Professional Documents
Culture Documents
Eurocode 1: Actions On Structures - Part 1-1: General Actions - Densities, Self-Weight, Imposed Loads For Buildings
Eurocode 1: Actions On Structures - Part 1-1: General Actions - Densities, Self-Weight, Imposed Loads For Buildings
Structural safety,
EN 1990 serviceability and
durability
Actions on
EN 1991 structures
Geotechnical
EN 1997 EN 1998 and Seismic
design
Programme of implementation
of EN 1991-1-1
• Foreword
• Section 1 General
• Section 2 Classification of Actions
• Section 3 Design Situations
• Section 4 Densities of Construction and Stored
Materials
• Section 5 Self-weight of Construction Works
• Section 6 Imposed Loads on Buildings
• Annex A (Informative) Tables for Nominal
Density of Construction Materials, and Nominal
Density and Angles of Repose for Stored
Materials
• Annex B (Informative) Vehicle Barriers and
Parapets for Car Parks
Scope of EN 1991-1-1
C 5:A reas susc eptible to large crow ds, e.g. in buildings for public
events like concert halls, sports halls inc luding stands, terraces and
access areas and railw ay platform s.
Category C
- C1 2,0 to 3,0 3,0 to 4,0
- C2 3,0 to 4,0 2,5 to 7,0 (4,0)
- C3 3,0 to 5,0 4,0 to 7,0
- C4 4,5 to 5,0 3,5 to 7,0
- C5 5,0 to 7,5 3,5 to 4,5
Category D
-D1 4,0 to 5,0 3,5 to 7,0 (4,0)
-D2 4,0 to 5,0 3,5 to 7,0
NOTE: Where a range is given in this table, the value may be set by the National annex. The
recommended values, intended for separate application, are underlined. qk is intended for the
determination of general effects and Qk for local effects. The National annex may define different
conditions of use of this Table.
Additional loading from movable partitions
2 + (n − 2)ψ0 5 A0
αn = , α A = ψ0 +
n 7 A
1 αA 1
αn UK
CEN, DE
FR (C, D) A)
n)
0,90.9 0,90.9 FI
N( A)
( n)
N1( A)
2 ( n0,8
) 0,80.8
0.8 ) FR
ČR (C, D)
A)
ČR (C, D) 0,70.7
n) 0,70.7 A)
n1) UK 1( A) ČR (A, B)
2( A0,6
) 0.6
CEN DE (C, D)
( n) 0,60.6
FR (A, B) DE (A, B)
ČR (A, B) n A [m2]
0,50.5 0,50.5
20 30 40 50 60
22 44 66 88 10
10 20 30 40 50 60
A
Factors ψi
Actions ψ0 ψ1 ψ2
40 0,75 0,96
80 0,63 0,84
120 0,59 0,80
160 0,56 0,78
240 0,54 0,76
Reduction factor αn for columns
1 1,00
2 1,00
3 0,90
4 0,85
5 0,82
6 0,80
7 0,79
8 0,78
9 0,77
10 0,76
Imposed loads on floors due to storage
Roof qk Qk
[kN/m2] [kN]
Category H qk Qk
NOTE 1 For category H qk may be selected within the range 0,0 to 1,0 kN/m2 and Qk may be
selected within the range 0,9 to 1,5 kN. Where a range is given the values may be set by the
National Annex. The recommended values are: qk = 0,4 kN/m2, Qk = 1,0kN
NOTE 2 qk may be varied by the National Annex dependent upon the roof slope
NOTE 3 qk may be assumed to act on an area A which may be set by the National Annex. The
recommended value for A is 10m2, within the range of zero to the whole area of the roof.
NOTE 4 See also 3.3.2 (1)
Category B and C1 qk
Categories C2 to C4 and D qk
Category C5 qk
Category E qk
NOTE 2 For categories C2 to C4 and D qk may be selected within the range 0,8 kN/m to -1,0 kN/m
NOTE 3 For category C5, qk may be selected within the range 3,0 kN/m to 5,0 kN/m
NOTE 4 For category E qk may be selected within the range 0,8 kN/m to 2,0 kN/m. For areas of
category E the horizontal loads depend on the occupancy. Therefore the value of qk is defined as a
minimum value and should be checked for the specific occupancy.
NOTE 5 Where a range of values is given in Notes 1, 2, 3 and 4, the value may be set by the National
Annex. The recommended value is underlined.
NOTE 6 The National Annex may prescribe additional point loads Qk and/or hard or soft body impact
specification for analytical or experimental verification.
Annex A (informative) : Nominal
densities and angles of repose
For vehicles < 2500 kg: m = 1500 kg, v = 4,5 m/s, δc = 100 mm
Backgound Documents
and other supporting material