This document specifies the requirements for an uninterruptible power supply (UPS) system. The UPS must support an input voltage range of 340-470V AC, output voltage of 380/400/415V 3-phase, and frequency regulation of 50Hz +/-0.5%. It must have an input power factor above 0.99, total harmonic distortion below 5%, and efficiency above 96%. The UPS enclosure must be rated IP21 and include static and manual bypass facilities. It must also support hot-swappable battery modules with 4-8 hour recharge times.
This document specifies the requirements for an uninterruptible power supply (UPS) system. The UPS must support an input voltage range of 340-470V AC, output voltage of 380/400/415V 3-phase, and frequency regulation of 50Hz +/-0.5%. It must have an input power factor above 0.99, total harmonic distortion below 5%, and efficiency above 96%. The UPS enclosure must be rated IP21 and include static and manual bypass facilities. It must also support hot-swappable battery modules with 4-8 hour recharge times.
This document specifies the requirements for an uninterruptible power supply (UPS) system. The UPS must support an input voltage range of 340-470V AC, output voltage of 380/400/415V 3-phase, and frequency regulation of 50Hz +/-0.5%. It must have an input power factor above 0.99, total harmonic distortion below 5%, and efficiency above 96%. The UPS enclosure must be rated IP21 and include static and manual bypass facilities. It must also support hot-swappable battery modules with 4-8 hour recharge times.
In put Voltage Range 340 V to AC to 470 V AC 3 Phase Input frequency range 50 +/-10% Hz Input power factor at full output load leading to >/=0.99 unity with active power factor correction (APFC) (from 25% load to 100% load) Distortion (current) < / = 3% UPS shall have DG set compatibility Yes Output AC Three Phase Out put voltage 380/400/415, 3 phase, 4 wire Voltage regulation (Steady state) at No load to +/-1% full load, 0.6 lag to Unity PF, During entire back up time, Complete input voltage range Output powr factor >/=0.99 Frequency 50 Hz +/-0.5 % Hz Minimum thickness (in mm) of Rack Enclosure 1.2 for Modular UPS duly powder coated UPS shall be free from workmanship defects, Yes sharp edges, nicks, scratches,burst, etc. All fasteners shall be fixed properly. The equipment shall be complete with all parts and all parts shall be functional UPS enclosure's degree of protection as per Yes IS:13947 (Part 1)/1993 latest IP21 Standard quality Out put terminals shall be provided for output connection UPS shall have static and manual by pass facility Yes UPS shall be supplied with required rated power 5 Meters cable (Copper) Total Harmonic Distrotion (THD) for 100% < 2% linear load Total Harmonic Distrotion (THD) for 100% non- < 5% linear load Over all efficiency on rated full load of 0.8 PF >/=96% (min.) AC output Inverter efficiency on rated full load of 0.8 PF >/=96% (min.) AC output Crest factor on full non-linear load Not less than 3:1 UPS shall withstand Over load capacity - 125% for 10 Minutes (Minimum) (Output with mains AC-AC) UPS shall withstand Over load capacity - 150% for 60 seconds (Minimum) (Output with mains AC-AC) UPS shall withstand Over load capacity - 125% for 2 Minutes (Minimum) (Output in battery run DC-AC) UPS shall withstand Over load capacity - 150% for 30 seconds (Minimum) (Output in battery run DC-AC) Load power factor 0.8 lagging to unity Yes Transient response time (for 100% load change, <20 milli seconds output must remain within +/-1% and recovery) Short circuit protection Yes Over load protection Yes Over temperature protection Yes In put low/high voltage control Yes DC low/high voltage trip Yes Back feed protection for both, mains and bypass Yes input Battery shall conforming to Yes JISC:8702(Pt.I,II&III) latest or equivalent BIS standard Battery type SMF VRLA, Modular Hot swappable Battery modules Battery recharge time (after complete discharge to 4 to 8 hours 90% charge) and charge rating: Battery recharge time to 90% charge after 100% DoD Battery charger (One in each power module) Yes should be capable to charge battery on C10 rating Battery cutoff voltage during back up Not less 10.5 V than Batteries shall supply with With Modular cabinet having hot swappable battery Modular UPS shall supply with DC Cable from Yes UPS to battery and batteries to UPS , Battery interlink cables, battery breaker Warranty for Modular UPS (on site 5 comprehensive warranty) (in years) Warranty for battery (replacement warranty) (in 5 years) After sales and complaint service within 48 hours Yes PAN India service support on 24 x 7 basis AMC support available after 3 year warranty Yes Quarterly preventive maintenance Yes Manufacturer shall provide and support for Yes installation, commissioning, spares, technical support all over India Availability of spares in close proximity (Spares Yes should be easily available close to the site)
Real-Time Monitoring and Capture of Power System Transients D. F. Peelo, F. Rahmatian, M. Nagpal, and D. SYDOR Consultant, Quanta Technology, and BC Hydro Canada