Professional Documents
Culture Documents
300
UNIT NO. 670-45
PN. 670-45 THRU 95
DATE 08-13-00
PAGE 1 OF 7
SPECIFICATION GUIDE
ARROWDRILL SEAL BORE PACKER
RECOMMENDED MIN. BORE
CASING PACKER
The Arrowdrill Production Packers are versatile high performance permanent packers designed for high CASING RANGE THROUGH PRODUCT
differential pressure and hostile environment applications. Seal Bore Packers may be set wireline or O.D WEIGHT MIN. MAX. O.D. BORE SEALS NUMBER
o
hydraulically. One piece slips eliminate premature setting. Element metal back-up rings provide 360 casing (IN./MM) (LB./FT.) (IN./MM) (IN./MM) (IN./MM) (IN./MM) (IN./MM.)
contact to prevent rubber extrusion at high temperature and pressure. 5 4.156 4.408 3.968 2.688 1.938
127,00
15.0 - 21.0 105,56 111,96 100,79 68,28 49,23
670-50-26
Applications include: stimulation jobs where excessively high pressure and/or temperatures are encountered. 5 4.156 4.408 3.968 2.390 1.703
By installing a Knock-Out, Pump-Out or Screw-Out Plug, the Arrowdrill may be used as a temporary bridge 127,00
15.0 - 21.0 105,56 111,96 100,79 60,71 43,26
670-50-23
plug to isolate a lower zone. The zone may later be produced by removing the plug with the production string 5-1/2 4.548 4.670 4.250 2.688 1.938
and landing the seals. A left hand release On-Off Tool with a wireline plug profile may be run above the latch 139,70
23.0 - 26.0 115,52 118,62 107,95 68,28 49,23
670-57-26
sub of the Seal Assembly. Setting a wirline plug in the profile converts the packer to a bridge plug and allows
5-1/2 4.670 4.892 4.437 2.688 1.938
removal of the tubing string without having to kill the well. 139,70
17.0 - 23.0 118,62 124,26 112,70 68,28 49,23
670-56-26
Special precautions need to be taken into consideration when using the Arrowdrill: 5-1/2 4.892 5.044 4.563 3.000 2.375 / 2.270
139,70
13.0 - 17.0 124,26 128,12 115,90 76,20 60,33/ 57,66
670-55-30
• The Arrowdrill Packers contain steel mandrels and therefore must be milled over to remove from the well.
6-5/8 5.675 6.135 5.687 4.000 3.000
• Any part that is run through an Arrowdrill Packer should be at least 1/16” smaller than the packer bore. 17.0 - 32.0 670-72-40
• Recommended running speed no faster than 180 ft./min. 168,28 144,15 155,83 144,45 101,60 76,20
• Slow down when entering a liner. 7 6.094 6.366 5.687 2.688 1.938
177,80
23.0 - 32.0 154,79 161,70 144,45 68,28 49,23
670-71-26
• After the wireline packer is made up on the setting tool and is ready to run in the well, use caution when
picking up the string as not to damage the packer strips. 7 5.920 6.094 5.468 3.250 2.406
177,80
32.0 - 38.0 150,37 154,79 138,89 82,55 61,11
670-72-32
Seal Bore Packers may be set wireline or hydraulically. One-piece slips eliminate
premature setting. Element metal back-up rings provide 360° casing contact to
prevent rubber extrusion at high temperature and pressure.
Applications:
Stimulation jobs where excessively high pressure and/or temperatures are encountered.
By installing a Knock-Out, Pump-Out or Screw-Out Plug, the Arrowdrill may be used
as a temporary bridge plug to isolate a lower zone. The zone may later be produced
by removing the plug with the production string and landing the seals.
A left-hand release On-Off Tool with a wireline plug profile may be run above the latch
sub of the Seal Assembly. Setting a wireline plug in the profile converts the packer to a
bridge plug and allows removal of the tubing string without having to kill the well.
Features:
• Meets NACE Standard MR0175 for H 2S service
• Elastomer options available for hostile environments
• Material options available for high pressure and/or hostile environments
• Wireline or hydraulic setting options
• One-piece slip eliminates premature setting
• Element back-up system prevents rubber extrusion
• B Arrowdrill, jay or threaded latch options
Special precautions need to be taken into consideration when using the Arrowdrill:
• The Arrowdrill Packers contain steel mandrels and therefore must be milled
to remove from the well
• Any part that is run through an Arrowdrill Packer should be at least 1/16” smaller
than the packer bore
• Recommended running speed no faster than 180 ft/min
• Slow down when entering a liner hanger
• After the wireline packer is made up on the setting tool and is ready to run in the
well, use caution when picking up the string as not to damage the packer slips
© 2000 WEATHERFORD. All Rights Reserved. Houston, TX USA • Ph 713/693-4000 • 800/257-3826 • Fax 713/693-4441
© 2000 WEATHERFORD. All Rights Reserved. Houston, TX USA • Ph 713/693-4000 • 800/257-3826 • Fax 713/693-4441
57
© 2000 WEATHERFORD This document is the confidential property of Weatherford International, Inc. and may not be reproduced
in any way, either whole or in part, or distributed without the expressed written authorization of Weatherford International, Inc.
INDEX NO. 300
UNIT NO. 670-45
PN. 670-45 THRU 95
DATE 08-13-00
PAGE 3 OF 7
SHEAR PIN
© 2000 WEATHERFORD This document is the confidential property of Weatherford International, Inc. and may not be reproduced
in any way, either whole or in part, or distributed without the expressed written authorization of Weatherford International, Inc.
INDEX NO. 300
UNIT NO. 670-45
PN. 670-45 THRU 95
DATE 08-13-00
PAGE 4 OF 7
ASSEMBLY: 5-1/2” THRU 9-5/8” THREAD LATCH PACKER WIRELINE SETTING KIT SHEAR PIN
SHEAR PIN VALUE
FOR BAKER #20 (OR EQUIVALENT) PRESSURE SETTING ASSEMBLY 5-1/2" - 7-5/8"
5/16 X 5/8"
EACH PIN (LBS.)
1.) Screw inner adapter (5) into inner adapter cap (7) and install socket set screws (6). X08-20-040
2.) Grease seal bore of packer. 5/16 X 1"
3.) Slide inner adapter cap (7) into top connection of packer, align holes in top connection with holes in inner 9-5/8" 5,000
X08-20-064
adapter cap (7). Install shear pins.
4.) Slide setting sleeve (3) onto pressure setting assembly.
5.) Screw outer adapter (1) onto cross-link sleeve of pressure setting assembly. Wrench tight. 5-1/2” – 9-5/8” ARROWDRILL THREAD-LATCH SETTING ADAPTER
6.) Attach packer to pressure setting assembly by screwing inner adapter (5) onto setting mandrel of setting KIT FOR BAKER #20 PRESSURE SETTING ASSEMBLY
assembly. Install set screws (4).
7.) Slide setting sleeve (3) over outer adapter (1) and screw setting sleeve down until it contacts lock nut CASING PKR.
housing on the packer. Hand tight only. DO NOT TIGHTEN WITH A WRENCH. Install set screws (2) DIMENSIONS (IN.)
O.D. BORE
into setting sleeve (3).
(IN.) (IN.) A B C D E F
5-1/2 2.688 17.000 2.750 4.438 3.316 4.000 2.750
PARTS LIST: 5-1/2” THRU 9-5/8” WIRELINE SETTING KIT—ARROWDRILL
5-1/2 3.000 17.000 3.000 4.438 3.316 4.000 2.750
5-1/2" 6-5/8", 7", 7-5/8" 6-5/8 2.688 22.875 4.000 5.468 3.316 5.000 2.875
Itm. Qty. DESCRIPTION
2.688" 3.00" 2.688" 3.25" 4.00" 6-5/8 3.250 22.875 4.000 5.468 3.316 5.000 2.875
COMPLETE 580-55-001 581-55-001 580-71-003 580-70-001 580-70-001 6-5/8 4.000 26.125 4.000 5.468 3.316 5.250 2.875
ASSEMBLY *670-55-26WKT *670-55-30WKT *670-71-26WKT *670-70-32WKT *670-70-40WKT 7 2.688 22.875 4.000 5.468 3.316 5.000 2.875
1 1 OUTER ADAPTER 581-55-102 581-55-102 580-70-102 580-70-102 580-70-102 7 3.250 22.875 4.000 5.468 3.316 5.000 2.875
3/8-16 X 3/8" 3/8-16 X 3/8" 3/8-16 X 3/8" 3/8-16 X 1/2" 3/8-16 X 3/8"
2 3 SET SCREW 7 4.000 26.125 4.000 5.468 3.316 5.250 2.875
003-C6-006 003-C6-006 003-C6-006 003-C6-008 003-C6-006
3 1 SETTING SLEEVE 855-55-470 855-55-470 580-70-470 580-70-470 861-70-470 7-5/8 3.250 22.875 4.000 5.468 3.316 5.250 2.875
3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 1/2" 7-5/8 4.000 26.125 4.000 5.468 3.316 5.250 2.875
4 3 SET SCREW
003-C6-008 003-C6-008 003-C6-008 003-C6-008 003-C6-008 9-5/8 3.250 27.188 4.000 8.000 3.316 7.750 2.183
5 1 INNER ADAPTER 595-55-461 595-55-461 780-70-461 780-70-461 780-70-461 9-5/8 4.000 27.188 4.000 8.000 3.316 7.750 2.938
1/4-20 X 3/8" 1/4-20 X 3/8" 1/4-20 X 5/8" 3/8-16 X 3/8" 1/4-20 X 3/4" 9-5/8 4.750 27.188 4.000 8.000 3.316 7.750 2.938
6 3 SET SCREW
003-C4-006 003-C4-006 003-C4-010 003-C5-006 003-C4-012
9-5/8 6.000 26.000 4.000 8.200 3.316 8.000 2.938
7 1 INNER ADAPTER CAP 855-55-104 855-55-103 580-71-462 580-70-465 861-70-462
9-5/8"
Itm. Qty. DESCRIPTION
3.25" 4.00" 4.75" 6.00"
COMPLETE 580-95-005 582-95-TLC 580-95-TLC 870-95-000
ASSEMBLY *670-95-32WKT *670-95-40WKT *670-95-47WKT *670-95-60WKT
1 1 OUTER ADAPTER 580-95-102 580-95-102 580-95-102 580-95-102
3/8-16 X 1/2" 3/8-16 X 3/8" 3/8-16 X 3/8" 3/8-16 X 3/8"
2 3 SET SCREW
003-C6-008 003-C6-006 003-C6-006 003-C6-006
3 1 SETTING SLEEVE 580-95-470 580-95-470 580-95-470 870-95-470
3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 3/4"
4 3 SET SCREW
003-C6-008 003-C6-008 003-C6-008 003-C6-012
5 1 INNER ADAPTER 581-95-461 582-95-46T 582-95-46T 870-95-461
6 SET SCREW NOT REQUIRED
7 INNER ADAPTER CAP NOT REQUIRED
*Please use this number when ordering.
© 2000 WEATHERFORD This document is the confidential property of Weatherford International, Inc. and may not be reproduced
in any way, either whole or in part, or distributed without the expressed written authorization of Weatherford International, Inc.
INDEX NO. 300
UNIT NO. 670-45
PN. 670-45 THRU 95
DATE 08-13-00
PAGE 5 OF 7
© 2000 WEATHERFORD This document is the confidential property of Weatherford International, Inc. and may not be reproduced
in any way, either whole or in part, or distributed without the expressed written authorization of Weatherford International, Inc.
INDEX NO. 300
UNIT NO. 670-45
PN. 670-45 THRU 95
DATE 08-13-00
PAGE 6 OF 7
© 2000 WEATHERFORD This document is the confidential property of Weatherford International, Inc. and may not be reproduced
in any way, either whole or in part, or distributed without the expressed written authorization of Weatherford International, Inc.
INDEX NO. 300
UNIT NO. 670-45
PN. 670-45 THRU 95
DATE 08-13-00
PAGE 7 OF 7
ASSEMBLY: 5-1/2” THRU 9-5/8” J-LATCH PACKER WIRELINE SETTING KIT FOR SHEAR PIN
BAKER #20 (OR EQUIVALENT) PRESSURE SETTING ASSEMBLY SIZE PART NUMBER SHEAR PIN VALUE
1.) Screw inner adapter (5) into inner adapter cap (7) and install socket set screws (6). 5/16 X 5/8" EACH PIN (LBS.)
5-1/2" - 7-5/8"
2.) Lubricate seal bore of packer. X08-20-040
3.) Slide inner adapter cap (7) into top connection of packer, align holes in top connection with holes in inner 5/16 X 1"
adapter cap (7). Install shear pins. 9-5/8" 5,000
X08-20-064
4.) Slide setting sleeve (3) onto pressure setting assembly.
5.) Screw outer adapter (1) onto cross-link sleeve of pressure setting assembly. Wrench tight.
6.) Attach packer to pressure setting assembly by screwing inner adapter (5) onto setting mandrel of setting 5-1/2” – 9-5/8”ARROWDRILL J-LATCH WIRELINE SETTING ADAPTER KIT
assembly. Install set screws (4).
7.) Slide setting sleeve (3) over outer adapter (1) and screw setting sleeve down until it contacts lock nut housing CASING PACKER DIMENSIONS (IN.)
on the packer. Hand tight only. DO NOT TIGHTEN WITH A WRENCH. Install set screws (2) into setting O.D. BORE
sleeve (3). A B C D E F
(IN.) (IN.)
5-1/2 2.688 20.750 3.000 4.438 3.316 4.000 2.875
PARTS LIST: 5-1/2” THRU 9-5/8” WIRELINE SETTING KIT—J-LATCH ARROWDRILL
5-1/2 3.000 20.750 3.000 4.438 3.316 4.000 2.875
5-1/2" 6-5/8", 7", 7-5/8" 6-5/8 2.688 26.000 4.000 5.468 3.316 5.000 2.875
Itm. Qty. DESCRIPTION
2.688" 3.00" 2.688" 3.25" 4.00" 6-5/8 3.250 26.000 4.000 5.468 3.316 5.000 2.875
COMPLETE 580-55-001 581-55-001 580-71-002 580-70-001 580-75-001 6-5/8 4.000 26.125 4.000 5.468 3.316 5.250 2.875
ASSEMBLY *670-55-26WKJ *670-55-30WKJ *670-71-26WKJ *670-70-32WKJ *670-70-40WKJ 7 2.688 26.000 4.000 5.468 3.316 5.000 2.875
1 1 OUTER ADAPTER 581-55-102 581-55-102 580-70-102 580-70-102 580-70-102 7 3.250 26.000 4.000 5.468 3.316 5.000 2.875
2 A.R. SET SCREW 3/8-16 X 3/8" 3/8-16 X 3/8" 3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 1/2" 7 4.000 26.125 4.000 5.468 3.316 5.250 2.875
003-C6-006(3) 003-C6-006(3) 003-C6-008(4) 003-C6-008(3) 003-C6-008(4)
7-5/8 3.250 26.000 4.000 5.468 3.316 5.000 2.875
3 1 SETTING SLEEVE 581-55-470 581-55-470 580-70-470 580-70-470 580-75-470
7-5/8 4.000 26.125 4.000 5.468 3.316 5.250 2.875
4 3 SET SCREW 3/8-16 X 1/2" 3/8-16 X 1/2" 3/8-16 X 3/8" 3/8-16 X 3/8" 3/8-16 X 3/8"
003-C6-008 003-C6-008 003-C6-006 003-C6-006 003-C6-006 8-5/8 4.000 26.750 3.563 7.000 3.316 6.469 2.750
5 1 INNER ADAPTER 595-55-461 595-55-461 580-71-461 580-70-461 595-55-461 9-5/8 4.750 27.250 3.563 8.000 3.316 7.750 2.750
6 3 SET SCREW 1/4-20 X 3/8" 1/4-20 X 3/8" 1/4-20 X 5/8" 1/4-20 X 5/8" 5/16-18 X 3/4"
003-C4-006 003-C4-006 003-C4-010 003-C4-010 003-C5-012
7 1 INNER ADAPTER CAP 595-55-462 581-55-103 580-71-462 580-70-462 580-75-462
© 2000 WEATHERFORD This document is the confidential property of Weatherford International, Inc. and may not be reproduced
in any way, either whole or in part, or distributed without the expressed written authorization of Weatherford International, Inc.