Professional Documents
Culture Documents
Pump Division
AFV
Vertical
Axial Flow
Pumps
Pump Division
Pump Division
Submersible
Motor
LNN
Concrete
Volute
3
(PS-40-3) AFV 10/8/03 3:44 PM Page 4
Pump Division
AFV The AFV axial flow suspended AFV Design with AFV Advantages Over
shaft vertical pump is a single Sealed Bearing Lubrication Horizontal Units
Vertical stage propeller type machine. • Self-priming
Axial Flow This family of pumps is • Minimum floor space
specifically designed for low requirements
Pumps • Simple, low cost
head movement of water for a
multitude of municipal, agricul- foundation design and
tural and industrial services. installation
• Above or below grade
Their simple but heavy
discharge to suit site
construction, multiple hydraulic
conditions
combinations and available
• Inherent self-alignment
design features provide
resulting from tight
trouble-free, continuous
tolerance machining of
capabilities with high
shoulders and recesses
operating efficiency.
Vertical Hollow Shaft
Models Available
Motor Option
• Above ground discharge
• Allows pump headshaft
– AFS: Flanged discharge
to extend through the
– APS: Plain end discharge
motor, providing easy
• Below ground discharge
access for impeller
– BFS: Flanged discharge
clearance adjustment
– BPS: Plain end discharge
• Adjusting nut located
at the top of motor
Operating Parameters
• Two-piece headshaft
• Flows to 180 000 m3/h
with motor stand
(800 000 gpm)
available where overhead
• Heads to 11 m (35 ft)
clearance is insufficient
• Speeds to 1770 rpm
to remove motor
• Sizes 200 mm (8 in)
to 3.1 m (123 in)
Vertical Solid Shaft
• Settings to 8 m (25 ft)
Motor Option
• Supplied by customer
specification or
preference
• Rigid coupling provided
between motor and
pump for shaft
diameters greater
than 75 mm (3 in)
Pump Division
Construction Options
Discharge Head • Cast for sizes to 500 mm (20 in)
• Fabricated for sizes over 500 mm (20 in)
Optional Case and Bowl Assembly • Cast for sizes 200 mm (8 in) to
Impeller Wear Rings 685 mm (27 in)
– Impeller liner type standard
– Impeller case type optional
• Fabricated for sizes over 685 mm (27 in)
optional
Impeller Casing • Integral with suction bell, one-piece casting
or fabricated, depending on specifications
and pump size
Impeller Features
• 3- or 4-vane axial flow design
• Mechanically balanced
• Profiled and finished vane
surfaces
• Key-driven with split
retaining ring
Cast Bowl Assembly
• Hydraulically balanced to
Impeller - Case Type
reduce axial down thrust
Pump Division
150
200
m3/h
1 0.3
0.5
0.8
1.0
2.5
5.0
7.5
10
100 25
50
75
gpm
0
6
8
10
20
40
60
80
200
400
600
800
1000
ft m ft m
50 15
30 10
40
7
20 30 10
5 7
20
TDH - 50 Hz
TDH - 60 Hz
5
10 3
7 10 3
2
5 1.5 7
2
4
5 1.5
3 1
0.7 4
150
0.3
0.8
1.0
2.5
5.0
7.5
10
100 25
50
75
m3/h
.5
gpm
0
6
8
10
20
40
60
80
200
400
600
800
6
(PS-40-3) AFV 10/8/03 3:47 PM Page 7
Pump Division
7
(PS-40-3) AFV 10/8/03 3:47 PM Page 8
Jeumont-Schneider™
Printed in U.S.A.
October 2003
© Flowserve Corporation