Professional Documents
Culture Documents
15552
Standards-based cylinders DNC, ISO 15552
Key features
At a glance
• Standards-based cylinders to • The modern, consistent design • An extensive range of accessories
ISO 15552 (corresponds to the saves up to 11% more space com- enables the cylinder to be installed
withdrawn standards ISO 6431, pared to ordinary standards-based virtually anywhere
DIN ISO 6431, VDMA 24562, cylinders, providing a significantly • The widest range of variants on the
NF E 49 003.1 and UNI 10290) more compact system structure market offers the ideal cylinder DNC
for any application
Tandem cylinder
DNCT
• Series connection of 2 cylinders
with the same piston diameter and
stroke
• Twice the thrust and return force
compared to a conventional cylinder
Key features
Variants from the modular product system
Symbol Key features Description
S2 Through piston rod The piston rod can be used for attachment at both ends of the cylinder
S10 Constant motion (slow speed) at low piston Suitable for slow stroke movements at a constant, stick-slip-free speed over the full stroke
speeds of the cylinder.
Seal contains silicone grease (not free of paint-wetting impairment substances)
S11 Low friction The special seals considerably reduce system friction. This results in a considerably lower
response pressure.
Seal contains silicone grease (not free of paint-wetting impairment substances)
S20 Through, hollow piston rod The piston rod can be used for attachment at both ends of the cylinder. The piston rod is
hollow inside. This means it can be used to carry vacuum or compressed air
K10 Smooth anodised aluminium piston rod Ideal for use in welding environments:
• Protection against welding spatter
• Small working loads
• Harder surface compared to steel
• Long service life
KP With clamping unit Integrated clamping unit on the piston rod
EL With end-position locking Positive locking in the end position as a drop guard. If there is a drop in pressure, the
cylinder is secured in its end position to prevent it from dropping
Q Square piston rod Protection against rotation. For correctly oriented feeding
R3 High corrosion protection All external cylinder surfaces comply with corrosion resistance class 3 to Festo standard
940070. The piston rod is made from corrosion- and acid-resistant steel
R8 Dust protection with wiper seal The cylinder has a hard-chrome-plated piston rod and a hard wiper seal, which protects
against dry, dusty media
Extended male
Custom thread
Female piston
rod thread
[mm] [mm] A Q S2/S20 K2 K3 K5
Double- Basic version
acting DNC 32, 40, 20, 25, 30, 40, 10 ... 2000
50, 63, 50, 60, 70, 80,
80, 100, 100, 125, 150,
160, 200, 250,
h h h h h h
125
300, 320, 400,
500
Cylinder/valve combination
Heat-resistant seals max.
Dust protection
Low friction
120°C
K7 K8 rod
K10 S6 S10 S11 R3 R8 V1 ... V6
Basic version
DNC 9
h h h h h h h h –
h h – – – – – – h
DNCKE 2
– – – – – – – – –
h h h – h h – h h
– – – h – – – – –
Peripherals overview
2
5 9
3
8
4 7
6
6
10
9 11
12 14
11
13
12 5
15
16
26
17 19
18 20 25
21
22
24
2
3
4
Peripherals overview
Mounting components and accessories
Description DNC a Page/
Basic KP EL V1 ... V6 Internet
version
[9] Swivel flange With spherical bearing for end caps 57
SNCS/CRSNCS/SNCS-...-R3
h1) h1) h h1)
[10] Clevis foot – 59
LBG/LBG-...-R3
h1) h h h1)
[11] Swivel flange For end caps 58
SNCL
h1) h1) h h1)
[12] Swivel flange For end caps 56
SNCB/SNCB-...-R3
h1) h1) h h1)
[13] Clevis foot – 59
LNG/CRLNG
h1) h1) h h1)
[14] Clevis foot With spherical bearing 59
LSN
h1) h1) h h1)
[15] Trunnion flange kit For mounting anywhere along the cylinder profile barrel 53
DAMT
h h h h
[16] Rod eye With spherical bearing 60
SGS/CRSGS
h h h h
[17] Right-angle clevis foot – 59
LQG
h h h h
[18] Rod clevis With male thread 60
SGA
h h h h
[19] Coupling piece To compensate for radial deviations 60
KSG
h h h h
Coupling piece For cylinders with a non-rotating piston rod to compensate for 60
KSZ radial deviations
h h h h
[20] Rod clevis Permits a swivelling movement of the cylinder in one plane 60
SG/CRSG
h h h h
[21] Self-aligning rod coupler To compensate for radial and angular deviations 60
FK/CRFK
h h h h
[22] Adapter For mounting a suction cup on a hollow piston rod 60
h – – h
AD
[23] Guide unit For protecting standards-based cylinders against rotation at 65
h h – –
FENG high torques
[24] Mounting kit For attaching proximity switch SMT-8 to cylinders in h 65
SMB-8-FENG combination with guide unit FENG h2) h –
from @ 50
[25] Slot cover For protecting the sensor cables and the sensor slots from 66
ABP-5-S contamination
h h h h
[26] Proximity switch Can be integrated in the cylinder profile barrel 66
SME/SMT-8
h h h h
[27] One-way flow control valve For regulating speed 67
GRLA
h h h h
[28] Push-in fitting For connecting tubing with standard O.D. qs
QS
h h h h
[29] Bellows kit • Protects the cylinder (piston rod, seal and bearings) 61
DADB against a wide range of media and thus prevents
premature wear h – h h
• The kit can only be used in combination with an extended
piston rod (K8)
Type codes
001 Series 010 Custom thread
DNC Standards-based cylinder, double-acting, based on ISO 15552 Standard piston rod thread
“M10”K5 M10
002 Piston diameter “M12”K5 M12
32 32 “M16”K5 M16
40 40 “M20”K5 M20
50 50 “M27”K5 M27
63 63
80 80 011 Special spanner flats
100 100 K7 Piston rod with external hexagon
125 125
012 Piston rod extension
003 Stroke None
... 2 ... 2000 ...K8 1 ... 500 mm
020 Scraper
R8 Dust protection
Standard
-H- Note
The standards-based cylinder DNC can be ordered either using a fixed part num-
ber and order reference or using the modular product system.
The type codes listed above represent the standards-based cylinders DNC with
fixed part number and order reference only.
Variants can only be ordered using the modular product system.
Data sheet
Function
DNC-...
-N- Diameter
32 ... 125 mm
Without position sensing
-É- www.festo.com
Sets of wearing parts
• Standards-based cylinders to
a Page 24
DNC-...-A-... ISO 15552 (corresponds to the
With position sensing withdrawn standards ISO 6431,
DIN ISO 6431, VDMA 24562,
NF E 49 003.1 and UNI 10290)
Data sheet
Operating and environmental conditions
Piston @ 32 40 50 63 80 100 125
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on operating/ Lubricated operation possible (in which case lubricated operation will always be required)
pilot medium
Operating pressure 0.6 ... 12 0.6 ... 10
[bar]
Operating pressure R8 1.5 ... 12 1.5 ... 10
[bar] S11 After 10 strokes
0.16 ... 12 0.1 ... 12 0.06 ... 12 0.06 ... 10
After 24 h
0.3 ... 12 0.2 ... 12 0.1 ... 12 0.1 ... 10
Ambient temperature1) –20 ... +80
[°C] S6 0 ... 120
Corrosion resistance class CRC2) 2
R3 3
Maritime classification3) See certificate
ATEX Selected types a www.festo.com
1) Note operating range of proximity switches
2) Corrosion resistance class CRC 2 to Festo standard FN 940070
Moderate corrosion stress. Indoor applications in which condensation can occur. External visible parts with primarily decorative surface requirements which are in direct contact with a normal industrial environment.
Corrosion resistance class CRC 3 to Festo standard FN 940070
High corrosion stress. Outdoor exposure under moderate corrosive conditions. Externally visible parts with primarily functional surface requirements which are in direct contact with a normal industrial environment.
3) Additional information: www.festo.com/sp a Certificates
1) With variant K10 and S20, the permissible impact energy is reduced by approx. 10%
2 ∙ 𝐸𝐸𝐸𝐸
Permissible impact velocity: 𝑣𝑣𝑣𝑣 = � V Permissible impact velocity
𝑚𝑚𝑚𝑚1 + 𝑚𝑚𝑚𝑚2
E Max. impact energy -H- Note
m1 Moving mass (drive) These specifications represent the
Maximum permissible mass: 2 ∙ 𝐸𝐸𝐸𝐸 m2 Moving payload maximum values that can be
𝑚𝑚𝑚𝑚2 = 2 − 𝑚𝑚𝑚𝑚1
𝑣𝑣𝑣𝑣 achieved. The maximum permissible
impact energy must be observed.
Data sheet
Lateral force Fq as a function of stroke length l
DNC
Basic version
2000
1000
800 Fq
600
400
200
100
80
60
Fq [N]
40
20
10
8
6
4
1
10 20 40 60 80100 200 400 800 2000
l [mm]
@ 32
@ 40
@ 50/63
@ 80/100
@ 125
Data sheet
Max. transverse force Fq as a function of stroke length l and lever arm s
Q – Square piston rod
@ 32 @ 40
Max. torque = 800 Nmm/max. stroke = 300 mm Max. torque = 1100 Nmm/max. stroke = 400 mm
@ 50/63 @ 80/100
Max. torque = 1500 Nmm/max. stroke = 500 mm Max. torque = 3000 Nmm/max. stroke = 600 mm
Result: permissible
Fq= 8 N ‹ Fqmax. = 9.5 N
Data sheet
Weight [g]
Piston @ 32 40 50 63 80 100 125
Basic version
Product weight with 0 mm stroke 517 800 1260 1709 2790 4653 6771
Additional weight per 10 mm stroke 30 45 64 73 106 115 168
Moving mass with 0 mm stroke 162 307 538 663 1131 1544 2809
Add. moving mass per 10 mm stroke 9 16 25 25 38 38 63
Moving mass with 0 mm stroke 149 244 465 587 994 1399 –
Add. moving mass per 10 mm stroke 8 11 20 20 31 31 –
Moving mass with 0 mm stroke 170 330 560 711 1200 1660 2925
Add. moving mass per 10 mm stroke 18 32 50 50 76 76 126
Moving mass with 0 mm stroke 88 162 279 391 643 1029 1757
Add. moving mass per 10 mm stroke 3 6 8 9 13 13 22
Moving mass with 0 mm stroke 108 201 351 470 787 1184 2070
Add. moving mass per 10 mm stroke 6 11 17 17 26 26 43
Data sheet
Materials
Sectional view
3 2 1 2
Data sheet
Dimensions – Basic version Download CAD data a www.festo.com
[1] For mounting accessories: [2] Adjusting screw for adjustable [3] Sensor slot for proximity switch + = plus stroke length
@ 32 ... 100: Socket head screw end-position cushioning SME/SMT-8
with female thread
@ 125: Thread in cover
@ AM B BG E EE J2 J3 KK L1 L2
@
[mm] d11
32 22 30 16 45 G1/8 6 5.2 M10x1.25 18 94
40 24 35 16 54 G1/4 8 6 M12x1.25 21.5 105
50 32 40 17 64 G1/4 10.4 8.5 M16x1.5 28 106
63 32 45 17 75 G3/8 12.4 10 M16x1.5 28.5 121
80 40 45 17 93 G3/8 12.5 8 M20x1.5 34.7 128
100 40 55 17 110 G1/2 12 10 M20x1.5 38.2 138
125 54 60 22 134 G1/2 13 8 M27x2 46 160
@ L7 MM PL RT TG VA VD WH ZJ ß1 ß2 ß3
@
[mm]
32 3.3 12 15.6 M6 32.5 4 10 26 120 10 16 6
40 3.6 16 14 M6 38 4 10.5 30 135 13 18 6
50 5.1 20 14 M8 46.5 4 11.5 37 143 17 24 8
63 6.6 20 17 M8 56.5 4 15 37 158 17 24 8
80 10.5 25 16.4 M10 72 4 15.7 46 174 22 30 6
100 8 25 18.8 M10 89 4 19.2 51 189 22 30 6
125 14 32 18 M12 110 6 20.5 65 225 27 36 8
Data sheet
Dimensions – Variants Download CAD data a www.festo.com
Q – Square piston rod
@ B1 D8 ZJ ZM
™ @
[mm]
32 10 4.5 120 148
40 12 5.5 135 167
50 16 81) 143 183
63 16 8 158 199
80 20 11.7 174 222
100 20 11.7 189 240
125 – 13 225 291
Data sheet
Dimensions – Variants Download CAD data a www.festo.com
K2 – Extended male piston rod thread K3 – Female piston rod thread
-H- Note
In combination with variant S2/ In combination with variant Q, the
S20, the piston rod is extended at square piston rod is extended
one end.
@ A1 A2 AF AM KF KK T4 WH ß1
max. max. Basic thread Custom
[mm] thread1)
32 35 500 12 22 M6 M10x1.25 M10 2.6 26 10
40 35 500 12 24 M8 M12x1.25 M12 3.3 30 13
50 70 500 16 32 M10 M16x1.5 M16 4.7 37 17
63 70 500 16 32 M10 M16x1.5 M16 4.7 37 17
80 70 500 20 40 M12 M20x1.5 M20 6.1 46 22
100 70 500 20 40 M12 M20x1.5 M20 6.1 51 22
125 70 500 32 54 M16 M27x2 M27 8 65 27
1) The custom threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
Data sheet
Ordering data – Without position sensing
Piston @ Stroke Part no. Type1) Piston @ Stroke Part no. Type1)
[mm] [mm] [mm] [mm]
32 25 163319 DNC-32-25-PPV 40 25 163351 DNC-40-25-PPV
40 163320 DNC-32-40-PPV 40 163352 DNC-40-40-PPV
50 163321 DNC-32-50-PPV 50 163353 DNC-40-50-PPV
80 163322 DNC-32-80-PPV 80 163354 DNC-40-80-PPV
100 163323 DNC-32-100-PPV 100 163355 DNC-40-100-PPV
125 163324 DNC-32-125-PPV 125 163356 DNC-40-125-PPV
160 163325 DNC-32-160-PPV 160 163357 DNC-40-160-PPV
200 163326 DNC-32-200-PPV 200 163358 DNC-40-200-PPV
250 163327 DNC-32-250-PPV 250 163359 DNC-40-250-PPV
320 163328 DNC-32-320-PPV 320 163360 DNC-40-320-PPV
400 163329 DNC-32-400-PPV 400 163361 DNC-40-400-PPV
500 163330 DNC-32-500-PPV 500 163362 DNC-40-500-PPV
1) The mounting nut on the piston rod thread is included in the scope of delivery
Data sheet
Ordering data – With position sensing
Piston @ Stroke Part no. Type1) Piston @ Stroke Part no. Type1)
[mm] [mm] [mm] [mm]
32 20 1922617 DNC-32-20-PPV-A 40 20 1922623 DNC-40-20-PPV-A
25 163305 DNC-32-25-PPV-A 25 163337 DNC-40-25-PPV-A
30 1922618 DNC-32-30-PPV-A 30 1922624 DNC-40-30-PPV-A
40 163306 DNC-32-40-PPV-A 40 163338 DNC-40-40-PPV-A
50 163307 DNC-32-50-PPV-A 50 163339 DNC-40-50-PPV-A
60 1922619 DNC-32-60-PPV-A 60 1922625 DNC-40-60-PPV-A
70 1922620 DNC-32-70-PPV-A 70 1922626 DNC-40-70-PPV-A
80 163308 DNC-32-80-PPV-A 80 163340 DNC-40-80-PPV-A
100 163309 DNC-32-100-PPV-A 100 163341 DNC-40-100-PPV-A
125 163310 DNC-32-125-PPV-A 125 163342 DNC-40-125-PPV-A
150 1922621 DNC-32-150-PPV-A 150 1922627 DNC-40-150-PPV-A
160 163311 DNC-32-160-PPV-A 160 163343 DNC-40-160-PPV-A
200 163312 DNC-32-200-PPV-A 200 163344 DNC-40-200-PPV-A
250 163313 DNC-32-250-PPV-A 250 163345 DNC-40-250-PPV-A
300 1922622 DNC-32-300-PPV-A 300 1922628 DNC-40-300-PPV-A
320 163314 DNC-32-320-PPV-A 320 163346 DNC-40-320-PPV-A
400 163315 DNC-32-400-PPV-A 400 163347 DNC-40-400-PPV-A
500 163316 DNC-32-500-PPV-A 500 163348 DNC-40-500-PPV-A
1) The mounting nut on the piston rod thread is included in the scope of delivery
Data sheet
Ordering data – With position sensing
Piston @ Stroke Part no. Type1)
[mm] [mm]
80 20 1922641 DNC-80-20-PPV-A
25 163433 DNC-80-25-PPV-A
30 1922642 DNC-80-30-PPV-A
40 163434 DNC-80-40-PPV-A
50 163435 DNC-80-50-PPV-A
60 1922643 DNC-80-60-PPV-A
70 1922644 DNC-80-70-PPV-A
80 163436 DNC-80-80-PPV-A
100 163437 DNC-80-100-PPV-A
125 163438 DNC-80-125-PPV-A
150 1922645 DNC-80-150-PPV-A
160 163439 DNC-80-160-PPV-A
200 163440 DNC-80-200-PPV-A
250 163441 DNC-80-250-PPV-A
300 1922646 DNC-80-300-PPV-A
320 163442 DNC-80-320-PPV-A
400 163443 DNC-80-400-PPV-A
500 163444 DNC-80-500-PPV-A
1) The mounting nut on the piston rod thread is included in the scope of delivery
Data sheet
Ordering data – Variable stroke
Piston @ Stroke Without position sensing
[mm] [mm] Part no. Type1)
32 10 ... 2000 163318 DNC-32-...-PPV
40 10 ... 2000 163350 DNC-40-...-PPV
50 10 ... 2000 163382 DNC-50-...-PPV
63 10 ... 2000 163414 DNC-63-...-PPV
80 10 ... 2000 163446 DNC-80-...-PPV
100 10 ... 2000 163478 DNC-100-...-PPV
125 10 ... 2000 163510 DNC-125-...-PPV
1) The mounting nut on the piston rod thread is included in the scope of delivery
1) The mounting nut on the piston rod thread is included in the scope of delivery
Ordering data
Sets of wearing parts
Part no. Type Part no. Type
Piston @ Basic version S6 – Heat-resistant seals up to max. 120°C
32 369195 DNC-32-...-PPV-(A) 384214 DNC-32-...-PPV-(A)-S6
40 369196 DNC-40-...-PPV-(A) 384215 DNC-40-...-PPV-(A)-S6
50 369197 DNC-50-...-PPV-(A) 384216 DNC-50-...-PPV-(A)-S6
63 369198 DNC-63-...-PPV-(A) 384217 DNC-63-...-PPV-(A)-S6
80 369199 DNC-80-...-PPV-(A) 384218 DNC-80-...-PPV-(A)-S6
100 369200 DNC-100-...-PPV-(A) 384219 DNC-100-...-PPV-(A)-S6
125 369201 DNC-125-...-PPV-(A) 384220 DNC-125-...-PPV-(A)-S6
Data sheet
Function
DNC-...-KP
-N- Diameter
32 ... 125 mm
Without position sensing
-É- www.festo.com
Sets of wearing parts
DNC-...-A-...-KP
a Page 32
-H- Note
With position sensing If used in safety-relevant applications, Without additional measures in
additional measures are necessary, accordance with legally specified
e.g. in Europe the standards listed in minimum requirements, the prod-
the EC Machinery Directive must be uct is not suitable as a safety-re-
observed. lated component in control
systems.
Data sheet
Impact energy [J]
Piston @ 32 40 50 63 80 100 125
Max. impact energy at the end positions 0.1 0.2 0.2 0.5 0.9 1.2 5
2 ∙ 𝐸𝐸𝐸𝐸
Permissible impact velocity: 𝑣𝑣𝑣𝑣 = � V Permissible impact velocity
𝑚𝑚𝑚𝑚1 + 𝑚𝑚𝑚𝑚2
E Max. impact energy -H- Note
2 ∙ 𝐸𝐸𝐸𝐸 m1 Moving mass (drive) These specifications represent the
Maximum permissible mass: 𝑚𝑚𝑚𝑚2 = − 𝑚𝑚𝑚𝑚1 m2 Moving payload maximum values that can be
𝑣𝑣𝑣𝑣 2
achieved. The maximum permissible
impact energy must be observed.
Forces [N]
Piston @ 32 40 50 63 80 100 125
Theoretical force at 6 bar, 483 754 1 178 1870 3016 4712 7363
advancing S2 415 633 990 1682 2721 4418 6881
Theoretical force at 6 bar, retract- 415 633 990 1682 2721 4418 6881
ing S2 415 633 990 1682 2721 4418 6881
Static holding force 600 1000 1400 2000 5000 5000 7500
Data sheet
DNC
Max. transverse force Fq as a function of stroke length l
2000
1000
800 Fq
600
400
200
100
80
60
Fq [N]
40
20
10
8
6
4
2 @ 32
@ 40
1 @ 50/63
10 20 40 60 80100 200 400 800 2000 @ 80/100
l [mm] @ 125
Materials
Sectional view
2 3 1 2
4
7
5 6
Standards-based cylinder
[1] Profile barrel Smooth-anodised wrought aluminium alloy
[2] Bearing and end caps Die-cast aluminium
[3] Piston rod High-alloy steel
[4] Housing, clamping unit Anodised wrought aluminium alloy
[5] Clamping jaw Brass
[6] Spring Spring steel
[7] Piston Polyacetal
– Seals Polyurethane, nitrile rubber
Note on materials RoHS-compliant
Data sheet
Dimensions – Basic version Download CAD data a www.festo.com
[1] For mounting accessories: [2] Adjusting screw for adjustable [3] Sensor slot for proximity switch + = plus stroke length
@ 32 ... 100: Socket head screw end-position cushioning SME/SMT-8
with female thread
@ 125: Thread in cover
@ AM B BG D1 D2 E EE H1 J2 J3 KK L2 L3
@ @
[mm] d11 f9
32 22 30 16 20 M5 45 G1/8 67 6 5.2 M10x1.25 94 45
40 24 35 16 24 G1/8 54 G1/4 88 8 6 M12x1.25 105 53
50 32 40 17 30 G1/8 64 G1/4 107 10.4 8.5 M16x1.5 106 67
63 32 45 17 38 G1/8 75 G3/8 123 12.4 10 M16x1.5 121 76
80 40 45 17 48 G1/8 93 G3/8 165.5 12.5 8 M20x1.5 128 95
100 40 55 17 48 G1/8 110 G1/2 174 12 10 M20x1.5 138 98
125 54 60 22 65 G1/8 134 G1/2 207 13 8 M27x2 160 125
@ L5 L7 MM PL RT TG VA VD WH ZJ ß1 ß2 ß3
@
[mm]
32 14 3.3 12 15.6 M6 32.5 4 11.5 26 165 10 16 6
40 16 3.6 16 14 M6 38 4 11.5 30 188 13 18 6
50 20 5.1 20 14 M8 46.5 4 11 37 210 17 24 8
63 24 6.6 20 17 M8 56.5 4 11 37 234 17 24 8
80 31.5 10.5 25 16.4 M10 72 4 12.5 46 269 22 30 6
100 31 8 25 18.8 M10 89 4 12 51 287 22 30 6
125 42 14 32 18 M12 110 6 27.5 65 350 27 36 8
-H- Note
The dimensions for the cylinder/
valve combination are on
a page 44
Data sheet
Dimensions – Variants Download CAD data a www.festo.com
Q – Square piston rod
-H- Note
Clamping unit and variant Q only in
combination with S2
-H- Note
In combination with variant Q, the The clamping unit is mounted on
The thread types at both piston rod left-hand piston rod is round, the the left-hand, round piston rod.
ends are identical. right-hand piston rod square.
-H- Note
In combination with variant S2, the The clamping unit is mounted on If variant Q is also required, only
piston rod is extended at one end. the side of the piston rod that is the square piston rod is extended.
not extended.
@ A1 A2 AF AM B1 KF KK T4 WH ZJ ZM ß1
max. max. ™ Basic thread Custom
[mm] thread1)
32 35 500 12 22 10 M6 M10x1.25 M10 2.6 26 165 193 10
40 35 500 12 24 12 M8 M12x1.25 M12 3.3 30 188 220 13
50 70 500 16 32 16 M10 M16x1.5 M16 4.7 37 210 250 17
63 70 500 16 32 16 M10 M16x1.5 M16 4.7 37 234 275 17
80 70 500 20 40 20 M12 M20x1.5 M20 6.1 46 269 317 22
100 70 500 20 40 20 M12 M20x1.5 M20 6.1 51 287 338 22
125 70 500 32 54 – M16 M27x2 M27 8 65 350 416 27
1) The custom threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
Ordering data
Sets of wearing parts
Part no. Type
Piston @ Basic version
32 369195 DNC-32-...-PPV-(A)
40 369196 DNC-40-...-PPV-(A)
50 369197 DNC-50-...-PPV-(A)
63 369198 DNC-63-...-PPV-(A)
80 369199 DNC-80-...-PPV-(A)
100 369200 DNC-100-...-PPV-(A)
125 369201 DNC-125-...-PPV-(A)
Data sheet
Function
DNC-...-A-...-EL
--É- www.festo.com
With position sensing
Sets of wearing parts
a Page 24
-N- Diameter
32 ... 125 mm -H- Note.
If used in safety-relevant applications, Without additional measures in
-T- Stroke length additional measures are necessary, accordance with legally specified
10 ... 2000 mm e.g. in Europe the standards listed in minimum requirements, the prod-
the EC Machinery Directive must be uct is not suitable as a safety-re-
observed. lated component in control
systems
-H- Note
• End-position locking should only • Screws with a head or similar must • Locking can be activated from any • A very tightly set end-position
be used in conjunction with not be used in place of end-posi- stroke position once the drive is cushioning (more than 50%
double-acting cylinders with ex- tion locking, as there is a risk that brought mechanically into its end closed) can result in the locking
haust air flow control in order to the function will be impaired if position. bolt not engaging reliably, result-
ensure that the lock is always com- they are screwed in too deeply. • End-position locking has been ing in premature wear.
pletely released prior to starting • The exhaust bore must not be designed to prevent the load from
the drive movement. closed. dropping in case of pressure
failure.
Data sheet
Operating and environmental conditions
Piston @ 32 40 50 63 80 100
Operating medium Compressed air to ISO 8573-1:2010 [7:4:4]
Note on operating/ Lubricated operation possible (in which case lubricated operation will always be required)
pilot medium
Operating pressure [bar] 2.5 ... 12 1.5 ... 12
Ambient temperature1) [°C] –20 ... +80
Corrosion resistance class CRC2) 2
Maritime classification3) See certificate
2 ∙ 𝐸𝐸𝐸𝐸
Permissible impact velocity: 𝑣𝑣𝑣𝑣 = � V Permissible impact velocity
𝑚𝑚𝑚𝑚1 + 𝑚𝑚𝑚𝑚2
E Max. impact energy -H- Note
m1 Moving mass (drive) These specifications represent the
2 ∙ 𝐸𝐸𝐸𝐸
Maximum permissible mass: 𝑚𝑚𝑚𝑚2 = − 𝑚𝑚𝑚𝑚1 m2 Moving payload maximum values that can be
𝑣𝑣𝑣𝑣 2
achieved. The maximum permissible
impact energy must be observed.
Forces [N]
Piston @ 32 40 50 63 80 100
Theoretical force at 6 bar, advancing 483 754 1178 1870 3016 4712
Theoretical force at 6 bar, retracting 415 633 990 1682 2721 4418
Static holding force 500 2000 5000
Sizing example
Assuming: Example with 32 mm piston diameter:
-H- Note Mounting position = vertical Theoretical force at 6 bar, advancing = 483 N
When sizing pneumatic cylinders it is Workpiece load = 44 kg 50% of the theoretical force = 241.5 N
recommended as a basic principle F = m x g = 44 kg x 9.81 m/s2 Static holding force with 32 mm piston diameter = 500 N
that only 50% of the indicated theo- = 431.6 N The static holding force of end-position locking is within the permissible range
retical forces (see above) be used. (max. 500 N) for a workpiece load of 44 kg (431.6 N); however, the cylinder would
Required: be at 89% capacity.
Suitable piston diameter Result:
A cylinder with a piston diameter of 40 mm is therefore recommended for this
application.
Data sheet
DNC-EL
Max. transverse force Fq as a function of stroke length l
1000
800
600
500 Fq
400
300
200
100
80
60
50
40
Fq [N]
30
20
10
8
6
5
4
3
2
@ 32
1 @ 40
10 20 40 60 80100 200 400 800 2000
@ 50/63
l [mm] @ 80/100
Weight [g]
Piston @ 32 40 50 63 80 100
Basic version
Product weight with 0 mm stroke 537 820 1320 1769 2970 4833
Additional weight per 10 mm stroke 30 45 64 73 106 115
Materials
Sectional view
2 1 3 2
Standards-based cylinder
[1] Profile barrel Smooth-anodised wrought aluminium alloy
[2] Bearing and end caps Die-cast aluminium
[3] Piston rod High-alloy steel
– Seals Polyurethane, nitrile rubber
Note on materials RoHS-compliant
Data sheet
Dimensions – Basic version Download CAD data a www.festo.com
[1] Socket head screw with female [2] Adjusting screw for adjustable [3] Sensor slot for proximity switch + = plus stroke length
thread for mounting end-position cushioning
components
@ AM B BG D1 D2 E EE G H1 H2 J1 J2 J3 KK L1
@ @
[mm] d11 f8
1
@ L2 L3 L4 L7 MM PL RT TG VA VD WH ZM ZJ ß1 ß2 ß3
@
[mm] ±2
32 94 13.8 12 3.3 12 15.6 M6 32.5 4 10 26 148 120 10 16 6
40 105 16.6 16.6 3.6 16 14 M6 38 4 10.5 30 167 135 13 18 6
50 106 17.1 17.1 5.1 20 14 M8 46.5 4 11.5 37 183 143 17 24 8
63 121 16.6 16.6 6.6 20 17 M8 56.5 4 15 37 199 158 17 24 8
80 128 19.9 19.9 10.5 25 16.4 M10 72 4 15.7 46 222 174 22 30 6
100 138 22.8 22.8 8 25 18.8 M10 89 4 19.2 51 240 189 22 30 6
Data sheet
Dimensions – Variants Download CAD data a www.festo.com
K2 – Extended male piston rod thread
-H- Note
In combination with variant S2, the
piston rod is extended at one end.
@ A1 A2 AF AM KF KK T4 WH ß1
max. max. Basic thread Custom
[mm] thread1)
32 35 500 12 22 M6 M10x1.25 M10 2.6 26 10
40 35 500 12 24 M8 M12x1.25 M12 3.3 30 13
50 70 500 16 32 M10 M16x1.5 M16 4.7 37 17
63 70 500 16 32 M10 M16x1.5 M16 4.7 37 17
80 70 500 20 40 M12 M20x1.5 M20 6.1 46 22
100 70 500 20 40 M12 M20x1.5 M20 6.1 51 22
1) The custom threads are only available as male threads. The mounting nut on the piston rod thread is included in the scope of delivery
Data sheet
Function
DNC-...
-N- Diameter
32 ... 100 mm
Without position sensing
-É- www.festo.com
Sets of wearing parts
DNC-...-A-...
a Page 32
With position sensing
Valve variants
Single solenoid valve unactuated, piston rod retracted Double solenoid valve unactuated, piston rod retracted
DNC- ... -V1 – mounted on right DNC- ... -V3 – mounted on right
DNC- ... -V4 – mounted on left DNC- ... -V6 – mounted on right
-H- Note
Mounted on left or right refers to In this example, the valve is
looking at the piston rod from the mounted on the right.
front.
Data sheet
General technical data
Piston @ 32 40 50 63 80 100
Cylinder
Pneumatic connection G1/8 G1/4 G1/4 G3/8 G3/8 G1/2
Piston rod thread M10x1.25 M12x1.25 M16x1.5 M16x1.5 M20x1.5 M20x1.5
K3 M6 M8 M10 M10 M12 M12
K5 M10 M12 M16 M16 M20 M20
Design Piston
Piston rod
Profile barrel
Cushioning Elastic cushioning rings/pads at both ends
Pneumatic cushioning, adjustable at both ends
Cushioning length PPV [mm] 20 20 22 22 32 32
Position sensing Via proximity switch
Type of mounting With female thread
Via accessories
Mounting position Any
Data sheet
Forces [N] and impact energy [J]
Piston @ 32 40 50 63 80 100
Theoretical force at 6 bar, 483 754 1178 1870 3016 4712
advancing S2/S20 415 633 990 1682 2721 4418
Theoretical force at 6 bar, 415 633 990 1682 2721 4418
retracting S2/S20 415 633 990 1682 2721 4418
Max. impact energy at the end positions1) 0.1 0.2 0.2 0.5 0.9 1.2
1) With variant K10 and S20, the permissible impact energy is reduced by approx. 10%
2 ∙ 𝐸𝐸𝐸𝐸
Permissible impact velocity: V Permissible impact velocity
𝑣𝑣𝑣𝑣 = �
𝑚𝑚𝑚𝑚1 + 𝑚𝑚𝑚𝑚2
E Max. impact energy -H- Note
m1 Moving mass (drive) These specifications represent the
2 ∙ 𝐸𝐸𝐸𝐸
Maximum permissible mass: 𝑚𝑚𝑚𝑚2 = − 𝑚𝑚𝑚𝑚1 m2 Moving payload maximum values that can be
𝑣𝑣𝑣𝑣 2
achieved. The maximum permissible
impact energy must be observed.
DNC
Max. transverse load Fq as a function of stroke length l
2000
1000 Fq
800
600
400
200
100
80
60
Fq [N]
40
20
10
8
6
4
@ 32
1
10 20 40 60 80100 200 400 800 2000 @ 40
@ 50/63
l [mm]
@ 80/100
Data sheet
Materials
Sectional view
2 1 2
3 4
Data sheet
Dimensions Download CAD data a www.festo.com
[1] Connecting cable not included +1/2 = plus half stroke length
in scope of delivery
Data sheet
@ B1 B2 E1 H1 H2 L1 L2 L3 L4 L5 ß1 ß2
max.
[mm] ±3
32 62 59 G1/8 109+5.5 86+5.5 152 22 102 118 13 13 14
40 71 68 G1/8 114+5.5 94+5.5 152 23 102 118 13 17 14
50 85 82 G1/4 131+5.5 104+5.5 215 24 138 163 25 17 14
63 96 93 G1/4 142+5.5 115+5.5 215 25 138 163 25 19 14
80 123 119 G3/8 194+5.5 133+5.5 242 28 165 165 25 19 17
100 140 136 G3/8 213+2 158+2 242 30 165 165 25 27 17
-H- Note
Additional dimensions relating to the
basic type and its variants can be
found on
a page 15,
with clamping unit on
a page 28.
-H- Note
If feature ...K5 (custom thread) is
selected, the scope of delivery
does not include the piston rod
nut.
Accessories
Ordering data – Valves Data sheets a Internet: cpe
For @ Pneumatic connection Degree of Part no. Type
protection
[mm]
Single solenoid
32 G1/8 IP65 196941 CPE14-M1BH-5L-1/8
40
50 G1/4 IP65 163142 CPE18-M1H-5L-1/4
63
80 G3/8 IP65 163166 CPE24-M1H-5L-3/8
100
Double solenoid
32 G1/8 IP65 196939 CPE14-M1BH-5J-1/8
40
50 G1/4 IP65 163143 CPE18-M1H-5J-1/4
63
80 G3/8 IP65 163167 CPE24-M1H-5J-3/8
100
1) Packaging unit
Accessories
Multi-position kit DPNC
Material:
Flange: Wrought aluminium alloy
Threaded pins, hex nuts: Galvanised
steel
Free of copper and PTFE
RoHS-compliant + = plus stroke length
Connecting two cylinders with the same piston diameter to form a three- or four-position cylinder
A three or four-position cylinder con- This means that depending on the ac- against a stop. Note that when one end executes the movement. The connec-
sists of two separate cylinders whose tuation and stroke pattern, this type of of the piston rod is fixed, the cylinder tions to the cylinder must therefore be
piston rods advance in opposing cylinder can assume up to four posi- barrel flexible.
directions. tions. In each case the cylinder is
moved precisely
Accessories
Foot mounting HNC/CRHNC
Material:
HNC: Galvanised steel
CRHNC: high-alloy steel
Free of copper and PTFE
Accessories
Flange mounting FNC/CRFNG
Material:
FNC: Galvanised steel
CRFNG: high-alloy steel
Free of copper and PTFE
RoHS-compliant
Cannot be used on the bearing cap in
combination with bellows kit DADB.
+ = plus stroke length
Accessories
Trunnion flange ZNCF/CRZNG
Material:
ZNCF: Stainless steel casting
CRZNG: Electropolished stainless steel
casting
Free of copper and PTFE
RoHS-compliant
Cannot be used on the bearing cap in
combination with bellows kit DADB.
+ = plus stroke length
Accessories
Trunnion flange kit DAMT
for basic version DNC
Material:
High-alloy steel
Free of copper and PTFE
+ = plus stroke length
+ ½ = plus half stroke length [1] Max. tightening torque
for DNC-KP
Accessories
Trunnion support LNZG
Material:
Trunnion support: Anodised
aluminium
Plain bearing: Plastic
Free of copper and PTFE
RoHS-compliant
Material:
High-alloy steel
Free of copper and PTFE
RoHS-compliant
Accessories
Swivel flange SNC
Material:
Die-cast aluminium
Free of copper and PTFE
RoHS-compliant
Accessories
Swivel flange
SNCB/SNCB- ...-R3
Material:
SNCB: Die-cast aluminium
SNCB-...-R3: Die-cast aluminium with
protective coating
Free of copper and PTFE
RoHS-compliant + = plus stroke length
Accessories
Swivel flange
SNCS/CRSNCS/SNCS- ...-R3
Material:
SNCS 32 ... 50:
Die-cast aluminium
SNCS 63 ... 125:
Wrought aluminium alloy
CRSNCS 32 ... 80:
High-alloy stainless steel + = plus stroke length
SNCS-...-R3 100 ... 125:
Wrought aluminium alloy with
protective coating
RoHS-compliant
For @ MS RA TG XC
DNC-... DNC-...-R3 DNC-... DNC-...-R3 DNC-... DNC-...-KP
[mm] +1 +1
32 15+0.5 15+0.5 14.5 14.5 32.5 142 187
40 17+0.5 17+0.5 17.5 17.5 38 160 213
50 20+0.5 20+0.5 18.5 19 46.5 170 237
63 23–0.5 22+0.5 23 23 56.5 190 266
80 28–0.5 27+0.5 25 25 72 210 305
100 30±0.5 30±0.5 95 100 89 230 328
125 39±0.5 39±0.5 100 100 110 275 400
Accessories
Swivel flange SNCL
Material:
Die-cast aluminium
Free of copper and PTFE
RoHS-compliant
Accessories
Ordering data – Mounting components Data sheets a Internet: clevis foot
Designation For @ Part no. Type Designation For @ Part no. Type
Clevis foot LNG Clevis foot LSN
32 33890 LNG-32 32 5561 LSN-32
40 33891 LNG-40 40 5562 LSN-40
50 33892 LNG-50 50 5563 LSN-50
63 33893 LNG-63 63 5564 LSN-63
80 33894 LNG-80 80 5565 LSN-80
100 33895 LNG-100 100 5566 LSN-100
125 33896 LNG-125 125 6987 LSN-125
Ordering data – Mounting components, high corrosion protection Data sheets a Internet: clevis foot
Designation For @ Part no. Type
Clevis foot LBG-R3
32 2078790 LBG-32-R3
40 2078792 LBG-40-R3
50 2078794 LBG-50-R3
63 2078795 LBG-63-R3
80 2078797 LBG-80-R3
100 2078799 LBG-100-R3
125 2078837 LBG-125-R3
Accessories
Ordering data – Piston rod attachments Data sheets a Internet: piston rod attachment
Designation For @ Part no. Type Designation For @ Part no. Type
Rod eye SGS Rod clevis SGA
32 9261 SGS-M10x1.25 32 32954 SGA-M10x1.25
40 9262 SGS-M12x1.25 40 10767 SGA-M12x1.25
50 9263 SGS-M16x1.5 50 10768 SGA-M16x1.5
63 63
80 9264 SGS-M20x1.5 80 10769 SGA-M20x1.5
100 100
125 10774 SGS-M27x2 125 10770 SGA-M27x2
Adapter AD
32 157333 AD-M10x1.25-1/8
157334 AD-M10x1.25-1/4
40 160256 AD-M12x1.25-1/4
160257 AD-M12x1.25-3/8
Ordering data – Piston-rod attachments, corrosion-resistant Data sheets a Internet: piston rod attachment
Designation For @ Part no. Type Designation For @ Part no. Type
Rod eye CRSGS Rod clevis CRSG
32 195582 CRSGS-M10x1.25 32 13569 CRSG-M10x1.25
40 195583 CRSGS-M12x1.25 40 13570 CRSG-M12x1.25
50 195584 CRSGS-M16x1.5 50 13571 CRSG-M16x1.5
63 63
80 195585 CRSGS-M20x1.5 80 13572 CRSG-M20x1.5
100 100
125 195586 CRSGS-M27x2 125 185361 CRSG-M27x2
Accessories
Bellows kit DADB
Materials
Sectional view
Bellows
5 1 2 3 4
[1] Connection Polyamide
[2] Adapter Polyamide
[3] Bellows NBR
[4] End piece Polyamide
[5] Connector Polyamide
– O-ring NBR
Note on materials Free of copper and PTFE
RoHS-compliant
Weight [g]
Type DADB-V6- 32 40 50 63 80 100
Stroke [mm]
10 ... 50 29 42 71 69 99 124
51 ... 125 41 56 91 89 127 152
126 ... 175 52 68 105 103 140 165
176 ... 250 66 85 129 127 193 218
251 ... 300 79 100 147 145 231 255
301 ... 350 92 115 166 164 268 293
351 ... 375 92 115 167 165 259 284
376 ... 425 104 129 185 183 296 321
426 ... 475 117 144 204 202 334 359
476 ... 500 117 144 205 203 324 349
Accessories
Travel speed v as a function of tubing length l
The bellows kit is a leak-free system. The pressure generated in the bellows The recommended tubing length
To prevent unwanted media from being kit by the positioning motion is primar- based on the travel speed of the drive
drawn in, the supply and exhaust air ily defined by the travel speed and can be read from the graph.
must be ducted via a pressure com- tubing length.
pensation hole in the connection part
1
[1].
DADB-32
Advancing... 100 DADB-32
Retracting... 100
1.2 1.2
1 1
0.8 0.8
v [m/s]
v [m/s]
0.6 0.6
0.4 0.4
0.2 0.2
0 0
0 1 2 3 4 5 6 7 8 9 10 0 1 2 3 4 5 6 7 8 9 10
l [m] l [m]
@ 32/50/63 @ 32
@ 40 @ 40
@ 80/100 @ 50/63
@ 80/100
Accessories
Dimensions Download CAD data a www.festo.com
@ 32 40
Stroke A21) D1 D2 EE L1 L2 WH+A2 A21) D1 D2 EE L1 L2 WH+A2
[mm] max. max.
10 ... 50 29 55 28 58
51 ... 125 47 73 43 73
126 ... 175 61 87 56 86
176 ... 250 80 106 72 102
251 ... 300 96 122 86 116
38 14 G1/8 12.9 5.4 46 14 G1/8 16.3 5.4
301 ... 350 112 138 100 130
351 ... 375 114 140 101 131
376 ... 425 130 156 115 145
426 ... 475 145 171 130 160
476 ... 500 147 173 131 161
@ 50 63
Stroke A21) D1 D2 EE L1 L2 WH+A2 A21) D1 D2 EE L1 L2 WH+A2
[mm] max. max.
10 ... 50 28 65 28 65
51 ... 125 46 83 46 83
126 ... 175 56 93 56 93
176 ... 250 73 110 73 110
251 ... 300 86 123 86 123
57 17 G1/4 22.35 7 57 17 G1/4 22.4 7
301 ... 350 97 134 97 134
351 ... 375 105 142 105 142
376 ... 425 116 153 116 153
426 ... 475 126 163 126 163
476 ... 500 134 171 134 171
@ 80 100
Stroke A21) D1 D2 EE L1 L2 WH+A2 A21) D1 D2 EE L1 L2 WH+A2
[mm] max. max.
10 ... 50 25 71 25 71
51 ... 125 37 83 37 83
126 ... 175 49 95 49 95
176 ... 250 62 108 62 108
251 ... 300 74 120 74 120
93 17 G1/4 28 4 93 17 G1/4 28 4
301 ... 350 86 132 86 132
351 ... 375 87 133 87 133
376 ... 425 98 144 98 144
426 ... 475 110 156 110 156
476 ... 500 111 157 111 157
1) The dimension corresponds to the K8 value (advanced piston rod) of the drive
Accessories
Ordering data – Bellows kit
An extended piston rod (order code K8) The necessary dimension for K8 as a Order example:
is absolutely essential when using a function of piston diameter and cylin- Selected standards-based cylinder:
bellows kit a Ordering data – der stroke as well as the corresponding DNC-32-320-PPV-A-...
Modular product system. bellows kit is indicated in the table The dimension for the corresponding K8 value (see table):
below: 112 mm
Complete order reference for standards-based cylinder:
DNC-32-320-PPV-A-...-112K8
The corresponding bellows kit:
DADB-V6-32-S301-350
Accessories
Ordering data – Guide units for fixed strokes (recirculating ball bearing guide only) Data sheets a Internet: feng
Stroke Part no. Type Stroke Part no. Type
[mm] [mm]
For @ 32 mm For @ 40 mm
10 ... 50 34493 FENG-32-50-KF 10 ... 50 34499 FENG-40-50-KF
10 ... 100 34494 FENG-32-100-KF 10 ... 100 34500 FENG-40-100-KF
10 ... 160 34495 FENG-32-160-KF 10 ... 160 34501 FENG-40-160-KF
10 ... 200 34496 FENG-32-200-KF 10 ... 200 34502 FENG-40-200-KF
10 ... 250 150289 FENG-32-250-KF 10 ... 250 34503 FENG-40-250-KF
10 ... 320 34497 FENG-32-320-KF 10 ... 320 34504 FENG-40-320-KF
10 ... 400 150290 FENG-32-400-KF 10 ... 400 150291 FENG-40-400-KF
10 ... 500 34498 FENG-32-500-KF 10 ... 500 34505 FENG-40-500-KF
Ordering data – Guide units for variable strokes Data sheets a Internet: feng
For @ Stroke With recirculating ball bearing guide With plain-bearing guide
[mm] [mm] Part no. Type Part no. Type
32 10 ... 500 34487 FENG-32-...-KF 34481 FENG-32-...-GF
40 10 ... 500 34488 FENG-40-...-KF 34482 FENG-40-...-GF
50 10 ... 500 34489 FENG-50-...-KF 34483 FENG-50-...-GF
63 10 ... 500 34490 FENG-63-...-KF 34484 FENG-63-...-GF
80 10 ... 500 34491 FENG-80-...-KF 34485 FENG-80-...-GF
100 10 ... 500 34492 FENG-100-...-KF 34486 FENG-100-...-GF
Ordering data – Mounting kits for proximity switch SMT-8 Data sheets a Internet: smb
For @ [mm] Part no. Type
32 175705 SMB-8-FENG-32/40
40
50 175706 SMB-8-FENG-50/63
63
80 175707 SMB-8-FENG-80/100
100
Accessories
Ordering data – Proximity switch for T-slot, magneto-resistive Data sheets a Internet: smt
Type of mounting Switching Electrical connection Cable length Part no. Type
output [m]
N/O contact
Inserted in the slot from above, PNP Cable, 3-wire 2.5 574335 SMT-8M-A-PS-24V-E-2.5-OE
flush with the cylinder profile, Plug M8x1, 3-pin 0.3 574334 SMT-8M-A-PS-24V-E-0.3-M8D
short design Plug M12x1, 3-pin 0.3 574337 SMT-8M-A-PS-24V-E-0.3-M12
NPN Cable, 3-wire 2.5 574338 SMT-8M-A-NS-24V-E-2.5-OE
Plug M8x1, 3-pin 0.3 574339 SMT-8M-A-NS-24V-E-0.3-M8D
N/C contact
Inserted in the slot from above, PNP Cable, 3-wire 7.5 574340 SMT-8M-A-PO-24V-E-7.5-OE
flush with the cylinder profile,
short design
Ordering data – Proximity switch for T-slot, magnetic reed Data sheets a Internet: sme
Type of mounting Switching Electrical connection Cable length Part no. Type
output [m]
N/O contact
Inserted in the slot from above, flush with the Contacting Cable, 3-wire 2.5 543862 SME-8M-DS-24V-K-2.5-OE
cylinder profile 5.0 543863 SME-8M-DS-24V-K-5.0-OE
Cable, 2-wire 2.5 543872 SME-8M-ZS-24V-K-2.5-OE
Plug M8x1, 3-pin 0.3 543861 SME-8M-DS-24V-K-0.3-M8D
Inserted in the slot lengthwise, flush with the Contacting Cable, 3-wire 2.5 150855 SME-8-K-LED-24
cylinder profile Plug M8x1, 3-pin 0.3 150857 SME-8-S-LED-24
N/C contact
Inserted in the slot lengthwise, flush with the Contacting Cable, 3-wire 7.5 160251 SME-8-O-K-LED-24
cylinder profile
Accessories
Ordering data – One-way flow control valves Data sheets a Internet: grla
Connection Material Part no. Type
Thread For tubing O.D.
G1/8 3 Metal design 193142 GRLA-1/8-QS-3-D
4 193143 GRLA-1/8-QS-4-D
6 193144 GRLA-1/8-QS-6-D
8 193145 GRLA-1/8-QS-8-D
G1/4 6 193146 GRLA-1/4-QS-6-D
8 193147 GRLA-1/4-QS-8-D
10 193148 GRLA-1/4-QS-10-D
G3/8 6 193149 GRLA-3/8-QS-6-D
8 193150 GRLA-3/8-QS-8-D
10 193151 GRLA-3/8-QS-10-D
G1/2 12 193152 GRLA-1/2-QS-12-D
Festo Customer Interaction Center Multinational Contact Center Festo Customer Interaction Center
Tel: 1 877 463 3786 01 800 337 8669 1 800 993 3786
Fax: 1 877 393 3786 1 800 963 3786
Email: customer.service.ca@festo.com ventas.mexico@festo.com customer.service.us@festo.com
Subject to change
Connect with us
www.festo.com/socialmedia www.festo.com