Professional Documents
Culture Documents
SUPPLEMENT
153003
TEMPERATURE REGULATOR
INSTRUCTIONS
153003
Digital Temperature Controllers
E5CN/E5CN-U
Features
Improved Functions for a Wider Range of Application
Control Analog Values, such as Pressures, Flowrates, Voltage Outputs (to Drive SSRs) for Both Heating and
and Levels Cooling Control. Can Be Used for Alarms to Provide
The new E5CN Series now also includes models that accept analog Three Alarm Outputs.
inputs, enabling control applications other than for temperature, Voltage outputs can be used for both heating and cooling for Models
including pressure, flowrate, level, humidity, and weight control. with Two Control Outputs. Also, control output 2 can be set for use as
Note: E5CN-@L (Models with Analog Inputs) an alarm output, to enable using up to three alarm outputs.
Note: E5CN-@Q (Option Board)
Faster Sampling at 250 ms
The previous sampling time of 500 ms has been reduced by half to Three-phase Heater Burnout Detection
250 ms. This enables the new E5CN to handle application requiring With Models with Three-phase Heater Burnout and SSR Failure
even greater response speed and accuracy. Detection, two current transformers can be connected to detect both
heater burnout and SSR failure at the same time, reducing costs
Easy Connector to a Recorder because a separate heater burnout alarm device is not required.
A transfer output now makes it easy to connect to a recorder or PLC SSR failure detection can be used even with Models with Single-
Analog I/O Unit. phase Heater Burnout Alarms.
Note: E5CN-C@ (Models with Current Outputs) Note: E5CN-@HH@ (Option Board)
1. Output type
R: Relay
Q: Voltage (for driving SSR)
C: Current
Y: Long-life relay output (available soon)
2. Number of alarms
Blank: No alarm
2: Two alarms
3. Option Unit
M: Option Unit can be mounted
4. Input type
T: Thermocouple/platinum resistance thermometer (multi-input)
L: Analog input
This data sheet is provided as a guideline for selecting products. Be sure to refer to the following user manuals for application precautions
and other information required for operation before attempting to use the product.
E5CN/E5CN-U Temperature Controller User's Manual (Cat. No. H129)
E5CN Temperature Controller Communications User's Manual (Cat. No. H130)
■ Option Units
The E5CN provides optional functionality when one of the following Option Units is mounted.
Functions Model
Communications Heater burnout/SSR failure detection E53-CNH03N
Communications E53-CN03N
Heater burnout/SSR failure detection Event inputs E53-CNHBN
Event inputs E53-CNBN
Communications 3-phase heater burnout/SSR failure detection E53-CNHH03N
Communications Control output 2 (voltage output) E53-CNQ03N
Heater burnout/SSR failure detection Control output 2 (voltage output) E53-CNQHN
B 11 11 B 11 11 B 11 B 11 + 11 Voltage
output
RS-485 RS-485 RS-485 RS-485 Control
output 2 12 VDC,
A 12
EV1
12 A 12
EV1
12 A 12 A 12 − 12 21 mA
Do not Do not Do not Do not
use. 13 EV2
13 use. 13 EV2
13 13 use. 13 use. 13
CT2
Do not Do not +
14 14 use. 14 use. 14 14 14 14
CT1 CT1 CT1
Control CT1
Do not Do not output 2
15 15 use. 15 use. 15 15 − 15 15
Note: Use this Adapter when the panel has been previously prepared
Current Transformers (CTs) for the E5B@.
Model E54-CT1 E54-CT3
Hole diameter 5.8 dia. 12.0 dia.
Sockets
(for Models with Plug-in Connectors)
Model P2CF-11 P2CF-11-E P3GA-11 Y92A-48G
Type Front- Front- Back- Terminal
connecting connecting connecting Cover for
Socket Socket with socket Finger
Finger Protection
Protection
1800
1800
Usable in
1700 1700 the following
1700 ranges by
1600 scaling:
1500 -1999 to
1400 9999 or
1300 1300 -199.9 to
1300
999.9
1200
1100
Temperature range (°C)
1000
850 850 850
900
800
700
600
600
500.0 500.0 500.0
500
400.0 400 400.0 400 400.0
400
260
300
120 165
200
100.0 100.0 90
100
100
0
0.0 0.0 0 0 0 0 0 0 0
-100.0
- 20.0 -100 -20.0 -100
-200.0
-200 -199.9 -199.9 -200 -200 -199.9 - 200 -199.9 - 200
Setting 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23
number
The applicable standards for the input types U: Cu-CuNi, DIN 43710-1985 Shaded settings are the default settings.
are as follows:
Pt100: IEC 751
K, J, T, E, N, R, S, B: IEC584-1
L: Fe-CuNi, DIN 43710-1985
Insulation resistance
max. (10 W max.)
20 MW min. (at 500 VDC)
■ Current Transformer
Dielectric strength 2,000 VAC, 50 or 60 Hz for 1 min (between
terminals with different charge)
(Sold Separately)
Vibration Malfunction 10 to 55 Hz, 20 m/s2 for 10 min each in X, Y,
resistance and Z directions Ratings
Destruction 10 to 55 Hz, 0.75-mm single amplitude for
2 hrs each in X, Y, and Z directions Dielectric 1,000 VAC for 1 min
strength
Shock Malfunction 100 m/s2 min., 3 times each in X, Y, and Z
resistance Vibration 50 Hz, 98 m/s2
directions resistance
Destruction 300 m/s2 min., 3 times each in X, Y, and Z Weight E54-CT1: Approx. 11.5 g, E54-CT3: Approx. 50 g
directions
Accessories Armatures (2)
Weight E5CN Controller: Approx. 150 g, Mounting (E54-CT3 only) Plugs (2)
Bracket: Approx. 10 g
E5CN-U Controller: Approx. 110 g, Mounting
Bracket: Approx. 10 g
Degree of E5CN Front panel: NEMA4X for indoor use
protection (equivalent to IP66)
Rear case: IP20, Terminal section: IP00
E5CN-U Front panel: Equivalent to IP50, rear case:
IP20, terminals: IP00
Memory protection Non-volatile memory (number of writes:
1,000,000 operations)
+ + Alarm Outputs
1 1 1
4 to 20 mA DC/ 12 VDC
Control output 1 0 to 20 mA DC 21 mA 1 11 6 6
2 2 2
− −
2 12 7 7
A
+ 3 13 8 8
mA −
Analog input − B
4 14 9 Alarm 2 Alarm 1/
V Input power supply Heater burnout alarm/
+ B Input error output (See note.)
+ 5 15 10
Note: Output when an input error output is
Pt TC
enabled in the Advance Function Setting
Platinum Infrared
resistance temperature Level. If an input error output is enabled,
thermometer sensor the a1-1 operation indication on the front
The input power supply depends on the power panel will not light and s.err will be
supply specification of the Controller and is displayed on the No. 1 display.
either 100 to 240 VAC or 24 VAC/DC (no Voltage output
polarity). 12 VDC, 21 mA
B B +
11 11 11 11
RS-485 RS-485 Control output 2
12 12 12 12
A A −
Event input 1 Do not Do not
13 13 connect. 13 connect. 13
Event input 2
+
14 CT2 14 14 14
CT1 CT1 Control output 2 CT1
15 15 15 15
−
Heater burnout/ Heater burnout/ Voltage output Heater burnout/
SSR failure SSR failure 12 VDC, 21 mA SSR failure
detection input detection input detection input
Event input/ Communications/ Communications/ Voltage output/
Heater burnout / Heater burnout/ voltage output Heater burnout/
SSR failure SSR failure specification SSR failure
detection detection (2-CT input)
detection
Terminals 11 to 15 do not exist on models without an Option Unit (heater burnout detection, control output 2, event inputs, or communications).
Terminal applications depend on the model of the Option Unit.
E5CN-U
Voltage Output Relay Output
− One Alarm Output Two Alarm Outputs
5
DC12V
6
Control output 1 4 5 7 7
21mA Alarm 1/
+ Input error output Alarm 1/
4 8 8 Input error output
(See note.)
A Do not connect. Alarm 2/
3 9 9
Control output 2
− B −
2 10
Analog input B Note: Output when an input error output is
1 11 Input power supply
+ + enabled in the Advance Function
Pt TC Setting Level. If an input error
0 to 50 mV input only Platinum Infrared temperature sensor output is enabled, the al-1
resistance
thermometer operation indication on the front
panel will not light and s.err will be
The input power supply depends on the power supply specification of the displayed on the No. 1 display.
Controller and is either 100 to 240 VAC or 24 VAC/DC (no polarity).
Order the P2CF-11 or P3GA-11 Socket separately. (See page 14.)
Temperature unit
No.1 display
Operation indicators
No. 2 display
Up Key
Level Key
Dimensions
■ Standard Models
91
6
48 × 48 78
45 +0.6
0
E5CN-U
Plug-in Models Panel Cutout
Mounted Separately Group Mounted
(48 × number of units −2.5) +1.0
0
6 14.2
48 × 48 70.5
45 +0.6
0
60 min.
58 44.8 × 44.8 • Recommended panel thickness is 1 to
5 mm.
• Group mounting is not possible in the
45 +0.6
0
vertical direction. (Maintain the
specified mounting space between
Controllers.)
Mounting Adapter • When two or more Controllers are
(Accessory) 45 +0.6 mounted, make sure that the
0
surrounding temperature does not
exceed the allowable operating
temperature specified in the
specifications.
Terminal Cover
48
E53-COV10
48.8
22
Note: The suffix “500” is added to the model number of each
Controller provided with a E53-COV10 Terminal Cover.
9.1
E54-CT1 21
2.8
15
5.8 dia.
7.5
25 3
10.5
40
10
30
40 × 40
18
• Plug
Two, M3 (depth: 4)
Approx. 6 dia.
15
30 (22)
Y92F-45
Fixture (Accessory)
4.7 76
69.6 to 77.6
72 × 72
67 × 67 87
48 × 48
2.2 4.7
77.3 (to back of E5CN)
Front-connecting Socket
Eleven, M3.5 × 7.5 3 4.5 Terminal Layout/Internal Connections
P2CF-11 sems screws 7.8 (Top View)
8 7 6 5 Mounting Holes
4
Two, 4.5 dia mounting holes
70 max. 35.4
Two, 40±0.2
4.5-dia. 9 3
holes
10 11 1 2 Note: Can also be mounted to a DIN track.
4 50 max.
31.2 max.
Back-connecting Socket
P3GA-11
45
4.5 16.3 6.2
6
8.7
Note: 1. Using any other sockets will adversely affect accuracy. Use only the specified sockets.
2. A Protective Cover for finger protection (Y92A-48G) is also available.
Power ON
Starting in manual mode Starting in automatic mode
Press the Level
Key for at least 1 s.
Press the
Operation Level Adjustment Level
Level + Mode Keys;
Press the display will flash.
C Press the
a-m Level Key
less than 1 s. Level + Mode C
Keys.
Press the Level Key for at least 1 s
25
Press the Level Key for at least 1 s; 100
C
for at least 1 s;
display will flash.
Press the
Level Key for 25 display will flash.
Press the Level +
Manual Press the Level Key
at least 1 s. (See 100 Press the Level Key for
Mode
(See for at least 3 s while at least 3 s. Mode Keys for at least
note 3.) a-m is displayed. note 1.) Control stops .
3 s. (See note 4.)
Manual Communications
Initial Setting Level Setting Level
Control Level Protect Level
Press the Level Key
for less than 1 s.
Advanced Function
Setting Level
Control in progress
Input password.
Set value 1201 Control stopped
Set either of these parameters. Set either of these parameters. Set either of these parameters.
Adjustment level
25 Process value al-1 Alarm value 1
C C
l.adj display
p Proportional band Added when PV
C
0
Displayed only once when display is added.
entering adjustment level. 8.0 a a
a
a
25 Process value/ al1h Upper-limit
C C
a a
0.0 monitor 0
hys Hysteresis (heating)
C
lcr2 Leakage current value a a
0.0 2 monitor
lcr1 Leakage current al3h Upper-limit
C
1.0
Hysteresis settings
a a
0.0 value 1 monitor alarm value 3
0
hb1 Heater burnout 1 chys Hysteresis (cooling)
C
a a
0 off Communications
a
SP used by multi-SP
a Protect Level Setting Level
sp-2 SP 2
C
ol-h MV upper limit The time taken to move to the protect level can
be adjusted by changing the "Move to protect
Displayed only for models with communications.
Changes are effective after cycling power or after
0 105.0 level time" setting. a software reset.
a a
Move to protect level
sp-3 SP 3
C
ol-l MV lower limit pmoV Displayed only when a password psel
Protocol setting
0 -5.0 Switches between
0 is set. Restricts moving to protect cwf CompoWay/F
a level.
a a a (SYSWAY) and Modbus.
ins Temperature input shift
C
Operation/adjustment
0.0
1-point shift
protection u-no Communications
a
oapt Restricts displaying and modifying
1 Unit No.
0 menus in operation, adjustment, a
insh Upper-limit Set either of these parameters. CompoWay/F
C
and manual control levels.
a
temperature input
0.0
2-point shift Initial Setting/ bps Baud rate (SYSWAY) only
9.6
C
a icpt This protect level restricts movement
Communications Protection
a
insl Lower-limit 1 to the initial setting, communications
0.0 temperature input a setting, and advanced function
setting levels.
len Data bits
7
a
wtpt Setting change protection
Protects changes to setups by
a
off
a
operating the front panel keys. sbit Stop bits
2
a
pmsk Parameter mask enable
Displayed only when a
on parameter mask is set. prty Communications
a eVen parity
a
prlp Password to move to
0
protect level sdwt Send delay
Password setting 20
a a
a a a
1300
a
Limit the set point.
spru SP ramp time unit a3lt Alarm 3 latch hsh SSR failure
off 0.1 hysteresis
sl-l SP lower limit
C
m
a a a
-200
a
rest Standby sequence prlt Move to protect level time lba LBA detection time
cntl PID ON/OFF a reset method 3 0
onof a a a
alt1 Alarm 1 type hbu Heater burnout a2on Alarm 2 ON delay csel Display text switch
2 on detection 0 on
a a a a
alt2 Alarm 2 type hbl Heater burnout latch a3on Alarm 3 ON delay t-u Soak time unit
2 off 0 m
a a a
a
6 mm
The following items do not change in comparison to the previous E5CN models: Panel cutout, Internal panel
dimensions for panel mounting, wiring screw sizes, wiring terminal arrangement, and parameter setting
methods.
■ Improved Functions
The previous and new models can be easily differentiated by looking at the front panel. The OMRON logo is in a different position.
Item Previous models (OMRON logo: lower left) Improved models (OMRON logo: upper left)
Front panel
ALM1
ALM2
HB
OUT1 STOP
OUT2 CMW
Basically, the Controllers are upwardly compatible. The terminal arrangement, terminal sizes, and depth for panel mounting have not been
changed. Changes are listed in the following tables. For details, refer to the E5CN/E5CN-U Temperature Controller User's Manual (Cat. No. H129)
and to the E5CN Temperature Controller Communications User's Manual (Cat. No. H130).
Characteristics
Item Previous models Improved models
Sampling period 500 ms 250 ms
Communications Specifications
Item Previous models Improved models
Communications CompoWay/F (SYSWAY) CompoWay/F (SYSWAY), Modbus
protocols
Baud rate 1200, 2400, 4800, 9600, 19200 bps 1200, 2400, 4800, 9600, 19200, 38400 bps
The degree of protection is as shown below. Sections without any Tool insertion hole
specification on their degree of protection or those with IP@0 are not Flat-blade screwdriver
(Unit: mm)
waterproof.
Front panel: NEMA4X for indoor use (equivalent to IP66) (1) ALM1
ALM3
20 min.
HA
CMW
MANU
SV
Operating Precautions
0.4
2.0
(2)
1. It takes approximately two seconds for the outputs to turn ON (1) E5 C
N
from after the power supply is turned ON. Due consideration must
be given to this time when incorporating Temperature Controllers 1. Insert the tool into the slots (one on the top and one on the
in a sequence circuit. bottom) and release the hooks.
2. When using self-tuning, turn ON power for the load (e.g., heater) 2. Insert the tool into the gap between the front panel and rear case
at the same time as or before supplying power to the Temperature and pull out the front panel slightly. Hold both sides of the front
Controller. If power is turned ON for the Temperature Controller panel and draw out the Controller towards you. Do not apply
before turning ON power for the load, self-tuning will not be unnecessary force.
performed properly and optimum control will not be achieved. 3. Before inserting the Controller, confirm that the sealing rubber is
3. When starting operation after the Temperature Controller has in place. Insert the Controller into the rear case until you hear a
warmed up, turn OFF the power and then turn it ON again at the click. Press on the hooks on the top and bottom of the rear case
same time as turning ON power for the load. (Instead of turning to be sure that the hooks are securely locked in place.Be sure
the Temperature Controller OFF and ON again, switching from that electronic parts do not come in contact with the case.
STOP mode to RUN mode can also be used.) Avoid using the
Controller in places near a radio, television set, or wireless
installing.
4. These devices can cause radio disturbances which adversely
affect the performance of the Controller.
7.2 mm min.
7.2 mm min.
LIMITATIONS OF LIABILITY
OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS,
OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON
CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE
PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED,
INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of
products in the customer's application or use of the products.
Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will
be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON
PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR
SYSTEM.
Disclaimers
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a
warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application
requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with
your OMRON representative at any time to confirm actual specifications of purchased product.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
Cat. No. H128-E1-01 In the interest of product improvement, specifications are subject to change without notice.
OMRON Corporation
Industrial Automation Company
24