Professional Documents
Culture Documents
OWNER’S MANUAL
MODE D’EMPLOI
• Explanation of Graphical Symbols
CAUTION
RISK OF ELECTRIC SHOCK The lightning flash with arrowhead
DO NOT OPEN symbol, within an equilateral triangle,
is intended to alert you to the
presence of uninsulated “dangerous
CAUTION: TO REDUCE THE RISK OF voltage” within the product’s
ELECTRIC SHOCK, DO NOT REMOVE enclosure that may be of sufficient
COVER (OR BACK). NO USER-SERVICEABLE magnitude to constitute a risk of
PARTS INSIDE. REFER SERVICING TO electric shock to persons.
QUALIFIED SERVICE PERSONNEL.
The exclamation point within an
equilateral triangle is intended to alert
you to the presence of important
IMPORTANT operating and maintenance
Please record the serial number of this system in the (servicing) instructions in the
space below. literature accompanying the
appliance.
Model:
Serial No.:
The serial number is located on the rear of the main WARNING
unit. TO REDUCE THE RISK OF FIRE OR ELECTRIC
Retain this Owner’s Manual in a safe place for future SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
reference. OR MOISTURE.
SAFETY INSTRUCTIONS
1 Read Instructions – All the safety and operating 10 Power Sources – The unit should be connected to a
instructions should be read before the unit is operated. power supply only of the type described in the
operating instructions or as marked on the unit.
2 Retain Instructions – The safety and operating
instructions should be retained for future reference. 11 Power-Cord Protection – Power-supply cords should
be routed so that they are not likely to be walked on or
3 Heed Warnings – All warnings on the unit and in the pinched by items placed upon or against them, paying
operating instructions should be adhered to. particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the
4 Follow Instructions – All operating and other unit.
instructions should be followed.
12 Cleaning – The unit should be cleaned only as
5 Water and Moisture – The unit should not be used near recommended by the manufacturer.
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a 13 Nonuse Periods – The power cord of the unit should be
swimming pool, etc. unplugged from the outlet when left unused for a long
period of time.
6 Carts and Stands – The unit should be used only with
a cart or stand that is recommended by the 14 Object and Liquid Entry – Care should be taken so that
manufacturer. objects do not fall into and liquids are not spilled into
the inside of the unit.
6A A unit and cart combination should be
moved with care. Quick stops, excessive 15 Damage Requiring Service – The unit should be
force, and uneven surfaces may cause serviced by qualified service personnel when:
the unit and cart combination to overturn. A. The power-supply cord or the plug has been
damaged; or
7 Wall or Ceiling Mounting – The unit should be mounted B. Objects have fallen, or liquid has been spilled into
to a wall or ceiling only as recommended by the the unit; or
manufacturer. C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
8 Ventilation – The unit should be situated so that its exhibits a marked change in performance; or
location or position does not interfere with its proper E. The unit has been dropped, or the cabinet
ventilation. For example, the unit should not be damaged.
situated on a bed, sofa, rug, or similar surface, that
may block the ventilation openings; or placed in a built- 16 Servicing – The user should not attempt to service the
in installation, such as a bookcase or cabinet that may unit beyond those means described in the operating
impede the flow of air through the ventilation openings. instructions. All other servicing should be referred to
qualified service personnel.
9 Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances 17 Power Lines – An outdoor antenna should be located
that produce heat. away from power lines.
CONTENTS
SAFETY INSTRUCTIONS CONTROLS AND THEIR FUNCTIONS .......... 8
......................................... Inside of Front Cover
ADJUSTMENT BEFORE USING THE
CAUTION ......................................................... 2 SUBWOOFER ................................................. 9
Frequency characteristics .......................... 10
FEATURES ..................................................... 3
ADVANCED YAMAHA ACTIVE SERVO
PLACEMENT .................................................. 3
TECHNOLOGY ............................................. 11
CONNECTIONS .............................................. 4
TROUBLESHOOTING .................................. 12
Connecting to line output (pin jack)
terminals of the amplifier .............................. 4 SPECIFICATIONS ......................................... 12
Connecting to speaker output terminals
of the amplifier ............................................. 6
E-1
Thank you for selecting this YAMAHA subwoofer system.
4. Do not use force on switches, controls or connection 14. Secure placement or installation is the owner’s
wires. When moving the unit, first disconnect the responsibility.
power plug and the wires connected to other YAMAHA shall not be liable for any accident
equipments. Never pull the wires themselves. caused by improper placement or installation of
speakers.
5. Do not attempt to clean the unit with chemical solvents
as this might damage the finish. Use a clean, dry
For Canadian Customers
cloth.
To prevent electric shock, match wide blade of plug to
6. Be sure to read the “TROUBLESHOOTING” section
wide slot and fully insert.
regarding common operating errors before concluding
that the unit is faulty. This Class B digital apparatus complies with Canadian
ICES–003.
7. When not planning to use this unit for a long period
(ie., vacation, etc.), disconnect the AC power plug from
the wall outlet.
E-2
FEATURES
English
● This subwoofer system employs Advanced YAMAHA ● The HIGH CUT switch provides you with two positions
Active Servo Technology which YAMAHA has developed (HIGH and LOW) to adjust the tone balance between the
for reproducing higher quality super-bass sound. (Refer subwoofer and the main speakers.
to page 11 for details on Advanced YAMAHA Active ● The AUTO STANDBY switch saves you the trouble of
Servo Technology.) This super-bass sound adds a more setting the POWER switch to the ON or OFF position.
realistic, theater-in-the-home effect to your stereo
system.
● This subwoofer can be easily added to your existing
audio system by connecting to either the speaker
terminals or the line output (pin jack) terminals of the
amplifier.
PLACEMENT
Å ı Ç
E-3
CONNECTIONS
Caution: Plug in the subwoofer and other components after all connections are completed.
● All connections must be correct, that is to say L (left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also refer to the owner’s
manual for each of your components.
● The subwoofer can be connected to either the speaker output terminals or the line output (pin jack) terminals of the amplifier.
Choose one of the ways shown in this section that is more suitable for your audio system. Also, refer to the owner’s manual
of your component to be connected to the subwoofer.
POWER
ON
OFF
INPUT2 /MONO
VOLUME
STANDBY-RED 0 I0
ON-GREEN
AUTO HIGH
STANDBY
LOW
HIGH
LOW HIGH CUT
OFF
INPUT2 /MONO
INPUT1
FROM AMPLIFIER
OUTPUT
TO SPEAKERS
To AC outlet
Pin plug
cords
SUBWOOFER
(LOW PASS)
Amplifier
SPLIT SUBWOOFER
E-4
English
m Using two subwoofers
Pin plug
cords
Subwoofer Subwoofer
POWER POWER
ON ON
OFF OFF
VOLUME VOLUME
STANDBY-RED 0 I0 STANDBY-RED 0 I0
ON-GREEN ON-GREEN
SPLIT SUBWOOFER
LOW LOW
OFF OFF
INPUT1 INPUT1
FROM AMPLIFIER FROM AMPLIFIER
OUTPUT OUTPUT
TO SPEAKERS TO SPEAKERS
Amplifier
To AC outlet To AC outlet
Notes
● Some amplifiers have line output terminals labeled PRE ● When connecting to a monaural line output terminal of
OUT. When you connect the subwoofer to the PRE OUT the amplifier, connect the L/MONO INPUT2 terminal.
terminals of the amplifier, make sure that the amplifier ● When connecting to line output terminals of the amplifier,
has at least two sets of PRE OUT terminals. If the other speakers should not be connected to the OUTPUT
amplifier has only one set of PRE OUT terminals, do not terminals on the rear panel of the subwoofer. If
connect the subwoofer to the PRE OUT terminals. connected, they will not produce sound.
Instead, connect the subwoofer to the speaker output
terminals of the amplifier. (Refer to pages 6 and 7.)
E-5
Connecting to speaker output terminals of the amplifier
m Using one subwoofer
If your amplifier has only one set of main speaker output terminals
Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT
terminals of the subwoofer to the main speakers.
Subwoofer
POWER
ON
OFF
VOLUME
Speaker
STANDBY-RED
ON-GREEN
HIGH
LOW
AUTO
STANDBY
0
HIGH
LOW
I0
HIGH CUT
INPUT1
output
terminals
OFF
INPUT2 /MONO
FROM AMPLIFIER
INPUT1
FROM AMPLIFIER
OUTPUT
TO SPEAKERS
OUTPUT
TO SPEAKERS
To AC outlet
Amplifier
OFF
POWER
VOLUME
STANDBY-RED
ON-GREEN
0 I0
INPUT1
AUTO HIGH
STANDBY
HIGH
LOW
OFF
LOW
HIGH CUT FROM AMPLIFIER
INPUT2 /MONO
INPUT1
FROM AMPLIFIER
OUTPUT
TO SPEAKERS
OUTPUT
TO SPEAKERS
To AC outlet
Amplifier
A B
E-6
English
m Using two subwoofers
Connect the speaker output terminals of the amplifier to the INPUT1 terminals of the subwoofer, and connect the OUTPUT
terminals of the subwoofer to the main speakers.
Subwoofer Subwoofer
POWER
POWER
ON
ON
OFF
OFF
VOLUME
INPUT1 INPUT1 VOLUME
INPUT2 /MONO
INPUT2 /MONO
INPUT1
INPUT1 FROM AMPLIFIER
FROM AMPLIFIER
OUTPUT OUTPUT
TO SPEAKERS
OUTPUT
OUTPUT
TO SPEAKERS TO SPEAKERS TO SPEAKERS
To AC outlet To AC outlet
Amplifier
Speaker output
terminals
How to Connect:
E-7
CONTROLS AND THEIR FUNCTIONS
Rear panel
POWER
POWER
ON
1 OFF
ON
OFF
VOLUME
7
VOLUME
2 STANDBY-RED
ON-GREEN
AUTO
0 I0
8
HIGH
STANDBY
STANDBY-RED
ON-GREEN
AUTO
STANDBY
0
HIGH
I0
3 HIGH
LOW
OFF
LOW
HIGH CUT
LOW
HIGH
LOW HIGH CUT
OFF
4
INPUT2 /MONO
INPUT2 /MONO
INPUT1
FROM AMPLIFIER
OUTPUT
5
TO SPEAKERS
INPUT1
FROM AMPLIFIER
6 OUTPUT
TO SPEAKERS
Rear panel
VOLUME
POWER
ON ON
POWER
1, 4
2 OFF
OFF
STANDBY-RED
ON-GREEN
0 I0
5
AUTO HIGH
STANDBY
LOW
HIGH
LOW HIGH CUT
VOLUME OFF
STANDBY-RED 0 I0
ON-GREEN
AUTO HIGH
STANDBY
LOW
HIGH
LOW HIGH CUT
OFF
INPUT2 /MONO
INPUT2 /MONO
INPUT1
FROM AMPLIFIER
OUTPUT
TO SPEAKERS
INPUT1
FROM AMPLIFIER
OUTPUT
TO SPEAKERS
E-9
m Frequency characteristics
Fig. 1 shows the frequency characteristics of the subwoofer 100
with each position (HIGH/LOW) of the HIGH CUT switch. HIGH CUT
HIGH
90
80
HIGH CUT
70 LOW
60
50
40
20 50 100 200 500Hz
Fig. 1
Fig. 2 shows the optimum volume level with the HIGH CUT 100
70
0 I0
SW-201
60
HIGH
Main
LOW 50 speaker’s
HIGH CUT response
40
20 50 100 200 500Hz
Fig. 2
E-10
ADVANCED YAMAHA ACTIVE SERVO TECHNOLOGY
English
The theory of Yamaha Active Servo Technology has been By employing negative-impedance drive circuits, the
based upon two major factors, the Helmholtz resonator and amplifier is able to generate precise, low-amplitude, low-
negative-impedance drive. Active Servo Processing frequency waves with superior damping characteristics.
speakers reproduce the bass frequencies through an “air These waves are then radiated from the cabinet opening as
woofer”, which is a port or opening in the speaker’s cabinet. high-amplitude signals. The system can, therefore, by
This opening is used instead of, and performs the functions employing the negative-impedance output drive amplifier
of, a woofer in a conventionally designed speaker system. and a speaker cabinet with the Helmholtz resonator,
Thus, signals of low amplitude within the cabinet can, reproduce an extremely wide range of frequencies with
according to the Helmholtz resonance theory, be outputted amazing sound quality and less distortion.
from this opening as waves of great amplitude if the size of The features described above, then, are combined to be the
the opening and the volume of the cabinet are in the correct fundamental structure of the conventional Yamaha Active
proportion to satisfy a certain ratio. Servo Technology.
In order to accomplish this, moreover, the amplitudes within
the cabinet must be both precise and of sufficient power Our new Active Servo Technology — Advanced Yamaha
because these amplitudes must overcome the “load” Active Servo Technology — adopted Advanced Negative
presented by the air that exists within the cabinet. Impedance Converter (ANIC) circuits, which allows the
conventional negative impedance converter to dynamically
Thus it is this problem that is resolved through the vary in order to select an optimum value for speaker
employment of a new design in which the amplifier supplies impedance variation. With this new ANIC circuits, Advanced
special signals. If the electrical resistance of the voice coil Yamaha Active Servo Technology can provide more stable
could be reduced to zero, the movement of the speaker unit performance and improved sound pressure compared with
would become linear with respect to signal voltage. To the conventional Yamaha Active Servo Technology, resulting
accomplish this, a special negative-impedance output-drive in more natural and dynamic bass reproduction.
amplifier for subtracting output impedance of the amplifier is
used.
Air woofer
Cabinet (Helmholtz resonator)
High-amplitude
Port
bass sound
Advanced Negative-
impedance Converter
Active Servo
Processing Signals
Amplifier
E-11
TROUBLESHOOTING
Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed below or if
the instructions given below do not help, disconnect the power cord and contact your authorized YAMAHA dealer or service
center.
SPECIFICATIONS
Type .............. Active Servo Processing Subwoofer System Power Supply .......................................... AC 120 V, 60 Hz
Driver ..................... 16 cm (6-5/16”) cone woofer (JA1678) Power Consumption ................................................. 42 W
magnetic shielding type Dimensions (W x H x D) ..... 200 mm x 390 mm x 389 mm
Amplifier Output .................................................. 50 W/5Ω (7-7/8” x 15-3/8” x 15-5/16”)
High-Cut Filter ............ H: 200 Hz, L: 100 Hz (–24 dB/oct.) Weight ............................................... 9.8 kg (21 lbs. 9 oz.)
Frequency Response .................. 30 Hz–200 Hz (–10 dB)
E-12
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR, 22-34, 25462 RELLINGEN, BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VASTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA Printed in China V555480