Professional Documents
Culture Documents
FEM in Segmental Analysis
FEM in Segmental Analysis
e-mail: rombach@tu-harburg.de
1 Introduction
Bridges have been built since thousands of years. Nevertheless new innovative
construction methods are still required. Precast concrete segmental hollow box girder
bridges externally prestressed are one of the major new developments in bridge
construction in the last years resulting from the demand for economical design, high
durability and fast and versatile construction. The great advantages has made them the
preferred structure for many great elevated highways, especially in South East Asia. In
contrast to classical monolithic structures a segmental bridge consists of “small”
pieces stressed together by external tendons (fig. 1,2).
Due to the unreinforced joints the deformation characteristics and the load bearing
capacity of a segmental bridge is different from a monolithic construction. In recent
years great effort have been made to improve the knowledge of such structures. There
are still some areas requiring further investigation like e.g. the behavior of the “dry”
joints between the segments. The design of the joints is of critical importance
regarding the safety of segmental bridges. Numerical as well as experimental
investigations regarding the joint behavior will be presented in this paper. Before
discussing this important detail the principal behavior of a single span segmental
bridge is demonstrated by a finite element simulation of a full scale experiment.
1
G.A. Rombach, A. Specker
10.20 m
22.5
40
20
Detail A
240
35 Standard Segment
18
50 2.0 m 75 3.70 m
Shear Keys
Various contact algorithms and contact elements had been studied. The real joint can
only transfer normal and shear forces under compression. As the normal stress
becomes positive e.g. due to bending, the joint opens resp. contact is broken and no
force is transmitted. Sliding occurs when the maximum shear force is exceeded.
Comparative calculations showed that a linear Coulomb friction model is sufficient to
model the real behavior.
2
EM 2000: Finite Element Analysis of Externally Prestressed Segmental Bridges
45 m
45 m
Further simplifications are justified [2]. The deformation characteristics and bearing
capacity of segmental structures are dominated by the behavior of the joints. Therefore
a simple non-linear stress-strain relationship is used for concrete according to EC 2 [3]
and an ideal elastic - ideal plastic model for the tendons.
The single span bridge shown above was chosen because experimental data from a
full-scale test carried out in Bangkok in 1990 [4] is available to verify the numerical
model. In the test the structure was loaded by steel plates up to failure. The results of
the comparison calculations are shown in figure 4, where the mid-span moment is
plotted versus the mid-span deflection. A very good agreement between the numerical
results and the test data can be seen. This proves the statement of the joints mainly
influencing the behavior of segmental structures.
0
Deflection in Mid-Span [mm]
100 Mid-Span
200
300
Test Results
Numerical Results
400
0 10 20 30 40 50 60
Mid-Span Moment [MNm]
The principal behavior of a segmental bridge under normal bending can be described
as follows. As long as the structure is under full compression a segmental bridge
behaves linear elastic like a monolithic one. When loading resp. the bending moment
is increased, joints start to open and the deflections exhibit a non-linear growth as the
overall stiffness decreases. Within a small increase of loading the joints at mid-span
open up to the top slab. Then deflections rise again proportionally to the applied load
until failure as the lever arm of the internal forces is nearly constant. Failure occurred
usually when tendons start to yield and the neutral axis is shifted into the top slab
causing the concrete to crush.
3
G.A. Rombach, A. Specker
As long as the joint is under compression, the segmental bridge behaves like a
monolithic one despite of local effects of the joint and the shear keys. When the joint
opens the area to transfer shear loads becomes smaller whereby the normal and shear
stresses at the top slab increases (figure 8).
Figure 8 shows the normal and shear stress distribution in the webs when the joint is
closed and when it is open up to appr. half of the height of the section. It can be seen
that shear forces are mainly transmitted in the compression zone. Only a few shear
keys are able to transfer shear loads across an opened joint (figure 7,8).
4
EM 2000: Finite Element Analysis of Externally Prestressed Segmental Bridges
σ joint open
2.40m
σ joint closed
τ joint open
Joint
τ joint closed
τ [N/mm²]
6 4 2 0
Fig. 8 Normal and shear stress distribution in the closed and opened joint
These results demonstrate that the indentation of the joints can be neglected in
numerical calculations. It should be noted that this is only the case if the structure is
under pure bending. When the bridge is un-symmetric loaded resulting in torsion
moments the shear keys have to be modeled as other studies showed.
3 Segmental Joints
One of the major areas of uncertainty is the load bearing capacity of the unreinforced
joints between the segments. Design and construction of the joints are of critical
importance regarding the safety of segmental bridges. The models used in practical
design are gained from experiments which are described by simple analytical formulae
[5]. Due to the fine indentation of the joints and the complicated interaction between
the rough concrete surfaces measurements can hardly be carried out. Numerical
calculations are required to investigate the load bearing capacity of the joints [6].
5
G.A. Rombach, A. Specker
300 mm
Joint
400 mm
Fig. 9 Test specimen Fig. 10 Crack pattern before failure
The finite element analysis considers the non-linear behavior of concrete incl.
cracking resp. crushing and the interaction between the surfaces (friction, bond,
slippage). The specimen is first stressed normal to the joint and then loaded vertically
up to failure.
Results are shown in figure 11. Numerical and test data show an overall good
agreement. Using dry joints there is slippage in the first part of the test because the
specimen were not match-cast. This is not considered in the numerical model.
250 300
Epoxy Joint
Dry Joint 250
200 ts
sul
Re
al
200 eric
Applied Load [kN]
m t
lts Nu Tes
Applied Load [kN]
150 su
Re
ical
r 150
me
Nu
100
100
st
Te
50
50
0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70 0.00 0.10 0.20 0.30 0.40 0.50 0.60 0.70
Fig. 11 Test results versus numerical results for dry and epoxy glued joint
6
EM 2000: Finite Element Analysis of Externally Prestressed Segmental Bridges
80 30
60
53.7 4 Shear Keys 20
Applied Load [kN/cm]
50 [5]
TO failure line
SH lts
40 40.7 3 Shear Keys 15 AA esu
ical R
r
me
30 Nu
26.8 2 Shear Keys 10
6]
20 V[
DB
13.6 1 Shear Key 5
10
0.00 0.10 0.20 0.30 0.40 0.00 10.00 20.00 30.00 40.00
Deflection [mm]
4 Conclusions
Non-linear finite element models are presented and discussed to study the behaviour
of real segmental box girder bridges. The results show that the behaviour of such type
of structure is dominated by the un-reinforced joints. The indentation of the shear keys
can be neglected in the numerical model if the structure is loaded by bending only.
Numerical and experimental investigations of the bearing capacity of the joints show
that some analytical design models overestimates the capacity. The objective of the
ongoing investigations is to evaluate a simple design model for practical use.
5 References
[1] G. Rombach: Segmental box girder bridges with external prestressing.
Conference „Actual Problems in Civil Engineering“ . St. Petersburg, Juli1997
[2] G. Rombach, A: Specker: Numerical modelling of segmental bridges.
European Conference on Computational Mechanics, Munich, August 1999
[3] Eurocode 2, Part 1. Design of concrete structures. 1992
[4] T. Takebayashi, K. Deeprasertwong, Y. Leung: A full-scale destructive test of
a precast segmental box girder bridge with dry joints an external tendons,
Proceedings of the Institution of Civil Engineers, August 1994, pp. 297-315
[5] AASHTO. Guide specification for the design and construction of segmental
concrete bridges. 1998
[6] G. Rombach, A. Specker: Design of segmental joints, in: Externe Vorspannung
und Segmentbauweise, Ernst & Sohn, 1998, pp. 303-313
[7] Bakhoum M.M., Buyukozturk, O., Beattie S.M.: Structural Performance of
Joints in Precast Concrete Segmental Bridges. MIT Research Report No. R89-
26, Massachusetts Institute of Technology, November 1989
[8] Deutscher Beton-Verein: Empfehlungen für Segmentfertigteilbrücken mit
externen Spanngliedern. April 1998