Professional Documents
Culture Documents
D ATA KAPAL
Nama Kapal : KT. ARJUNA I 206
Jenis : HARBOUR TUG (Twin Screw)
Ukuran :
Loa : 23.54 m
Lpp : 21.93 m
B (mould) : 7.00 m
H (mould) : 3.15 m
T: 2.40 m
Pemilik : PT. PELABUHAN INDONESIA (PERSERO) CAB TANJUNG PRIOK
Kelas : BIRO KLASIFIKASI INDONESIA
Jenis Survey : DOCKING SURVEY, INTERMEDIATE SURVEY
Job
Job Name Volume Unit
Code
Specifications
- Docking report dibuat dalam satu buku dengan cover yang baik
- Laporan megger test, NDT dan UTM agar dimasukkan ke docking report
- Docking report sebanyak 2 (dua) pcs untuk Class dan Flag, sudah selesai maksimal 2 (dua) hari setelah kapal undocking.
- Lampiran docking report untuk Flag agar dibuat berwarna sesuai aslinya (lampiran photograph, NDT dll)
Specifications
- Scope of survey (Docking Survey, SS 2 Survey, Propeller Shaft Survey and Load Line Survey
- Endosement certificate (Hull Certificate, Machinery Certificate and Load Line Certificate)
Specifications
- Endosement certificate (Safety Construction Certificate, Safety Equipment Certificate, Safety Radio Certificate, IOPP
Certificate, Sanitary Certificate, International Tonage Certificate, Certificate of Nationality, etc)
112.3.1 Ultrasonic thickness gauging measurement (UTM), under water and main deck 350 Spot
Specifications
- UTM dilaksanakan oleh NDT company yang telah disetuhui oleh class/BKI
- Dilaksanakan oleh NDT inspector level II diwabah supervisi NDT level III
- Peralatan yang digunakan harus terkalibrasi yang terakreditasi oleh badan KAN
- Apabila terdapat suspect, pelat tipis, pelat buckling/deform, crack, korosi/pitting, agar segera diinformasikan ke owner
representative
Specifications
- Fire guard dan security agar dilengkapi dengan daftar kehadiran yang diketahui oleh master/chief engineer
- Tekanan air pada fire hose miniman 7 kg/cm2, dengan fire hose nozzle maks diameter 25 mm
- Fire line dapat menjangkau main deck, engine room dan daerah kerja panas
Specifications
Specifications
Specifications
- Supply air tawar agar dilengkapi dengan tanda terima yang diketahui oleh master/chief engineer
Specifications
- Pemindahan keel block/stop block & pillar apabila terdapat pekerjaan replating pada daerah keel block
- Dibuatkan dokumentasi pemindahan keel block yang disetujui oleh Owner Representative
Specifications
- Dinyatakan docking ketika kapal telah duduk, kondisi dry dock bersih dan pekerjaan docking dapat dimulai
- Penggunaan tug boat assistance apabila kapal tidak dapat bergerak sendiri
- Penggunaan alat berat (crane/forklift) sesuai kebutuhan kapal (bukan pekerjaan docking)
- Permintaan penggunaan alat berat diajukan oleh Master yang diketahui oleh Owner Representative dan dibuatkan bukti
penggunaaan alat berat
146.1.1 Clearing and cleaning bilge of engine room with chemical cleaning 1 Ls
146.1.2 Clearing and cleaning bilge of steering gear room with chemical cleaning 1 Ls
146.4 Oil tank and other tank cleaning and survey, manual cleaning
Specifications
- Temuan internal survey segera disampaikan ke owner representative pada kesempatan pertama
- Sebelum ditutup agar dilaksanakan final cek dengan master/chiefd eng yang diketahui oleh owner rep
Specifications
2 HULL
200 General Hull Work
200.1 Replating for hull construction, estimate 15000 Kg
200.3.4 Replating FWD Stbd side bulwark, include ship name with CNC cutting
Bulwark plate 10 mm, dim 2080 x 2370 2,080 x 2,370 x 10 x 1 = 387 387 Kg
Side ship name with CNC cutting, t 8 mm, alphabet height approx 300 mm 1 Ls
Bulwark plate 12 mm, dim 1120 x 3500 1,120 x 3,500 x 12 x 1 = 369 369 Kg
600 x 1,160 x 12 x 1 = 66 66 Kg
80 x 2,300 x 12 x 1 = 17 17 Kg
Make new brest hook (horizontal bkt) 750 above main deck, between FWD stanchion
Bulwark plate 8 mm, dim 500 x 3250 500 x 3,250 x 8 x 1 = 102 102 Kg
Bulwark plate 8 mm, dim 800 x 3250 800 x 3,250 x 8 x 1 = 163 163 Kg
200.5.3 Make new scalop on e/r the floor, dia 50 mm, finish with grinding and painting (touch up) 84 Spot
Specifications
- Dibuatkan repair plan, acuan gambar sheel expansion & construction profile
- Plate pada bagian dalam dan internal member dilaknsakan blasting painting
- Beksa bakaran pada material dilaksanakan power tool ST.3 dan di touch up paint
- Jika pada list tidak ada, pekerjaan sudah termasuk asistensi, akses dan scafolding
260.1.1 Dismantle and install tire fender, if any demage material owner supply
- Chain guards for tire fender with galvanized pipe dia 3" and plate ring t 10 mm 28 Pcs
# included install with welding (chain guards for tire fender) and painting
260.2.1 Fabrication pad eye for fender, t : 18 mm with doubler and pipe ring hole 40 Pcs
# Eye Pad, t : 18 mm; Pengelasan digerinda; Ujung potongan digerinda round melingkar
260.2.2 Dismantle and install pad eye for fender, t : 16 mm, estimate, material owner supply 40 Pcs
Renew man hole cover set (standard type) 400 x 600 mm t : 10 mm, steering gear room 2 pcs
- Cover plate, stud ring and handle with mill steel material
- Washer, stud bolt and nut with stainless steel material SUS 316
260.3.2 Maintenance small hatch coming for emcy e/r, AFT main deck
260.3.3 Maintenance and modification the sky light for crew room, FWD main deck
Renew and setting coming list plate, FB 70 x 12, dim approx 1600 mm 2 set
Maintenance hinge 1 Ls
Make new safety holder, using hook & eye or hinge pin 2 Pcs
260.4.2 Install arrow for door clip hatch coming and sky light
Intall arrow for door clip (toogle) with plate t : 4.5 dim 140 x 140, CNC cutting 6 Pcs
# Arrow design and dimension as per ISO standard, see drawing attachment
260.4.1 Renew small WT door for stering gear room, main deck
WET door dim 470 x 700, included hinge, handle, HASP, dog opener, hook & eye, arrow, neoprene packing 2 Unit
260.4.2 Renew small WET door for foam tk., main deck
WET door dim 600 x 740, included hinge, handle, HASP, hook & eye, neoprene packing 1 Unit
Renew and setting coming list plate, FB 70 x 12, dim approx 2700 mm 1 Ls
Intall arrow for door clip (toogle) with plate t : 4.5 dim 140 x 140, CNC cutting 24 Pcs
260.5.1 Renew vertical ladder main deck to FWD nav deck, using galvanized pipe
Renew ladder galvanized pipe Sch 80 dia 1¼" x 1200, 2 pics 2.4 m
Renew rung step galvanized pipe Sch 80 dia 1¼" x 380, 3 pics 1.1 m
Renew hand rail galvanized pipe Sch 80 dia 1¼" x 1700, 2 pics 3.4 m
260.6.1 Engine room mushroom and ventilator, nominal dia 12", AFT Stbd side main deck
Maintenance and over hauling mushroom, shaft & bearing, handwhell/spindle and painting 1 Set
260.6.2 Over houling elmot of ventilator reference to megger test, if any 1 Set
260.7.1 Maintenance and renew towing guard pipe, AFT main deck
PVC laminated for towing guard pipe using half PVC pipe AW type 1 Ls
260.7.2 Maintenance and renew double cross bit, FWD main deck
Longitudinal carling, L 100 x 100 x 10, length 500 x 4 pcs 200 x 500 x 10 4 = 31 31 Kg
260.8.2 Renew bracket for chain locker/mud pump, FWD main deck Stbd side
Cable/tubing penetration for AC on AFT nav deck PS, AC for salon, nav deck 1 Ls
Make new flagpole with galvanized pipe SCH 80 dia 1½", AFT nav deck 1 Ls
* Material estimation
'Doubler dia150 x 12
Make new allumunium lifebuoy rope box & self igniting light, steel box dim 350 x 300 x 500 (LBH)
Fabrication and install allumunium lifebuoy box. Include hinge, hanger/handle, bracket, cover 2 Pcs
Make new lifebuoy rope box, steel box dim 200 x 150 x 350 (LBH)(Panjang x Lebar x Tinggi)
Fabrication and install allumunium lifebuoy box. Include hinge, hanger/handle, bracket, cover 4 Pcs
260.9.2 Fab and install side ship name "ARJUNA I 206" on top deck P/S
Ship name material stainless SUS 316L, alphabet height 120 mm, CNC cutting, knock down system 2 Set
260.9.3 Fabrication and install Install JAI logo (IPC MARINE) on funnel, P/S
Plate thickness 4 mm, alphabet height 120 mm, CNC cutting, knock down system 2 Ls
Renew pipe suport with galvanized pipe sch 80 dia 2" x 130, as much 6 pcs 1 Ls
SS bolt, nut & washer (SUS 316 M10 x 30), M10 6 Pcs
260.9.6 Fab and install GT number, material SUS 316L t 4 mm, alphabet haigh 120 mm, knock down system
" GT 129 NO 3656/II K ", alphabet haigh 120 mm, CNC cutting, knock down system, FWD bhd main deck 1 Ls
" 2008 II k No. 4485/L ", alphabet haigh 120 mm, CNC cutting, knock down system, FWD bhd main deck 1 Ls
260.9.7 Make new spare part cabinet using carbon steel material t 5 mm with epoxy painting
Fabrication and install spare part cabinet dim 1000 x 60 x 1000 (LBH) . Include hinge, hanger/handle, key/lock etc 1 Set
Fabrication and install allumunium deep tray, dim 300 x 300 x 150 (LBH), included drain plug and gasket 2 Set
Specifications
- Pemasangan rubber/tire fender sudah termasuk assesorisnya (rantai, segel, turnbuckle dll)
- Jika pada list tidak ada, pekerjaan sudah termasuk asistensi, akses dan scafolding
Specifications
- Pemasangan sea greating dilengkapi dengan safety lock bolt, brass wire or lock plate
- Jika pada list tidak ada, pekerjaan sudah termasuk asistensi, akses dan scafolding
Hull scraping, include sea chest, skeg and rudder/kort nozzle 74.2 m2
Hull cleaning with high pressure washing, bottom until bulwark 306.4 m2
Draft Marking, Plimsol Mark, Tank Marking, Ship Name, Port Register etc 1 ls
270.2.1 Main deck until top deck and internal bulwark blasting
270.2.2 Main deck until top deck and internal bulwark coating, material owner supply
- Solvalitt 7 5 Ltr
Specifications
- Apabila blasting dilaksanakan secara partial, sebelum pengecatan lapis kedua agar dilaksanakan pencucian dengan air tawa
- Apabila terdapat repair karena hot work, minimal dilaksanakan power tool St. 3 & touch up
- Pengecatan yang rusak karena hot work segera diperbaiki sebelum pengecatan lapis kedua
- Blasting dan pengecatan pada deck termasuk 150 mm pada dinding, outfitting/pipa yang menempel pada deck
- Blasting dan painting pada deck termasuk 150 mm pada daerah dinding dan out-fitting/pipa yang menempel pada deck
- Jika pada list tidak ada, pekerjaan sudah termasuk asistensi, akses dan scafolding
278.2 Install anode for hull (bolt type), material owner supply
Specifications
- Jika pada list tidak ada, pekerjaan sudah termasuk asistensi, akses dan scafolding
288.2 Install anode for water ballast tk., material owner supply
Specifications
4 Ship Equipment
413 Gyro Plants, Autopilots, Compasses
413.1 Maintenance GPS
431.1.1 Maintenance GPS marine Furuno GP-32, demaged screen of monitor 1 unit
Specifications
Specifications
415.2.1 Provide and install wiper blade 24", bosch Aerotwin Plus Multiclip 24 inch 5 unit
Specifications
Specifications
421.1.1 Provide and install VHF manire transceiver, iCOM M330 1 Unit
421.1.2 Provide and install speaker on salon room, speaker Altec Lansing AL-BX520 2 pcs, audio cable the titan 2 x 1.5 approx 15 m 1 Set
421.2.1 Provide and install SSB manire transceiver, iCOM IC-718 1 Unit
Specifications
427.2.1 Provide emergency fire protection for engine room exhaust and FO pump, emergency stop location on the wheel hous and external engine room 1 Ls
427.2.2 Install New Auto Swithc For Dual Power Supply 1 set
427.2.3 Provide and install automatic battery charger, solid state circuit 50 A - Auto Charging On/Auto Cut Off - Short Circuit Protection - Auto Detection Battery 1 unit
427.2.4 Repair and maintenance disboard panel 24 V for nav and com 1 Ls
Internal
429 communication
429.1 Maintenance public address
429.1.1 Provide and install PA amplifier, TOA ZA-2505 - DC completed with mic 1 unit
431.2 Blasting and painting anchor and anchor chain & fitting, material yard supply 2 set
431.7 Renew swivel set, diameter as per chain calibration and gupsy size (est. 20 mm/rule dia 14 mm) 2 set
431.8 Renew anchor shackle, diameter as per chain calibration and gupsy size (est. 20 mm/rule dia 14 mm) 2 Pcs
431.9 Renew kenter shackle, diameter as per chain calibration and gupsy size (est. 20 mm/rule dia 14 mm) 2 Pcs
431.10 Renew anchor chain, diameter as per chain calibration and gupsy size (22 mm/rule dia 14 mm) and length as per rule 1 Skl
431.11 Renew push button station (start/stop box) IP 67, 3 phase, 8A @ 600VAC, steel enclosure material, Schneider/siemen 1 set
Specifications
Install manual quick release, with SS wire (wire dia approxs 6 mm x 6m) 1 ls
Specifications
- Disediakan spare napple grace untuk crew maintenance & napple gun
Provide and install marine boat pilot chair, seat height may be angle adjusted - can be moved back and front - folding/angle adjustable - can rotated 1 Set
Two shelfing cabinet with playwood 25 mm, TACO HPL laminations, dim 2.1 x 0.4 x 0.95 m (Lxbxh) 2 m2
Three shelfing file cabinet with playwood 25 mm, TACO HPL laminations, dim 1.2 x 0.8 x 1.25 m (Lxbxh) 1 m2
Two shelfing file cabinet with playwood 25 mm, TACO HPL laminations, dim 0.3 x 0.82 x 0.4 (Lxbxh) 1 m2
Step shelfing with playwood 25 mm, TACO HPL laminations, dim 820 x 500 mm (Lxb) 1 Ls
Make new bench cushion seat (140 + 185) x 60 x 45 Cm (Lxbxh), with playwood 25 mm and TACO HPL lamination 1 Set
Install foam (140 + 180) x 55 x 20 Cm (Lxbxt), with INOAC foam (medium hard violence) and oscar/PU (MBTech Giorgio) cover 1 Set
Renew back bench cushion (140 + 185) x 45 Cm (Lxb), with playwood 25 mm and TACO HPL lamination 1 Set
Install foam (140 + 180) x 45 x 20 Cm (Lxbxt), with INOAC foam (medium hard violence) and oscar/PU (MBTech Giorgio) cover 1 Set
Make new table of sofa, with playwood 25 mm and TACO HPL lamination and galvanized pipe/pillar dia 6 inch 1 Set
Renew stainless wire mesh 316 (mesh 8 - mesh 12), dim 660 x 1350 2 Set
Remove ceramic and deck covering (work assistance per job code 821.5.1) 2 m2
Use Roman Granit motif dCaesar Grey (GT609860FR), floor dim 1800 x 1100 mm 2 m2
Cutting and blank discharge pipe dia 2½" and doubling plate t 10 dia 100 1 Ls
Repair frame door using waterproof cement, dim 600 x 180 x 100 1 Ls
Specifications
- Ceiling dan lining menggunakan ACP dengan tebal min 4 mm dan coating 0,3 glossy
- Rangka menggunaka besi holo profile yang di cat primer AC, min tebal holo 3.2 mm
- Termasuk pekerjaan asistensi/bongkar pasang peralatan dan interior (meja, kursi, tv, kulkas dll)
- Vinyl untuk lantai menggunakan bahan TACO vinyl dengan motif kayu
Maintenance
601.2.10 TURBOCHARGER
601.2.23 TAMBAHAN :
Specifications
631.3 Dismount/ Install, cleaning/polishing and balancing, if any per conditions 1 unit
631.5 Build up weld for pitting and other defect on the propeller blade, if any 1 unit
631.6 NDT propleller, shaft and rudder stock, if any as clearance measurement report 1 ls
Specifications
- NDT dilaksanakan oleh NDT company yang telah disetuhui oleh class/BKI
- Dilaksanakan oleh NDT inspector level II diwabah supervisi NDT level III
Shafting,
632
Stern Tubes, Tunnel
632.1 Dismount/ Install shaft propeller, if any as clearance measurement report or visual condition 1 unit
632.2 Dismount/ Install rudder blade, if any as clearance measurement report or visual condition 1 unit
632.3 Dismount/ Install rudder stock, if any as clearance measurement report or visual condition 1 unit
632.4 Shaft deflection alignment, if any as per shaft deflection measurement 1 unit
632.5 Renew rubber bearing of stern tube, if any (material yard supply) 1 unit
632.6 Renew bearing of rudder pintle, if any (material yard supply) 1 unit
Specifications
- NDT dilaksanakan oleh NDT company yang telah disetuhui oleh class/BKI
- Dilaksanakan oleh NDT inspector level II diwabah supervisi NDT level III
Last O/H
650.2.1 Alternator No. 1 (175 kVA) cleaning & coating, if any (based on megger test result) 1 Set
650.2.2 Alternator No. 2 (175 kVA) cleaning & coating, if any (based on megger test result) 1 Set
800.1.1 Main sea chest valve, Gate valve 10k 200 Port side 1 pcs
800.1.2 Main sea chest valve, Globe valve 10k 200 Stbd side 1 pcs
800.1.3 Second sea chest valve, Buterfly valve DN 200 P & S 2 pcs
800.2.4 Discharge from bilge/ballast pump, Globe valve 125S 200 WOG 1 pcs
800.2.5 Discharge from GS pump, Globe Valve 125S 200 WOG 1 pcs
800.2.6 Discharge from bathroom, Globe Valve 125S 200 WOG 1 pcs
800.2.8 Discharge from Galley, Globe valve 125S 200 WOG 1 pcs
800.2.9 Discharge from SWC Fire Fighting Engine, Check valve 10k 40 1 pcs
800.3.3 Suction to Main Seawater cooling valve Stbdside AE 5k 40 Buterfly Valve 1 pcs
800.3.4 Suction to SWC Fire fighting Engine, Globe valve 10k 150S 1 pcs
800.5.1 FW Suction Valve from Double bottom Tanks, Globe valve 1½ 5k 2 pcs
- Apabila terdapat valve yang rusak, agar diinfokan jenis valve, ukuran dan fungsinya
813.1.1 Insatall new bilge alarm with bilge sound, alarm integrated with general alarm 1 Ls
814.1.1 Service & repiar fire monitor, electrical and mechanical mot fuction 2 unit
Specifications
- Material yang digunakan seamless pipe dengan ketebalan mengacu pada class rule
- Bongkar pasang/penggantian pipa sudah termasuk packing, bolt, nut dan washer
- Apabila terdapat penggantian spare part agar diinformasikan pada kesempatan pertama
- Dilaksanakan uji kebocoran dan uji fungsi pada penggantian pipa baru
- Flens 5K 80 2 Pcs
- Flens 5K 80 3 Pcs
820.2.3 Renew discharge pipe to stern tube, for main engine SCW P
- Flens 5K 25 2 Pcs
- Flens 5K 80 2 Pcs
- Flens 5K 80 2 Pcs
- Flens 5K 65 5 Pcs
- Flens 5K 65 3 Pcs
- Flens 5K 65 2 Pcs
- Flens 5K 65 3 Pcs
- Flens 5K 65 6 Pcs
- Flens 5K 65 2 Pcs
- Flens 5K 50 10 Pcs
- Flens 5K 50 2 Pcs
- Flens 5K 20 4 Pcs
820.12 FO Pipe
- Flens 5K 65 3 Pcs
- Material yang digunakan seamless pipe dengan ketebalan mengacu pada class rule
- Bongkar pasang/penggantian pipa sudah termasuk packing, bolt, nut dan washer
- Dilaksanakan uji kebocoran dan uji fungsi pada penggantian pipa baru
821.2.1 Renew pipe penetration dia 1¼", pipe SCH 160 1 pcs
821.2.2 Renew pipe penetration dia 2", pipe SCH 160 4 pcs
821.2.3 Renew pipe penetration dia 2½", pipe SCH 160 13 pcs
821.3.1 Renew air pipe, model gooseneck ventilator type A JIS F2408, pipe SCH 80 dia 2½" 2 Set
821.4.1 Renew filling pipe SCH 80 dia 2½" with cap, SB 1 Set
- Bracket 75 x 75 x 10 4 Pcs
821.6.2 Make new deck scupper from AFT nav deck to main deck P/S, pipe in side of wall
- ISC Fire flange, 4 hole t : 14.5 OD 178 ; PCD 132, include blind flange bolt nut and packing 1 Ls
- Material yang digunakan seamless pipe dengan ketebalan mengacu pada class rule
- Bongkar pasang/penggantian pipa sudah termasuk packing, bolt, nut dan washer
- Dilaksanakan uji kebocoran dan uji fungsi pada penggantian pipa baru
Renew pressure gauge, scale range 0 to 10 bar, schuh/wika SS/SX series 1 Pcs
860.5 Pump driver/motor overhouling, if any (reference megger test result, bellow 1 mega ohm) 1 unit
# included rewinding
Specifications
- Sudah termasuk penggantian part yang kecil (mur, baut, washer, rames/packing dll)
- Dilaksanakan megger test pada o/h elmot pada saat sebelum dan sesudah perbaikan
- Pada over haul pompa agar dilaksanakan performance test untuk mengetahui kekuatan pompa (head, kapasitas dan kuat a
- Dilaksanakan uji fungsi (function test) apabila perbaikan hanya pada elmot.
Specifications
xx Provisional Sum
1,500 x 150
SCH 80
½"
Pipa 250000
Elbow 90000 14000
Flange 65000 32000
Support 60000
Hose 25000
1"
Pipa 300000
Elbow 100000 16400
Flange 90000 60000
Support 80000
Hose 30000
1¼"
Pipa 350000
Elbow 111000 22200
Flange 95000 64000
Support 85000
Hose 35000
1½"
Pipa 450000
Elbow 173500 34700
Flange 100000 68000
Support 90000
Hose 40000
2"
Pipa 600000
Elbow 251000 50200
Flange 120000 80000
Support 100000
Hose 50000
2½"
Pipa 800000
Elbow 380000 95000
Flange 150000 100000
Support 120000
Hose 60000
3"
Pipa 950000
Elbow 375000 150000
Flange 200000 120000
Support 140000
Hose 80000
4"
Pipa 1200000
Elbow 500000 250000
Flange 225000 130000
Support 160000
Hose 100000
Twin Screw)
x 7 1 = 12 12.4 Kg
6.42857142857
2.03125
6.09756097561
1.5
5
1.484375
5
1.47058823529
5
4
1.5
2.5
1.66666666667
2
1.73076923077
Job Code Job Name Volume Unit
Panjang x Lebar x Tebal x Juml = Kg
1 GENERAL SHIP
100 Specification, Drawing and Document
100.1 Docking Report 6 Pcs
100.1 Specifications
100.1 - Docking report dibuat dalam satu buku dengan cover yang baik
100.1 - Docing report dilengkapi sbb :
100.1 Surat Keterangan Doking
100.1 Berita Acara Docking dan Berita Acara Undocking
100.1 Gambar repair plan pada bukaan kuliit
100.1 Material traceability report (MTR) beserta rubing dan sertifikat
100.1 Laporan - laporan pengukuran
100.1 - Laporan megger test, NDT dan UTM agar dimasukkan ke docking report
100.1 - Memorandum BKI agar dimasukkan ke docking report
100.1 - Sertifikat fre TBT anti fouling agar dimasukkan ke docking report
100.1 - Docking report sebanyak 2 (dua) pcs untuk Class dan Flag, sudah selesai maksimal 2 (dua) hari setelah kapal undocking.
100.1 - Lampiran docking report untuk Flag agar dibuat berwarna sesuai aslinya (lampiran photograph, NDT dll)
100.1 - Dibuatkan laporan berupa soft copy
119 Accommodations
199.1 Penginapan untuk crew kapal
199.1 Menyediakan penginapan untuk 10 orang crew selama docking 0 day
199.2 Penginapan untuk owner representative
199.2 Menyediakan penginapan untuk 2 orang selama docking 0 day
DRY DOCKING KT. ARJUNA I 206 REPAIR LIST SPECIFICATION 33 of 52
Job Code Job Name Volume Unit
199.2 Transportasi untuk crew kapal
199.2 Menyediakan transportasi untuk 10 orang crew selama docking, per mobil 0 day
199.2 Specifications
199.2 - Penginapan untuk crew dapat berupa rumah atau losmen
199.2 - Satu kamar dapat ditinggali maksimal 2 (dua) orang
199.2 - Master tinggal dalam 1 (satu) kamar
199.2 - Chief engineer tinggal dalam 1 (satu) kamar
199.2 - Jumlah kamar sesuai dengan jumlah jadwal piket jaga crew
199.2 - Kamar dilengkapi dengan pendingin ruangan (AC)
199.2 - Penginapan untuk owner representative dapat berupa hotel
199.2 - Transportasi dapat berupa mobil penumpang atau antar jemput ke penginapan
2 HULL
DRY DOCKING KT. ARJUNA I 206 REPAIR LIST SPECIFICATION 35 of 52
Job Code Job Name Volume Unit
200 General Hull Work
200.1 Replating for hull construction, estimate 15000 Kg
200.2 Replating deck plate, main deck
200.3 Repair for bulwark
200.3.1 Renew bulwark top list PS, main deck
200.3.1 Bulwark flat bar FB 80 x 12, L 13000 13,000 x 80 x 12 x 1 = 98 98 Kg
200.3.2 Renew bulwark top list SB, main deck
200.3.2 Bulwark flat bar FB 80 x 12, L 13000 13,000 x 80 x 12 x 1 = 98 98 Kg
200.3.3 Insert plate for stanchion of bulwark SB, main deck
200.3.3 Stay t : 10 mm, T 250 x 400 + FB 75 x 400 , 4 Pcs 325 x 40 x 10 x 4 = 4 4 Kg
200.3.4 Replating FWD Stbd side bulwark, include ship name with CNC cutting
200.3.4 Bulwark plate 10 mm, dim 2080 x 2370 2,080 x 2,370 x 10 x 1 = 387 387 Kg
200.3.4 Side ship name with CNC cutting, t 8 mm, alphabet height approx 300 mm 1 Ls
200.3.5 Insert plate for FWD bulwark, main deck
200.3.5 Bulwark plate 12 mm, dim 1120 x 3500 1,120 x 3,500 x 12 x 1 = 369 369 Kg
200.3.5 Stay t : 12 mm, T 600 x 1160 + FB 80 x 2300
200.3.5 600 x 1,160 x 12 x 1 = 66 66 Kg
200.3.5 80 x 2,300 x 12 x 1 = 17 17 Kg
200.3.5 Make new brest hook (horizontal bkt) 750 above main deck, between FWD stanchion
200.3.5 Brest hook FWD FB 100 x 650 x 14, 2 pcs 100 x 650 x 14 x 2 = 14 14 Kg
200.3.5 Brest hook P/S FB 100 x 780 x 14, 2 pcs 100 x 780 x 14 x 2 = 17 17 Kg
200.4 Repair for super structure constructions
200.4.1 Replating top deck
200.4.1 Bulwark plate 8 mm, dim 500 x 3250 500 x 3,250 x 8 x 1 = 102 102 Kg
200.4.1 Bulwark plate 8 mm, dim 800 x 3250 800 x 3,250 x 8 x 1 = 163 163 Kg
200.4.1 * Work assistence see carpentry/interior job (541)
200.5 Repair welding
200.5.1 Rewelding seams joint, estimate 30 m
200.5.2 Welding pitting, estimate 300 Spot
200.5.3 Make new scalop on e/r the floor, dia 50 mm, finish with grinding and painting (touch up) 84 Spot
200.5.3 Specifications
200.5.3 - Dibuatkan repair plan, acuan gambar sheel expansion & construction profile
200.5.3 - Dibuatkan inspection and test plan (ITP)
200.5.3 - Dibuatkan material traceability report (MTR), ident/rubing & mill certificate
200.5.3 - Material dan fit-up agar dicek oleh quality control
200.5.3 - Sambungan plate diatas 6 mm harus di bevel
200.5.3 - Hasil potongan digerinda dengan ujung-ujungnya di round > 2 mm
200.5.3 - Plate pada bagian dalam dan internal member dilaknsakan blasting painting
200.5.3 - Beksa bakaran pada material dilaksanakan power tool ST.3 dan di touch up paint
200.5.3 - Back gouging agar diperiksakan ke owner representative
200.5.3 - Finishing pada back gouging agar digerinda
200.5.3 - Welding agar diperiksakan ke owner representative
200.5.3 - Sertifikat juru las agar disampaikan pada kesempatan pertama
200.5.3 - Cacat-cacat pengelasan agar diperbaiki sebelum pemeriksaan
200.5.3 - Finishing pada welding agar digerinda
200.5.3 - Dilaksanakan pengujian kebocoran sesuai aturan class (vacuum test/air test)
200.5.3 - Jika pada list tidak ada, pekerjaan sudah termasuk asistensi, akses dan scafolding
4 Ship Equipment
403 Steering gear, emergency steering plants, telemotor system
403.1 Steering gear
403.1 Specifications
403.1 - Pekerjaan pemeliharaan setelah pembongkaran dilaksanakan di workshop
403.1 - Pekerjaan pemeliharaan termasuk penggantian spare part
403.1 - Pekerjaan sudah termasuk pekerjaan asistensi yang berhubungan dengan pekerjaan utama
403.1 - Dilaksanakan fuction test dan dibuatkan laporannya
telephone plants,
425
walki talkies, etc
425.1 Renew horn on top deck 0 LS
Shafting,
632
Stern Tubes, Tunnel
632.1 Dismount/ Install shaft propeller, if any as clearance measurement report or visual condition 1 unit
632.2 Dismount/ Install rudder blade, if any as clearance measurement report or visual condition 1 unit
632.3 Dismount/ Install rudder stock, if any as clearance measurement report or visual condition 1 unit
632.4 Shaft deflection alignment, if any as per shaft deflection measurement 1 unit
632.5 Renew rubber bearing of stern tube, if any (material yard supply) 1 unit
632.6 Renew bearing of rudder pintle, if any (material yard supply) 1 unit
632.6 Specifications
632.6 - Pengukuran clearance disampaikan pada kesempatan pertama
632.6 - Dilaksanakan pengukuran defleksi poros/shaft deflection
632.6 - Apabila poros/shaft dijabut, dilaksanakan pengukuran pada area bantalan
632.6 - Apabila shaft dicabut, sudah termasuk penggantian remes packing
632.6 - Apabila bearing diganti, sudah termasuk machining dan pemasangan
632.6 - Dilaksanakan NDT yang disaksikan oleh owner representative
632.6 - NDT dilaksanakan oleh NDT company yang telah disetuhui oleh class/BKI
632.6 - Dilaksanakan oleh NDT inspector level II diwabah supervisi NDT level III
632.6 - Dibuatkan laporan/official report (hard copy) sebanyak 5 (lima) rangkap
632.6 - Dibuatkan laporan berupa soft copy