Professional Documents
Culture Documents
SPECIFICATION
FOR
600/1000 V RATING
TABLE OF CONTENTS
1.0 SCOPE
4.1 General
4.2 Ratings
4.3 Materials
4.4 Cable Marking and Identification
5.0 TESTS
This SMSS shall also be read in conjunction with SCECO-East Purchase Order or
Contract Schedules for project, as applicable.
The latest revision of the following Codes and Standards shall be applicable for the
equipment/material covered in this SMSS. In case of conflict, the
vendor/manufacturer may propose equipment/material conforming to one group of
Industry Codes and Standards quoted hereunder without jeopardizing the requirements
of this SMSS.
3.2 IEC 502 Extruded Solid Dielectric Insulated Power Cables for
Rated Voltages from 1 kV up to 30 kV
3.5 ASTM B-33 Tinned Soft or Annealed Copper Wire for Electrical
Purposes
4.1 General
4.1.1 The cable shall meet or exceed the requirements of this Specification in
all respects.
4.1.2 The cable shall be designed for use in all low voltage power and/or
control circuits and for installation in conduits, underground ducts or
cable trays/raceways or for directly buried installations.
4.2 Ratings
4.3.1 Conductor
4.3.2 Insulation
4.3.3 Separator
When required, the separator shall be a mylar tape, PVC binder tape or
extruded PVC layer applied over the assembled cores.
When required, the metallic shield shall be a helically applied flat bare
copper tape.
4.3.5 Armor
b. When specified and for direct burial, the cable armor shall consist
of close-fitting flexible corrugated impervious galvanized steel
interlocked sheath.
Table I
4.3.6 Jacket
The jacket shall be black, extruded PVC with heat, moisture, oil,
sunlight, acid, alkali and flame resistant properties. For flame
retardancy, a minimum oxygen index level of 30 is required.
4.4.1 The outer surface of the cable shall be durably marked in English
language and Arabic numerals at intervals of 1 m with the following
minimum information:
a. Rated voltage
b. Insulation Material
e. Year of manufacture
The marking shall start at a distance of 50 cm from the inner end of the
cable.
4.4.2 The jacket of all cables, excluding building wires, shall be marked with
the cumulative length at every one meter, with the highest length mark
on the outer end of the cable.
The length marking shall start at one meter distance from the inner end
of the cable, so that it will not coincide with the markings described in
subclause 4.4.1.
4.4.5 For systems with ground or neutral application, the black color shall
indicate the neutral conductor.
5.0 TESTS
All test results shall be provided for review and acceptance by SCECO-East.
All type (design) tests prescribed in the IEC 502 or ICEA T-27-581 (NEMA
WC 53) shall be performed on a representative unit or on the first unit of every
new design or rating to be supplied to SCECO-East.
In lieu of the actual type (design) tests, certified test reports of type (deisgn)
tests performed on an identical unit may be Submitted to SCECO-East for
review and approval during bidding stage.
In addition to the applicable items of 01-SMSS-01, the following packing and shipping
instructions are applicable.
6.1 The cable shall be delivered without splices on nonreturnable standard size
reels properly packed and lagged externally to provide physical protection for
the cable shipment and to facilitate field handling and long term storage.
Wood lagging shall have a minimum thickness of 25 mm.
6.2 The cable ends shall be sealed with a waterproof, heat shrinkable plastic or
elastomeric end cap with adhesive type sealing compound. Cable ends shall be
properly secured to the reel.
6.3.1 Cable reels/drums shall be marked in legible and indelible letters giving
the following particulars:
REFERENCE
SECTION NO. DESCRIPTION A B C
4.1 General
REFERENCE
SECTION NO. DESCRIPTION A B C
4.2 Ratings
REFERENCE
SECTION NO. DESCRIPTION A B C
Diameter of compacted
strand (mm)
Number of Conductors
REFERENCE
SECTION NO. DESCRIPTION A B C
REFERENCE
SECTION NO. DESCRIPTION A B C
Manufacturer Vendor/Supplier/
of Material/Equipment Contractor
Name of Company
Official Seal/Stamp
of the Company