Professional Documents
Culture Documents
Description:
Parker Rocksledger primary
roller bearing jaw crushers are
of the single toggle down-
thrust type. They are designed
to crush the toughest
materials and experience in
hundreds of installations
demonstrates their efficiency
and reliability.
Rocksledgers are
available in 4 sizes: Jawstock: protected against the entrance
900mm x 600mm Strongly constructed from cast of grit and dirt by recharge-
1100mm x 650mm steel with deep webbing to able grease filled labyrinth
1100mm x 800mm give great strength with seals.
1300mm x 1050mm reasonable lightness. The body bearings are
mounted in taper withdrawal
The Body: Flywheels: sleeves and within separate
This is an all-welded steel Interchangeable large cartridge type housing, which
fabrication with these diameter flywheels are fitted. incorporates grease valves to
features: One is grooved for V-rope prevent over-greasing the
drive. bearings.
• Single plate wall with
external side stiffening webs
• Machined on the groove Changing Jaw Settings: Toggle Plate
block seating and bored to Adjustment to jaw settings is & Groove Block:
accept the side bearings carried out by adding or The toggle plate is a high
• The steel housing for removing shim plates of quality iron casting with the
supporting the side bearings varying thickness’ behind the ends machined to a segment
are welded into the body groove block, which is of a circle to minimise rubbing
• The top caps over the side adjusted by a hydraulic ram and reduce wear.
bearings are easily removed with hand-operation pump.
to enable the jawstock with
shaft assembly to be lifted Crushing Chamber:
out complete
Jaw Stock & The fixing and swing jaws are
Body Bearings: toothed sectional manganese
Self-aligning spherical roller steel castings. Lining the
Eccentric Shaft: chamber sides are renewable
High quality forged steel bearings are fitted. They are
shaft, fully machined. grease-lubricated and manganese steel wearing
plates.
ROCKSLEDGER
TECHNICAL DATA
SIZE OF CRUSHER MAX FEED SIZE JAW SETTING APPROXIMATE NO & SIZE OF POWER TO DRIVE
mm x mm mm Max mm Min mm WEIGHT kg VEE ROPE kW
900 x 600 575 200 50 15000 6 SPC 90
1100 x 630 605 175 50 18000 8 SPC 110
1100 x 650 625 175 65 18000 8 SPC 110
1100 x 760 720 200 75 26945 8 SPC 110
1100 x 800 760 200 100 26945 8 SPC 110
1300 x 1050 1000 320 150 38000 12 SPC 200
NOTE:
Capacities quoted are intended as a guideline only, and are based on a clean, dry graded continuous
feed material (weighing 1600kg/m³ (100lb/ft³) and a S.G. of 2.7 average), which will readily enter the
crusher feed opening without obstruction, with 100% greater than the jaw setting and 25% less than
twice the jaw setting.
Actual capacities can vary considerably from those given, due to the following application and
operational factors:
1. MATERIAL – Friability & Toughness.
2. FEED CONDITIONS – Grading of feed size (compliance with Euro STD). Presence of clay or sticky
material. Moisture content.
3. INSTALLATION – Method of Feeding. Removal of undersize.
Operation at settings outside those stated should be referred to the Works.
All reasonable steps have been taken to ensure the accuracy of this publication. However, due to
continuous development of the products, Parker Plant Limited, reserve the right to change details
without notice. All machines supplied in accordance with our standard conditions. Illustrations may
show optional equipment.
Parker Plant Limited, P O Box 146, Canon Street, Leicester, LE4 6HD, England
Tel: +44 (0)116 266 5999 Sales Fax: +44 (0)116 261 0812
E-Mail: sales@parkerplant.com
Website: http://www.parkerplant.com
© Parker Plant Ltd 2001