm
X1 X1 X2
L1
L1
L2
L2
L3
L3
B1+
B1+
106
105
108
300
301
302
303
+
+
+
+
+
+
+
+
+
N
N
N
N
N
N
N
N
N
1
2
3
L
L
L
L
L
L
L
2
3
-
-
-
-
-
-
-
-
-
E E
50x75x732 mm
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
+X1
A A
B B
C C
-BP2
Right door
D D
-T1
2
-B1
1
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
Terminal strip A
30A
5A
X1 X1
X1
B1+
B1+
300
301
302
303
163
163
164
164
165
165
166
166
169
+
+
+
+
+
+
+
+
+
2
3
-
-
-
-
-
-
-
-
-
B B
C C
X2
L1
L1
L2
L2
L3
L3
106
105
108
N
N
N
N
N
N
N
N
N
1
2
3
L
L
L
L
L
L
L
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
X100 ELECTRICAL CABINET MHC EH170U A
17
15
1 2 3 4 5 6 7
B B
8 9 10 11 12 13 14
19 18 16
464 mm
C C
Bottom view Left / Right side
252 mm
1 M16 W2 15 M32 WXP23
50 mm
3 M16 WXB1 17 M32 WXP21
7 M16 WMA3
9 M16 W3
10 M16 W62
E E
11 M16 W63
12 M16 WHL5-8
13 M16 WMA4
14 M16 WMA5
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
Cabinet X100 mounting plate A
B B
D D
SHIELD 1-7 PE
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
B SW2 SW1/HL1 B
C SW5 SB6 C
D
SW3 SB7 D
SW4 SB8
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Wire no.
Wire no.
Wire no.
A A
Pin no.
Pin no.
Pin no.
Function text Page / column Function text Page / column Function text Page / column
9 9 Green Flippers Down Cmd (2&3) +X1/51.4:A 33 33 Twin Down Cmd +X1/52.7:A
C C
10 10 Black Flipper Down Cmd (6) +X1/51.5:A 34 34 HIS Signal (option) +X1/49.8:E
11 11 Red Flipper Down Cmd (1&4) +X1/52.1:A 35 35 Spreader Landed Signal +X1/49.4:E
12 12 White Flipper Down Cmd (5) +X1/51.6:A 36 36 TTDS OK Signal (option) +X1/50.1:E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
B B
4 3 2 1
9 8 7 6 5
C C
15 14 13 12 11 10
22 21 20 19 18 17 16
28 27 26 25 24 23
33 32 31 30 29
37 36 35 34
D D
Male Insert
Socket ODU309 View From Soldering Side
Bromma P/N: BR73523 Bromma P/N: BR74410
ODU P/N: 309 020 000 554 000 Male Insert: ODU P/N: 309 803 150 037 151
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
X1 CABINET
B B
WATERSIDE
CONTROL STATION
E E
LANDSIDE
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A A
LANDSIDE
B WATERSIDE B
C C
MA1
D D
LEFT RIGHT
S24 UNLOCK S27 UNLOCK S26 UNLOCK S25 UNLOCK
S28 LOCK S31 LOCK S30 LOCK S29 LOCK
S32 LANDED S35 LANDED S34 LANDED S33 LANDED
S36 TWIN UP S39 TWIN UP S38 TWIN UP S37 TWIN UP
S40 TWIN DOWN S43 TWIN DOWN S42 TWIN DOWN S41 TWIN DOWN
E E
Scale 1:38
MACHINE TYPE: SHEET
EH 170U 256
F This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 +SPS/270
Date
Ed.
25/10/2019
ZAMZUMO © The design and/or constructions
contained therein, may not be copied
CHECKED BY: Spreader layout TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F20_001_CR0020
PLC card overview
+X1-B1
A A
X1 cabinet
BR1029845
Inputs PLC master Outputs
I/O in I/O out
Function text Page Connection from PLC connection point PLC connection point Function text Page Connection from
55 18
Control station On +X1/56.2:E =A1+X1-XP22:13 IN 00 OUT 00 Spare
B B
=A1+X1-XP22:18 36 17
Gravity point to White CMD +X1/56.7:E IN 01 OUT 01 Spare
54 16
30Ft Cmd +X1/57.2:E =A1+X1-XP22:23 IN 02 OUT 02 -K6 Hydraulic pump Left & right end bea +X1/47.3:B =A1+X1-K6:A1
35 15
Twistlock unlock CMD +X1/56.6:E =A1+X1-XP22:17 IN 03 OUT 03 Spare
53 14
20Ft Cmd +X1/57.1:E =A1+X1-XP22:22 IN 04 OUT 04 Spare
34 13
C Twistlock lock CMD +X1/56.5:E =A1+X1-XP22:16 IN 05 OUT 05 -K10 Hydraulic pump twin +X1/47.4:B =A1+X1-K10:A1 C
52
IN 06 12
40Ft Cmd +X1/57.3:E =A1+X1-XP22:24 OUT 06 Spare
33 11
All flippers down CMD +X1/56.4:E =A1+X1-XP22:15 IN 07 OUT 07 Spare
24 02
All flippers up CMD +X1/56.3:E =A1+X1-XP22:14 IN 08 OUT 08 Spare
41 03
Twin Up CMD +X1/57.4:E =A1+X1-XP22:20 IN 09 OUT 09 Spare
23 04
D Twin Down CMD +X1/57.5:E =A1+X1-XP22:21 IN 10 OUT 10 Spare D
40 05
Spare IN 11 OUT 11 Spare
22 06
-SB1 Gravity point auto return +X1/58.2:E =A1+X1-SB1:14 IN 12 OUT 12 Control station turned on +X1/57.9:B =A1+X1-XP20:9
39 07
-B5 Three phase monitoring +X1/58.4:E =A1+X1-B5:14 IN 13 OUT 13 -PG1 Container counter Single Container +X1/47.5:B =A1+X1-PG1:1
21 08
Spreader stop +X1/58.6:E =A1+X1-K1:A1 IN 14 OUT 14 -PG2 Container counter Twin Container +X1/47.6:B =A1+X1-PG2:1
38 09
Gravity Point to Black CMD +X1/56.8:E =A1+X1-XP22:19 IN 15 OUT 15 Spare
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
+X0-X2 +X0-X3 A
Pin
Pin
Pin
Inputs Outputs Inputs Outputs
XP7 XP8 XP7 XP8
Connection XP7 Connection XP8 Connection XP7 Connection XP8
2 Spare 4 -Y5 Flipper 5 blue up 2 Spare 4 -Y13 Flipper 6 yellow up
B B
4 -S10 Landed left waterside 2 -Y6 Flipper 5 blue down 4 -S12 Landed right landside 2 -Y14 Flipper 6 yellow down
4 -S9 Landed left landside 2 -Y4 Flipper 2 green down 4 -S11 Landed right waterside 2 -Y12 Flipper 4 red down
XP3 XP4 XP3 XP4
Connection XP3 Connection XP4 Connection XP3 Connection XP4
2 -S6 Locked left waterside 4 -Y1 Flipper 1 red up 2 -S8 Locked right landside 4 -Y9 Flipper 3 green up
C 4 -S2 Unlocked left waterside 2 -Y2 Flipper 1 red down 4 -S4 Unlocked right landside 2 -Y10 Flipper 3 green down C
XP1 XP2 XP1 XP2
Connection XP1 Connection XP2 Connection XP1 Connection XP2
2 -S5 Locked left landside 4 -Y7 Twistlock unlock left end beam 2 -S7 Locked right waterside 4 -Y15 Twistlock unlock right end beam
4 -S1 Unlocked left landside 2 -Y8 Twistlock lock left end beam 4 -S3 Unlocked right waterside 2 -Y16 Twistlock lock right end beam
CAN IN CAN OUT CAN IN CAN OUT
D D
XE01 XE02 XE03 XE04 XE05 XE06 XE07 XE01 XE02 XE03 XE04 XE05 XE06 XE07
CAN_H
CAN_L
GNDoutput
GNDs modul
CAN_H
CAN_L
GNDoutput
GNDs modul
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
+X0-X4 +X0-X5 A
Pin
Pin
Pin
Inputs Outputs Inputs Outputs
XP7 XP8 XP7 XP8
Connection XP7 Connection XP8 Connection XP7 Connection XP8
2 -S39 Twin (8) up right landside 4 Spare 2 -S38 Twin (7) up right waterside 4 Spare
B B
4 -S35 Twin (8) landed right landside 2 Spare 4 -S34 Twin (7) landed right waterside 2 Spare
4 -S27 Twin (8) unlocked right landside 2 Spare 4 -S26 Twin (7) unlocked right waterside 2 Spare
XP3 XP4 XP3 XP4
Connection XP3 Connection XP4 Connection XP3 Connection XP4
2 -S36 Twin (5) up left landside 4 -Y27 Twin twistlock unlock 2 -S37 Twin (6) up left waterside 4 Spare
C 4 -S32 Twin (5) landed left landside 2 -Y28 Twin twistlock lock 4 -S33 Twin (6) landed left waterside 2 Spare C
XP1 XP2 XP1 XP2
Connection XP1 Connection XP2 Connection XP1 Connection XP2
2 -S28 Twin (5) locked left landside 4 -Y25 Twin legs up 2 -S29 Twin (6) locked left waterside 4 Spare
4 -S24 Twin (5) unlocked left landside 2 -Y26 Twin legs down 4 -S25 Twin (6) unlocked left waterside 2 Spare
CAN IN CAN OUT CAN IN CAN OUT
D D
XE01 XE02 XE03 XE04 XE05 XE06 XE07 XE01 XE02 XE03 XE04 XE05 XE06 XE07
CAN_H
CAN_L
GNDoutput
GNDs modul
CAN_H
CAN_L
GNDoutput
GNDs modul
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
+X0-X8 +X0-X10 A
Pin
Pin
Pin
Inputs Outputs Inputs Outputs
XP7 XP8 XP7 XP8
Connection XP7 Connection XP8 Connection XP7 Connection XP8
2 -S114 30 ft telescope position 4 -HL7 Spreader landed right 2 Spare 4 Spare
B B
4 -S14 30 ft telescope position 2 -HL8 Tower in centre right 4 Spare 2 Spare
C 4 -S52 Gravity point tower left centre 2 -HL4 Tower in centre left 4 -S41 Twin corner (6) down left waterside 2 Spare C
XP1 XP2 XP1 XP2
Connection XP1 Connection XP2 Connection XP1 Connection XP2
2 -S55 Gravity point tower right stop 4 -HL1 Twistlock unlocked left 2 -S43 Twin corner (8) down right landside 4 -HL9 Twin legs down landside
4 -S54 Gravity point tower left stop 2 -HL2 Twistlock locked left 4 -S40 Twin corner (5) down left landside 2 -HL10 Twin legs down waterside
CAN IN CAN OUT CAN IN CAN OUT
D D
XE01 XE02 XE03 XE04 XE05 XE06 XE07 XE01 XE02 XE03 XE04 XE05 XE06 XE07
CAN_H
CAN_L
GNDoutput
GNDs modul
CAN_H
CAN_L
GNDoutput
GNDs modul
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
A
+X0-X13 A
Centre waterside
CAN node ID13
Pin
Pin
Pin
Pin
Inputs Outputs Inputs Outputs
XP7 XP8
Connection XP7 Connection XP8 Connection Connection
2 -S96 TTDS sensor 4 Spare
B B
4 -S95 TTDS sensor 2 Spare
XP5 XP6
Connection XP5 Connection XP6 Connection Connection
2 Spare 4 Spare
D D
XE01 XE02 XE03 XE04 XE05 XE06 XE07
CAN_H
CAN_L
GNDoutput
GNDs modul
E E
0 1 2 3 4 5 6 7 8 9
D
A
C
B
F
291
+PART/300
108
d
REV.
F20_001 BR1703273_V1.01
TOTAL SH.
BR1707652
SHEET
CONT.
9
9
IO_15 IO_16
BR78511
Distributed I/O overview
IO_14
DIP1 DIP2 DIP3
BR78511
IO_10
BR78511
+X1-X18
BR1703273
IO_9
230 V AC input orange +X1/52.1:E -KA25 Red Flipper Down Cmd (1&4)
BR78511
7
7
IO_8
120 V AC input orange +X1/51.6:E -KA24 White Flipper Down Cmd (5)
SPS
BR78510
A1
PLANT (=)
UNIT (+)
6
VBB.
24 V DC input white
IO_4
CAN_L.
CAN_H.
BR78509 +X1/54.5:E -KA20 Spare
DRAWING DATE:
MACHINE TYPE:
CHECKED BY:
DRAWN BY:
SH.
SERIAL NO.
24 V DC input white
IO_3
BR78511
5
5
Page Function text
4
4
IO_15 IO_16
IO_14
24 V DC output red
+X1/50.6:B -KA14 Gravity Point To Black
24 V DC output red
BR78513 +X1/50.5:B -KA13 Gravity Point To White
3
3
consent of the owner.
0-240 V AC output black
IO_11 IO_12
BR78514
+X1-X17
=A1+X0/65
X1 cabinet
BR1703273
©
IO_9
0-240 V AC output black +X1/50.1:B -KA9 TTDS ok signal (option)
BR78514
2
2
V:\P8\Projects\MHC\EH170U\BR1707652_MHC_EH170U_Sociedad Portu
IO_8
0-240 V AC output black +X1/49.8:B -KA8 HIS Signal (option)
ZAMZUMO
20/9/2019
BR78514
0-240 V AC output black
IO_7
BR78514 +X1/49.7:B -KA7 Gravity Point At Black Signal
Appr
Date
aria S.A._SN30874\BR1707652_d.ell
Ed.
0-240 V AC output black
IO_6
BR78514 +X1/49.6:B -KA6 Gravity Point At White Signal
0-240 V AC output black
IO_5
+X1/49.5:B -KA5 Gravity Point In Centre Signal (Gottwald)
Original
GND. BR78514
VBB.
0-240 V AC output black
1
1
IO_4
CAN_L.
CAN_H.
BR78514 +X1/49.4:B -KA4 Spreader Landed Signal
SH.
PLC card overview
IO_3
BR78514 +X1/49.3:B -KA3 Unlocked Signal
Description
0-240 V AC output black
IO_2
BR78514 +X1/49.2:B -KA2 Locked Signal
0-240 V AC output black +X1/49.1:B -KA1 Twin legs down signal
IO_1
Name
BR78514
0
0
Page Function text
Date
Mod.
D
A
C
B
F
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
1 9 +X0/220.6:D BR1028250 TERMINAL 2,5mm² Phoenix Contact 3031720 3-CONDUCTOR GRAY
2 X1 B1 1 +X0/60.0:D BR1029845 Programmable mobile controller type R 360 IFM CR0032 16 inputs / 16 outputs
3 X1 B1 4 +X0/60.0:D BR75331 SCREW M6S 5x12 Bromma BR75331 FZB, CLASS 8.8, ISO 4014
4 X1 B1 4 +X0/60.0:D BR77889 NUT LOC-KING M5 BROMMA BR77889 DIN 985, A4, KLASS 70
5 X1 B5 1 +X1/58.3:B BR1705892 Monitoring relay Omron K8DT-PH1CN 3 phase, phase sequence & phase loss 200-480 VAC
8 X1 B6 2 +X1/41.1:B BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
B B
9 X1 B6 2 +X1/41.1:B BR75329 WASHER BRB 4,3x9x0,8 Bromma BR75329 FZB
10 X1 BP1 1 +X0/220.2:B BR1245221 Cabinet EH5U/EH170U SCS4/MidR Bromma BR1245221 T=2, Material SS 1.4404, IP 66
11 X1 BP1 10 +X0/220.2:B BR75381 Single Strand Cable Helukabel 29133 Red 1,5mm²
12 X1 BP1 10 +X0/220.2:B BR76155 Single Strand Cable Helukabel 29147 Blue 2,5mm²
13 X1 BP1 20 +X0/220.2:B BR70595 Single Strand Cable Helukabel 29145 Black 2,5mm²
14 X1 BP1 100 +X0/220.2:B BR76577 Single Strand Cable Helukabel 29131 Blue 1,5mm²
16 X1 BP1 4 +X0/220.2:B BR70414 Single Strand Cable Helukabel 29149 Red 2,5mm²
C C
17 X1 BP1 3 +X0/220.2:B BR76131 Single Strand Cable Helukabel 29146 Yellow/Green 2,5mm²
24 X1 BP1 6 +X0/220.2:B BR77896 WASHER BRB 5,3x10x1 Bromma BR77896 A4, ISO 7089
28 X1 BP1 1 +X0/220.2:B BR1018173 CABLE CLIPS AQ MEKATRONIK AQM6001-1 CABEL DIM. 6mm
29 X1 BP1 50 +X0/220.2:B BR1703074 FERRULE 2.5 Altech 3200205 12mm Stripping length
30 X1 BP1 6 +X0/220.2:B BR1703554 End cap PXC 1206573 TS 35 / DIN rail protection cap
31 X1 BP1 1 +X0/220.2:B BR78314 Single Strand Cable Helukabel 29162 Yellow/Green 4,0mm²
37 X1 BP1 1 +X0/220.2:B BR1000731 GLAND NUT LAPPKABEL 52103060 FOR GLAND M50
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
40 X1 BP1 1 +X0/220.2:B BR701018 GLAND MS-M25 9-17mm Skintop 12 58 13 M25x1.5
41 X1 BP1 6 +X0/220.2:B BR1001911 GLAND NUT LAPPKABEL 52103030 FOR GLAND M25
43 X1 BP1 2 +X0/220.2:B BR1188037 Blanking plate with rubber gasket Bromma BR1188037 Assy
44 X1 BP2 2 +X0/221.5:D BR1703554 End cap PXC 1206573 TS 35 / DIN rail protection cap
45 X1 BP2 2 +X0/221.5:D BR1018173 CABLE CLIPS AQ MEKATRONIK AQM6001-1 CABEL DIM. 6mm
47 X1 EA1 4 +X1/41.0:D BR75606 SCREW MC6S M4x16 BROMMA BR75606 FZB 8.8
B B
48 X1 EA1 4 +X1/41.0:D BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
50 X1 FC1 1 +X1/32.9:C BR1001828 CIRCUIT BREAKER 230/400V 6KA, 1-POLE, C, 2A, D=70MM SIE 5SY6102-7
51 X1 FC2 1 +X1/40.2:B BR1001829 MAIN CIRCUIT BREAKER SIEMENS 5SY6 210-7 C-CHARACTER
53 X1 Gland_X1 1 +X0/171.8:B BR1001911 GLAND NUT LAPPKABEL 52103030 FOR GLAND M25
59 X1 K10 1 +X1/47.4:D BR1000763 CONTACTOR Siemens 3RT2025-1BB40 24VDC 7.5KW 17A SIZE 0
60 X1 KA0 1 +X1/41.3:E BR1703194 Relay socket PXC 2833563 For 2 & 4 switching relay
61 X1 KA0 1 +X1/41.3:E BR1703188 Single relay PXC 2903660 Single relay 2-pole
62 X1 KA0 1 +X1/41.3:E BR1703557 Relay retaining bracket PXC 2905984 For 2 & 4 Switching
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
79 X1 P2 1 +X1/32.9:C BR70873 COUNTERS BAUSER 632A.2
84 X1 PE60 1 +X0/60.2:B BR76131 Single Strand Cable Helukabel 29146 Yellow/Green 2,5mm²
93 X1 QA1 1 +X1/30.1:C BR700871 AUXILIARY BLOCK Baco 172179 NO+NC 400V 10A SIGNALCONTACT
94 X1 QM1 1 +X1/32.3:A BR78993 THERMAL-MAGNETIC CIRCUIT BREAKER SIEMENS 3RV2021-4BA10 7.5KW 14-20A
C C
95 X1 QM6 1 +X1/30.5:B BR1021186 THERMAL SIEMENS 3RV1121-1JA10 4KW 7-10A
96 X1 QM8 1 +X1/31.3:A BR79043 THERMAL-MAGNETIC CIRCUIT BREAK Siemens 3RV2011-1HA10 3,0kW 5,5-8A
97 X1 SB1 1 +X1/58.2:C BR1019832 SWITCH HEAD BACO L21KA03 Only operating head 2 pos, 45º, Ø22,5 mm
98 X1 SB1 1 +X1/58.2:C BR1019811 AUXILIARY BLOCK BACO 331E10 switch body with 1NO block
99 X1 SB1 1 +X1/58.2:C BR1704671 Legend holder Schneider Electric ZBZ34 For harmony series XB5,
101 X1 SS1 1 +X1/55.3:B BR1010842 TRIGGER ACTION BUTTON BLACK TELEMEC ZB5-AS52 BLACK Ø40 TURN RELEASE
102 X1 SS1 1 +X1/55.3:B BR1000712 AUXILIARY BLOCK TELEMEC ZB5-AZ105 switch body with 1 NC and 1NO block
D 103 X1 SS1 1 +X1/55.3:B BR700131 Auxiliary block Schneider Electric ZBE102 Single contact block for head Ø22 1NC D
104 X1 SS1 1 +X1/55.3:B BR1704671 Legend holder Schneider Electric ZBZ34 For harmony series XB5,
106 X1 SW6 1 +X1/54.4:B BR1019832 SWITCH HEAD BACO L21KA03 Only operating head 2 pos, 45º, Ø22,5 mm
107 X1 SW6 1 +X1/54.4:B BR1019811 AUXILIARY BLOCK BACO 331E10 switch body with 1NO block
108 X1 SW6 1 +X1/54.4:B BR1704671 Legend holder Schneider Electric ZBZ34 For harmony series XB5,
110 X1 T1 1 +X0/171.2:B BR1707005 Modem Datarespons 801622 2xCAN selecttable 120Ohm, Ethernet 10/100 Mbit, WIFI, GPS,2xGSM
111 X1 TA1 1 +X1/40.2:C BR1705369 1 Phase Switched-mode power supply 24 V DC IFM ZB0807 Output current 20 A, regulated
E E
112 X1 TF1 1 +X0/171.6:A BR1706993 Antenna for modem Smarteq 710363
114 X1 W60 1 +X1/45.1:B BR1031355 CABLE CONNECTOR IFM EVC080 5m, M12 4P, Angle Male/Open End
115 X1 W61 1 +X1/45.3:B BR1031355 CABLE CONNECTOR IFM EVC080 5m, M12 4P, Angle Male/Open End
116 X1 W62 1 +X1/45.5:B BR1031355 CABLE CONNECTOR IFM EVC080 5m, M12 4P, Angle Male/Open End
117 X1 W63 1 +X1/45.7:B BR1031355 CABLE CONNECTOR IFM EVC080 5m, M12 4P, Angle Male/Open End
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
118 X1 WB1 1 +X0/60.1:E BR1704390 Harness for CR0032 Connector AMP 55-pole Boomerang Cable OU
119 X1 WCAN3 1 +X0/60.0:B BR1702908 CABLE CONNECTOR TURCK WKC5701-5M 5m, M12 5P, Angle Female/Open End
120 X1 WHL1-4 1 +X1/45.0:D BR1701780 Split cable TURCK V9-7/4WK 4.4T-0,3/0,3/0,3/0,3/S90/CS14252 1x7m open end / 4x0,3m M12 female
121 X1 WHL5-8 1 +X1/45.5:D BR1701780 Split cable TURCK V9-7/4WK 4.4T-0,3/0,3/0,3/0,3/S90/CS14252 1x7m open end / 4x0,3m M12 female
122 X1 WMA4 1 +X1/31.3:D BR78173 PUR Control Cable PURö-JZ 4G1,5 mm² GY HELU 22150 4G 1,5mm²
124 X1 WT1 1 +X0/171.7:E BR79282 GLAND PLUG MURR Elektronik 40 57 05 ASB BOX PLUGS M12
127 X1 WXP23 1 +X1/31.3:C BR78703 Multi Core Cable Helukabel 22542 25G 1,5mm²
136 X1 X1 1 +X1/40.5:D BR1040676 Plug-in bridge PXC 3030284 TERMINAL JUMPER FOR TERMINAL FUSE
137 X1 X1 5 +X0/60.9:C BR1028254 End cover PXC 3031762 Separator plate for STS 2,5-TWIN
145 X1 X2 23 +X0/220.5:E BR1028250 TERMINAL 2,5mm² Phoenix Contact 3031720 3-CONDUCTOR GRAY
149 X1 X2 3 +X1/40.2:C BR1028254 End cover PXC 3031762 Separator plate for STS 2,5-TWIN
150 X1 X17 1 +X0/65.0:B BR1703273 Plank Type III IFM ZZ7059 16 independent Delcon I/O
E E
151 X1 X17 4 +X0/65.0:B BR1029642 SCREW MC6S M4x12 BROMMA BR1029642 FZB 8.8
152 X1 X17 8 +X0/65.0:B BR75329 WASHER BRB 4,3x9x0,8 Bromma BR75329 FZB
153 X1 X17 4 +X0/65.0:B BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
154 X1 X18 1 +X0/65.3:B BR1703273 Plank Type III IFM ZZ7059 16 independent Delcon I/O
155 X1 X18 4 +X0/65.3:B BR1029642 SCREW MC6S M4x12 BROMMA BR1029642 FZB 8.8
156 X1 X18 8 +X0/65.3:B BR75329 WASHER BRB 4,3x9x0,8 Bromma BR75329 FZB
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
157 X1 X18 4 +X0/65.3:B BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
158 X1 XP20 1 +X1/40.3:E BR70849 Insert HAR 09330102701 1-10P+PE Screw terminals
159 X1 XP20 1 +X1/40.3:E BR1013547 Housing HAR 09300100303 HARTING 10P COVER 1xLever
160 X1 XP20 4 +X1/40.3:E BR79928 SCREW MC6S 4x16 Bromma A4, CLASS 70, ISO 4762
161 X1 XP20 8 +X1/40.3:E BR701380 WASHER BRB 4,3x9x0,8 Bromma BR701380 A4, ISO 7089
162 X1 XP20 4 +X1/40.3:E BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
163 X1 XP21 1 +X1/40.3:E BR70848 Insert HAR 09330102601 Harting 1-10P+PE Screw terminals
164 X1 XP21 1 +X1/40.3:E BR1031466 Housing HAR 19300101541 Side entry M25x1 2xhook
B B
165 X1 XP21 1 +X1/40.3:E BR701018 GLAND MS-M25 9-17mm Skintop 12 58 13 M25x1.5
166 X1 XP22 1 +X1/31.2:C BR71949 INSERT HARTING 9330242701 HARTING 1-24P SCREW TERMINAL
167 X1 XP22 1 +X1/31.2:C BR77856 Housing HAR 09300240304 Harting 24P COVER 1xLEVER
168 X1 XP22 4 +X1/31.2:C BR79928 SCREW MC6S 4x16 Bromma A4, CLASS 70, ISO 4762
169 X1 XP22 8 +X1/31.2:C BR701380 WASHER BRB 4,3x9x0,8 Bromma BR701380 A4, ISO 7089
170 X1 XP22 4 +X1/31.2:C BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
171 X1 XP23 1 +X1/31.2:C BR71946 INSERT HARTING 9330242601 HARTING 1-24P SCREW TERMINAL
174 X1 XP26 1 +X1/55.2:B BR79696 HARTING HARTING 9300060302 HARTING 6P COVER 1xLEVER
175 X1 XP26 1 +X1/55.2:B BR79334 INSERT HARTING 9330062701 HARTING 6P SCREW TERMINAL
176 X1 XP26 4 +X1/55.2:B BR79928 SCREW MC6S 4x16 Bromma A4, CLASS 70, ISO 4762
177 X1 XP26 8 +X1/55.2:B BR701380 WASHER BRB 4,3x9x0,8 Bromma BR701380 A4, ISO 7089
178 X1 XP26 4 +X1/55.2:B BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
179 X1 XP27 1 +X1/55.2:B BR700211 HARTING HARTING 9300060543 HARTING 6P PG29 1-LEVERS HIGH
184 X1 XP27 1 +X1/55.2:B BR79115 INSERT HARTING 9330062601 HARTING 6P SCREW TERMINAL
186 X1 XS21 1 +X0/171.1:B BR1707013 Modem Power & Data Connector Boomerang Cable OU BR1707013 2,5m female type AMP 35pin for power/2xCAN/Ethernet
187 X1 30_1 1 +X1/30.6:C BR70972 WIRE RING Nelco 2538.0 1,5-2,5 mm²
189 X0 HL1 1 +X1/45.0:E BR1701085 LED'S & LAMPS WITH COLOR CODES TURCK 3026639 GREEN Color PWM
E E
190 X0 HL2 1 +X1/45.1:E BR1701086 LED'S & LAMPS WITH COLOR CODES TURCK 3026666 RED Color PWM
191 X0 HL3 1 +X1/45.2:E BR1701089 LED'S & LAMPS WITH COLOR CODES TURCK 3026716 WHITE Color PWM
192 X0 HL4 1 +X1/45.3:E BR1701088 LED'S & LAMPS WITH COLOR CODES TURCK 3026667 YELLOW Color PWM
193 X0 HL5 1 +X1/45.5:E BR1701085 LED'S & LAMPS WITH COLOR CODES TURCK 3026639 GREEN Color PWM
194 X0 HL6 1 +X1/45.6:E BR1701086 LED'S & LAMPS WITH COLOR CODES TURCK 3026666 RED Color PWM
195 X0 HL7 1 +X1/45.7:E BR1701089 LED'S & LAMPS WITH COLOR CODES TURCK 3026716 WHITE Color PWM
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
196 X0 HL8 1 +X1/45.8:E BR1701088 LED'S & LAMPS WITH COLOR CODES TURCK 3026667 YELLOW Color PWM
197 X0 HL9 1 +X0/200.3:E BR1701087 LED'S & LAMPS WITH COLOR CODES TURCK 3026668 BLUE Color PWM
198 X0 HL10 1 +X0/200.5:E BR1701087 LED'S & LAMPS WITH COLOR CODES TURCK 3026668 BLUE Color PWM
201 X0 R2 1 +X0/61.0:A BR1019449 CAN Termination IFM E11590 M12 connector 120ohm 0,25W
202 X0 R3 1 +X0/61.5:A BR1019449 CAN Termination IFM E11590 M12 connector 120ohm 0,25W
203 X0 S1 1 +X0/75.0:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
B B
204 X0 S2 1 +X0/75.3:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
205 X0 S3 1 +X0/76.0:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
206 X0 S4 1 +X0/76.3:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
207 X0 S5 1 +X0/75.1:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
208 X0 S6 1 +X0/75.4:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
209 X0 S7 1 +X0/76.1:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
210 X0 S8 1 +X0/76.4:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
211 X0 S9 1 +X0/75.5:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
C C
212 X0 S10 1 +X0/75.7:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
213 X0 S11 1 +X0/76.5:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
214 X0 S12 1 +X0/76.7:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
215 X0 S13 1 +X0/150.3:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
216 X0 S14 1 +X0/150.5:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
217 X0 S16 1 +X0/150.4:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
218 X0 S24 1 +X0/77.0:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
219 X0 S25 1 +X0/78.0:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
D 220 X0 S26 1 +X0/78.5:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104 D
221 X0 S27 1 +X0/77.5:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
222 X0 S28 1 +X0/77.1:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
223 X0 S29 1 +X0/78.1:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
224 X0 S30 1 +X0/78.6:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
225 X0 S31 1 +X0/77.6:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
226 X0 S32 1 +X0/77.3:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
227 X0 S33 1 +X0/78.3:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
228 X0 S34 1 +X0/78.7:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
E E
229 X0 S35 1 +X0/77.7:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
230 X0 S36 1 +X0/77.4:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
231 X0 S37 1 +X0/78.4:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
232 X0 S38 1 +X0/78.8:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
233 X0 S39 1 +X0/77.8:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
234 X0 S40 1 +X0/161.3:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
235 X0 S41 1 +X0/161.5:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
236 X0 S42 1 +X0/161.6:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
237 X0 S43 1 +X0/161.4:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
238 X0 S52 1 +X0/140.5:C BR79693 PROXIMITY SWITCH IFM electronic II5785 M30 SN:22 10-36VDC M12 3WIRE
239 X0 S53 1 +X0/140.6:C BR79693 PROXIMITY SWITCH IFM electronic II5785 M30 SN:22 10-36VDC M12 3WIRE
240 X0 S54 1 +X0/140.3:C BR79693 PROXIMITY SWITCH IFM electronic II5785 M30 SN:22 10-36VDC M12 3WIRE
241 X0 S55 1 +X0/140.4:C BR79693 PROXIMITY SWITCH IFM electronic II5785 M30 SN:22 10-36VDC M12 3WIRE
242 X0 S114 1 +X0/150.6:C BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
B B
243 X0 SS2 1 +X1/55.3:C BR1000374 Box with one hole Telemecanique XALD01 Use with Schneider Style 5 switches
245 X0 SS2 1 +X1/55.3:C BR700651 PILOT BODY ASSEMBLIES TELEMEC ZB4-BZ102 1NC
246 X0 SS2 1 +X1/55.3:C BR70536 Frame +sign plate +engraving 2 lines of 11 characters maximum
247 X0 SS2 1 +X1/55.3:C BR700136 AUXILIARY BLOCK NO TELEMEC ZBE-101 FOR XB4 SWITCH
248 X0 SS2 1 +X1/55.3:C BR1001910 GLAND NUT LAPPKABEL 52103020 FOR GLAND M20
249 X0 SS2 1 +X1/55.3:C BR1023417 GLAND Lappkabel 52104312 M20 / M16 (4,5-10mm)
252 X0 UC1-XP1 1 +X1/30.0:E BR74410 INSERT ODU 309 803 150 037 151 ODU 309 37 POL MALE
253 X0 UC1-XP1 1 +X1/30.0:E BR73523 PLUG ODU 309 ODU 309.020.000.554.000 ODU 309 BAJONETT BRONCE PG42
257 X0 UC1-XP1 1 +X1/30.0:E BR78707 ODU ODU 309.097.001.642.000 COVER FOR BAJONETT SOCKET
258 X0 W2 1 +X0/61.0:C BR76126 PUR Control Cable PURö-JZ 3G1,5 mm² GY HELU 22149 3G 1,5mm²
D 259 X0 W3 1 +X0/61.5:C BR76126 PUR Control Cable PURö-JZ 3G1,5 mm² GY HELU 22149 3G 1,5mm² D
260 X0 W4 1 +X0/63.1:C BR76126 PUR Control Cable PURö-JZ 3G1,5 mm² GY HELU 22149 3G 1,5mm²
261 X0 W54 1 +X0/200.3:C BR1031355 CABLE CONNECTOR IFM EVC080 5m, M12 4P, Angle Male/Open End
262 X0 WA9 1 +X0/60.8:B BR1702908 CABLE CONNECTOR TURCK WKC5701-5M 5m, M12 5P, Angle Female/Open End
263 X0 WHL9 1 +X0/200.3:D BR70396 CABLE CONNECTOR IFM EVC006 Socket, M12 connector, PUR cable / 10 m; 4 x 0.34 mm²
264 X0 WHL10 1 +X0/200.5:D BR70396 CABLE CONNECTOR IFM EVC006 Socket, M12 connector, PUR cable / 10 m; 4 x 0.34 mm²
265 X0 WMA1 1 +X1/32.3:D BR70996 PUR Control Cable PURö-JZ 4G2,5 mm² GY HELU 22166
266 X0 WMA3 1 +X1/30.5:E BR78173 PUR Control Cable PURö-JZ 4G1,5 mm² GY HELU 22150 4G 1,5mm²
267 X0 WPE10PE20 1 +X1/40.0:E BR1700600 Single Strand Cable Helukabel 26906 70mm² Ø 16mm
E E
268 X0 WS1-S5 1 +X0/75.0:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
269 X0 WS2-S6 1 +X0/75.2:D BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
270 X0 WS3-S7 1 +X0/76.0:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
271 X0 WS4-S8 1 +X0/76.2:D BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
272 X0 WS9 1 +X0/75.5:D BR1702950 CABLE CONNECTOR IFM electronic EVC617 3m,M12 4P, Angle Male/Angle Female
273 X0 WS10 1 +X0/75.7:D BR79293 CABLE CONNECTOR IFM EVC033 2m, M12 4P, Angle Male/Angle Female
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
274 X0 WS11 1 +X0/76.5:D BR1702950 CABLE CONNECTOR IFM electronic EVC617 3m,M12 4P, Angle Male/Angle Female
275 X0 WS12 1 +X0/76.7:D BR79293 CABLE CONNECTOR IFM EVC033 2m, M12 4P, Angle Male/Angle Female
276 X0 WS13-S16 1 +X0/150.3:D BR1023808 Y connection cable, AC/DC, Free from halogen IFM EVC620 PUR cable / 4 m; 4 x 0.34 mm²
277 X0 WS14-S114 1 +X0/150.5:D BR1701064 CABLE CONNECTOR IFM EVC519 1m, M12 4P, Straight Male/ 2x Angle Female
278 X0 WS24-S28 1 +X0/77.0:D BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
279 X0 WS25-S29 1 +X0/78.0:D BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
280 X0 WS26-S30 1 +X0/78.5:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
281 X0 WS27-S31 1 +X0/77.5:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
B B
282 X0 WS32-S36 1 +X0/77.2:D BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
283 X0 WS33-S37 1 +X0/78.2:D BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
284 X0 WS34-S38 1 +X0/78.7:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
285 X0 WS35-S39 1 +X0/77.7:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
286 X0 WS40-S43 1 +X0/161.3:D BR1023810 CABLE CONNECTOR IFM EVC621 5m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
287 X0 WS41-S42 1 +X0/161.5:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
288 X0 WS52-S53 1 +X0/140.5:D BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
289 X0 WS54-S55 1 +X0/140.3:D BR1023808 Y connection cable, AC/DC, Free from halogen IFM EVC620 PUR cable / 4 m; 4 x 0.34 mm²
C C
290 X0 WX2 1 +X0/61.3:B BR1702882 CABLE CONNECTOR 13M 2x20 2x17 AWG TURCK CABLE CONNECTOR 13M CANopen M12 angle open end Ø8,4 mm / M16
291 X0 WX3 1 +X0/61.8:B BR1702882 CABLE CONNECTOR 13M 2x20 2x17 AWG TURCK CABLE CONNECTOR 13M CANopen M12 angle open end Ø8,4 mm / M16
292 X0 WX4 1 +X0/62.8:B BR1042994 CABLE CONNECTOR Turck WSC-WKC5701-10M 10m, M12 5P, Male Angle/Female Angle
293 X0 WX5 1 +X0/63.8:E BR1042992 CABLE CONNECTOR TURCK WSC-WKC5701-2M 2m, M12 5P, Male Angle/Female Angle
294 X0 WX8 1 +X0/63.5:C BR1042992 CABLE CONNECTOR TURCK WSC-WKC5701-2M 2m, M12 5P, Male Angle/Female Angle
295 X0 WX10 1 +X0/63.8:B BR1700688 CABLE CONNECTOR Turck WSC-WKC5701-3M 3m, M12 5P, Angle Male/Angle Female
296 X0 WX100 1 +X0/64.6:C BR1702911 CABLE CONNECTOR TURCK WSC5701-5M 5m, M12 5P, Male Angle/Open End
297 X0 WXB1 1 +X0/62.4:C BR1702912 CABLE CONNECTOR TURCK WSC5701-10M 10m, M12 5P, Male Angle/Open End
D 298 X0 WXP1 1 +X1/30.0:E BR701222 Multi Core Cable Helukabel H7715992 37G 2,5mm² D
299 X0 WXP2 1 +X1/41.8:B BR76126 PUR Control Cable PURö-JZ 3G1,5 mm² GY HELU 22149 3G 1,5mm²
300 X0 WXP21 1 +X0/61.0:E BR701118 Multi Core Cable Helukabel 22550 12G 2,5 mm²
301 X0 WXP27 1 +X1/55.3:C BR76291 Multi Core Cable HELU 22151 PUR Control Cable PURö-JZ 5G1,5 mm² GY
302 X0 WY1-Y2 1 +X0/132.2:C BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
303 X0 WY3-Y4 1 +X0/132.4:C BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
304 X0 WY5-Y6 1 +X0/132.6:C BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
305 X0 WY7-Y8 1 +X0/80.0:B BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
306 X0 WY9-Y10 1 +X0/133.2:C BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
E E
307 X0 WY11-Y12 1 +X0/133.4:C BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
308 X0 WY13-Y14 1 +X0/133.6:C BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
309 X0 WY15-Y16 1 +X0/80.3:B BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
310 X0 WY25-Y26 1 +X0/80.5:B BR701219 CABLE CONNECTOR MURR Elektronik 7000-41551-6370200 2m, 2xForm A 200mm/M12, 24Vdc LED Suppressor/ Angle Male
311 X0 WY27-Y28 1 +X0/80.7:B BR701219 CABLE CONNECTOR MURR Elektronik 7000-41551-6370200 2m, 2xForm A 200mm/M12, 24Vdc LED Suppressor/ Angle Male
312 X0 X2 1 +X0/61.0:A BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F01_001_V1.02
Parts list
Pos Unit Item Qty Page Part number Description Manufacturer Order number / Technical characteristics
A A
313 X0 X3 1 +X0/61.5:A BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
314 X0 X4 1 +X0/63.1:A BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
315 X0 X5 1 +X0/64.1:A BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
317 X0 X8 1 +X0/63.5:A BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
319 X0 X10 1 +X0/63.7:C BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
320 X0 X10 1 +X0/63.7:C BR700563 GLAND PLUG MILTRONIC 5210 3110 M16
B B
321 X0 XB0 1 +X0/62.0:B BR1017259 CAN Distribution TURCK ZS5052-4500 4outputs M12 IP67
322 X0 XP2 1 +X1/41.8:B BR70883 KARL DOSE KARL DOSE LEV:KARL DOSE HBG
323 X100 X100 1 +X0/61.7:D BR1188994 Cabinet MHC X100 Bromma BR1188994 316L, T=2, C/C 430x150
324 X100 X100 1 +X0/61.7:D BR1007512 GLAND DIX LAPPKABEL 53325260 M25 2X6mm
325 X100 X100 1 +X0/61.7:D BR1001911 GLAND NUT LAPPKABEL 52103030 FOR GLAND M25
326 X100 X100 1 +X0/61.7:D BR701018 GLAND MS-M25 9-17mm Skintop 12 58 13 M25x1.5
327 X200 HL1 / SW1 1 +X1/57.6:A BR1000722 PILOT LIGHT BLOCK TELEMEC ZB5-AVB5 Complete bodie 24vdc Orange
328 X200 HL1 / SW1 1 +X1/57.6:A BR1000738 Lamp Head TELEMEC ZB5-AV053 Yellow
C C
329 X200 HL1 / SW1 1 +X1/57.6:A BR70536 Frame +sign plate +engraving 2 lines of 11 characters maximum
330 X200 SB6 1 +X1/57.1:A BR700130 PUSH BUTTON Schneider Electric XB4BA21 1 NO, unmarked, Complete push-button
331 X200 SB7 1 +X1/57.2:A BR700130 PUSH BUTTON Schneider Electric XB4BA21 1 NO, unmarked, Complete push-button
332 X200 SB8 1 +X1/57.3:A BR700130 PUSH BUTTON Schneider Electric XB4BA21 1 NO, unmarked, Complete push-button
333 X200 SW1/HL1 1 +X1/56.2:B BR1704387 Orange illumited selector switch head Ø22 2-position stay put 24VDC Schneider Electric XB5AK125B5 Complete assy with ZB5AW0B55 + ZB5AK1253
334 X200 SW2 1 +X1/56.3:B BR701419 SELECTOR SWITCH Schneider Electric XB4BD33 2xNO 3-STAY PUT
335 X200 SW3 1 +X1/56.5:B BR701419 SELECTOR SWITCH Schneider Electric XB4BD33 2xNO 3-STAY PUT
336 X200 SW4 1 +X1/56.7:B BR701419 SELECTOR SWITCH Schneider Electric XB4BD33 2xNO 3-STAY PUT
D 337 X200 SW5 1 +X1/57.4:A BR701419 SELECTOR SWITCH Schneider Electric XB4BD33 2xNO 3-STAY PUT D
338 X200 X200 1 +X1/56.1:A BR700172 JUNCTION BOX 8 HOLES TELEMECANIQUE XAPA 2108
339 X200 X200 1 +X1/56.1:A BR701019 GLAND MS-M32 11-21mm SKINTOP 12 58 14 M32x1.5
340 X200 X200 1 +X1/56.1:A BR1001912 GLAND NUT LAPP FOR GLAND M32
341 X200 X200 1 +X1/56.1:A BR1236709 EH170U Liebherr Control Box Sticker - EH170U Liebherr Control Box Sticker
342 X200 X200 1 +X1/56.1:A BR701018 GLAND MS-M25 9-17mm Skintop 12 58 13 M25x1.5
343 X200 X200 2 +X1/56.1:A BR1001911 GLAND NUT LAPPKABEL 52103030 FOR GLAND M25
345 X200 X200 1 +X1/56.1:A BR1009870 GLAND ENLARGER M25 / M32 LAPPKABEL 12 67 76 ME - M25 / M32
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
W18 GN
W18 YE
W18 GY
W18 PK
W18 GN/YE
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WB1 02/WH
WB1 03/WH
WB1 04/WH
WB1 05/WH
WB1 09/WH
WB1 11/WH
WB1 12/WH
WB1 14/WH
C WB1 15/WH C
WB1 17/WH
WB1 18/WH
WB1 25/n.c.
WB1 31/BN
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WB1 40/GY
WB1 43/n.c.
WB1 48/WH
C WB1 49/BU C
WB1 51
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WX17 GN
WX17 YE
WX17 GY
WX17 PK
WX17 GN/YE
C C
+X1 X17 X1:SH. WX17 SH 24 +X1 PE65_1 +X0/65.3:E
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
Multi Core Cable 18x1,5mm² PUR BR76945 10 m
+X200SW1/HL1 13 WX200 1 + +X100 X2 /56.1:C
+X200
HL1 / SW1 X2 WX200 14 - +X100 X2 /57.6:D
+X200
HL1 / SW1 X1 WX200 15 48 +X100 X3 /57.7:D
WX200 16
WX200 17
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WXP23 4
WXP23 5
WXP23 6
WXP23 10
WXP23 11
WXP23 12
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WXP23 PE
W2 GNYE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
PUR Control Cable PURö-JZ 3G1,5 mm² GY 3G 1,5mm² BR76126 15 m
+X0 X3 XE07 W3 1 3 +X100 X1 /61.5:D
W4 GNYE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
CABLE CONNECTOR 5m, M12 4P, Angle Male/Open End BR1031355 5m
D +X0 X10 XP2:1 W54 BN +X100 5 /200.3:C D
WA9 RD
E E
WA9 BK
WA9 WH
WA9 BU
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WS9 WH
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WS11 WH
B WS12 WH B
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WS94 WH
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WXP1 2
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WXP2 GNYE
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
Multi Core Cable 12G 2,5 mm² BR701118 9m
+X100 X1 1 WXP21 1 1 +X1 XP21 +X1/40.8:E
B WXP21 5 B
WXP21 10
WXP21 11
WXP27 2
WXP27 3
WXP27 4
WXP27 GN/YE
WY1-Y2 GN/YE
E Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column E
Conductor
from point name point to
CABLE CONNECTOR 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ BR1018339 1.5 m
+X0 Y3-Y4 B1 WY3-Y4 BK2 XP6:2 +X0 X2 /132.5:B
WY3-Y4 GN/YE
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WY5-Y6 GN/YE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
CABLE CONNECTOR 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ BR1018339 1.5 m
+X0 Y7-Y8 B1 WY7-Y8 BK2 XP2:2 +X0 X2 /80.2:B
WY7-Y8 GN/YE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
CABLE CONNECTOR 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ BR1018339 1.5 m
+X0 Y9-Y10 B1 WY9-Y10 BK2 XP4:2 +X0 X3 /133.3:B
WY11-Y12 GN/YE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
D from point name point to D
CABLE CONNECTOR 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ BR1018339 1.5 m
+X0 Y13-Y14 B1 WY13-Y14 BK2 XP8:2 +X0 X3 /133.7:B
WY13-Y14 GN/YE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
CABLE CONNECTOR 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ BR1018339 1.5 m
+X0 Y15-Y16 B1 WY15-Y16 BK2 XP2:2 +X0 X3 /80.4:B
E E
+X0 Y15-Y16 A1 WY15-Y16 BK1 XP2:4 +X0 X3 /80.3:B
WY15-Y16 GN/YE
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
WY25-Y26 GN/YE
Target Designation Connection Cable Connection Target Designation Cable type Part number Cable length Page / column
Conductor
from point name point to
CABLE CONNECTOR 2m, 2xForm A 200mm/M12, 24Vdc LED Suppressor/ BR701219 1.5 m
+X0 Y27-Y28 B1 WY27-Y28 BK2 XP4:2 +X0 X4 /80.8:B
WY27-Y28 GN/YE
C C
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
F08_001_V3
Cable assignment diagram CAN BUS CABLE
Cable name Length Source Target Page / column
A A
+X1-WX17 2 +X1-X1 +X1-X17 +X0/65.1:D
+X1-PE65_1
REMARK : All these images are for illustration purposes only. +X0-WX10 3 +X0-WX10 +X0-WX10 +X0/63.8:B
C C
1. Shield
2. 24 V DC / + VBB (RED WIRE COLOUR)
3. 0 V DC / GND (BLACK WIRE COLOUR)
4. CAN_H (WHITE WIRE COLOUR)
5. CAN_L (BLUE WIRE COLOUR)
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Sensor cable, Y-split cable Cable S1 (A) & S2 (B) M12 Socket +X0-WS1-S5 3 +X0-S1 +X0-X2 +X0/75.0:D
A A
+X0-S5
Pin 1 / 24 V DC
+X0-S30
+X0-S31
+X0-S38
+X0-S39
+X0-S42
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
1 1 pcs BR1705369 1 Phase Switched-mode power supply 24 V DC IFM ZB0807 Output current 20 A, regulated
2 8 Pcs BR1701598 ALOFREE CABLEDUCT 37.5X75 Black Canalplast PA037N Halogen Free Trunking
3 2 Pcs BR1701599 ALOFREE CABLEDUCT 50X75 Black Canalplast PA057N Halogen Free Trunking
4 1 Pcs BR700871 AUXILIARY BLOCK Baco 172179 NO+NC 400V 10A SIGNALCONTACT
5 2 Pcs BR1019811 AUXILIARY BLOCK BACO 331E10 switch body with 1NO block
B 6 1 Pcs BR1000712 AUXILIARY BLOCK TELEMEC ZB5-AZ105 switch body with 1 NC and 1NO block B
9 2 Pcs BR700131 Auxiliary block Schneider Electric ZBE102 Single contact block for head Ø22 1NC
11 2 Pcs BR1188037 Blanking plate with rubber gasket Bromma BR1188037 Assy
C 12 1 Pcs BR1000374 Box with one hole Telemecanique XALD01 Use with Schneider Style 5 switches C
14 5 Pcs BR1031355 CABLE CONNECTOR IFM EVC080 5m, M12 4P, Angle Male/Open End
15 2 Pcs BR1702908 CABLE CONNECTOR TURCK WKC5701-5M 5m, M12 5P, Angle Female/Open End
16 2 Pcs BR70396 CABLE CONNECTOR IFM EVC006 Socket, M12 connector, PUR cable / 10 m; 4 x 0.34 mm²
17 8 Pcs BR1023806 CABLE CONNECTOR IFM electronic EVC619 3m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
18 6 Pcs BR1023804 CABLE CONNECTOR IFM EVC618 2m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
D D
19 2 Pcs BR1702950 CABLE CONNECTOR IFM electronic EVC617 3m,M12 4P, Angle Male/Angle Female
20 2 Pcs BR79293 CABLE CONNECTOR IFM EVC033 2m, M12 4P, Angle Male/Angle Female
21 1 Pcs BR1701064 CABLE CONNECTOR IFM EVC519 1m, M12 4P, Straight Male/ 2x Angle Female
22 1 Pcs BR1023810 CABLE CONNECTOR IFM EVC621 5m, M12 4P, Straight Male/ 2x Angle Female (pin2,4 bridge)
23 1 Pcs BR1042994 CABLE CONNECTOR Turck WSC-WKC5701-10M 10m, M12 5P, Male Angle/Female Angle
24 2 Pcs BR1042992 CABLE CONNECTOR TURCK WSC-WKC5701-2M 2m, M12 5P, Male Angle/Female Angle
E E
25 1 Pcs BR1700688 CABLE CONNECTOR Turck WSC-WKC5701-3M 3m, M12 5P, Angle Male/Angle Female
26 1 Pcs BR1702911 CABLE CONNECTOR TURCK WSC5701-5M 5m, M12 5P, Male Angle/Open End
27 1 Pcs BR1702912 CABLE CONNECTOR TURCK WSC5701-10M 10m, M12 5P, Male Angle/Open End
28 8 Pcs BR1018339 CABLE CONNECTOR MURR 7000-41511-6370150 1,5m, 2xForm A 110mm/M12, 24Vdc LED Suppressor/ Angle Male
29 2 Pcs BR701219 CABLE CONNECTOR MURR Elektronik 7000-41551-6370200 2m, 2xForm A 200mm/M12, 24Vdc LED Suppressor/ Angle Male
MACHINE TYPE: SHEET
EH 170U 500
F This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 501
Date
Ed.
20/9/2019
ZAMZUMO
The design and/or constructions
contained therein, may not be copied
CHECKED BY: Summarized parts list: TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
30 2 Pcs BR1702882 CABLE CONNECTOR 13M 2x20 2x17 AWG TURCK CABLE CONNECTOR 13M CANopen M12 angle open end Ø8,4 mm / M16
33 2 Pcs BR1019449 CAN Termination IFM E11590 M12 connector 120ohm 0,25W
34 6 Pcs BR1700599 CANopen I/O MODULE IFM CR9057 8 in / 8 out + M12 CANopen connectors
36 1 Pcs BR1001828 CIRCUIT BREAKER 230/400V 6KA, 1-POLE, C, 2A, D=70MM SIE 5SY6102-7
C 41 2 Pcs BR79125 CURRENT RELAY SR15 SEW 8267626 BSR 150-500VAC M25 C
42 1 Pcs BR1245221 Cabinet EH5U/EH170U SCS4/MidR Bromma BR1245221 T=2, Material SS 1.4404, IP 66
43 1 Pcs BR1188994 Cabinet MHC X100 Bromma BR1188994 316L, T=2, C/C 430x150
51 8 Pcs BR1703554 End cap PXC 1206573 TS 35 / DIN rail protection cap
53 8 Pcs BR1028254 End cover PXC 3031762 Separator plate for STS 2,5-TWIN
E E
54 100 Pcs BR75637 FERRULE 1,5 NO ISOL.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
59 1 Pcs BR79371 FUSE LITTELFUSE 33-051-82 Blade fuse 30A
85 1 Pcs BR79282 GLAND PLUG MURR Elektronik 40 57 05 ASB BOX PLUGS M12
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
88 1 Pcs BR1000727 GLAND SR-M50x1.5 32-38mm Skindicht 52106610
91 1 Pcs BR1704390 Harness for CR0032 Connector AMP 55-pole Boomerang Cable OU
92 1 pcs BR1705917 Heater Stego 06000.0-00 50W, TS35, IP20, AC/DC 120 – 240 V
96 1 Pcs BR1704540 Housing HAR 19300241542 Side entry M32x1, Harting 24P
101 1 Pcs BR74410 INSERT ODU 309 803 150 037 151 ODU 309 37 POL MALE
103 1 Pcs BR70848 Insert HAR 09330102601 Harting 1-10P+PE Screw terminals
105 1 Pcs BR70883 KARL DOSE KARL DOSE LEV:KARL DOSE HBG
D D
106 2 Pcs BR1701085 LED'S & LAMPS WITH COLOR CODES TURCK 3026639 GREEN Color PWM
107 2 Pcs BR1701086 LED'S & LAMPS WITH COLOR CODES TURCK 3026666 RED Color PWM
108 2 Pcs BR1701089 LED'S & LAMPS WITH COLOR CODES TURCK 3026716 WHITE Color PWM
109 2 Pcs BR1701088 LED'S & LAMPS WITH COLOR CODES TURCK 3026667 YELLOW Color PWM
110 2 Pcs BR1701087 LED'S & LAMPS WITH COLOR CODES TURCK 3026668 BLUE Color PWM
115 3 Pcs BR1704671 Legend holder Schneider Electric ZBZ34 For harmony series XB5,
116 1 Pcs BR1001829 MAIN CIRCUIT BREAKER SIEMENS 5SY6 210-7 C-CHARACTER
MACHINE TYPE: SHEET
EH 170U 503
F This drawing is copyright, and is SERIAL NO.
Sociedad Portuaria S.A. CONT.
F
the property of BROMMA CONQUIP. SN 30874 504
Date
Ed.
10/10/2019
ZAMZUMO
The design and/or constructions
contained therein, may not be copied
CHECKED BY: Summarized parts list: TOTAL SH.
108
Appr or reproduced, whitout the written DRAWN BY:
ZAMZUMO PLANT (=)
A1 PLOTTED: DRAWING NO. REV.
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
117 1 Pcs BR700868 MAIN CIRCUIT BREAKER Baco 0172200 50A
118 1 Pcs BR1707005 Modem Datarespons 801622 2xCAN selecttable 120Ohm, Ethernet 10/100 Mbit, WIFI, GPS,2xGSM
119 1 pcs BR1707013 Modem Power & Data Connector Boomerang Cable OU BR1707013 2,5m female type AMP 35pin for power/2xCAN/Ethernet
120 1 pcs BR1705892 Monitoring relay Omron K8DT-PH1CN 3 phase, phase sequence & phase loss 200-480 VAC
121 10.00 m BR76945 Multi Core Cable Helukabel 22540 18x1,5mm² PUR
B 122 9.00 m BR78703 Multi Core Cable Helukabel 22542 25G 1,5mm² B
123 8.00 m BR701222 Multi Core Cable Helukabel H7715992 37G 2,5mm²
124 10.00 m BR76291 Multi Core Cable HELU 22151 PUR Control Cable PURö-JZ 5G1,5 mm² GY
125 9.00 m BR701118 Multi Core Cable Helukabel 22550 12G 2,5 mm²
126 26 Pcs BR701381 NUT LOC-KING M4 BROMMA BR701381 DIN 985, A4, KLASS 70
127 4 Pcs BR77889 NUT LOC-KING M5 BROMMA BR77889 DIN 985, A4, KLASS 70
C 128 1 Pcs BR78707 ODU ODU 309.097.001.642.000 COVER FOR BAJONETT SOCKET C
131 1 Pcs BR1704387 Orange illumited selector switch head Ø22 2-position stay put 24VDC Schneider Electric XB5AK125B5 Complete assy with ZB5AW0B55 + ZB5AK1253
134 1 Pcs BR1000722 PILOT LIGHT BLOCK TELEMEC ZB5-AVB5 Complete bodie 24vdc Orange
D D
135 1 Pcs BR73523 PLUG ODU 309 ODU 309.020.000.554.000 ODU 309 BAJONETT BRONCE PG42
136 4 Pcs BR79693 PROXIMITY SWITCH IFM electronic II5785 M30 SN:22 10-36VDC M12 3WIRE
137 36 Pcs BR1702972 PROXIMITY SWITCH M30 IFM electronic II5975 IIA3015BBPKG/US-104
138 37.00 m BR76126 PUR Control Cable PURö-JZ 3G1,5 mm² GY HELU 22149 3G 1,5mm²
139 16.00 m BR78173 PUR Control Cable PURö-JZ 4G1,5 mm² GY HELU 22150 4G 1,5mm²
140 5.00 m BR70996 PUR Control Cable PURö-JZ 4G2,5 mm² GY HELU 22166
E E
141 3 Pcs BR700130 PUSH BUTTON Schneider Electric XB4BA21 1 NO, unmarked, Complete push-button
142 2 Pcs BR1703273 Plank Type III IFM ZZ7059 16 independent Delcon I/O
143 1 Pcs BR1040676 Plug-in bridge PXC 3030284 TERMINAL JUMPER FOR TERMINAL FUSE
144 1 Pcs BR1029845 Programmable mobile controller type R 360 IFM CR0032 16 inputs / 16 outputs
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
146 1 Pcs BR1703557 Relay retaining bracket PXC 2905984 For 2 & 4 Switching
147 1 Pcs BR1703194 Relay socket PXC 2833563 For 2 & 4 switching relay
148 4 Pcs BR75331 SCREW M6S 5x12 Bromma BR75331 FZB, CLASS 8.8, ISO 4014
149 12 Pcs BR79928 SCREW MC6S 4x16 Bromma A4, CLASS 70, ISO 4762
150 8 Pcs BR1029642 SCREW MC6S M4x12 BROMMA BR1029642 FZB 8.8
B 151 4 Pcs BR75606 SCREW MC6S M4x16 BROMMA BR75606 FZB 8.8 B
152 2 Pcs BR1023817 SCREW MC6S M4x25 BROMMA BR1023817 FZB 8.8
155 4 Pcs BR701419 SELECTOR SWITCH Schneider Electric XB4BD33 2xNO 3-STAY PUT
160 2 Pcs BR1019832 SWITCH HEAD BACO L21KA03 Only operating head 2 pos, 45º, Ø22,5 mm
168 5.00 m BR1700600 Single Strand Cable Helukabel 26906 70mm² Ø 16mm
169 1 Pcs BR1703188 Single relay PXC 2903660 Single relay 2-pole
E E
170 2 Pcs BR1701780 Split cable TURCK V9-7/4WK 4.4T-0,3/0,3/0,3/0,3/S90/CS14252 1x7m open end / 4x0,3m M12 female
173 63 Pcs BR1028250 TERMINAL 2,5mm² Phoenix Contact 3031720 3-CONDUCTOR GRAY
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
Position Quantity Unit Part number Designation Manufacturer Order number Technical characteristics
A A
175 9 Pcs BR1028258 TERMINAL JUMPER Phoenix Contact 3030190 5-WAY
181 1 Pcs BR79043 THERMAL-MAGNETIC CIRCUIT BREAK Siemens 3RV2011-1HA10 3,0kW 5,5-8A
182 1 Pcs BR78993 THERMAL-MAGNETIC CIRCUIT BREAKER SIEMENS 3RV2021-4BA10 7.5KW 14-20A
183 1 Pcs BR1010842 TRIGGER ACTION BUTTON BLACK TELEMEC ZB5-AS52 BLACK Ø40 TURN RELEASE
185 24 Pcs BR701380 WASHER BRB 4,3x9x0,8 Bromma BR701380 A4, ISO 7089
C 186 6 Pcs BR77896 WASHER BRB 5,3x10x1 Bromma BR77896 A4, ISO 7089 C
190 2 Pcs BR1023808 Y connection cable, AC/DC, Free from halogen IFM EVC620 PUR cable / 4 m; 4 x 0.34 mm²
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
TS 35 C/20 BR71986
1 ST 4-FSI/C BR1028263 6
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
5A
30A
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
204 BR1028258
205
206 BR1028258
C 207 C
208 BR1028258
209
210 BR1028258
213 BR1028258
D D
FBS 5-5 BR1028258 0 BR1028258
214
215 BR1028258
216
217 BR1028258
E E
FBS 5-5 BR1028258 0 BR1028258
218
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
L1
L2
L3
102
104
E E
109 STTBS 2,5 BR1028259 2.5
110
112
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
114
B 116 B
200
201
202
203
120
122
124
128
130
134
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
C C
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
B B
C C
D D
E E
0 1 2 3 4 5 6 7 8 9
0 1 2 3 4 5 6 7 8 9
44
45
46
B 47 B
48
50
51
52
53
C 54 C
60
61
62
D D
E E
0 1 2 3 4 5 6 7 8 9
Page 1 of 1
0-1-may 02 rev.00 Bromma Conquip
Bromma Manual
3 Bromma 2018-08
Bromma Manual
1.1 Warnings
HAZARD! Always disconnect the power supply before work is carried
out!
Care must be taken when operating the spreader from the SCU main
unit. It must be carried out under extreme caution and by personnel
familiar with risks related to spreader function and movements.
Serious injury by crushing can occur.
2018-08 Bromma 4
Bromma Manual
5 Bromma 2018-08
Bromma Manual
1.3 Components
1.3.1 PLC (CR0032)
The PLC (CR0032) is a freely programmable controller developed by
IFM. The PLC (CR0032) has 16 inputs / 16 outputs and 4 CAN
interfaces and serves as the controller in the SCU system.
All necessary input signals for running the spreader will either be
available through the configurable I/O’s or via CAN.
Communication with the crane will either run using BCAN, ZCAN or
DS444.
The CAN interfaces used are as follows:
CAN1 Spreader CAN network
2018-08 Bromma 6
Bromma Manual
Note!
For further information on fault finding, please refer
to Bromma service personnel.
7 Bromma 2018-08
11 • Fault finding diagnostics
WEIGHT
1 lb = 0,4536 kg
1 kg = 2,2046 lb
1 ton = 1 t = 2000 lb = 907 kg = 0,893 Lt= 0,907 tonne
1 Lt = 2240 lb = 1016 kg = 1,016 tonne = 1,120 ton
1 tonne = 1 mT = 2204 lb = 1000 kg = 0,9842 Lt = 1,103 ton
VOLUME
1l = 0,21997 UKgal = 0,26417 USgal
PRESSURE
1 bar = 10 N/cm2 = 1,02 Kp/cm2 = 14,503 lbf/in2
POWER
1 Hp = 0,746 kW
1 kW = 1,341 Hp
TORQUE
1 Kpm = 9,81 Nm = 7,233 lbf
FORCE
1 Kgf = 1 kp = 9,81 N = 2,2046 lbf
TEMPERATURE
dgr C = 5 • (dgr F-32)
9
A = ampere l = litre
o
C = degrees centigrade lb = pound
c/s = cycles per second lbf= pound force
o
F = degrees Fahrenheit m = meter
ft = foot min= minute
gal = gallon n = newton
Hp = horse power s = second
Hz = hertz t = tonne
in = inch v = volt
kg = kilogramme w = watt
Kgf = kilopond force µm = micron