Professional Documents
Culture Documents
Autodesk Inventor
Descrição de Comandos
ÍNDICE
1 -
O que é o Autodesk Inventor......................................................................................... 1
2 -
Interface – Ambiente de Trabalho ................................................................................ 1
3 -
Tipos de Documentos .................................................................................................... 3
4 -
Sketch............................................................................................................................ 3
4.1 - Line ......................................................................................................................... 3
4.2 - Spline ...................................................................................................................... 4
4.3 - Circle ....................................................................................................................... 6
4.4 - Elipse....................................................................................................................... 6
4.5 - Arc .......................................................................................................................... 6
4.6 - Rectangle ................................................................................................................. 7
4.7 - Fillet ........................................................................................................................ 7
4.8 - Chamfer ................................................................................................................... 8
4.9 - Point, Hole Center ..................................................................................................... 9
4.10 - Polygon.................................................................................................................... 9
4.11 - Mirror...................................................................................................................... 10
4.12 - Rectangular Pattern.................................................................................................. 10
4.13 - Circular Pattern ........................................................................................................ 11
4.14 - Offset ..................................................................................................................... 12
4.15 - General Dimension ................................................................................................... 12
4.16 - Auto Dimension ....................................................................................................... 14
4.17 - Extend .................................................................................................................... 14
4.18 - Trim........................................................................................................................ 14
4.19 - Move ...................................................................................................................... 15
4.20 - Rotate..................................................................................................................... 15
4.21 - Perpencidular........................................................................................................... 15
4.22 - Parallel.................................................................................................................... 16
4.23 - Tangent .................................................................................................................. 16
4.24 - Coincident ............................................................................................................... 16
4.25 - Concentric ............................................................................................................... 16
4.26 - Colinear .................................................................................................................. 17
4.27 - Horizontal................................................................................................................ 17
4.28 - Vertical ................................................................................................................... 17
4.29 - Equal ...................................................................................................................... 17
4.30 - Fix .......................................................................................................................... 17
4.31 - Symmetric ............................................................................................................... 18
4.32 - Show Constraints ..................................................................................................... 18
4.33 - Project Geometry ..................................................................................................... 18
4.34 - Parameters.............................................................................................................. 18
4.35 - AutoCAD Insert File .................................................................................................. 20
4.36 - Text........................................................................................................................ 20
4.37 - Insert Image ........................................................................................................... 23
4.38 - Edit Coordinate System............................................................................................. 23
5 - Features........................................................................................................................ 23
5.1 - Extrude ................................................................................................................... 23
5.2 - Revolve ................................................................................................................... 26
5.3 - Hole........................................................................................................................ 28
5.4 - Shell ....................................................................................................................... 33
5.5 - Rib.......................................................................................................................... 34
5.6 - Loft......................................................................................................................... 36
5.7 - Sweep..................................................................................................................... 38
5.8 - Coil ......................................................................................................................... 39
www.mapdata.com.br
Autodesk Inventor Descrição de Comandos
www.mapdata.com.br
Autodesk Inventor Descrição de Comandos
6.2.22 -
Hole Table – View....................................................................................... 138
6.2.23 -
Selected Type............................................................................................. 141
6.2.24 -
Caterpillar .................................................................................................. 144
6.2.25 -
End Treatment ........................................................................................... 146
6.2.26 -
Revision Table ............................................................................................ 147
6.2.27 -
Revision Tag .............................................................................................. 149
6.2.28 -
Symbols..................................................................................................... 150
6.2.29 -
Retrieve Dimensions ................................................................................... 150
6.3 - Browser Bar ............................................................................................................ 151
6.3.1 - Sheet Formats.............................................................................................. 153
6.3.2 - Borders........................................................................................................ 154
6.3.3 - Title Blocks .................................................................................................. 158
6.3.4 - Sketched Symbols ........................................................................................ 160
7 - Assembly ..................................................................................................................... 162
7.1 - Place Component .................................................................................................... 162
7.2 - Create Component .................................................................................................. 162
7.3 - Pattern Component ................................................................................................. 162
7.4 - Rectangular Pattern................................................................................................. 163
7.5 - Circular Pattern ....................................................................................................... 163
7.6 - Mirror Component ................................................................................................... 164
7.7 - Copy Component .................................................................................................... 165
7.8 - Place Constraints..................................................................................................... 166
7.9 - Replace Component ................................................................................................ 168
7.10 - Replace All Components .......................................................................................... 168
7.11 - Move Component .................................................................................................... 168
7.12 - Rotate Component .................................................................................................. 168
7.13 - Quarter Section View............................................................................................... 168
7.14 - Half Section View .................................................................................................... 169
7.15 - Three-Quarter Section View ..................................................................................... 169
7.16 - End Section View .................................................................................................... 169
8 - Configurações (Application Options) .......................................................................... 169
8.1 - General .................................................................................................................. 169
8.2 - Files....................................................................................................................... 171
8.3 - Colors .................................................................................................................... 172
8.4 - Display................................................................................................................... 173
8.5 - Hardware ............................................................................................................... 179
8.6 - Prompts ................................................................................................................. 180
8.7 - Notebook ............................................................................................................... 181
8.8 - Sketch.................................................................................................................... 182
8.9 - Part ....................................................................................................................... 186
8.10 - iFeature ................................................................................................................. 187
8.11 - Assembly................................................................................................................ 188
www.mapdata.com.br