Professional Documents
Culture Documents
ELECTRONICS II
CH 12,13,14
Budoor Allwime
Dr. Mohamed Morsy
2020-2021
Q1 Q2 Q3 Q4 Total
CLO3 /12 /12
CLO4 /10 /10
CLO5 /10 /10
CLO6 /10 /10
TOTAL /12 /10 /10 /10 /42
FEEDBACK SUMMARY:
………………………………………………………………………………………………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………………………………………………………………………………………………
………………………………………………………………………………………………………………………………………………………………………………………………………………………
…………………………………………………………………………………………………………………………………………………………………………………………………………
STUDENT IDENTIFICATION:
Name ID Signature
By signing this form, the student recognizes that he understands and accepts the exam policy and ethics. He
recognizes also that if he does not respect these ethical rules, the professor will take the appropriate measures
including exclusion from the exam
|Page1
Question 1 (10 marks + 2 bonus)
For the circuit shown in Figure, use the given transistor
characteristic curves to answer the following:
a) Calculate the dc input power, power dissipated by the
transistor, ac power delivered to the load, and the
amplifier efficiency for a dc base current of 6 mA
and a peak base current swing of 4 mA.
b) Calculate the maximum output power and maximum
amplifier efficiency for a dc base current of 6 mA.
c) Repeat part (a) for a dc base current of 2 mA and a
peak base current swing of 4 mA.
d) What is the class of the amplifier in part
(a) and (c)?
e) Calculate the total harmonic distortion of
the output signal of part (c) if the output
signal having a dc component of 3.18 V,
a fundamental harmonic of 2.5 V, a third
harmonic of 0.8 V, and a fifth harmonic
of 0.13 V.
|Page2
|Page3
Question 2 (10 marks)
For the ADC Ladder network shown in Figure, answer the following:
a) Calculate the voltage resolution of the ADC.
b) Calculate the digital output and plot
the ladder network output voltage
for an analog input of 4V.
c) Calculate the conversion time for
the input of part (b) and the ADC
maximum conversion time.
𝑓 = 1𝑀𝐻𝑧
d) Plot the circuit of the ladder network
DAC. 8-bit DAC, 𝑉𝑟𝑒𝑓 = 10𝑉
e) What are the advantages and disadvantages of the Ladder ADC and DAC
networks?
|Page4
Question 3 (10 marks)
For the FET amplifier shown in Figure:
a) What is the feedback connection type?
b) Plot the block diagram of feedback circuit and
define A, β, and Af in terms of the circuit input
and output voltages and currents.
c) Calculate the voltage gain with and without
feedback.
d) Modify the amplifier circuit to design a 10 kHz
phase-shift oscillator. Plot the oscillator circuit
and specify the values of all circuit components. 𝑔𝑚 = 4 m𝑆, 𝑟𝐷 = 36 𝑘Ω
𝑅1 = 80 𝑘Ω, 𝑅2 = 20 𝑘Ω,
𝑅𝐷 = 10 𝑘Ω, 𝑅𝑂 = 10 𝑘Ω
|Page5
Question 4 (10 marks)
For the 60-Hz power supply circuit shown below:
a) Calculate the dc and ac voltage components and the ripple factor at node 1 for
𝑉𝑚 = 15𝑉 and a dc load current of 200 mA.
b) Plot the voltage waveform at nodes 1 and 2.
c) Calculate the minimum input voltage to maintain regulation for a dc load
current of 200 mA.
d) Calculate the maximum load current at which regulation is maintained for 𝑉𝑚 =
15𝑉.
|Page6
King Faisal University
College of Engineering
Department of Electrical Engineering
BME312 Bioelectronics II – Spring 2021
Quiz # 3 – April 11, 2021 Time: 15 minutes
Total: 3 Marks CLO 5
Name: …………………………………………………….. ID: …………………………..
BME312 Bioelectronics II, Spring 2021 King Faisal University Dr. Mohammed Farag Page 1
BME312 Bioelectronics II, Spring 2021 King Faisal University Dr. Mohammed Farag Page 2
King Faisal University
College of Engineering
Department of Electrical Engineering
BME312 Bioelectronics II – Spring 2021
Quiz # 2 – April 5, 2021 Time: 20 minutes
Total: 4 Marks CLO 7
Name: …………………………………………………….. ID: …………………………..
LM339
BME312 Bioelectronics II, Spring 2021 King Faisal University Dr. Mohammed Farag Page 1
2. For the circuit shown in Figure:
10 V
a) What is the maximum peak value of the ac
input VIN of the 566 VCO?
vo
b) Determine the output frequencies and plot the output voltage 𝑣𝑜 for the
following input waveform (VP = 1 V, T = 1 sec):
VIN (V)
t (sec)
BME312 Bioelectronics II, Spring 2021 King Faisal University Dr. Mohammed Farag Page 2