Professional Documents
Culture Documents
Question 1
Correct
The lifting capacity on lower links for MF 241 tractor in Horizontal position is ______
Select one:
a. 1700 Kg
b. 1850 KG
c. 1550 Kg
d. 2050 Kg
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 1/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 2
Correct
Mark 1.00 out of 1.00
Select one:
a. Relief Valve
Question 3
Incorrect
Mark 0.00 out of 1.00
Which part is the key to achieve the slow response control of mark 1A hydraulic system?
Select one:
a. Eccentric roller
b. Relief valve
c. Mango cam
d. Control spring assembly
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 2/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 4
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement is coming down by its own after pressing the clutch pedal fully?
Select one:
Question 5
Correct
Mark 1.00 out of 1.00
How many supports are there for hydraulic pump so as to hold it in floating position?
Select one:
a. 4
b. 3
c. 5
d. 6
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 3/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 6
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for tipping trailer not lifting by DC lever in MF 1035 DI tractor?
Select one:
a. Eccentric roller setting may be wrong
b. Response control setting may be wrong
c. Position control setting may be wrong
Question 7
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for slow response not obtained in mark 1A hydraulics tractor?
Select one:
a. Transmission oil level may be low
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 4/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 8
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement jerking while lifting?
Select one:
a. Worn out control valve
b. Strainer choked
c. Control spring setting is loose
Question 9
Correct
Mark 1.00 out of 1.00
What is the type of hydraulic pump used in TAFE Tractors?
Select one:
a. Centrifugal
b. Gear
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 5/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 10
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet port open and out port closed
b. Inlet and outlet ports are closed
c. Inlet and outlet ports are open
Question 11
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement jerking while lowering?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 6/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 12
Correct
Mark 1.00 out of 1.00
Select one:
Question 13
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement not lifting in MF 241 DI tractor?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 7/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 14
Incorrect
Mark 0.00 out of 1.00
What is the advantages of “up lift kit” used in MF 7250 non tandem pump tractors?
Select one:
a. Implement lowering speed will be faster
Question 15
Correct
Mark 1.00 out of 1.00
How much weight should be added on the vertical lever, while doing the vertical lever settings in MARK IA Hydraulic lift cover?
Select one:
a. 5 lbs.
b. 4 lbs.
c. 3 lbs.
d. 6 lbs.
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 8/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 16
Correct
Mark 1.00 out of 1.00
What is the position of control valve after lower link being fully lifted by PC lever?
Select one:
a. Neutral
b. Lift
c. Fast drop
d. Slow drop
Question 17
Correct
Mark 1.00 out of 1.00
Select one:
a. Counter shaft
b. Main shaft
c. Rear drive shaft
d. PTO shaft
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 9/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 18
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for control valve stuck up at lift position in Mark 1A hydraulic pump?
Select one:
a. Worn out drive pin
Question 19
Correct
Mark 1.00 out of 1.00
What is the function of control valve spring (3 pounds) in hydraulic system?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 10/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 20
Incorrect
Mark 0.00 out of 1.00
During rotary tiller field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever – Fast or Position range, DC lever – Sector mark and depth controlled by PC lever
b. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
c. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
d. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
Question 21
Correct
Mark 1.00 out of 1.00
How much weight to be added approximately on the lower links before doing the external settings in MARK IA Hydraulics?
Select one:
a. 1250 Kg
b. 400 Kg
c. 1100 Kg
d. 850 Kg
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 11/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 22
Correct
Mark 1.00 out of 1.00
Select one:
a. Slow, Fast, Neutral, Lift
b. Lift, Slow, Fast, Neutral
Question 23
Correct
Mark 1.00 out of 1.00
During mould board plough field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
b. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
c. PC lever – Position range, DC lever – Sector mark and depth controlled by PC lever
d. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 12/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 24
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement not lifting and relief valve is blowing in MF 241 DI tractor?
Select one:
a. Transport lock valve is closed
b. Worn out primary clutch plate
Question 25
Incorrect
Mark 0.00 out of 1.00
The pressure relief valve starts open at ____ and the system pressure must not to exceed ____ in MARK IA Hydraulic pump fitted in MF 241?
Select one:
a. 2700 PSI, 2800 PSI
b. 2300 PSI, 2800 PSI
c. 2700 PSI, 3100 PSI
d. 2400 PSI, 2600 PSI
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 13/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6335&cmid=212 14/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 1
Correct
During rotary tiller field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
b. PC lever – Fast or Position range, DC lever – Sector mark and depth controlled by PC lever
c. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
d. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 1/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 2
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement is coming down by its own after pressing the clutch pedal fully?
Select one:
a. Worn out secondary clutch plate
b. Worn out primary clutch plate
c. Low engine power
Question 3
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for low depth of cut in mould board plough operation with MF 1035 DI tractor?
Select one:
a. Position control setting guide rod nut may be over tighten
b. Eccentric roller setting may be wrong
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 2/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 4
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the slow response control of mark 1A hydraulic system?
Select one:
a. Control spring assembly
b. Relief valve
c. Mango cam
d. Eccentric roller
Question 5
Incorrect
Mark 0.00 out of 1.00
What is the advantages of “up lift kit” used in MF 7250 non tandem pump tractors?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 3/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 6
Correct
Mark 1.00 out of 1.00
How much weight should be added on the vertical lever, while doing the vertical lever settings in MARK IA Hydraulic lift cover?
Select one:
a. 6 lbs.
b. 4 lbs.
c. 5 lbs.
d. 3 lbs.
Question 7
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for control valve stuck up at lift position in Mark 1A hydraulic pump?
Select one:
a. Implement weight is high
b. Worn out clutch plate
c. Implement weight is low
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 4/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 8
Correct
Mark 1.00 out of 1.00
How much weight to be added approximately on the lower links before doing the external settings in MARK IA Hydraulics?
Select one:
a. 400 Kg
b. 850 Kg
c. 1250 Kg
d. 1100 Kg
Question 9
Correct
Mark 1.00 out of 1.00
What is the type of hydraulic pump used in TAFE Tractors?
Select one:
a. Gear
b. Rotor
c. Centrifugal
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 5/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 10
Correct
Mark 1.00 out of 1.00
Select one:
a. Strainer
Question 11
Correct
Mark 1.00 out of 1.00
In slow drop position of the control valve, ___________________
Select one:
a. Inlet port open and out port closed
b. Inlet and outlet ports are open
c. Inlet and outlet ports are closed
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 6/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 12
Correct
Mark 1.00 out of 1.00
The lifting capacity on lower links for MF 241 tractor in Horizontal position is ______
Select one:
a. 1550 Kg
b. 1850 KG
c. 2050 Kg
d. 1700 Kg
Question 13
Correct
Mark 1.00 out of 1.00
The inlet port of the control valve is connected to the _______________
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 7/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 14
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the draft control of hydraulic system?
Select one:
a. Mango cam
b. Relief valve
c. Eccentric roller
Question 15
Correct
Mark 1.00 out of 1.00
What is the position of control valve when the PC lever is moved to up position and lower link is started raising?
Select one:
a. Fast drop
b. Neutral
c. Lift
d. Slow drop
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 8/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 16
Correct
Mark 1.00 out of 1.00
The pressure relief valve starts open at ____ and the system pressure must not to exceed ____ in MARK IA Hydraulic pump fitted in MF 241?
Select one:
Question 17
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the position control of hydraulic system?
Select one:
a. Eccentric roller
b. Mango cam
c. Relief valve
d. Control spring assembly
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 9/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 18
Correct
Mark 1.00 out of 1.00
How the “up lift kit” lever is connected to control valve actuating lever in MF 7250?
Select one:
Question 19
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement not lifting in MF 241 DI tractor?
Select one:
a. Worn out primary clutch plate
b. Draft control lever may be below the sector mark Draft
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 10/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 20
Correct
Mark 1.00 out of 1.00
Select one:
a. Helps to obtain fast response
b. Provides smooth movements to control valve
Question 21
Correct
Mark 1.00 out of 1.00
In lift position of the control valve ___________________
Select one:
a. Inlet and outlet ports are closed
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 11/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 22
Correct
Mark 1.00 out of 1.00
How many supports are there for hydraulic pump so as to hold it in floating position?
Select one:
a. 5
b. 3
c. 6
d. 4
Question 23
Correct
Mark 1.00 out of 1.00
What will be the effect of actuating lever self-locking nut setting is loose?
Select one:
a. Transport height may not obtained
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 12/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 24
Correct
Mark 1.00 out of 1.00
Select one:
Question 25
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for tipping trailer not lifting by DC lever in MF 1035 DI tractor?
Select one:
a. Position control setting may be wrong
b. Eccentric roller setting may be wrong
c. Response control setting may be wrong
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 13/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6359&cmid=212 14/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 1
Correct
Select one:
a. Inlet port open and out port closed
b. Inlet and outlet ports are open
c. Inlet port closed and outlet port fully open
d. Inlet outlet ports are closed
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 1/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 2
Correct
Mark 1.00 out of 1.00
How do you lift the hydraulically operated tipping trailer and how do you stop lifting trailer in MF 1035 DI tractor?
Select one:
a. PC lever – Fully up, DC lever – below sector mark to lift and make manual neutral by PC lever to stop
b. PC lever – Fast or slow, DC lever – Above sector mark to lift and make manual neutral by DC lever to stop
c. PC lever – Fast, DC lever – Sector mark to lift and make manual neutral by DC lever to stop
d. PC lever – Fully up, DC lever – Sector mark to lift and make manual neutral by DC lever to stop
Question 3
Correct
Mark 1.00 out of 1.00
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 2/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 4
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the position control of hydraulic system?
Select one:
a. Control spring assembly
b. Relief valve
c. Mango cam
d. Eccentric roller
Question 5
Correct
Mark 1.00 out of 1.00
Select one:
a. Lift
b. Up
c. Drop
d. Neutral
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 3/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 6
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the draft control of hydraulic system?
Select one:
a. Mango cam
b. Eccentric roller
Question 7
Correct
Mark 1.00 out of 1.00
What will be the effect of actuating lever self-locking nut setting is loose?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 4/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 8
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet port closed and outlet port open
b. Inlet and outlet ports are closed
c. Inlet and outlet ports are open
Question 9
Correct
Mark 1.00 out of 1.00
What is the position of control valve when the PC lever is moved to up position and lower link is started raising?
Select one:
a. Slow drop
b. Fast drop
c. Neutral
d. Lift
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 5/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 10
Correct
Mark 1.00 out of 1.00
Where will you keep the control levers, while doing internal settings in MARK IA Hydraulic Lift Cover?
Select one:
a. PC- Slow Drop, DC- Sector mark and Lift Arm- Middle position
b. PC- Fast Drop, DC- Sector mark and Lift Arm- Fully down
c. PC- Fast Drop, DC- Below Sector mark and Lift Arm- Fully Up
d. PC- Slow Drop, DC- Above Sector mark and Lift Arm- Fully down
Question 11
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for fast response is not obtained in MF 1035 DI?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 6/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 12
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement jerking after fully lifted?
Select one:
a. Worn out control valve
b. Strainer choked
Question 13
Correct
Mark 1.00 out of 1.00
How the “up lift kit” lever is connected to control valve actuating lever in MF 7250?
Select one:
a. Through DC linkages
b. Through PC linkages
c. Through response linkages
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 7/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 14
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for low depth of cut in mould board plough operation with MF 1035 DI tractor?
Select one:
a. Draft control setting guide rod nut may be over tighten
b. Position control setting guide rod nut may be over tighten
Question 15
Correct
Mark 1.00 out of 1.00
By which method you will ensure that, the control spring free length setting is correct?
Select one:
a. Free to rotate by 2 fingers and Hard to rotate by 3 fingers
b. Free to rotate by 3 fingers and Hard to rotate by 5 fingers
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 8/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 16
Correct
Mark 1.00 out of 1.00
Select one:
a. 17/52*ERPM
b. 19/61*ERPM
c. 18/50*ERPM
d. 16/53*ERPM
Question 17
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet and outlet ports are open
b. Inlet port open and out port closed
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 9/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 18
Correct
Mark 1.00 out of 1.00
Select one:
a. Intake housing
Question 19
Correct
Mark 1.00 out of 1.00
How much weight to be added approximately on the lower links before doing the external settings in MARK IA Hydraulics?
Select one:
a. 1100 Kg
b. 400 Kg
c. 1250 Kg
d. 850 Kg
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 10/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 20
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for tipping trailer not lifting by DC lever in MF 1035 DI tractor?
Select one:
a. Position control setting may be wrong
Question 21
Correct
Mark 1.00 out of 1.00
During mould board plough field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
b. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
c. PC lever – Position range, DC lever – Sector mark and depth controlled by PC lever
d. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 11/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 22
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement jerking while lifting?
Select one:
a. Valve chamber outlet valve leakage
b. Worn out control valve
c. Control spring setting is loose
d. Strainer choked
Question 23
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement jerking while lowering?
Select one:
a. Worn out control valve
b. Strainer choked
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 12/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 24
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for slow response not obtained in mark 1A hydraulics tractor?
Select one:
a. No gap between differential cam and eccentric roller
Question 25
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement not lifting in MF 241 DI tractor?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 13/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6366&cmid=212 14/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 1
Correct
What could be the one of the cause for implement is coming down by its own after pressing the clutch pedal fully?
Select one:
a. Worn out primary clutch plate
b. Worn out secondary clutch plate
c. Low engine power
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 1/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 2
Correct
Mark 1.00 out of 1.00
What is the position of control valve after lower link being fully lifted by PC lever?
Select one:
a. Lift
b. Fast drop
c. Neutral
d. Slow drop
Question 3
Correct
Mark 1.00 out of 1.00
What is the speed of Hydraulic pump in MF 245 tractor?
Select one:
a. 18/50*ERPM
b. 16/53*ERPM
c. 19/61*ERPM
d. 17/52*ERPM
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 2/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 4
Correct
Mark 1.00 out of 1.00
Select one:
Question 5
Correct
Mark 1.00 out of 1.00
In neutral position of the control valve ___________________
Select one:
a. Inlet port closed and outlet port open
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 3/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 6
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement jerking while lifting?
Select one:
a. Worn out control valve
b. Control spring setting is loose
c. Valve chamber outlet valve leakage
d. Strainer choked
Question 7
Correct
Mark 1.00 out of 1.00
During rotary tiller field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
b. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
c. PC lever – Fast or Position range, DC lever – Sector mark and depth controlled by PC lever
d. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 4/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 8
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet and outlet ports are open
b. Inlet and outlet ports are closed
Question 9
Correct
Mark 1.00 out of 1.00
In slow drop position of the control valve, ___________________
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 5/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 10
Correct
Mark 1.00 out of 1.00
Where will you keep the control levers, while doing internal settings in MARK IA Hydraulic Lift Cover?
Select one:
a. PC- Fast Drop, DC- Below Sector mark and Lift Arm- Fully Up
b. PC- Slow Drop, DC- Sector mark and Lift Arm- Middle position
c. PC- Slow Drop, DC- Above Sector mark and Lift Arm- Fully down
d. PC- Fast Drop, DC- Sector mark and Lift Arm- Fully down
Question 11
Correct
Mark 1.00 out of 1.00
By which method you will ensure that, the control spring free length setting is correct?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 6/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 12
Correct
Mark 1.00 out of 1.00
The pressure relief valve starts open at ____ and the system pressure must not to exceed ____ in MARK IA Hydraulic pump fitted in MF 241?
Select one:
a. 2700 PSI, 2800 PSI
b. 2400 PSI, 2600 PSI
Question 13
Correct
Mark 1.00 out of 1.00
How many supports are there for hydraulic pump so as to hold it in floating position?
Select one:
a. 4
b. 3
c. 5
d. 6
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 7/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 14
Correct
Mark 1.00 out of 1.00
Select one:
Question 15
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the position control of hydraulic system?
Select one:
a. Control spring assembly
b. Eccentric roller
c. Relief valve
d. Mango cam
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 8/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 16
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement not lifting and relief valve is blowing in MF 241 DI tractor?
Select one:
Question 17
Correct
Mark 1.00 out of 1.00
What is the position of control valve when the PC lever is moved to up position and lower link is started raising?
Select one:
a. Fast drop
b. Lift
c. Slow drop
d. Neutral
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 9/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 18
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for slow response not obtained in mark 1A hydraulics tractor?
Select one:
a. Transmission oil level may be low
Question 19
Correct
Mark 1.00 out of 1.00
The lifting capacity on lower links for MF 241 tractor in Horizontal position is ______
Select one:
a. 1550 Kg
b. 2050 Kg
c. 1850 KG
d. 1700 Kg
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 10/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 20
Correct
Mark 1.00 out of 1.00
Select one:
a. Helps to obtain fast response
b. Provides smooth movements to control valve
Question 21
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for low depth of cut in mould board plough operation with MF 1035 DI tractor?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 11/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 22
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for tipping trailer not lifting by DC lever in MF 1035 DI tractor?
Select one:
a. Position control setting may be wrong
b. Response control setting may be wrong
c. Eccentric roller setting may be wrong
Question 23
Correct
Mark 1.00 out of 1.00
During mould board plough field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever – Position range, DC lever – Sector mark and depth controlled by PC lever
b. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
c. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
d. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 12/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 24
Correct
Mark 1.00 out of 1.00
How the “up lift kit” lever is connected to control valve actuating lever in MF 7250?
Select one:
Question 25
Correct
Mark 1.00 out of 1.00
Name the different positions of control valve in sequence?
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 13/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6363&cmid=212 14/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 1
Incorrect
What could be the one of the cause for implement jerking after fully lifted?
Select one:
a. Worn out control valve
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 1/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 2
Correct
Mark 1.00 out of 1.00
Select one:
Question 3
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for slow response not obtained in mark 1A hydraulics tractor?
Select one:
a. Draft control lever may be below sector mark
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 2/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 4
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for tipping trailer not lifting by DC lever in MF 1035 DI tractor?
Select one:
a. Eccentric roller setting may be wrong
Question 5
Correct
Mark 1.00 out of 1.00
By which method you will ensure that, the control spring free length setting is correct?
Select one:
a. Free to rotate by 3 fingers and Hard to rotate by 5 fingers
b. Hard to rotate by 5 fingers and Free to rotate by 3 fingers
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 3/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 6
Incorrect
Mark 0.00 out of 1.00
During mould board plough field operation, where will be place the hydraulic control levers in MF 241 DI tractor?
Select one:
a. PC lever – Fast, DC lever – above sector mark and depth controlled by PC lever
b. PC lever – Position range, DC lever – Sector mark and depth controlled by PC lever
c. PC lever – Fully up, DC lever – Sector mark and draft controlled by DC lever
d. PC lever - Fast or Slow, DC lever – Sector mark and draft controlled by DC lever
Question 7
Incorrect
Mark 0.00 out of 1.00
What is the position of control valve, while wheel started slipping?
Select one:
a. Up
b. Lift
c. Neutral
d. Drop
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 4/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 8
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for implement jerking while lowering?
Select one:
a. Strainer choked
b. Valve chamber outlet valve leakage
c. Worn out control valve
Question 9
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement not lifting and relief valve is blowing in MF 241 DI tractor?
Select one:
a. Worn out primary clutch plate
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 5/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 10
Incorrect
Mark 0.00 out of 1.00
What is the position of control valve after lower link being fully lifted by PC lever?
Select one:
a. Slow drop
b. Fast drop
c. Lift
d. Neutral
Question 11
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement not lifting in MF 241 DI tractor?
Select one:
a. Worn out PTO clutch plate
b. Draft control lever may be below the sector mark Draft
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 6/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 12
Correct
Mark 1.00 out of 1.00
Where will you keep the control levers, while doing internal settings in MARK IA Hydraulic Lift Cover?
Select one:
a. PC- Slow Drop, DC- Sector mark and Lift Arm- Middle position
b. PC- Fast Drop, DC- Below Sector mark and Lift Arm- Fully Up
c. PC- Fast Drop, DC- Sector mark and Lift Arm- Fully down
d. PC- Slow Drop, DC- Above Sector mark and Lift Arm- Fully down
Question 13
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement jerking while lifting?
Select one:
a. Valve chamber outlet valve leakage
b. Worn out control valve
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 7/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 14
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet port open and out port closed
Question 15
Correct
Mark 1.00 out of 1.00
How the “up lift kit” lever is connected to control valve actuating lever in MF 7250?
Select one:
a. Through response linkages
b. Through PC linkages
c. Through DC linkages
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 8/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 16
Incorrect
Mark 0.00 out of 1.00
How many supports are there for hydraulic pump so as to hold it in floating position?
Select one:
a. 4
b. 6
c. 3
d. 5
Question 17
Correct
Mark 1.00 out of 1.00
What could be the one of the cause for fast response is not obtained in MF 1035 DI?
Select one:
a. Draft control lever may be blow the sector mark
b. Excessive gap between the actuating lever and vertical lever
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 9/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 18
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet and outlet ports are open
Question 19
Correct
Mark 1.00 out of 1.00
Hydraulic pump is driven by?
Select one:
a. Main shaft
b. Rear drive shaft
c. Counter shaft
d. PTO shaft
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 10/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 20
Incorrect
Mark 0.00 out of 1.00
Select one:
a. To match the bedding in
b. To mismatch the bedding in
Question 21
Correct
Mark 1.00 out of 1.00
In lift position of the control valve ___________________
Select one:
a. Inlet port closed and outlet port open
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 11/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 22
Incorrect
Mark 0.00 out of 1.00
Select one:
a. 16/53*ERPM
b. 17/52*ERPM
c. 18/50*ERPM
d. 19/61*ERPM
Question 23
Correct
Mark 1.00 out of 1.00
What will be the effect of actuating lever self-locking nut setting is loose?
Select one:
a. Draft sensing may be poor
b. Transport height may not obtained
c. Slow may not obtained
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 12/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 24
Incorrect
Mark 0.00 out of 1.00
Select one:
a. Helps to obtain slow response
b. Tends to bring back the control valve to its natural position
Question 25
Correct
Mark 1.00 out of 1.00
How do you lift the hydraulically operated tipping trailer and how do you stop lifting trailer in MF 1035 DI tractor?
Select one:
a. PC lever – Fully up, DC lever – below sector mark to lift and make manual neutral by PC lever to stop
b. PC lever – Fast or slow, DC lever – Above sector mark to lift and make manual neutral by DC lever to stop
c. PC lever – Fast, DC lever – Sector mark to lift and make manual neutral by DC lever to stop
d. PC lever – Fully up, DC lever – Sector mark to lift and make manual neutral by DC lever to stop
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 13/14
7/19/2021 Assessment_ Module 2_ Hydraulics: Attempt review
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6349&cmid=212 14/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 1
Correct
The lifting capacity on lower links for MF 241 tractor in Horizontal position is ______
Select one:
a. 2050 Kg
b. 1700 Kg
c. 1850 KG
d. 1550 Kg
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 1/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 2
Incorrect
Mark 0.00 out of 1.00
How many supports are there for hydraulic pump so as to hold it in floating position?
Select one:
a. 5
b. 4
c. 3
d. 6
Question 3
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement jerking while lowering?
Select one:
a. Control spring setting is loose
b. Worn out control valve
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 2/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 4
Incorrect
Mark 0.00 out of 1.00
Select one:
a. Transport Lock Valve
b. Relief Valve
Question 5
Incorrect
Mark 0.00 out of 1.00
Select one:
a. 19/61*ERPM
b. 17/52*ERPM
c. 16/53*ERPM
d. 18/50*ERPM
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 3/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 6
Incorrect
Mark 0.00 out of 1.00
How much weight to be added approximately on the lower links before doing the external settings in MARK IA Hydraulics?
Select one:
a. 1100 Kg
b. 850 Kg
c. 1250 Kg
d. 400 Kg
Question 7
Incorrect
Mark 0.00 out of 1.00
Which part is the key to achieve the slow response control of mark 1A hydraulic system?
Select one:
a. Eccentric roller
b. Mango cam
c. Control spring assembly
d. Relief valve
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 4/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 8
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet port open and out port closed
b. Inlet and outlet ports are closed
Question 9
Incorrect
Mark 0.00 out of 1.00
How do you lift the hydraulically operated tipping trailer and how do you stop lifting trailer in MF 1035 DI tractor?
Select one:
a. PC lever – Fast, DC lever – Sector mark to lift and make manual neutral by DC lever to stop
b. PC lever – Fully up, DC lever – Sector mark to lift and make manual neutral by DC lever to stop
c. PC lever – Fast or slow, DC lever – Above sector mark to lift and make manual neutral by DC lever to stop
d. PC lever – Fully up, DC lever – below sector mark to lift and make manual neutral by PC lever to stop
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 5/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 10
Correct
Mark 1.00 out of 1.00
Select one:
Question 11
Correct
Mark 1.00 out of 1.00
Select one:
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 6/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 12
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for slow response not obtained in mark 1A hydraulics tractor?
Select one:
a. Excessive gap between differential cam and eccentric roller
b. No gap between differential cam and eccentric roller
c. Transmission oil level may be low
Question 13
Correct
Mark 1.00 out of 1.00
Select one:
a. Inlet and outlet ports are open
b. Inlet and outlet ports are closed
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 7/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 14
Correct
Mark 1.00 out of 1.00
What will be the effect of actuating lever self-locking nut setting is loose?
Select one:
Question 15
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for tipping trailer not lifting by DC lever in MF 1035 DI tractor?
Select one:
a. Response control setting may be wrong
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 8/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 16
Correct
Mark 1.00 out of 1.00
What is the position of control valve when the PC lever is moved to up position and lower link is started raising?
Select one:
a. Lift
b. Neutral
c. Fast drop
d. Slow drop
Question 17
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for implement jerking after fully lifted?
Select one:
a. Strainer choked
b. Control spring setting is loose
c. Valve chamber outlet valve leakage
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 9/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 18
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for low depth of cut in mould board plough operation with MF 1035 DI tractor?
Select one:
a. Eccentric roller setting may be wrong
b. Draft control setting guide rod nut may be over tighten
Question 19
Correct
Mark 1.00 out of 1.00
Which part is the key to achieve the draft control of hydraulic system?
Select one:
a. Eccentric roller
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 10/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 20
Incorrect
Mark 0.00 out of 1.00
Select one:
a. Counter shaft
b. Main shaft
Question 21
Incorrect
Mark 0.00 out of 1.00
Select one:
a. Inlet port open and out port closed
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 11/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 22
Incorrect
Mark 0.00 out of 1.00
Select one:
a. Neutral
b. Lift
c. Up
d. Drop
Question 23
Incorrect
Mark 0.00 out of 1.00
What could be the one of the cause for fast response is not obtained in MF 1035 DI?
Select one:
a. Transport lock valve may be partially closed
b. Draft control lever may be blow the sector mark
c. Control spring setting may be loose
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 12/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
Question 24
Correct
Mark 1.00 out of 1.00
Select one:
Question 25
Incorrect
Mark 0.00 out of 1.00
How the “up lift kit” lever is connected to control valve actuating lever in MF 7250?
Select one:
a. Through PC linkages
b. Through external cable and cam
c. Through response linkages
d. Through DC linkages
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 13/14
19/07/2021 Assessment_ Module 2_ Hydraulics: Attempt review
https://tafelearningcentre.com/mod/quiz/review.php?attempt=6339&cmid=212 14/14