Professional Documents
Culture Documents
Asme b107.2
Asme b107.2
~
~ Mechanical Engineers
The American Society of
SOCKET WRENCHES,
EXTENSIONS, ADAPTORS,
AND UNIVERSAL JOINTS, ·.
POWER DRIVE (IMPACTI
ONCH SERIES)
ASME Bl 07.2-2002
(Revision of ASME B107.2-1995)
Ucenst:1d to JBS}'M'dl Hooker. ANSI order X 429079. Dov·Jn!oadeu 2/'18/2010 12:4? Pfvi Singie user hci:~nse or.!y. Copying t'md nt~tw(1rking prohibited.
This Standard will be revised when the Society approves the issuance of a
new edition. There will be no addenda issued to this edition.
This code or standard was developed under procedures accredited as meeting the criteria for
American National Standards. The Standards Committee that approved the code or standard
was balanced to assure that individuals from competent and concerned interests have had an
opportunity to participate. The proposed code or standard was made available for public review
and comment that provides an opportunity for additional publ ic input from industry, academia,
regulatory agencies, and the public-at-large.
ASME does not "approve, " "rate," or " endorse " any item, construction, proprietary device,
or activity.
ASME does not take any position with respect to the validity of any patent rights asserted in
connection with any items mentioned in this document, and does not undertake to insure anyone
utilizing a standard against liability for infringement of any applicable letters patent, nor assumes
any such liability. Users of a code or standard are expressly advised that determination of the
validity of any such patent rights, and the risk of infringement of such rights, is entirely their
own responsibility.
Participation by federal agency representative(s) or person(s) affiliated with industry is not to
be interpreted as government or industry endorsement of this code or standard .
ASME accepts responsibility for only those interpretations of this document issued in
accordance with the established ASME procedures and policies, which precludes the issuance
of interpretations by individuals.
Copyright © 2003 by
THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS
All Rights Reserved
Printed in U.S.A.
CONTENTS
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Committee Roster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi
Correspondence With the B 107 Committee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2 Classification .... . ............... .. ........ . ....... .. .......... . . ... . ... .. . . ... .
3 Normative References . ..... . ..... . .. . ....... .. .... . ..... .. ................... .
4 Requirements ........ . . .. .. . . ........ ... .... ... . . .. . ..... . .............. . ..... .
5 Test Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6 Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figures
1 Type I, II, and VII Sockets, Class 1, Regular Length; Class 2, Long Length . . . . . . . 3
2 Type III, Universal Sockets, Single Hexagon (6-Point) and Double Hexagon
(12-Point) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Type IV Bar, Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4 Type V, Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
5 Type VI, Universal Joint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Tables
1 Type I, Class 1 and 2, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular and Long Length, 1/ 4 in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Type I, Class 1, 2, and 3, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular, Long, and Extra Long Length, 3/ 8 in. Drive . . . . . . . . . . . . . . . . . 5
3 Type I, Class 1, 2, and 3, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular, Long, and Extra Long Length, 1/ 2 in. Drive . . . . . . . . . . . . . . . . . 6
4 Type I, Class 1 and 2, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular and Long Length, 3/ 4 in. Drive .. .. . . .. .. .. .. .. .. .. .. .. .. .. .. 7
5 Type I, Class 4 and 5, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular and Long Length, Thin Wall, 1/ 2 in. Drive . . . . . . . . . . . . . . . . . . . 8
6 Type I, Class 4, Single Hexagon (6-Point) and Double Hexagon (12-Point),
Regular Length, Thin Wall, 3/ 4 in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7 Type I, Class 1 and 2, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular and Long Length, 1 in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
8 Type VII, Class 1 and 2, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular and Long Length, #5 Spline Drive . . . . . . . . . . . . . . . . . . . . . . . . . . 11
9 Type I, Class 1 and 2, Single Hexagon (6-Point) and Double Hexagon
(12-Point), Regular and Long Length, 11/ 2 in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
10 Type I, Class 1, Single Hexagon (6-Point), Regular Length, 2 1/ 2 in. Drive . . . . . . . . . . 13
11 Type II, Class l and 2, Single Square (4-Point) and Double Square (8-Point),
Regular and Long Length, 3/s in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
iii
12 Type II, Class 1 and 2, Single Square (4-Point) and Double Square (8-Point),
Regular and Long Length, 1/ 2 in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
13 Type II, Class 1 and 2, Single Square (4-Point) and Double Square (8-Point),
Regular and Long Length, 3/ 4 in. Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
14 Type III, Class 1 and 2, Universal, Single Hexagon (6-Point) and Double
Hexagon (12-Point), Regular and Long Length, 3/s in. Drive . . . . . . . . . . . . . . . . . . . . . 15
15 Type III, Class 1 and 2, Universal, Single Hexagon (6-Point) and Double
Hexagon (12-Point), Regular and Long Length, 1/ 2 in. Drive . . . . . . . . . . . . . . . . . . . . . 16
16 Type IV, Bar, Extension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
17 Type V, Adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
18 Type VI, Universal Joint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
19 Hexagon Mandrel Dimensions and Maximum Depth of Mandrel Insertion . . . . . . . . . . . 17
20 Square Mandrel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
iv
FOREWORD
The American National Standards Committee B107, Socket Wrenches and Drives, under
sponsorship of The American Society of Mechanical Engineers (ASME), was reorganized
as an ASME Standards Committee, and its title was changed to Hand Tools and Accessories.
The purposes of this Standard are to define general and dimensional data specifically
applicable to detachable socket wrenches and to specify test methods to evaluate performance
relating to the defined requirements.
This Standard is a revision of B107.2-1995 Socket Wrenches, Extensions, Adaptors, and
Universal Joints, Power Drive (Impact) (Inch Series). A principal change in this edition of
the Standard is the use of Type and Class designations in place of Class and Style designations,
in accordance with other B107 Standards. Updated references, finish requirements, and
dimensional data are included.
The format of this Standard is in accordance with The ASME Codes & Standards Writing
Guide 2000. Requests for interpretations of the technical requirements of this Standard
should be expressed in writing to the Secretary, B107 Committee, at the address below.
Suggestions for the improvement of this Standard are welcome. They should be addressed
to the The American Society of Mechanical Engineers, Secretary, B 107 Standards Committee,
Three Park Avenue, New York, NY 10016-5990.
The requirements of this Standard become effective at the time of publication. This
revision was approved as an American National Standard on May 13, 2002.
(The following is the roster of the Committee at the time of approval of this Standard.)
OFFICERS
R. R. McCullough, Chair
G. E. Olson, Vice Chair
J. R. Bird, Secretary
COMMITTEE PERSONNEL
J. R. Bird, The American Society of Mechanical Engineers
J. D. Davidson, Sears Roebuck and Co.
J. S. Foote, Trade Association Management, Inc.
A. Herskovitz, Consultant
H. Kimball, Naval Air Warfare Center
R. R. McCullough, Consultant
D. S. McKittrick, Western Forge
G. E. Olson, Gene Olson Engineering Consultant, ltd.
W. T. Pagac, Snap-on, Inc.
D. M. Eggert, Alternate, Snap-on, Inc.
J. M. Ster, General Services Administration
I. I. Harding, Alternate, General Services Administration
R. B. Wright, Wright Tool Co.
W. C. Snyder, Alternate, Wright Tool Co.
vi
General. ASME Standards are developed and maintained with the intent to represent the
consensus of concerned interests. As such, users of this Standard may interact with the
Committee by requesting interpretations, proposing revisions, and attending Committee
meetings. Correspondence should be addressed to:
Secretary, B107 Standards Committee
The American Society of Mechanical Engineers
Three Park A venue
New York, NY 10016-5990
vii
viii
ASME B107.2-2002
I
---1-------r-
T ~-
GENERAL NOTES:
(a) A shall be equal to or greater than nut opening depth in applicable tables.
(b) Maximum nut end diameter of socket C shall not be exceeded for length B and shall conform to applicable tables.
(c) B length shall be greater than or equal to the minimum nut opening depth A in applicable tables.
Shape optional
ID
L'---'
--1--A1t
;- t
ID
r-
---- : -
I
C
GENERAL NOTES:
(a) A shall be equal to or greater than nut opening depth in applicable tables.
(b) Maximum nut end diameter of socket C shall not be exceeded for length B and shall conform to applicable tables.
(c) 8 length shall be greater than or equal to the minimum nut opening depth A in applicable tables.
(d) D is the outside diameter, drive end, and shall conform to applicable tables.
TABLE 1 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, %in . DRIVE
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, A E lbf-in.,
Opening, in. Max. Min. Min. Max. Min . Max. in ., Min. in., Min. Min.
TABLE 2 TYPE I, CLASS 1, 2 AND 3, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR, LONG, AND EXTRA LONG LENGTH, % in. DRIVE
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Opening Hole Proof
Nut End, Drive End,
Long C D Depth, Diameter, Torque,
Nominal Regular, Extra Long, A E lbf-in.,
Opening, in. Max. Min. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
s/1s 1.187 1.688 2.500 0.471 0.515 0.677 0.760 0.102 0.171 440
1%2 1.187 1.688 2.500 0.490 0.552 0.677 0.760 0.117 0.203 550
%
7
1.187 1.688 2.500 2.688 0.527 0.605 0.677 0.760 0.117 0.281 660
/1s 1.187 1.688 2.500 2.688 0.613 0.697 0.677 0.760 0.203 0.281 930
% 1.187 1.688 2.500 2.688 0.693 0.823 0.700 0.823 0.209 0.344 1240
s/1s 1.250 1.938 2.750 3.250 0.771 0.885 0.771 0.885 0.249 0.406 1600
% 1.250 1.938 2.750 0.860 0.948 0.860 0.948 0.281 0.469 2000
11;1s 1.250 1.938 2.750 0.860 1.031 0.865 1.031 0.318 0.469 2200
% 1.250 1.938 2.750 1.021 1.073 0.865 1.073 0.356 0.531 2200
4.15 Type II - Sockets, Single Square (4- JOmts shall be provided with a friction type tension
Point) and Double Square (8-Point) device which will hold the drive end and socket or
tang end in any set position with a force adequate to
Sockets shall be similar to Fig. 1 and shall conform
hold the socket against gravity. The tension device
to Tables 11, 12, and 13.
shall compensate for wear. Universal sockets and univer-
sal joints shall be capable of rotation in a complete
4.16 Type Ill - Universal Sockets, Single
revolution when the angular deviation of one member
Hexagon (6-Point) and Double Hexagon
from the common centerline is 20 deg minimum and
(12-Point) and Type VI - Universal
35 deg maximum. Type III universal sockets shall be
Joints
similar to Fig. 2 and shall conform to Tables 14 and
Universal sockets shall be a single hexagon (6-point) 15 for the size and drive specified. Type VI universal
or double hexagon (12-point) as specified. The 3/s in. joints shall be similar to Fig. 5 and shall conform to
and 1/ 2 in. drive size universal sockets and universal Table 18 for the drive specified.
TABLE 3 TYPE I, CLASS 1, ·2 AND 3, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR, LONG, AND EXTRA LONG LENGTH, 1/i in. DRIVE
%
7
1.800 3.187 3.688 0.550 0.715 0.850 1.135 0.117 0.281 1100
/,s 1.800 3.187 3.688 0.638 0.806 0.850 1.135 0.203 0.281 1500
112 1.800 3.187 3.688 4.938 0.726 0.897 0.850 1.135 0.209 0.344 2000
9;,s 1.800 3.187 3.688 4.938 0.814 0.987 0.850 1.135 0.249 0.406 2600
% 1.800 3.187 3.688 4.938 0.902 1.070 0.850 1.135 0.281 0.469 3300
11;,s 1.800 3.187 3.688 4.938 0.990 1.169 0.990 1.197 0.318 0.469 4100
%
13
1.800 3.187 3.688 4.938 1.062 1.260 1.004 1.260 0.356 0.531 5000
116 1.812 3.187 3.688 4.938 1.135 1.325 1.019 1.335 0.418 0.594 5000
71a 1.960 3.187 3.688 4.938 1.207 1.390 1.033 1.410 0.479 0.594 5000
15; 2.1 00 3.187 3.688 4.938 1.280 1.455 1.048 1.485 0.490 0.656 5000
16
1 2.100 3.187 3.688 4.938 1.352 1.521 1.062 1.560 0.490 0.656 5000
11!,s 2.410 3.187 3.688 4.938 1.425 1.586 1.077 1.635 0.490 0.687 5000
1% 2.410 3.187 3.688 4.938 1.497 1.651 1.091 1.710 0.632 0.781 5000
1% 2.410 3.187 3.688 1.642 1.781 1.120 1.860 0.632 0.812 5000
15/,s 2.500 3.187 3.688 1.789 2.197 1.120 1.906 0.748 0.906 5000
1% 2.500 3.187 3.688 1.861 2.197 1.120 1.906 0.748 0.937 5000
17/,s 2.500 3.187 3.688 1.933 2.322 1.120 2.031 0.748 1.000 5000
11/i 2.500 3.1 87 3.688 2.005 2.387 1.120 2.156 0.847 1.062 5000
19/,s 2.500 3.187 3.688 2.075 2.445 1.120 2.250 0.847 1.062 5000
4.17 Type IV - Extension Bars penetrator and employing a 150 kg major load in
accordance with ASTM E 18. When surface preparation
Extension bars shall have an external square drive
is necessary, the amount of material removed in the
at one end and an internal square drive of the same
area contacted by the indicator shall not exceed:
size at the other end. The extension bar shall be similar
to Fig. 3 and shall conform to the dimensions in
Drive Size,
Table 16. in. Max. Material Removed
TABLE 4 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH,% in. DRIVE
5.2.1 Sockets. A square test plug of suitable universal socket assembly in the axis about which the
strength and complying with the dimensional require- load is applied.
ments of the drive tang specified in ASME B107.4M
shall be employed. The test plug may be driven by 5.2.3 Extension. Tests shall be made in the same
any suitable manual or mechanical means. The socket manner as specified in para. 5 .2.1 except that the
shall then be engaged on the end of a mandrel to external drive tang shall be inserted in an internal
maximum mandrel depth in accordance with Tables 19 socket and secured in a mandrel.
and 20. Means shall be provided at the outer end of
the test plug to prevent slippage of the socket end- 5.3 Mandrels for Wrench Openings
wise from the mandrel and to keep the test pieces in
alignment. Sockets shall be tested on mandrels. Single hexagon
(6-point) or double hexagon (12-point) sockets or uni-
5.2.2 Universal Sockets. Tests shall be made in versal sockets shall be tested on hexagonal mandrels
the same manner as specified in para. 5.2.1 except that conforming to Table 19. Single square (4-point) or
means shall be provided to keep the parts of the double square (8-point) sockets shall be tested on square
TABLE 5 TYPE I, CLASS 4 AND 5, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, THIN WALL, 1/z in. DRIVE
11;16 2.000 3.187 0.944 1.024 0.964 1.197 0.318 0.469 4100
% 2.000 3.187 1.020 1.100 1.004 1.260 0.356 0.531 5000
13;16 2.000 3.187 1.098 1.1 58 1.019 1.335 0.418 0.594 5000
71a
1s
2.000 3.187 1.175 1.255 1.033 1.410 0.479 0.594 5000
116 2.000 3.187 1.253 1.333 1.048 1.485 0.490 0.656 6000
1s/15 2.500 3.187 1.718 1.798 1.120 1.860 0.748 0.906 5000
1% 2.500 3.187 1.795 1.875 1.120 1.860 0.748 0.937 5000
17/16 2.500 3.187 1.872 1.952 1.120 2.000 0.748 1.000 5000
11/2 2. 500 3.187 1.950 2.030 1.120 2.000 0.847 1.062 5000
19/16 2.500 3.187 2.028 2.108 1.120 2.000 0.847 1.062 5000
TABLE 7 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, 1 in. DRIVE
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, A E lbf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
10
TABLE 8 TYPE VII, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, #5 SPLINE DRIVE
Outside Diameter, in.
Nut Bolt Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, A E lbf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
11/,s 2.687 2.937 1.521 1.763 2.365 2.406 0.490 0.687 11,700
11/s 2.687 2.937 1.552 1.823 2.365 2.406 0.632 0.781 12,800
1% 2.750 2.937 1.736 2.197 2.365 2.406 0.632 0.812 15,400
1s/,s 2.875 3.187 1.828 2.380 2.365 2.406 0.740 0.937 16,700
1% 2.938 3.187 1.920 2.380 2.365 2.406 0.740 0.937 18,000
17/ ,s 2.938 3.187 2.012 2.397 2.365 2.406 0.740 1.000 19,500
11/i 3.000 3.437 2.104 2.473 2.365 2.473 0.847 1.062 21 ,000
1% 3.063 3.437 2.288 2.623 2.365 2.510 0.847 1.125 24,000
111;,s 3.250 3.437 2.379 2.699 2.365 2.635 0.970 1.187 26,000
113/,s 3.250 3.437 2.563 2.849 2.365 2.822 0.990 1.250 29,000
11
TABLE 9 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT}, REGULAR AND LONG LENGTH, 11/i in. DRIVE
Outside Diameter, in.
Nut
Overall Length, in. Nut End, Drive End, Opening Bolt Clearance
Nominal C D Depth, Hole Diameter,
Opening, Regular, Long, A E
in. Max. Min. Min. Max. Min. Max. in., Min. in., Min.
12
~
003 by the American Society of Mechanical Engineers .
., \.. .,, ...... .-. A.,. ,..+ .. i.; .. ...... ,.+ .,.. ..;,.. \ •• •;+i,. ,.. .,t- .. ... ; ..,..,. .... ,.,,.,. ... .. ,... ... + .... +' A C'l'I.A'C
Licensed to Jessica Hooker. ANSI order >i 429079 Downioadea 2i1812010 12:4? PM. Single user 1,cens& only. Copying ,md networking prohibited.
TABLE 9 TYPE I, CLASS 1 AND 2, SINGLE HEXAGON (6-POINT) AND DOUBLE HEXAGON
(12-POINT), REGULAR AND LONG LENGTH, 1% in. DRIVE (CONT'D)
Outside Diameter, in .
Overall Length, in. Nut End, Drive End, Nut Bolt Clearance
Nominal C D Opening Hole Diameter,
Opening, Regular, Long, Depth, A E
in. Max. Min. Min. Max. Min. Max. in ., Min. in., Min.
TABLE 10 TYPE I, CLASS 1, SINGLE HEXAGON (6-POINT), REGULAR LENGTH, 2% in. DRIVE
Outside Diameter, in.
Overall Nut Bolt Clearance
Length, Nut End, Drive End, Opening Hole
in., C D Depth, Diameter,
Nominal Regular, A E
Opening, in. Max. Max. Max. in., Min. in., Min.
13
TABLE 11 TYPE II, CLASS 1 AND 2, SINGLE SQUARE (4-POINT) AND DOUBLE SQUARE
(8-POINT), REGULAR AND LONG LENGTH SOCKETS, % in. DRIVE
Overall Length, in. Outside Diameter, in.
Nut Bolt Clearance
8 Point 4 Point Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, Regular, A E lbf-in.,
Opening, in. Max. Min. Max. Min. Max. Min. Max. in., Min. in., Min. Min.
1/4 1.000 1.437 1.000 0.466 0.491 0.677 0.697 0.087 0.156 270
s;,s 1.000 1.437 1.000 0.559 0.666 0.677 0.760 0.102 0.171 440
%
7
1.000 1.437 1.000 0.637 0.760 0.677 0.760 0.117 0.281 660
1,s 1.063 1.437 0.740 0.854 0.740 0.854 0.203 0.281 930
TABLE 12 TYPE II, CLASS 1 AND 2, SINGLE SQUARE (4-POINT) AND DOUBLE SQUARE (8-POINT),
REGULAR AND LONG LENGTH, 1/z in. DRIVE
Overall Length, in. Outside Diameter, in.
Nut Bolt Clearance
8-Point 4-Point Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, Long, A E lbf-in.,
Opening, in. Max. Min. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
%
7
1.800 3.187 3.187 0.697 0.760 0.865 1.010 0.117 0.281 1100
1,s 1.800 3.187 3.187 0.802 0.860 0.927 1.010 0.203 0.281 1500
%
9/,s
1.800 3.187 3.187 0.898 0.978 0.927 1.041 0.209 0.344 2000
1.800 3.187 3.187 0.990 1.041 0.990 1.138 0.249 0.406 2600
% 1.800 3.187 1.099 1.166 1.104 1.197 0.281 0.469 3300
,,/,s 1.800 3.187 1.178 1.260 1.178 1.260 0.318 0.469 4100
%
13
1.800 3.187 1.302 1.343 1.115 1.385 0.356 0.531 5000
116 1.800 3.187 1.365 1.447 1.115 1.447 0.418 0.594 5000
71s 1.800 3.187 1.490 1.573 1.245 1.572 0.479 0.594 5000
,s 2.100 3.437 1.601 1.666 1.302 1.697 0.490 0.656 5000
116
14
TABLE 13 TYPE II, CLASS 1 AND 2, SINGLE SQUARE (4-POINT) AND DOUBLE SQUARE (8-POINT),
REGULAR AND LONG LENGTH, in. DRIVE %
Overall Length, in. Outside Diameter, in.
Nut Bolt Clearance
8-Point 4-Point Nut End, Drive End, Opening Hole Proof
C D Depth, Diameter, Torque,
Nominal Regular, Long, Regular, Long, A E lbf-in.,
Opening, in. Max. Min. Max. Min. Min. Max. Min. Max. in., Min. in., Min. Min.
1/2 2.250 2.937 2.250 2.937 0.990 1.073 1.490 1.635 0.209 0.344 2000
s;,s 2.250 2.937 2.250 2.937 1.146 1.166 1.490 1.635 0.249 0.406 2600
% 2.250 2.937 2.250 2.937 1.240 1.260 1.490 1.635 0.281 0.469 3300
,,/,s 2.250 2.937 2.250 2.937 1.333 1.354 1.490 1.635 0.318 0.469 4100
% 2.313 2.937 2.313 2.937 1.490 1.635 1.490 1.635 0.356 0.531 5000
13 2.438 2.937 2.438 2.937 1.615 1.698 1.615 1.760 0.418 0.594 5000
116
71a 2.438 2.937 1.740 1.760 1.615 1.826 0.479 0.594 5000
,s 2.438 2.937 1.802 1.826 1.615 1.826 0.490 0.656 5000
116
1 2.594 2.937 1.927 2.135 1.615 2.135 0.490 0.656 5000
11!,s 2.594 2.937 1.990 2.135 1.740 2.135 0.490 0.687 5000
11/a 2.750 2.937 2.115 2.322 1.740 2.322 0.632 0.781 5000
1% 2.750 2.937 2.365 2.447 1.740 2.447 0.632 0.812 5000
1s/,s 2.750 2.937 2.490 2.697 1.740 2.697 0.740 0.937 5000
17/,s 2.750 2.615 2.697 1.740 2.697 0.740 1.000 5000
11/2 2.750 2.740 2.823 1.740 2.823 0.847 1.062 5000
TABLE 14 TYPE Ill, CLASS 1 AND 2, UNIVERSAL, SINGLE HEXAGON (6-POINT) AND DOUBLE
HEXAGON (12-POINT), REGULAR AND LONG LENGTH, % in. DRIVE
7
% 2.500 2.750 0.520 0.760 0.677 0.910 0.117 0.281 0.937 450
1,s 2.500 2.750 0.607 0.760 0.677 0.910 0.203 0.281 0.937 625
Yi 2.500 2.750 0.677 0.823 0.677 0.910 0.209 0.344 0.937 725
s;,s 2.500 2.750 0.740 0.850 0.677 0.910 0.249 0.406 0.937 750
% 2.500 2.750 0.855 0.948 0.730 0.910 0.281 0.469 0.937 750
, 11,s 2.650 3.250 0.970 1.010 0.730 0.910 0.318 0.469 0.937 750
% 2.650 3.250 1.030 1.135 0.730 0.910 0.356 0.531 0.937 750
15
TABLE 15 TYPE Ill, CLASS 1 AND 2, UNIVERSAL, SINGLE HEXAGON (6-POINT) AND DOUBLE
HEXAGON (12-POINT), REGULAR AND LONG LENGTH, in. DRIVE 1/i
Bolt
Outside Diameter, in.
Nut Clearance
Overall Length, in. Nut End, Drive End, Opening Hole Depth of Bolt Proof
C D Depth, Diameter, Clearance Torque,
Nominal Regular, Long, A E Hole, lbf-in.,
Opening, in. Max. Min. Min. Max. Min. Max. in., Min. in., Min. in., Min. Min.
7
/15 3.000 3.500 0.600 0.814 0.865 1.063 0.203 0.281 1.250 850
112 3.000 3.500 0.681 0.891 0.865 1.063 0.209 0.344 1.250 1000
9
/15 3.000 3.500 0.763 0.968 0.865 1.063 0.249 0.406 1.250 1350
% 3.000 3.500 0.844 1.046 0.865 1.063 0.281 0.469 1.250 1500
11;15 3.000 3.500 0.926 1.123 0.927 1.250 0.318 0.469 1.250 1750
% 3.000 3.500 1.001 1.260 0.927 1.250 0 .356 0.531 1.250 1750
13;16 3.000 3.500 1.009 1.278 0.927 1.250 0.418 0.594 1.250 1750
%
1s
3.000 3.500 1.178 1.355 0.927 1.250 0.479 0.594 1.250 1750
116 3.250 3.750 1.252 1.433 0.927 1.250 0.490 0.656 1.250 1750
1 3.250 3.750 1.333 1.510 0.927 1.250 0.490 0.656 1.250 1750
11/15 3.500 3.750 1.364 1.515 0.927 1.250 0.490 0.687 1.250 1750
1 %
3
3.500 3.750 1.439 1.590 0.927 1.250 0.632 0.781 1.250 1750
1 /15 3.500 3.750 1.514 1.665 0.927 1.250 0.632 0.796 1.250 1750
1% 3.500 3.750 1.588 1.740 0.927 1.250 0.632 0.812 1.250 1750
15/15 3.500 3.750 1.663 1.815 0.927 1.250 0.748 0.906 1.250 1750
16
17
18
ASME Services
ASME is committed to developing and delivering technical information. At ASME's Information Central, we make
every effort to answer your questions and expedite your orders. Our representatives are ready to assist you in the
following areas:
There are four options for making inquiries* or placing orders. Simply mail, phone, fax, or E-mail us and an Information
Central representative will handle your request.
* Information Central staff are not permitted to answer inquiries about the technical content of this code or standard.
Information as to whether or not technical inquiries are issued to this code or standard is shown on the copyright
page. All technical inquiries must be submitted in writing to the staff secretary. Additional procedures for inquiries
may be listed within.
The ASME Publications Catalog shows a complete list of all the Standards published by the Society. For a
complimentary catalog, or the latest information about our publications, ca/11-800-THE-ASME (1-800-843-2763).