METROLOGY & ENGINEERING SERVICES Excellence, it's Qur Promise
CERTIFICAT D’ETALONNAGE
CALIBRATION CERTIFICATE
N° D71-053/19
Délivréa: CERI
Issued to: ZI La Charguia- Rue 8600 N°82-Tunis
Tunis
Equipement étalonné
Calibrated instrament
Désignation : Dial Indicator
Designation
Constructeur: = NA
Manufacturer :
N° de série: 8842
Seriai Number :
Date d’émission : 04/12/2019
Date of issue :
Ce certificat comprend (03) pages
This certificate include (03) pages
PRESIDENT DIRECTEUR GENERAL
(CHIEF EXECUTIVE OFFICER
'SMADHI MOHAMED
La eprodhtion de ce cenit next stride queso a fre de simile hotographique tra
This crise ray not bo reece lhe tha afl ty photographic proces.
PROTIMESS sa, Lot 34 Zone Industrielle Zriba 4, 1152 - Zaghouan— Tunisie
[MF :127320SI/A/MI000 , R.C : B06214252012, Tél: +216 72 668 421, Fax: +216 72 668 431
site: www.pratimess.com, Email : protimess@protimess.comCALIBRATION CERTIFICATE N° D71.053/19
ent
05 mm
|
0,01 mm |
Température 2021 °C Date d’étalonnage : 26/11/2019
‘Temperature Date of calibration
‘Humidité 50=10 %RH Réalisé par: BM.Wajih
Humidity Operator
Liew Laboratory
Place of calibration
Mode opératoire
‘Operating procedure
L’étalonnage a été effectué par comparaison directe des indications de I'instrument soumis a I’étalonnage avec un
étalon référencé ci-dessous en points répartis sur toute l’étendue de mesure,
‘The calibration was performed by direct comparison of instrument indications under test with a standard referenced below. At
points distributed over the entire measuring range.
Référentiels utilisées
‘Used references
DCT-PR-EV-D 11; Procedure of Dimensional calibration
D&signation Marque ‘Modile
Designation | Brand model Certificate N
‘Gauge Block MITUTOYO 1600416 €190628-01
Page 2/3,
PROTIMESS sa, Lot 34 -Zone Industrielle Zriba 4, 1152 - Zaghouan ~ Tunisie
MF :127320SJ/A/M/000 , RC : BO62142S2012, Te: +216 72 668 421, Fax: +216 72 668 431
site: www.protimess.com, Email : protimess@protimess.comCALIBRATION CERTIFICATE N° D71-05:3/19
Tracabilité
L’étalonnage a été réalisé avec des étalons raccordés & la chaine (inter)nationale.
‘The calibration has been executed by instruments that are traceable to (international standards
Incertitude
Uncertainty
Les incerttudes élargies mentionnées sont celles correspondant & deux incertitudes-types. Les incertitudes sont caloulées en
tenant compte des différentes composantes d’incertitudes, étalons de référence, moyen d’étalonnage, conditions
environnement, contribution de I’instrument étalonné, répétabilité
‘The reported expanded uncertainties is determined by a coverage factor K=2 providing @ level of confidence of approximately
95%, The uncertainties are calculated taking into account the different components of uncertainties, reference standards,
calibration means, environmental conditions, contribution of the calibrated instrument, repeatability
Résultats de I’étalonnage
[Wateur dela] Valeur ive sarle | Errear | Tnoerttade Sarge
ale étalon | décamétre Expanded
ancertaingy (K=2)
(mm) (mm) (mm) (um)
0 0,00 0,00
2 2.00 0.00
3 3,00 0,00 2
4 sor oor
5 501 01
1
Fin de Certificat
7S End of Certificat
Page 3/3
PROTIMESS sa, Lot 34 ~Zone Industrielle Zriba 4, 1152 - Zaghouan— Tunisie
MF :127320Sd/A/M/000 , R.C : BO6214252012, Tél: 4216 72 668 421, Fax: +216 72 668 431
site : www.protimess.com, Email: protimess@protimess.com