Professional Documents
Culture Documents
2
• Do not use the appliance on (or • Do not operate appliance with
close to) a hot gas or electric a damaged cord or plug, or
burner, or where it could touch after appliance malfunctions, or
a heated oven or surface. if dropped or damaged in any
• Do not allow the cord to hang way. Stop use immediately and
over the edge of a countertop, contact Breville by phone or
or to become knotted. email for replacement or repair.
• To avoid electric shock, do not • Do not use blender while
immerse the cord, plug OVERLOAD PROTECTION is
or motor base in water (or other flashing on the LCD.
liquids). If your blender stops operating
• Installation of a residual and the "OVERLOAD
current device (a standard PROTECTION" is flashing,
safety switch on your wall unplug the blender and wait for
socket) is recommended to 30 minutes until the motor has
provide additional safety cooled off. Once cooled, you
protection when using will be able to use the blender
appliances. It is advisable as usual again.
that a safety switch (with
a rated residual operating
current not more than 30mA)
be installed in the electrical
circuit supplying the appliance.
Contact your electrician for
further professional advice.
• In order to avoid the possible • All maintenance (other than
hazard of the blender starting cleaning) is to be done by
by itself due to inadvertent an authorised Breville
resetting of the overload Service Centre.
protector on the motor, do not • Authorised Breville Service
attach an external switching Centres can be found on our
device (such as a timer) or website www.Breville.com.au
connect the blender to a circuit Alternatively, you can contact
that can regularly switch the the Breville Customer Care
blender on and off. Centre by phone on
1300 273 845 or email
AskUs@breville.com.au
3
SAFEGUARDS • Do not leave the blender
unattended when in use.
FOR YOUR • Keep hands, fingers, hair
BLENDER and clothing away from the
blender during use. Always
• Wash the blender jug with turn blender off and unplug at
warm soapy water before the wall before reaching inside.
first use. Avoid touching moving parts.
• Use only the blender jug • Be careful when handling the
and lid that is supplied with blender jug as the blades are
this blender. The use of very sharp. Be careful when
attachments or accessories not emptying the jug and during
manufactured or specified by cleaning. Mishandling of the
Breville may cause the risk of blades may cause injury.
fire, electrical shock, or injury. • Do not remove the jug from
• Always ensure the blender is the motor base while blender
assembled properly before is in use.
using. Lid must be firmly • The blender is intended for
secured to the jug before food or drinks preparation.
operation to ensure internal Do not use for anything
contents do not escape, spray other than food or drinks.
or overflow. Do not operate without any
• Under heavy load the blender ingredients in the blender jug.
should not be operated for • Never attempt to operate
more than 1 minute. Heavy with damaged blades, or with
load for this blender was utensils, or any foreign objects
defined defined as per the inside the blender jug.
appliance safety standard
specified load (6 ice cubes • To reduce the risk of severe
(120g), 3 frozen bananas injury to persons or damage
halves (250g) , 180g frozen to the blender, keep hands and
raspberries, 500ml milk, utensils out of the jug while
3 scoops vanilla ice cream blending.
(140g). Any load equivalent
to this or heavier should not
be operated for more than 1
minute.
4
• Never blend hot liquids. • Appliances can be used by
Allow ingredients and liquids persons with reduced physical,
to drop to room temperature sensory or mental capabilities
before putting into the jug or lack of experience and
for blending. knowledge if they have
• Do not put the blender jug in been given supervision or
extremes of heat or cold, for instruction concerning use of
example placing a cold jug into the appliance in a safe way and
hot water, or vice versa. if they understand the hazards
• Before moving the blender, involved.
cleaning or putting it away for • This appliance shall not be
storage, always turn blender off used by children. Keep the
and unplug at the wall. appliance and its cord out of
• Always disconnect the reach of children.
appliance from the supply if it • Cleaning and user
is left unattended and before maintenance shall not be
assembling, disassembling made by children without
or cleaning. supervision.
• Always disconnect the
IMPORTANT appliance from the supply if it
is left unattended and before
SAFEGUARDS assembling, disassembling or
FOR ALL cleaning.
• Children should be supervised
ELECTRICAL to ensure that they do not play
APPLIANCES with the appliance.
• It is recommended to regularly
• Fully unwind the cord before inspect the appliance. Do not
use. use the appliance if the power
• To protect against electric supply cord, plug or appliance
shock, do not immerse the cord, becomes damaged in any way.
plug or motor base in water or Return the entire appliance to
any other liquid. the nearest authorised Breville
• Do not allow the cord to hang Service Centre for examination
over the edge of a table or and/or repair.
bench, touch hot surfaces or
become knotted.
5
• Any maintenance other than BREVILLE ASSIST™ PLUG
cleaning should be performed Your Breville appliance comes
at an authorised Breville with a unique Breville Assist™
Service Centre. Plug, conveniently designed
• This appliance is for household with a finger hole to easy
use only. Do not use in moving removal from the wall outlet.
vehicles or boats. Do not use
outdoors. Do not use this
appliance for anything other
than its intended use. Misuse
may cause injury.
• The installation of a residual
current device (safety switch)
is recommended to provide
additional safety protection
when using electrical
appliances. It is advisable that
a safety switch with a rated
residual operating current
not exceeding 30mA be
installed in the electrical circuit
supplying the appliance.
See your electrician for
professional advice.
F
G
H
7
Functions
8
MANUAL SPEED SELECTION • The speed can be changed at any time during
the blending process. Each time a new speed
ON | OFF is selected its button will illuminate and the
previous speed button illumination will go
The ON | OFF button powers the unit into
out. The number of seconds on the LCD
READY mode.
timer screen will continue to count upwards
ELECTRONIC SPEED CONTROL to 120 seconds unless interrupted.
10
Hints & Tips Do's
• If the volume (while blending) is below the
maximum line, the inner measuring cap can 99
Use a combination of the blending speeds
and AUTO PULSE/ICE CRUSH function to
be removed and oils/liquids can be added
suit the foods being processed.
while blender is in use.
• Run the blender only for the appropriate 99
Use the SMOOTHIE function to blend
fruits, ice cream and yogurts into thick
amount of time required – do not over
smoothies, whips and milkshakes.
blend ingredients.
• Use the AUTO PULSE/ICE CRUSH button 99
Use the AUTO PULSE/ICE CRUSH
function for foods that only require short
when food is too thick or coarse to circulate
bursts of power, such as chopping nuts and
within the blender jug.
crushing ice.
• Do not exceed the maximum mark when
adding foods and liquids into the blender. 99
When blending drinks with ice cubes or
frozen fruit, use the AUTO PULSE/
• Ingredients may stick to the sides of the ICE CRUSH function.
blender jug. To push food back onto the
blades, turn the blender off and unplug at the 99
Thicker mixtures puree more efficiently if
the jug is ¼ to ½ full.
wall. Use a plastic spatula to scrape down the
sides of the jug, and continue blending.
• If any moisture or liquid appears on top of
the motor base during blending, turn the Don’ts
blender off and unplug at the wall. Remove
the blender jug, and wipe motor base
immediately with a dry cloth or paper towel. 88
Do not use metal utensils, as they may
damage the blades or blender jug.
• When the blender has been running for
120 seconds, it will automatically turn off. 88Do not blend a heavy mixture for more
This is a safety feature to protect the motor. than 10 seconds. For normal blending tasks,
do not blend longer than 1 minute at a time.
• A speed can be selected at any time, even If you need to blend longer, turn off the
while the blender is running. blender and stir ingredients before starting
Press the new speed, and the blender will again. This rest will help protect the motor
change operation immediately. The motor from wear and tear.
will still automatically turn off at
120 seconds total time running time. 88The blender will not knead dough, or
mash potatoes.
• The maximum amount of ice cubes that
the blender can process is 250g (approx. 88When blending warm ingredients, do not
1 standard ice tray). put more than 2 cups at a time in. Once
blending has started, you can add another
cup slowly by removing the inner lid and
pouring through the hole.
88Do not blend hot or boiling ingredients.
Allow food to cool down to a warm state
before placing in the blender. This is to
safeguard against sudden bursts of steam
that are caused by blending hot ingredients,
and it also protects the jug from possible
damage.
11
Blending Chart
Bread or Cut into 2cm pieces, 100g CHOP | Speed 2 10–30 sec
biscuit crumbs break up biscuits.
Mayonnaise Mix the egg yolk and 125g MIX | Speed 1 60 sec
vinegar, then add oil slowly
through the lid
Whipped cream Add sugar or vanilla 300ml MIX | Speed 1 10–20 sec
if desired. and AUTO PULSE/ 10–20 sec
ICE CRUSH
Herbs and spices Roughly chopped 1 cup CHOP | Speed 2 20–30 sec
Fresh fruit Chopped or whole berries 250g BLEND | Speed 3 20–30 sec
12
Troubleshooting
Food is chopped too fine • Try blending for shorter period of time. Use the AUTO PULSE/ ICE CRUSH
or is watery function for better control.
Food sticks to blade • The mixture may be too thick. Try adding more liquid and/or using a slower
and jug speed for blending.
Blender overloaded • This blender has overload protection to prevent damage to the motor.
(all lights flashing) OVERLOAD PROTECTION will flash on the LCD. Unplug and allow the
blender to cool down for 30 minutes. Once cooled, you will be able to use the
blender as usual again.
• We recommend blending in smaller batches, or cutting ingredients into
smaller batches.
13
Care & Cleaning
Cleaning agents
Do not use abrasive scouring pads or cleaners
on either the motor base or the jug, as they may
scratch the surface. Use only warm soapy water
with a soft cloth.
14
15
Breville Customer Service Centre
Australian Customers New Zealand Customers
Mail: Locked Bag 2000 Mail: Private Bag 94411
Botany NSW 1455 Botany Manukau 2163
AUSTRALIA Auckland NEW ZEALAND
Phone: 1300 139 798 Phone: 0800 273 845
Fax: (02) 9700 1342 Fax: 0800 288 513
Email: Customer Service: Email: Customer Service:
askus@breville.com.au askus@breville.co.nz
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2019.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.