Professional Documents
Culture Documents
Tool Drives
209
Platzhalter
für Titel
209
209 I 1
Tool Drives
Table of Contents
Contents Page
Angle grinders 61
Drum grinders 62
2 I 209
Tool Drives
The Fast Way to the Best Drive
The most important prerequisite for cost The following table provides you with an Safety regulations
effective working methods is the selection overview of suitable drives for the tools shown
of the optimal tool. After this, the choice of a in the catalogues. Read the instructions!
= (Please always observe the respec-
suitable tool drive can be made.
The following points have to be taken into Your PFERD sales advisor as well as the techni- tive valid safety regulations!)
consideration: cal customer service engineers can help you
■■Design, shape and size, find an individual solution to any specific ap-
■■speed, plication problem.
■■power output and
■■tool adapter.
Tools Catalogue 202 Catalogue 203 Catalogue 204 Catalogue 205 Catalogue 206 Catalogue 208
Drive Page
Straight grinders 7-31 ● ● ● ● ● ●
machines
powered
Angle grinders 61 - - ● ● ● ●
machines
Electric
Drum grinders 62 - - ● - - -
straight handpieces ● ● ● ● ● ●
angle handpieces ● ● ● ● ● ●
belt grinders - - ● - - -
drum grinders - - ● - - ●
PFERD catalogues 202 - 208 provide a multi- The tool drives are especially conceived for In order to find the most cost effective solution
209
tude of possibilities, allowing you to choose grinding, milling, brushing, cutting and polish- to your application problem, always choose
the best tool for your application. In order to ing. They cover all relevant speed and power the machine matching the most suitable tool.
apply these tools with optimum efficiency, output performance ranges and accord with
you need a tool drive perfectly matching the the latest requirements in ergonomics and
chosen product. safety. They are also reliable and have long
service lives.
209 I 3
Tool Drives
Comparison of the Drive Systems
Drive types
Straight grinders Straight grinders Straight grinders
Angle grinders Angle grinders Angle grinders
Belt grinders Belt grinders Belt grinders
- Drum grinders Drum grinders
Special drives - Special drives
Machine characteristics
No risk of overloading, resistant until motor Overload protection, can briefly withstand up to Overload protection, can briefly withstand up to
cuts off four times the nominal output six times the nominal output
Optimal RPM/power ratio Optimal fine tuning for use of tools possible Optimal fine tuning for use of tools possible
Good construction size to power output ratio Higher power output compared to air-powered High motor outputs, compact handpieces,
machines of the same speed efficient power transmission to the tool
Higher RPM‘s available Very speed-stable, ideal for tools that require Coverage of large speed ranges
constant speeds
Ergonomics/handling
Machine size and shape suitable for many Ergonomic machine shapes, easy-handling Light, easy-to-handle handpiece,
applications for low-fatigue work
Speed range [RPM]
3.500 - 100.000 750 - 33.000 0 - 40.000
Speed variation
Single rotation speed Stepless, electronic Stepless, electronic, alternatively using gears
Energy
Compressed air (6,3 bar) 1-phase AC 1-phase AC
3-phase AC
Power range [W]
75 - 1.000 500 - 1.530 500 - 2.700
Safety
Safe energy form, no sparking Safeguard to prevent unintentional re-starting 42 volt version suitable for protected use
Maintenance
Simple exchange of worn parts Simple exchange of carbon brushes Maintenance can be performed by qualified
technicians
PFERD repair service Technical changes electric and flexible shaft drives as well as for
PFERD provides a quick maintenance service Further technical developments and ergonomic accessories by repairing or replacing those
so that downtimes for defective machines are improvements are consistently included in parts which are defective at our discretion
kept as short as possible. Please contact your our design and manufacture. We therefore free of charge. We guarantee this entitlement
local PFERD sales service. You will receive a reserve the right to make technical changes to to replacement and repair for a maximum of
detailed quotation to aid you in making your our products. If we change our constructional 12 months unless the law states that the time
decision. If the maintenance costs exceed designs, we generally guarantee that spare limits should be longer.
70 % of the reinstatement value, you will also parts will remain available for four years after We undertake no liability for damages occur-
receive a quotation for a new machine. the change. ring within this time due to unprofessional
handling, use of other replacement parts or
Guarantee maintenance in other workshops.
Within the scope of the PFERD guarantee, we
take liability for deficiencies in air-power,
4 I 209
Air Grinders
209
209 I 5
Air Grinders
General Information
Air grinders are the “top speed“ machines They are used economically and reliably in Advantages
amongst the drives. They achieve higher series production and assembly lines. ■■Compact, ergonomic designed shape.
speeds in comparison to electric or flexible ■■Low weight.
shaft drives. They have – when measured PFERD product range
PFERD offers straight, angle and belt grinders ■■Technically up to date.
against their smaller size – a high power out- ■■High power to weight performance.
put. The robust and resistant sliding vane and as well as special drives. PFERD air grinders
are technically up to date and contain the ■■Versatile in use.
turbine motors have a long service lifetime as ■■Single speed RPM.
well as being easy to service. latest ergonomic findings and requirements.
They have been developed especially for the ■■No danger from overloading, can be
Areas of application economic application of abrasives and cutting loaded up to machine standstill.
Air grinders are very versatile. They are used tools with defined geometries and cover a ■■Housing insulated against cold and
especially in medium and large sized compa- wide range of speeds (3.500 - 100.000 RPM) vibration.
nies that have a compressed air network at and performances (75 - 1.000 watts). ■■Low-maintenance.
their disposal. ■■Easy to service.
■■Cost effective.
Criteria for selecting the optimum air grinder Operates with or without oil
The most important prerequisite for cost effec- 3. Power output Turbine and sliding vane motors are labelled as
tive work is the selection of an optimal tool. The drive unit‘s power output is the deciding follows:
After this, the choice of a suitable tool drive factor for maintaining the RPM under load.
can be made. The following points have to The load is determined from the material to be
been taken into consideration. machined, cutting capability of the tool and
the grinding pressure. Use only without oil.
1. Design, shape and size
Every type of application places a specific de- 4. Tool adapter
mand on the shape and size of the tool drive. Depending on the PFERD tool you have Operates with
The various designs can be used for many selected, different tool adapters are available or without oil.
different tasks: Depending on the dimensions, e.g. collets or threaded spindles. Every ma-
accessibility, type and frequency of the applica- chine is allocated with matching collets.
Use only with oil.
tion, the ideal drive can be selected for the Please refer to pages 94-95 for an overview of
task in hand. the collets and spindle extensions.
Advantages of oil-free compressed air
2. RPM We have explained the most important criteria
The drive should always be selected according ■■User-friendly, protecting both people and
here. Should you have any further questions, the workshop envoronment.
to the RPM and cutting speed recommenda- your PFERD sales advisor will be happy to help.
tions for the tool. Please refer to catalogues ■■Reduces operation costs, because oil and
202 - 208 for these recommendations. fittings can be dispensed with.
■■Avoids oily precipitation on the workpiece.
6 I 209
Air Grinders
Straight Grinder, Speed: 100.000 RPM / Output: 75 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PGT 1/1000 653449 front ring 0,17 3 351109 5 0,240
Collets Keys
Group 1 for shank dia. Width Quan- EAN
2,34 3 1/8 across flats tity 4007220
mm mm inch 7 mm 2 592885
EAN
196342 196359 196366
4007220
For dimensions see table page 94.
209 I 7
Air Grinders
Straight Grinder, Speed: 80.000 RPM / Output: 75 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 1/800 176658 front push-pull 0,17 3 351109 5 0,180
PGAS 1/800 176689 rear ring 0,18 3 351109 5 0,180
Collets Keys
Group 1 for shank dia. Width Quan- EAN
2,34 3 1/8 across flats tity 4007220
mm mm inch 8 mm 1 206867
EAN ø 2,5 mm 1 205013
196342 196359 196366
4007220
For dimensions see table page 94.
8 I 209
Air Grinders
Straight Grinder, Speed: 75.000 RPM / Output: 110 Watts
150
■■For fine milling, grinding and engraving
work.
■■Comes with air supply and exhaust hose.
12 20
■■Light, easy to handle.
■■Spindle bearing ensures high concentricity.
■■Rear exhaust with silencer.
20
■■Protective spindle cap can be removed for
work in narrow geometries.
9,5
If required, please order separately:
■■Complete connecting set no. 1
(see page 52). without protective spindle cap
■■In-line fine filter SFI 1/4-5
EAN 4007220809013.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PGAS 1/750 507803 rear ring 0,20 3 351109 5 0,150
Collets Keys
Group 1 for shank dia. Width Quan- EAN
2,34 3 1/8 across flats tity 4007220
mm mm inch 7 mm 2 592885
EAN
196342 196359 196366
4007220
For dimensions see table page 94.
TC burrs Mounted points Poliflex® fine grinding points Diamond grinding points
cut 3, 3 PLUS, 4, 5, head ø up to 6 mm shank ø 3 mm head ø up to 4,5 mm
ALU PLUS width up to 13 mm bond: shank ø 3 mm
head ø up to 3 mm shank ø 3 mm GHR
head ø up to 4 mm CBN grinding points
cut 1, ALU, FVK LR and TX head ø up to 5,5 mm
head ø 3 mm head ø up to 6 mm shank ø 3 mm
Please observe the recommenda-
tions on different cutting speeds
in catalogue 202.
*Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the max. specified mounted point dimensions.
209
209 I 9
Air Grinders
Straight Grinder, Speed: 70.000 RPM / Output: 220 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PGT 3/700 373248 rear push-pull 0,25 - 0,8 3 351116 8 0,390
Collets Keys
Group 4 for shank dia. Width Quan- EAN
3 6 1/8 1/4 across flats tity 4007220
mm mm inch inch 14 mm 2 206836
EAN
349311 349298 349328 349304
4007220
For dimensions see table page 94.
10 I 209
Air Grinders
Straight Grinder, Speed: 60.000 RPM / Output: 110 Watts
150
■■For fine milling, grinding and engraving
work.
■■Light, easy to handle.
12 20
■■Comes with air supply and exhaust hose.
■■Spindle bearing ensures high concentricity.
■■Rear exhaust with silencer.
20
■■Protective spindle cap can be removed for
work in narrow geometries.
9,5
If required, please order separately:
■■Complete connecting set no. 1
(see page 52). without protective spindle cap
■■In-line fine filter SFI 1/4-5
EAN 4007220809013.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PGAS 1/600 507780 rear ring 0,20 3 351109 5 0,150
Collets Keys
Group 1 for shank dia. Width Quan- EAN
2,34 3 1/8 across flats tity 4007220
mm mm inch 7 mm 2 592885
EAN
196342 196359 196366
4007220
For dimensions see table page 94.
209 I 11
Air Grinders
Straight Grinder, Speed: 50.000 RPM / Output: 200 Watts
162
31
■■High speed one-hand straight grinder.
■■For light milling and grinding work.
■■Light, easy to handle straight grinder.
■■Tool adapter shank dia. 3 or 6 mm.
32 16,5
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 3/500 S 286326 front push-pull 0,45 6 351116 8 0,370
Collets Keys
Group 5 for shank dia. Width Quan- EAN
3 6 1/8 1/4 across flats tity 4007220
mm mm inch inch 7/16“ 1 300480
EAN 9/16“ 1 186831
299944 299951 299944 606032
4007220
For dimensions see table page 94.
12 I 209
Air Grinders
Straight Grinder, Speed: 44.000 RPM / Output: 220 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 3/440 DH 176603 rear ring/lever 0,35 6 351116 8 0,340
PGZ 3/440 SU 348437 rear ring 0,35 6 351116 8 1,420
PGZ 3/440 176580 rear ring 0,35 6 351116 8 0,450
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 14 mm 1 206836
EAN 11 mm 1 206812
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
209 I 13
Air Grinders
Straight Grinder, Speed: 38.000 RPM / Output: 220 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 3/380 DH 176627 front ring/lever 0,35 6 351116 8 0,310
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 14 mm 1 206836
EAN 11 mm 1 206812
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
14 I 209
Air Grinders
Straight Grinder, Speed: 28.000 RPM / Output: 370 Watts
200
■■Silencer.
■■Comes with air supply and exhaust hose.
■■Safety lever throttle.
■■High power output.
■■Compact design.
31 38
If required, please order separately:
■■Complete connecting set no. 2
(see page 52).
■■In-line fine filter SFI 3/8-8
EAN 4007220809020.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 5/280 HV 176733 rear lever 0,6 6 351116 8 0,620
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 14 mm 1 206836
EAN 11 mm 1 206812
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 15
Air Grinders
Straight Grinder, Speed: 25.000 RPM / Output: 225 Watts
162
■■One-hand straight grinder for light milling
31
and grinding work.
■■Consistent power due to centrifugal
governor.
32 16,5
■■Compact design, easy to handle.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 3/250 S 286340 front push-pull 0,21 - 0,49 6 351116 8 0,370
Collets Keys
Group 5 for shank dia. Width Quan- EAN
3 6 1/8 1/4 across flats tity 4007220
mm mm inch inch 7/16“ 1 300480
EAN 9/16“ 1 186831
299944 299951 299944 606032
4007220
For dimensions see table page 94.
16 I 209
Air Grinders
Straight Grinder, Speed: 25.000 RPM / Output: 600 Watts
■■Silencer. 225
■■Comes with air supply and exhaust hose.
44
■■Rubber bearing, especially suitable for use
with TC burrs, reduces tooth breakage.
■■Low vibration protecting people, tools and
machine. 45 22 41
■■Extremely high stock removal.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PGAS 8/250 E-HV 600146 rear lever 0,85 6 351123 9 0,860
Collets Keys
Group 7 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 9/16“ 1 186831
EAN 3/4“ 1 186848
187074 186855 187050 187074 187067
4007220
For dimensions see table page 94.
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 17
Air Grinders
Straight Grinder, Speed: 23.000 RPM / Output 370 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 5/230 HV 235294 rear lever 0,63 6 351116 8 0,620
PG 5/230 V-HV 235300 rear lever 0,63 6 351116 8 0,840
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 14 mm 1 206836
EAN 11 mm 1 206812
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Suitable PFERD tools
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206
TC burrs Mounted points Poliflex® fine POLICAP® Diamond Cut-off wheels EHT
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm grinding points head ø up to 10 mm grinding points ø 50 mm
ALU PLUS width up to 32 mm bond: head ø up to 13 mm
head ø 6 up to 8 mm GR and PUR POLIROLL® matching
head ø up to 12 mm head ø up to 6 mm CBN arbor
cut 1, ALU, FVK GHR, LR and TX grinding points BO 6/6 0-4 or
head ø 8 up to Fan grinders head ø up to 18 mm BO 6/10 0-4
head ø up to 20 mm head ø up to 20 mm
12 mm LHR Ring wheels ER
HSS rotary cutters head ø up to 30 mm POLINOX® ring ø 40 mm
cut ALU, 1, 2, 3, 5 wheels PNER
Poliflex® wheels ø 25 mm matching
head ø up to 4 mm bond TX arbor
Please observe the ø 25 mm Felt points BO 6/6 3-10
different cutting head ø up to 8 mm
Abrasive spiral
speed recommenda- bands
tions in catalogue head ø up to 22 mm
202.
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
18 I 209
Air Grinders
Straight Grinder, Speed: 22.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 8/220 HV 450840 front lever 0,85 6 351123 9 0,950
PGAS 8/220 HV 286401 rear lever 0,85 6 351123 9 1,000
PG 8/220 V-HV 177167 front lever 0,85 6 351123 9 1,400
PGAS 8/220 V-HV 286296 rear lever 0,85 6 351123 9 1,400
Collets Keys
Group 7 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 9/16“ 1 186831
EAN 3/4“ 1 186848
187074 186855 187050 187074 187067
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206
TC burrs Mounted points Poliflex® fine Abrasive spiral Diamond Cut-off wheels EHT
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm grinding points bands grinding points ø 65 mm
ALU PLUS width up to 32 mm bond: head ø up to 22 mm head ø up to 13 mm
head ø 6 up to GR and PUR matching
10 mm head ø up to 12 mm POLICAP® CBN arbor
GHR, LR and TX head ø up to 11 mm grinding points BO 6/6 0-4 or
cut 1, ALU, FVK head ø up to 20 mm head ø up to 18 mm BO 6/10 0-4 or
head ø 10 up to Fan grinders BO 8/10 0-4
LHR head ø up to 20 mm
16 mm head ø up to 30 mm Ring wheels ER
HSS rotary cutters POLINOX® ring ø 40 mm
Poliflex wheels
®
wheels PNER
cut ALU, 1, 2, 3, 5 bond TX
head ø up to 5 mm ø 25 mm matching
ø 25 mm arbor
Please observe the Felt points BO 6/6 3-10
recommendations head ø up to 8 mm
on different cutting
speeds in catalogue
202.
209
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 19
Air Grinders
Straight Grinder, Speed: 21.000 RPM / Output: 220 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 3/210 DH 606315 front ring/lever 0,48 6 351116 8 0,430
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 14 mm 1 206836
EAN 11 mm 1 206812
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
20 I 209
Air Grinders
Straight Grinder, Speed: 20.000 RPM / Output: 900 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 10/200 V-HV 776889 rear lever 1,2 6 351123 9 1,600
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 17 mm 1 204542
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Poliflex® fine Electroplated bond Cut-off wheels EHT Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 40 mm grinding points diamond cut-off ø 50 mm knotted type
ALU PLUS width up to 50 mm bond: wheels RBG ø 70 mm
head ø 6 up to PUR ø up to 22 mm matching
10 mm head ø up to 10 mm arbor
GR Diamond BO 6/6 0-4 or
cut 1, ALU, FVK head ø up to 12 mm grinding points BO 6/10 0-4 or
head ø 10 up to TX head ø up to 18 mm BO 8/10 0-4
16 mm head ø up to 20 mm CBN Ring wheels ER
HSS rotary cutters GHR, LR grinding points ø 40 mm
cut ALU, 1, 2, 3, 5 head ø up to 25 mm head ø up to 20 mm
head ø up to 5 mm Abrasive spiral matching
bands arbor
Please observe the head ø up to 30 mm BO 6/6 3-10
recommendations POLIROLL®
on different cutting head ø up to 6 mm
speeds in catalogue Fan grinders
202. head ø up to 20 mm
POLINOX® ring
wheels PNER
ø 25 mm
209
Felt points
head ø up to 8 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 21
Air Grinders
Straight Grinder, Speed: 18.000 RPM / Output: 370 Watts
PG 5/180 V-HV
340 ■■Very slim machine extension.
144 ■■Highly robust working spindle due to
rubber bearing and robust construction.
21 38
If required, please order separately:
■■Complete connecting set no. 2
(see page 52).
■■In-line fine filter SFI 3/8-8
EAN 4007220809020.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 5/180 HV 176719 rear lever 0,3 - 0,6 6 351116 8 0,620
PG 5/180 V-HV 176726 rear lever 0,3 - 0,6 6 351116 8 0,840
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 14 mm 1 206836
EAN 11 mm 1 206812
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206
TC burrs Mounted points Poliflex® fine POLICAP® Diamond Cut-off wheels EHT
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm grinding points head ø up to 13 mm grinding points ø 50 mm
ALU PLUS width up to 32 mm bond: head ø up to 15 mm
head ø 8 up to GR and PUR POLINOX® matching
12 mm head ø up to 15 mm cross buffs CBN arbor
GHR, LR and TX head ø 25 mm grinding points BO 6/6 0-4 or
HSS rotary cutters head ø up to 25 mm head ø up to 20 mm BO 6/10 0-4 or
cut ALU, 1, 2, 3, 5 Fan grinders BO 8/10 0-4
LHR head ø up to 40 mm
head ø 2,3 up to head ø up to 30 mm
6 mm Ring wheels ER
POLISTAR ø 50 mm
Poliflex® wheels ø 20 mm
Please observe the bond TX
different cutting matching
ø 25 mm Felt points arbor
speed recommenda- head ø up to 10 mm
tions in catalogue Abrasive spiral BO 6/6 3-10
202. bands BO 8/10 6-20
head ø up to 30 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
22 I 209
Air Grinders
Straight Grinder, Speed: 18.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 9/180 V-HV 319765 rear lever 0,9 6 351123 9 1,600
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 17 mm 1 204542
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Arbors
Order No. EAN Tool mounting The arbor replaces the collet and is used for
4007220 [mm] direct adaptation of tools with a bore dia. of
10 mm.
SDD 1016 348444 ø 10 x 16 0,140
Suitable PFERD tools
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Poliflex® fine Diamond Cut-off wheels EHT Pencil brushes
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm grinding points grinding points ø 50 mm individual
ALU PLUS width up to 32 mm bond: head ø up to 15 mm filament type
head ø 8 up to GR and PUR matching PBU ø 10 up to
12 mm head ø up to 15 mm CBN arbor 12 mm
GHR, LR and TX grinding points BO 6/6 0-4 or
cut 1, ALU, FVK head ø up to 25 mm head ø up to 20 mm BO 6/10 0-4 or knotted type
head ø 16 mm LHR BO 8/10 0-4 PBG ø 19 mm
HSS rotary cutters head ø up to 30 mm Ring wheels ER Wheel brushes
cut ALU, 1, 2, 3, 5 Abrasive spiral ø 50 mm individual
head ø 2,3 up to bands filament type
6 mm head ø up to 30 mm matching RBU ø 20 up to
Fan grinders arbor 30 mm
Please observe the head ø up to 25 mm BO 6/6 3-10
different cutting POLISTAR BO 8/10 6-20
209
209 I 23
Air Grinders
Straight Grinder, Speed: 16.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 8/160 HV 536339 font lever 0,34 - 0,85 6 351123 9 0,950
PGAS 8/160 V-HV 286432 rear lever 0,34 - 0,85 6 351123 9 1,400
Collets Keys
Group 7 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 9/16“ 1 186831
EAN 3/4“ 1 186848
187074 186855 187050 187074 187067
4007220
For dimensions see table page 94.
Suitable PFERD tools
Catalogue 202 Catalogue 203*/204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Catalogue 203 POLICAP® Electroplated bond Cut-off wheels EHT Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 29 mm diamond cut-off ø 50 mm knotted type
ALU PLUS Mounted points wheels RBG ø 70 mm
head ø 8 up to head ø up to 50 mm Fan grinders ø up to 50 mm matching
16 mm width up to 50 mm head ø up to 25 mm arbor
Diamond BO 6/6 0-4 or
cut 1, ALU, FVK Catalogue 204 POLIROLL® grinding points BO 6/10 0-4 or
head ø 16 mm head ø up to 16 mm head ø up to 20 mm BO 8/10 0-4
Poliflex® fine
HSS rotary cutters grinding points POLINOX® CBN Ring wheels ER
cut ALU, 1, 2, 3, 5 bond: cross buffs grinding points ø 50 mm
head ø 2,3 up to GR and PUR head ø 25 mm head ø up to 20 mm
6 mm head ø up to 15 mm matching
GHR and TX POLISTAR arbor
Please observe the head ø up to 25 mm ø up to 20 mm BO 6/6 3-10 or
different cutting Felt points BO 8/10 6-20
speed recommenda- Poliflex® wheels
bond TX head ø up to 10 mm
tions in catalogue
202. ø 25 mm
Abrasive spiral
bands
head ø up to 30 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
24 I 209
Air Grinders
Straight Grinder, Speed: 16.000 RPM / Output: 900 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 10/160 V-HV 777282 rear lever 1,2 6 351123 9 1,600
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 17 mm 1 204542
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Arbors
Order No. EAN Tool mounting The arbor replaces the collet and is used for
4007220 [mm] direct adaptation of tools with a bore dia. of
10 mm.
SDD 1016 348444 ø 10 x 16 0,140
Suitable PFERD tools
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Poliflex® fine Electroplated bond Cut-off wheels EHT Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 50 mm grinding points diamond cut-off ø 50 mm knotted type
ALU PLUS width up to 50 mm bond: wheels RBG ø 70 mm
head ø 8 up to GR and PUR ø up to 50 mm matching
16 mm head ø up to 15 mm arbor
TX and GHR Diamond BO 6/6 0-4 or
cut 1, ALU, FVK head ø up to 25 mm grinding points BO 6/10 0-4 or
head ø 16 mm head ø up to 20 mm BO 8/10 0-4
Abrasive spiral
HSS rotary cutters bands CBN Ring wheels ER
cut ALU, 1, 2, 3, 5 head ø up to 30 mm grinding points ø 50 mm
head ø 2,3 up to head ø up to 20 mm
6 mm POLICAP® matching
head ø up to 29 mm arbor
Please observe the BO 6/6 3-10 or
different cutting Fan grinders BO 8/10 6-20
speed recommenda- head ø up to 25 mm
tions in catalogue
202. POLISTAR
ø up to 20 mm
Felt points
209
head ø up to 10 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 25
Air Grinders
Straight Grinder, Speed: 12.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 9/120 V-HV 319758 rear lever 0,4 - 0,9 6 351123 9 1,600
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 17 mm 1 204542
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Arbors
Order No. EAN Tool mounting The arbor replaces the collet and is used for
4007220 [mm] direct adaptation of tools with a bore dia. of
10 mm.
SDD 1016 348444 ø 10 x 16 0,140
Suitable PFERD tools
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
26 I 209
Air Grinders
Straight Grinder, Speed: 12.000 RPM / Output: 1.000 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 12/120 V-HV 177396 rear lever 1,3 6 351130 12 2,400
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 22 mm 1 206850
EAN 14 mm 1 206836
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Arbors Guard
Order No. EAN Tool mounting Order No. EAN Supported
4007220 [mm] 4007220 dia.
[mm]
SDM 14 x 20 MF 179291 ø 14/22,23 x 20 0,184
H 35-125S 179307 125 0,360
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Abrasive spiral Electroplated bond Cut-off wheels EHT Pencil brushes
cut 3, 3 PLUS, 4, 5, All mounted points bands diamond cut-off ø 76 mm, individual
ALU PLUS from the standard head ø up to 45 mm wheels without guard filament type
head ø 10 up to range head ø up to ø up to 50 mm ø 50 mm PBU ø 10 up to
20 mm 50 mm Fan grinders 20 mm
head up to 40 mm Diamond matching
cut 1, ALU, FVK grinding points arbor knotted type
head ø 16 mm POLINOX ring®
head ø up to 20 mm BO 6/6 0-4 or PBG ø 19 mm
wheels PNER BO 6/10 0-4 or
HSS rotary cutters ø 50 mm CBN BO 8/10 0-4 Wheel brushes
cut ALU, 1, 2, 3, 5 grinding points individual
head ø 3,2 up to POLIROLL ®
head ø up to 20 mm Ring wheels ER filament type
8 mm head ø up to 12 mm ø 70 mm, RBU ø 20 up to
without guard 40 mm
Please observe the ø 50 mm
different cutting knotted type
speed recommenda- matching RBG ø 70 mm
tions in catalogue arbor
209
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 27
Air Grinders
Straight Grinder, Speed: 10.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 8/100 HV 536438 front lever 0,17 - 0,85 6 351123 9 0,950
PGAS 8/100 HV 286272 rear lever 0,17 - 0,85 6 351123 9 1,000
PG 8/100 V-HV 176825 front lever 0,17 - 0,85 6 351123 9 1,400
PGAS 8/100 V-HV 286289 rear lever 0,17 - 0,85 6 351123 9 1,400
Collets Keys
Group 7 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 9/16“ 1 186831
EAN 3/4“ 1 186848
187074 186855 187050 187074 187067
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 206 Catalogue 208
TC burrs Mounted points Poliflex® fine Fan grinders Cut-off wheels EHT Pencil brushes
cut 3, 3 PLUS, 4, 5, head ø up to 50 mm grinding points head ø up to 40 mm ø 50 mm individual
ALU PLUS width up to 40 mm bond: filament type
head ø 10 up to GR and PUR Felt points matching PBU ø 12 up to
20 mm head ø up to 25 mm head ø up to 20 mm arbor 30 mm
GHR, LR and TX BO 6/6 0-4 or
HSS rotary cutters POLIROLL® BO 6/10 0-4 or encapsulated
head ø up to 40 mm head ø up to 18 mm
cut ALU, 1, 2, 3, 5 LHR BO 8/10 0-4 PBV ø 22 up to
head ø 3,2 up to head ø up to 40 mm POLINOX® 30 mm
10 mm Ring wheels ER
mounted points ø 50 mm knotted type
Poliflex® wheels head ø up to 50 mm
Please observe the bond TX PBG ø 25 mm
different cutting matching
ø 40 mm POLINOX® ring arbor Wheel brushes
speed recommenda- wheels PNER
tions in catalogue Abrasive spiral BO 6/6 3-10 or individual
ø 50 mm BO 8/10 4-8 or filament type
202. bands
head ø up to 60 mm POLINOX® BO 8/10 6-20 RBU ø 50 up to
cross buffs 70 mm
POLICAP® head ø 25 mm
head ø up to 21 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
28 I 209
Air Grinders
Straight Grinder, Speed: 7.000 RPM / Output: 1.000 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 12/70 V-HV 177419 rear lever 1,3 6 351130 12 2,400
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 22 mm 1 206850
EAN 14 mm 1 206836
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Arbors Guard
Order No. EAN Tool mounting Order No. EAN Supported
4007220 [mm] 4007220 dia.
[mm]
SDM 14 x 20 MF 179291 ø 14/22,23 x 20 0,184
H 35-125S 179307 125 0,360
209 I 29
Air Grinders
Straight Grinder, Speed: 5.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 8/50 V-HV 176788 front lever 0,42 - 0,85 6 351123 9 1,600
Collets Keys
Group 7 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 9/16“ 1 186831
EAN 3/4“ 1 186848
187074 186855 187050 187074 187067
4007220
For dimensions see table page 94.
HSS rotary cutters All Poliflex® fine grinding points Electroplated bond diamond cut-off
cut ALU, 1, 2, 3, 5 and Poliflex® fine grinding wheels wheels
head ø 5,0 up to 16 mm ø up to 50 mm ø up to 50 mm
HSS aluminium cutters Abrasive spiral bands matching
119 head ø up to 50 mm arbor
120 BO 6/6 0-4 or
Fan grinders BO 6/10 0-4
Arbor with thread head ø up to 50 mm
BO 6/10 and BO 8/10
for HSS rotary cutters POLINOX® mounted points
head ø up to 50 mm
Please observe the recommendations on dif-
ferent cutting speeds in catalogue 202. POLINOX® cross buffs
head ø 38 mm
POLICLEAN® wheels/mounted points
ø 50 mm
Felt points and felt wheels
ø up to 45 mm
matching
arbor
BO 6/6 3-10
Note: Where no shank diameter is indicated, *Catalogue 204: The information given here refers to an open shank length of 10 mm and the
the shank diameter specification is 6 mm. max. specified mounted point dimensions.
30 I 209
Air Grinders
Straight Grinder, Speed: 4.000 RPM / Output: 900 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PG 10/40 V-HV 802649 rear lever 1,2 6 351123 9 1,700
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 17 mm 1 204542
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Arbors
Order No. EAN Tool mounting The arbor replaces the collet and is used for
4007220 [mm] direct adaptation of tools with a bore dia. of
10 mm.
SDD 1016 348444 ø 10 x 16 0,140
HSS rotary cutters All Poliflex® fine grinding points Electroplated bond diamond cut-off
cut ALU, 1, 2, 3, 5 and Poliflex® fine grinding wheels wheels
head ø 6,0 up to 16 mm ø up to 50 mm ø 50 mm
HSS aluminium cutters Abrasive spiral bands matching
119 head ø up to 50 mm arbor
120 BO 6/6 0-4 or
Fan grinders BO 6/10 0-4
Arbor with thread head ø up to 50 mm
BO 6/10 and BO 8/10
for HSS rotary cutters POLINOX® mounted points
head ø up to 50 mm
Please observe the recommendations on dif-
ferent cutting speeds in catalogue 202. POLICLEAN® wheels
ø 50 and 75 mm
Felt points and felt wheels
209
ø up to 45 mm
matching arbor BO 6/6 3-10
Note: Where no shank diameter is indicated, *Catalogue 204: The information given here refers to an open shank length of 10 mm and the
the shank diameter specification is 6 mm. max. specified mounted point dimensions.
209 I 31
Air Grinders
Angle Grinder, Speed: 80.000 RPM / Output: 75 Watts
173
■■Adjustable side exhaust.
■■Silencer.
■■Smallest, high speed angle grinder in this
20
performance class for industrial applica-
39
tions.
■■Robust, without angular gear.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PWS 1/800 176900 rear push-pull 0,18 3 351109 5 0,115
Collets Keys
Group 2 for shank dia. Width Quan- EAN
2,34 3 3/32 1/8 across flats tity 4007220
mm mm inch inch 6 mm 1 204504
EAN 8 mm 1 206867
207864 207840 207864 207857
4007220
For dimensions see table page 94.
32 I 209
Air Grinders
Angle Grinder, Speed: 25.000 RPM / Output: 110 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PWSA 1/250 802588 rear ring 0,2 3 351109 5 0,225
Collets Keys
Group 3 for shank dia. Width Quan- EAN
3 3/32 1/8 across flats tity 4007220
mm inch inch 10 mm 1 188514
EAN 3/16“ 1 188279
188262 188378 188354
4007220
For dimensions see table page 94.
Arbors
Order No. EAN Use for The arbor replaces the collet.
4007220 It is used for direct mounting from
ATADISC® or COMBIDISC® tools.
ATADISC® tools, SP 20, ST 25, ST 35,
ASD 20 AD 178805 0,005
AD 2005, AD 3505-2
ASD 20 CD COMBIDISC® tools, SBH 20, SBH 25,
308417 0,005
1/4-20 G SBH 38, CD 20, CD 38
209 I 33
Air Grinders
Angle Grinder, Speed: 21.000 RPM / Output: 370 Watts
■■Silencer.
■■Comes with air supply and exhaust hose.
38
63 ■■Safety lever throttle.
■■Low angle head height.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PWS 5/210 HV 177075 rear lever 0,60 6 351116 8 0,710
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 11 mm 1 206812
EAN 17 mm 1 204542
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Using this conversion set, cut-off and rein- and tighten the grinding wheel with the
Grinding wheel adapter set forced ring wheels can be used up to dia. clamping screw (washer is not needed for disc
50 mm and at strengths of 1 - 9 mm. Simple widths from 6 mm).
handling: Remove the collet, connect the hand
protection, place the washer onto the spindle
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206
TC burrs Mounted points Poliflex® fine Fan grinders Diamond Cut-off wheels EHT
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm grinding points head ø up to 20 mm grinding points ø 50 mm
ALU PLUS width up to 32 mm bond: head ø up to 12 mm
head ø 6 up to GR and PUR POLINOX® ring matching
12 mm head ø up to 12 mm wheels PNER CBN arbor
GHR, LR and TX ø 25 mm grinding points BO 6/6 0-4 or
cut 1, ALU, FVK head ø up to 20 mm head ø up to 18 mm BO 6/10 0-4 or
head ø 10 up to ATADISC® abrasive BO 8/10 0-4
LHR ø up to 30 mm disc holder
16 mm
Abrasive spiral SHT 3550 with Ring wheels ER
HSS rotary cutters bands abrasive disc ø 50 mm
cut ALU, 1, 2, 3, 5 head ø up to 22 mm AD 5005
head ø up to 5 mm matching
POLICAP ® COMBIDISC® arbor
Please observe the head ø up to 11 mm abrasive discs BO 6/6 3-10 or
different cutting ø 20 up to 38 mm BO 8/10 6-20
speed recommenda-
tions in catalogue
202.
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
34 I 209
Air Grinders
Angle Grinder, Speed: 20.000 RPM / Output: 220 Watts
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PWS 3/200 DH 282175 front ring/lever 0,35 6 351116 8 0,370
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 11 mm 1 206812
EAN 14 mm 1 206836
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
209 I 35
Air Grinders
Angle Grinder, Speed: 20.000 RPM / Output: 300 Watts
150
■■Slim angle head for work in confined
places.
■■High speed stability power output.
■■Easy to handle, compact shape.
■■Angular gear with long service lifetime.
37 ■■High spindle concentricity.
■■Safety lever throttle protects against inad-
69
vertent start-up.
■■Comes with air supply und exhaust hose.
Order No. EAN Exhaust Throttle Air Incl. Air supply hose Connect. set
4007220 direction type consumption collet inner dia. EAN
[m³/min] dia. [mm] [mm] 4007220
PWSA 4/200 HV 598184 rear lever 0,57 6 8 351116 0,520
Collets Keys
Group 5 for shank dia. Width Quan- EAN
3 6 1/8 1/4 across flats tity 4007220
mm mm inch inch 7/16“ 1 300480
EAN 9/16“ 1 186831
299944 299951 299944 606032
4007220
For dimensions see table page 94.
36 I 209
Air Grinders
Angle Grinder, Speed: 17.000 RPM / Output: 370 Watts
Order No. EAN Exhaust Throttle Air Incl. Air supply hose Connect. set
4007220 direction type consumption collet inner dia. EAN
[m³/min] dia. [mm] [mm] 4007220
PWS 5/170-45 HV 484999 rear lever 0,63 6 8 351116 0,880
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 11 mm 1 206812
EAN 17 mm 1 204542
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Suitable PFERD tools
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 206 Catalogue 208
TC burrs Mounted points Poliflex® Cut-off wheels EHT Pencil brushes
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm fine grinding points ø 50 mm individual filament type
ALU PLUS width up to 32 mm bond: PBU ø 10 up to 12 mm
head ø 8 up to 12 mm GR and PUR matching
head ø up to 12 mm arbor knotted type
HSS rotary cutters GHR, LR and TX BO 6/6 0-4 or PBG ø 19 mm
cut ALU, 1, 2, 3, 5 head ø up to 20 mm BO 6/10 0-4 or
head ø up to 6 mm BO 8/10 0-4 Wheel brushes
LHR individual filament type
Please observe the differ- head ø up to 30 mm Grinding wheels ER RBU ø 20 up to 30 mm
ent cutting speed recom- Poliflex® wheels ø 50 mm
mendations in catalogue bond TX
202. matching
ø 25 mm arbor
Abrasive spiral bands BO 6/6 3-10 or
head ø up to 30 mm BO 8/10 6-20
POLICAP®
head ø up to 13 mm
Fan grinders
head ø up to 25 mm
209
Felt points
head ø up to 10 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 37
Air Grinders
Angle Grinder, Speed: 16.000 RPM / Output: 370 Watts
Order No. EAN Exhaust Throttle Air Incl. Air supply hose Connect. set
4007220 direction type consumption collet inner dia. EAN
[m³/min] dia. [mm] [mm] 4007220
PWS 5/160 HV 235287 rear lever 0,63 6 8 351116 0,710
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 11 mm 1 206812
EAN 17 mm 1 204542
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Using this conversion set, cut-off and rein- spindle and tighten the grinding disc with the
Grinding wheel adapter set forced ring wheels can be used up to dia. clamping screw (washer is not needed for disc
50 mm and at strengths of 1 - 9 mm. Simple widths from 6 mm).
handling: Remove the collet, connect the
hand protection, place the washer onto the
Note: Where no shank diameter is indicated, *Catalogue 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
38 I 209
Air Grinders
Angle Grinder, Speed: 13.000 RPM / Output: 370 Watts
– Workplace-friendly
– No oil precipitation onto the tool
– No negative effects on oil-sensitive mate- 36
Adapter set
rials e.g. ceramic, wood, plastic. SAS 10/50
Order No. EAN Exhaust Throttle Air Incl. Air supply hose Connect. set
4007220 direction type consumption collet inner dia. EAN
[m³/min] dia. [mm] [mm] 4007220
PWS 5/130 HV 271766 rear lever 0,3 - 0,6 6 8 351116 0,710
Collets Keys
Group 6 for shank dia. Width Quan- EAN
3 6 8 3/32 1/8 1/4 across flats tity 4007220
mm mm mm inch inch inch 11 mm 1 206812
EAN 17 mm 1 204542
212875 212851 212936 234969 212882 212868
4007220
For dimensions see table page 94.
Using this conversion set, cut-off and rein- spindle and tighten the grinding disc with the
forced ring wheels can be used up to dia. clamping screw (washer is not needed for disc Grinding wheel adapter set
50 mm and at strengths of 1 - 9 mm. Simple widths from 6 mm).
handling: Remove the collet, connect the
hand protection, place the washer onto the
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 39
Air Grinders
Angle Grinder, Speed: 12.000 RPM / Output: 220 Watts
146
■■For grinding and finishing work in con-
nection with all COMBIDISC® tools (use a
backing pad without shank).
■■Easy to handle, compact shape.
■■Flat angle head for work in confined
31 places.
■■High torque.
36 ■■Safety ring lever throttle (DH) protects
against inadvertent start-up.
44
If required, please order separately:
■■Complete connecting set no. 2
(see page 52).
■■In-line fine filter SFI 3/8-8
EAN 4007220809020.
Order No. EAN Exhaust Throttle Air Drive Air supply hose Connect. set
4007220 direction type consumption spindle inner dia. EAN
[m³/min] thread [mm] 4007220
PW 3/120 DH 271780 front ring/lever 0,35 1/4‘‘ - 20 UNC 8 351116 0,390
Keys
Width Quan- EAN
across flats tity 4007220
11 mm 1 206812
40 I 209
Air Grinders
Angle Grinder, Speed: 12.000 RPM / Output: 600 Watts
Order No. EAN Exhaust Throttle Air Air supply hose Connect. set Drive Tool
4007220 direction type consumption inner dia. EAN spindle mounting
[m³/min] [mm] 4007220 thread [mm]
PW 9/120 HV 319772 rear lever 0,9 9 351123 M14 22,23 1,750
COMBICLICK® fibre disc and Electroplated bond Cut-off and Cup brushes
fibre disc diamond cut-off wheels grinding wheels individual filament type
ø up to 115 mm ø up to 115 mm TBU ø 60 up to 75 mm M14
POLIFAN® flap discs
Backing pad for COMBICLICK® Flaring cup brushes
fibre disc and fibre disc Diamond cut-off wheels individual filament type
ø up to 115 mm ø up to 115 mm KBU ø 100 up to 115 mm M14
CC - GT 115/125
GT 115
209
209 I 41
Air Grinders
Angle Grinder, Speed: 12.000 RPM / Output: 900 Watts
PW 11/120 AVH
■■With anti-vibration handle and autobal-
ancer for adjusting imbalance.
■■Tool adapter: Special flange, only suitable
for cut-off and grinding wheels!
Order No. EAN Exhaust Throttle Air Air supply hose Connect. set Drive Tool
4007220 direction type consumption inner dia. EAN spindle mounting
[m³/min] [mm] 4007220 thread [mm]
PW 11/120 HV 447970 front bottom lever 1,13 12 351130 M14 22,23 1,900
PW 11/120 AVH 447963 front bottom lever 1,13 12 351130 special 22,23 2,000
Only for type PW 11/120 HV Electroplated bond Cut-off and grinding wheels Only for PW 11/120 HV
diamond cut-off wheels
Fibre discs ø up to 125 mm POLIFAN® flap discs Wheel brushes
ø up to 125 mm knotted type
Diamond cut-off wheels RBG ø 115 mm
Backing pad for fibre discs bore ø 22,2 mm
available on request ø up to 125 mm
42 I 209
Air Grinders
Angle Grinder, Speed: 12.000 RPM / Output: 1.000 Watts
Order No. EAN Exhaust Throttle Air Air supply hose Connect. set Drive Tool
4007220 direction type consumption inner dia. EAN spindle mounting
[m³/min] [mm] 4007220 thread [mm]
PW 12/120 HV 177334 rear lever 1,3 12 351130 M14 22,23 2,500
knotted type
KBG ø 115 mm M14
209 I 43
Air Grinders
Angle Grinder, Speed: 3.500 RPM / Output: 300 Watts
180
■■Slim angle head for work in confined
places.
■■Easy to handle, compact shape.
■■Angular gear with long service life.
■■Comes with air supply and exhaust hose.
38 ■■For grinding and finishing work with all
COMBIDISC® tools.
69 ■■Safety lever throttle (HV) protects against
inadvertent start-up.
Order No. EAN Exhaust Throttle Air Incl. Connect. set Air supply hose
4007220 direction type consumption collet EAN inner dia.
[m³/min] dia. [mm] 4007220 [mm]
PWS 4/40 HV 626221 rear lever 0,57 6 351116 8 0,700
Collets Keys
Group 5 for shank dia. Width Quan- EAN
3 6 1/8 1/4 across flats tity 4007220
mm mm inch inch 7/16“ 1 300480
EAN 9/16“ 1 186831
299944 299951 299944 606032
4007220
For dimensions see table page 94.
All Poliflex® fine grinding Poliflex® marbling tool COMBIDISC® SBH 75 COMBIDISC® felt discs
points and Poliflex® fine PFZY 5040 ø up to 75 mm
grinding wheels COMBIDISC®
ø up to 80 mm Felt points and felt wheels diamond abrasive discs COMBIDISC® POLICLEAN® discs
ø up to 45 mm systems CD and CDR ø up to 75 mm
ø up to 75 mm
COMBIDISC® brush
COMBIDISC® non-woven discs ø 50 mm
ø up to 75 mm
44 I 209
Air Grinders
Belt Grinder, Belt Length: 305 x 3 - 12 mm
Order No. EAN Exhaust Throttle Air Belt speed Power Air supply hose Connect. set
4007220 direction type consumption [m/s] output inner dia. EAN
[m³/min] [watts] [mm] 4007220
PBS 3/200 DH 99 801857 front ring/lever 0,35 21 220 8 351116 0,575
BSVAK 9/25
8.8
BSVAK 9/9
ø9
8.8
ø 25
BSVAK 9/16
ø16
■■Robust steel design. ■■Belt arm guide can be fixed. Ordering note:
■■Use of the full roller width possible. ■■BSVA 9/25-1 with conical guide roller (range Please refer to catalogue 204 for detailed
■■Extremely slim fixing lugs on the facing 1 mm). information and ordering data regarding abra-
roller. ■■Belt length 305 mm. sive and non-woven belts.
■■Asymmetrical arms for flush grinding.
209 I 45
Air Grinders
Belt Grinder, Belt Length: 520/610 mm x Width 3 - 20 mm
Order No. EAN Exhaust Throttle Air Belt Power out- Air supply hose Connect. set
4007220 direction type consumption speed put inner dia. EAN
[m³/min] [m/s] [watts] [mm] 4007220
PBSA 5/130 HV 925 801970 rear lever 0,3-0,6 20 370 8 351116 1,250
PBSA 5/160 HV 925 801963 rear lever 0,63 20-25 370 8 351116 1,250
PBSA 5/210 HV 925 801956 rear lever 0,60 31 370 8 351116 1,250
PBSA 9/120 HV 925 802632 rear lever 0,90 16 600 9 351123 1,870
3.8
Belt grinder attachment arms BSVA 4/16
ø 16
8.8
BSAD 41/36 x 610 BSVA 9/16
ø 16
8.8
11.5
ø 25
8.8
18
ø 23
■■Robust steel design. ■■Belt arm guide can be fixed. Ordering note:
■■Use of the full roller width possible. ■■BSVA 9/25-1 with conical guide roller (range Please refer to catalogue 204 for detailed
■■Extremely slim fixing lugs on the facing 1 mm). information and ordering data regarding abra-
roller. ■■Belt length 520 mm or with adapter sive and non-woven belts.
■■Asymmetrical arms for flush grinding. 610 mm.
46 I 209
Air Grinders
Belt Grinder, Belt Length: 480/610 mm x Width 6 - 25 mm
Order No. Incl. EAN Exhaust Throttle Air Belt Power Air supply hose Connect. set
belt 4007220 direction type consumption speed output inner dia. EAN
arm [m³/min] [m/s] [watts] [mm] 4007220
PBS 5/155 HV 824 1 792674 side lever 0,6 21 370 8 351116 1,390
PBS 5/155 HV 1924 2 792681 side lever 0,6 21 370 8 351116 1,390
PBS 5/155 HV 2324 3 792698 side lever 0,6 21 370 8 351116 1,390
8
4
ø 24
BSVA 5/155-8/24x480
ø 16
BSVA 5/155-4/16x610
19
ø 24
BSVA 5/155-19/24x480
9
ø 16
BSVA 5/155-23/24x480
ø 24
209 I 47
Air Grinders
Air Motors for Rigid Extensions, Handpieces
Order No. EAN RPM Power Air Connection Air supply hose Suitable
4007220 output consumption coupling inner dia. extension
[watts] [m³/min] [DIN] [mm]
PM 5/230 HV 263235 23.000 370 0,63 10 8 STV 20, STV 27 0,650
Keys
Width Quan- EAN
across flats tity 4007220
ø 4 mm 2 205020
Rigid extensions
Rigid extensions
for air motors
for air-power motors Combined with air motors, the ideal solution
STV 20 for tough applications e.g. during cleaning
or milling work on large hard-to-reach work-
pieces in foundries.
STV 27 In series production, rigid extensions are
frequently used. They are adapted exactly to
Example of the workpiece geometries.
bent extension Other lengths and bend radii are available on
request.
Order No. EAN Connection Handpiece Dia. x length Bending Suitable matching arbors
4007220 coupling coupling [mm] radius
[DIN] [G] [mm]
STV 20 L 200 272770 10 16/22 20 x 200 150 incl. 4 ZGA STV 20 0,400
STV 20 L 400 179604 10 16/22 20 x 400 150 incl. 4 ZGA STV 20 0,630
STV 20 L 600 179703 10 16/22 20 x 600 150 incl. 4 ZGA STV 20 0,890
STV 27 L 250 282137 10 22 27 x 250 250 7 ZGA, WZ 7 B STV, WZ 7-45° STV 0,550
STV 27 L 500 179499 10 22 27 x 500 250 7 ZGA, WZ 7 B STV, WZ 7-45° STV 0,930
Handpieces
Order No. EAN Handpiece Max. speed Dia. x length Transmis- Collet Incl.
4007220 coupling [RPM] [mm] sion group collet
[G] ratio dia. [mm]
4 ZGA STV 20 247952 16/22 25.000 20 x 110 - 11 6 0,165
7 ZGA 181928 22 25.000 27 x 130 - 11 6 0,320
WZ 7 B STV 334645 22 17.100 55 x 157 1,3 : 1 6 6 0,710
WZ 7-45° STV 334614 22 17.100 57 x 175 1,3 : 1 6 6 0,750
48 I 209
Air Grinders
Air Motors for Rigid Extensions, Handpieces
Order No. EAN RPM Power Air Connection Air supply hose Suitable
4007220 output consumption coupling inner dia. extension
[watts] [m³/min] [DIN] [mm]
PM 12/200 HV 178058 20.000 1.000 1,3 10 12 STV 33 2,160
PM 12/120 HV 178034 12.000 1.000 1,3 10 12 STV 33 2,160
PM 12/70 HV 358122 7.000 1.000 1,3 10 12 STV 33 2,320
Keys
Width Quan- EAN
across flats tity 4007220
ø 4 mm 2 205020
Rigid extensions
Rigid extensions
for air motors
Combined with air motors, the ideal solution for air-power motors
for tough applications e.g. during cleaning
or milling work on large hard-to-reach work- STV 33
pieces in foundries.
In series production, rigid extensions are Example of
frequently used. They are adapted exactly to bent extension
the workpiece geometries.
Other lengths and bend radii are available on
request.
Order No. EAN Connection Handpiece Dia. x Bending Suitable matching arbors
4007220 coupling coupling length radius
[DIN] [G] [mm] [mm]
STV 33 L 250 179420 10 28 33 x 250 300 10 ZGE, WZ 10 B STV, WZ 10 45° STV, 12 ZGA 1,025
STV 33 L 500 179468 10 28 33 x 500 300 10 ZGE, WZ 10 B STV, WZ 10 45° STV, 12 ZGA 2,100
STV 33 L 1000 179758 10 28 33 x 1000 300 10 ZGE, WZ 10 B STV, WZ 10 45° STV, 12 ZGA 3,250
Handpieces
Order No. EAN Handpiece Max. speed Dia. x length Transmis- Collet Incl.
4007220 coupling [RPM] [mm] sion group collet
[G] ratio dia. [mm]
209
209 I 49
Air Grinders
Special Machines, Filing Machine, Marking Pen
220
28 ■■Comes with air supply and exhaust hose.
■■For machining deep slots.
20 11 28 ■■Keys are included in delivery.
Order No. EAN Throttle Exhaust Air Air supply hose Frequency Stoke Hose
4007220 type direction consumption inner dia. [strokes/min] length length
[m³/min] [mm] (linerar) [mm] [mm]
PFG 07/220 657638 ring rear 0,046 4 22.000 0,7 1.500 0,180
Order No. EAN Needle Throttle Exhaust Air Air supply Frequency Hose Opera-
4007220 gauge type direction consump- hose [strokes/min] length tion
tion inner dia. [mm] pressure
[m³/min] [mm] [bar]
MST 31 F 450314 fine ring front 0,030 4 30.000 - 36.000 2.000 6 - 7 0,150
MST 31 M 450079 medium ring front 0,030 4 30.000 - 36.000 2.000 6 - 7 0,150
MST 31 G 450307 coarse ring front 0,030 4 30.000 - 36.000 2.000 6 - 7 0,150
50 I 209
Air Grinders
Valves, Fittings, Hoses and Consumables
How to choose the correct connection fittings for your air-power machine
In general, PFERD air grinders with “rear Many accessory parts fit to several machines, Connection sets
exhaust“ are supplied with air supply and ex- they have been sorted into the groups 1-5. The complete connection set nos. 1-4 for the
haust hose. Air grinders with “front exhaust“ Please refer to the tables for the order number individual air grinders are allocated in the table
are generally supplied with fixed screw-on of the matching accessory parts. below. Please refer to the table on page 52 to
nozzles, matching the required inner dia. find out the connection set contents.
compressed air hose.
Cata- Tool drive Application Air con- Exhaust air Inside hose Comes with air supply Coupling Machine
logue with without sumption dia. [mm] and exhaust hose set group
page [m³/min] front rear page 52
oil oil
7 PGT 1/1000 l 0,17 l 5 Air supply hose 1 1
8 PG 1/800 l 0,17 l 5 - 1 1
8 PGAS 1/800 l 0,18 l 5 Air supply and exhaust hose 1 1
9 PGAS 1/750 l 0,2 l 5 Air supply and exhaust hose 1 1
10 PGT 3/700 l l 0,25 - 0,8 ■ l 8 Air supply and exhaust hose 2 5
11 PGAS 1/600 l 0,2 l 5 Air supply and exhaust hose 1 1
12 PG 3/500 S l 0,45 l 8 - 2 5
13 PG 3/440 DH l 0,35 ■ l 8 Air supply and exhaust hose 2 5
13 PGZ 3/440 SU l 0,35 ■ l 8 Air supply and exhaust hose 2 5
13 PGZ 3/440 l 0,35 ■ l 8 Air supply and exhaust hose 2 5
14 PG 3/380 DH l 0,35 l 8 - 2 5
15 PG 5/280 HV l 0,6 ■ l 8 Air supply and exhaust hose 2 5
16 PG 3/250 S l 0,21 - 0,49 l 8 - 2 5
17 PGAS 8/250 E-HV l 0,85 ■ l 9 Air supply and exhaust hose 2 2
18 PG 5/230 HV l l 0,63 ■ l 8 Air supply and exhaust hose 2 5
18 PG 5/230 V-HV l l 0,63 ■ l 8 Air supply and exhaust hose 2 5
19 PG 8/220 HV l 0,85 l 9 - 3 2
19 PGAS 8/220 HV l 0,85 l 9 - 3 2
19 PG 8/220 V-HV l 0,85 l 9 - 3 2
19 PGAS 8/220 V-HV l 0,85 l 9 - 3 2
20 PG 3/210 DH l 0,48 l 8 - 2 5
21 PG 10/200 V-HV l 1,2 l 9 Air supply and exhaust hose 3 2
22 PG 5/180 HV l 0,3 - 0,6 ■ l 8 Air supply and exhaust hose 2 5
22 PG 5/180 V-HV l 0,3 - 0,6 ■ l 8 Air supply and exhaust hose 2 5
23 PG 9/180 V-HV l l 0,9 ■ l 9 Air supply and exhaust hose 3 2
24 PG 8/160 HV l 0,85 l 9 - 3 2
24 PGAS 8/160 V-HV l 0,85 ■ l 9 Air supply and exhaust hose 3 2
25 PG 10/160 V-HV l 1,2 l 9 Air supply and exhaust hose 3 2
26 PG 9/120 V-HV l l 0,3 - 0,6 ■ l 9 Air supply and exhaust hose 3 2
27 PG 12/120 V-HV l 1,3 ■ l 12 Air supply and exhaust hose 4 4
28 PG 8/100 HV l 0,17 - 0,85 l 9 - 3 2
28 PGAS 8/100 HV l 0,17 - 0,85 ■ l 9 Air supply and exhaust hose 3 2
28 PG 8/100 V-HV l 0,17 - 0,85 l 9 - 3 2
28 PGAS 8/100 V-HV l 0,17 - 0,85 ■ l 9 Air supply and exhaust hose 3 2
29 PG 12/70 V-HV l 1,3 ■ l 12 Air supply and exhaust hose 4 4
30 PG 8/50 V-HV l 0,42 - 0,71 l 9 - 3 2
31 PG 10/40 V-HV l 1,2 ■ l 9 Air supply and exhaust hose 3 2
32 PWS 1/800 l 0,18 ■ l 5 - 1 1
33 PWSA 1/250 l 0,27 ■ l 5 Air supply and exhaust hose 1 3
34 PWS 5/210 HV l 0,6 ■ l 8 Air supply and exhaust hose 2 5
35 PWS 3/200 DH l 0,35 l 8 - 2 5
36 PWSA 4/200 HV l 0,57 l 9 Air supply and exhaust hose 3 5
37 PWS 5/170-45 HV l l 0,63 ■ l 8 Air supply and exhaust hose 2 5
38 PWS 5/160 HV l l 0,63 ■ l 8 Air supply and exhaust hose 2 5
39 PWS 5/130 HV l l 0,3 - 0,6 ■ l 8 Air supply and exhaust hose 2 5
40 PW 3/120 DH l 0,35 l 8 - 2 5
41 PW 9/120 HV l l 0,9 ■ l 9 Air supply and exhaust hose 3 2
42 PW 11/120 HV, PW 11/120 AVH l 1,13 l 12 - 4 4
43 PW 12/120 HV l 1,3 ■ l 12 Air supply and exhaust hose 4 4
44 PWS 4/40 HV l 0,57 ■ l 9 Air supply and exhaust hose 3 5
46 PBSA 5/210 HV 925 l 0,6 l 9 Air supply and exhaust hose 2 5
45 PBS 3/200 DH 99 l 0,35 l 8 - 2 5
46 PBSA 5/160 HV 925 l l 0,63 l 8 Air supply and exhaust hose 2 5
47 PBS 5/155 HV 924 l 0,6 l 8 - 2 5
47 PBS 5/155 HV 1924 l 0,6 l 8 - 2 5
47 PBS 5/155 HV 2424 l 0,6 l 8 - 2 5
46 PBSA 5/130 HV 925 l 0,3 - 0,6 l 8 Air supply and exhaust hose 2 5
46 PBSA 9/120 HV l 1,3 l 12 Air supply and exhaust hose 4 4
50 MST 31 l 0,025 - 0,03 l 4 Air supply hose 1 3
50 PFG 07/220 l 0,046 ■ l 4 Air supply hose 1 1
48 Air motor PM 5/230 HV 0,63 8 Air supply and exhaust hose 2 5
209
l ■ l
49 Air motor PM 12/200 HV l 1,3 - 1,6 ■ l 12 Air supply and exhaust hose 4 4
49 Air motor PM 12/120 HV l 0,6 - 1,3 ■ l 12 Air supply and exhaust hose 4 4
49 Air motor PM 12/70 HV l 0,6 - 1,3 ■ l 12 Air supply and exhaust hose 4 4
209 I 51
Air Grinders
Valves, Fittings, Hoses and Consumables
The fittings required to connect your air-powered machine are shown in the table below.
Fast coupling system 8
Connection of
max. 5 m 1 compressed
air network
Machine side 1 4
6
5
7
2 3 10
9
Safety cou- 4.1
pling system
Machine group Fast coupling system EAN Connecting set no. Safety coupling system EAN
Order no. and dimensions 4007220 Order no. 4007220
➊ ➋ ➌ ➍ ➎ 1 2 3 4
Pos. 1 Hose nozzle (is supplied with the machine)
l TG 6 1/8 ø 6 / R 1/8“ 178362
l TG 8 1/4 ø 8 / R 1/4“ 178379
l TG 9 1/4 ø 9 / R 1/4“ 178409
Pos. 2: Threaded quick coupling Pos. 2
l STG 1/8 R 1/8“ male 178300
l l STG 1/4 R 1/4“ male 178324 STG 1/4 ST 801888
Pos. 2.1
l l DSTG 1/4 ST (Ball joint) 801895
Pos. 3: Quick-coupling (self-closing) with nipple Pos. 3.1
l VKT 6 ø6 178195 SVKT 6 801925
l VKT 8 ø8 178201 SVKT 8 801932
l VKT 9 ø9 178218 SVKT 9 801949
Pos. 4: Air hoses
l PLS 5 ø 5 / sold by metre 178461
l PLS 6 ø 6 / sold by metre 178478 3m
l PLS 8 ø 8 / sold by metre 178485 3m
l PLS 9 ø 9 / sold by metre 178492 3m
l PLS 12 ø 12 / sold by metre 178508 3m
Air hose for particularly-heavy duty service: please enquire.
Pos. 4.1 In-line fine filter (pore size: 5 µm)
l l SFI 1/4 - 5 for PLS 5 809013
l SFI 3/8 - 8 for PLS 8 809020
l SFI 3/8 - 9 for PLS 9 809044
l SFI 1/2 - 12 for PLS 12 809051
Pos. 5: Nipples for quick coupling Pos. 5.1
l T4 for MST 31 179208
l T5 PWS 1/250 179390
l T6 ø6 178331 1* T6 ST 801796
l T8 ø8 178522 1* T8 ST 801840
l T9 ø9 178386 1* T9 ST 801819
l T 12 NW 12 ø 12 178423 1*
Pos. 6: Quick-couplings (self-closing) with male thread Pos. 6.1
l l l VKA 1/4 R 1/4“ male 178232 1* SVKA 1/4 801901
l l l l VKA 1/2 R 1/2“ male 178256 1* 1* SVKA 1/2 801918
l VKA 1/2 NW 12 R 1/2“ male also for ONG A 1/2 178249 1*
Pos. 7: Quick-couplings (self-closing) with female thread
l l l l VKI 1/4 R 1/4“ female 178270
l l l l VKI 1/2 R 1/2“ female 178287
Pos. 8: Complete maintenance units
l l ONG-A 1/4 R 1/4“ female 801741 1*
■ l l l ONG-A 1/2 R 1/2“ female 801765 1* 1* 1*
l l l l Special lubricating oil, 1 litre see page 97 179338 1* 1* 1* 1*
l l l l Special lubricating oil, 5 litres see page 97 179321
Pos. 9: Lubricators, loose
l l OE-A 1/4 R 1/4“ female 801772
l l l OE-A 1/2 R 1/2“ female 801789
Pos. 10: Hose clamps
l K 9 for PLS 5 178539
l l K 13 for PLS 6 + 8 178546 2* 2*
l K 16 for PLS 9 178553 2*
l K 20 for PLS 12 204801 2*
l = Matching accessories, ø = The information refers to the inside dia. of the air hose in [mm] * units per set
52 I 209
Electric Grinders and Accessories
209
209 I 53
Electric Grinders and Accessories
General Information
Standards, safety,
Large knurled, general information
Compact housing for easy-to-lower handle
low noise levels RPM control for longer life PFERD electric machines bear
■■the CE symbol,
■■are totally insulated and comply with
protective class II.
PFERD electric machines comply with
■■the EC Machinery Directive,
■■EC Low-Voltage Directive and
■■Electromagnetic Compatibility.
National regulations must be
Non-slip High motor output Lockable observed.
rubber grip on/off switch
54 I 209
Electric Grinders and Accessories
Electric Straight Grinder, Speed: 33.000 RPM / Output: 1.050 Watts
Special Features
UGER 11/330 SI
■■Particularly suitable for milling and grind-
ing work with tungsten carbide burrs and
mounted points.
380
■■Totally insulated.
155
■■High power output straight grinder with
stepless speed adjustment.
■■Smooth start up for the protection of 41 68
people, tools and machine.
■■Digital electronic speed control.
■■Electronic overload switch-off, restart
protection on power failure.
■■Robust, comfortable ergonomic design.
■■Optimum machine guidance due to long
spindle housing.
Collets Keys
Group 8 for shank dia. Width Quan- EAN
6 8 10 1/4 3/8 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 18 mm 1 206843
213674 213704 213711 213681 213728
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Poliflex® fine Electroplated bond Cut-off wheels EHT Pencil brushes
cut 3, 3 PLUS, 4, 5, head ø 10 up to grinding points diamond cut-off ø 50 up to 55 mm individual
ALU PLUS 50 mm head ø 8 up to wheels without protective filament type
head ø 4 up to width up to 70 mm 40 mm ø 22 up to 40 mm cover PBU ø 10 up to
16 mm without protective 12 mm
Abrasive spiral cover Ring wheels ER
cut 1, ALU, FVK bands ø 50 up to 55 mm knotted type
head ø 6 up to head ø 4 up to Diamond without protective PBG ø 19 mm
16 mm 38 mm grinding points cover
head ø 9 up to Wheel brushes
HSS rotary cutters POLICAP® 25 mm matching individual
cut ALU, 1, 2, 3, 5 head ø 7 up to arbor filament type
head ø up to 3,2 mm 13 mm CBN BO 6/6 0-4 or RBU ø 20 up to
grinding points BO 6/10 0-4 or 30 mm
Please observe the POLIROLL /®
head ø 12 up to BO 8/10 0-4
different cutting POLICO® 20 mm knotted type
speed recommenda- head ø 6 up to Only set the max. RBG ø 70 mm
tions in catalogue 12 mm permissible speed per
202. tool dia.
Fan grinders
head ø 15 up to
25 mm
POLISTAR
ø up to 20 mm
209
Felt points
head ø 6 up to
12 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 55
Electric Grinders and Accessories
Electric Straight Grinder, Speed: 25.000 RPM / Output: 500 Watts
Special Features
UGER 5/250 SI
■■Totally insulated.
■■Stepless RPM adjustment.
325 ■■Easy-operation due to side switch.
120 ■■High power output, extremely easy to
handle machine.
32
■■Digital electronic ensures a consistent RPM,
57
even under load.
■■Smooth start up for the protection of
people, tools and machine.
■■Electronic switch-off on extreme overload,
restart protection on power failure.
■■Robust, easy to service construction.
Collets Keys
Group 11 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 18 mm 1 206843
196236 196281 196304 196335 196328
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Abrasive spiral Electroplated bond Cut-off wheels Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 50 mm bands diamond cut-off ø 50 up to 55 mm individual
ALU PLUS width up to 70 mm head ø up to 50 mm wheels without protective filament type
head ø 6 up to ø up to 50 mm cover RBU ø 20 up to
20 mm POLICAP® without protective 30 mm
head ø up to 16 mm cover matching
cut 1, ALU, FVK arbor knotted type
head ø 6 up to POLIROLL® matching BO 6/6 0-4 RBG ø 70 mm
16 mm head ø up to 15 mm arbor
BO 6/6 0-4 Ring wheels ER
HSS rotary cutters Fan grinders ø 50 up to 55 mm
cut ALU, 1, 2, 3, 5 head ø up to 30 mm Diamond without protective
head ø up to 4 mm POLISTAR grinding points cover
ø up to 20 mm head ø 6 up to
Please observe the 25 mm matching
different cutting Poliflex® arbor
speed recommenda- head ø 8 up to CBN BO 6/6 3-10
tions in catalogue 15 mm grinding points
202. head ø from 12 mm Only set the max.
POLINOX® permissible speed per
cross buffs tool dia.
head ø up to 38 mm
Felt points
head ø up to 15 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
56 I 209
Electric Grinders and Accessories
Electric Straight Grinder, Speed: 15.000 RPM / Output: 1.530 Watts
Special Features
UGER 15/150 SI
■■Ideal for heavy milling and grinding work.
■■Totally insulated. 495
■■High power output straight grinder with 135
stepless RPM adjustment.
■■Smooth start up for the protection of
42
people, tools and machine. 75
■■Digital electronic for constant RPM.
■■Electronic switch-off on overload, restart
protection on power failure.
■■High torque ensures excellent speed stabil-
ity.
Collets Keys
Group 12 for shank dia. Width Quan- EAN
6 8 10 12 1/4 across flats tity 4007220
mm mm mm mm inch 22 mm 2 206850
EAN
195994 196014 196038 196045 196052
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
TC burrs Mounted points Abrasive spiral Diamond Cut-off wheels EHT Pencil brushes
cut 3, 3 PLUS, 4, 5, head ø 50 mm bands grinding points ø 50 up to 55 mm individual
ALU PLUS width up to 70 mm head ø 30 up to head ø from 10 mm without guard filament type
head ø 12 up to 75 mm PBU ø 10 up to
20 mm CBN matching 30 mm
Fan grinders grinding points arbor
HSS rotary cutters head ø 25 up to head ø from 20 mm BO 6/6 0-4 or knotted type
cut ALU, 1, 2, 3, 5 50 mm BO 6/10 0-4 or PBG ø 19 up to
head ø 5 up to 7 mm BO 8/10 0-4 25 mm
POLINOX®-
Please observe the mounted points Ring wheels ER Wheel brushes
different cutting head ø up to 40 mm ø 50 up to 55 mm individual
speed recommenda- without guard filament type
tions in catalogue POLICLEAN® RBU ø 20 up to
202. tools matching 70 mm
ø up to 50 mm arbor
BO 6/6 3-10 or knotted type
POLIROLL® BO 8/10 6-20 RBG ø 70 up to
head ø up to 18 mm 100 mm
Only set the max.
permissible speed per encapsulated
tool dia. RBV ø 63 mm
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209
209 I 57
Electric Grinders and Accessories
Electric Straight Grinder, Speed: 9.000 RPM / Output: 500 Watts
Special Features
UGER 5/90 SI
■■Totally insulated.
■■Stepless RPM adjustment.
■■Easy-operation due to side switch.
■■High power output, extremely easy to
346
handle machine.
105
■■Digital electronic ensures a constant RPM
even under load.
32 57 ■■Smooth start up for the protection of
people, tools and machine.
■■Electronic switch-off on extreme overload,
restart protection on power failure.
■■Robust, easy to service construction.
■■Especially suitable for POLINOX®/
POLIVLIES® tools.
Collets Keys
Group 11 for shank dia. Width Quan- EAN
3 6 8 1/8 1/4 across flats tity 4007220
mm mm mm inch inch 14 mm 1 206836
EAN 18 mm 1 206843
196236 196281 196304 196335 196328
4007220
For dimensions see table page 94.
POLINOX® set 2 fan grinders and 10 POLINOX® mounted
POLINOX® set
PNL/Z/R 6050 UGER 5/90 230 V points in various designs and grit sizes.
Contents:
1 electric straight grinder UGER 5/90 SI Please refer to catalogue 204 for detailed
with electronic RPM adjustment information and ordering data regarding the
(range 4.000 - 9.000 RPM), POLINOX® set.
power 500 watts.
58 I 209
Electric Grinders and Accessories
Electric Straight Grinder, Speed: 5.900 RPM / Output: 1.530 Watts
Special Features
UGER 15/60 SI
■■For heavy milling and grinding work.
■■Totally insulated.
■■Stepless RPM adjustment. 495
■■Digital electronic for a constant RPM. 135
■■High torque.
■■Electronic switch-off on overload, restart 42
75
protection on power failure.
■■Smooth start up for the protection of
people, tools and machine.
Collets Keys
Group 12 for shank dia. Width Quan- EAN
6 8 10 12 1/4 across flats tity 4007220
mm mm mm mm inch 22 mm 2 206850
EAN
195994 196014 196038 196045 196052
4007220
For dimensions see table page 94.
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 208
HSS rotary cutters Mounted points Abrasive spiral POLINOX® Electroplated bond Wheel brushes
cut ALU, 1, 2, 3, 5 Head ø 50 mm bands mounted points diamond cut-off individual
head ø 10 up to Width up to 40 mm head ø 75 up to head ø 50 up to wheels filament type
16 mm 100 mm 100 mm ø 40 up to 55 mm RBU ø 80 up to
without guard 100 mm
Please observe the Fan grinders POLINOX® RBU ø 100 up to
different cutting head ø 60 up to ring wheels 125 mm
speed recommenda- 80 mm PNER bore ø 14 mm
tions in catalogue ø 75 up to 100 mm RBU ø 150 mm
202. Flap wheels
ø 100 POLICLEAN® bore ø 22,2 mm
ø 150 up to 200 mm mounted points RBU ø 100 mm
width 30 mm head ø up to bore ø 12 mm
209
Note: Where no shank diameter is indicated, *Catalogues 203/204: The information given here refers to an open shank length of 10 mm and
the shank diameter specification is 6 mm. the max. specified mounted point dimensions.
209 I 59
Electric Grinders and Accessories
Electric Straight Grinder, Speed: 3.000 RPM / Output: 1.530 Watts
Special Features
UGER 15/30 SI
■■Totally insulated.
495
■■Stepless RPM adjustment.
135 ■■Digital electronic for a constant RPM.
■■Electronic switch-off on overload, restart
protection on power failure.
42 ■■High torque ensures excellent speed
75
stability.
■■Ideal for finishing work on surfaces with
larger grinding tools.
■■Smooth start up for the protection of
people, tools and machine.
Collets Keys
Group 12 for shank dia. Width Quan- EAN
6 8 10 12 1/4 across flats tity 4007220
mm mm mm mm inch 22 mm 2 206850
EAN
195994 196014 196038 196045 196052
4007220
For dimensions see table page 94.
HSS rotary cutters Flap wheels POLICLEAN® discs Electroplated bond Cup brushes
cut ALU, 1, 2, 3, 5 ø 150 up to 165 mm ø 100 up to 150 mm diamond cut-off wheels individual filament type
head ø 16 mm ø 50 up to 55 mm TBU ø 60 mm
POLINOX® Cloth rings without guard
Please observe the differ- mounted points ø 125 up to 150 mm Wheel brushes
ent cutting speed recom- head ø 100 mm individual filament type
mendations in catalogue POLIFLAP®
RBU ø 100 mm
202. POLINOX® ring wheels ø 170 mm
ø 150 mm RBU ø 150 mm
bore ø 22,2 mm
RBU ø 150 mm
bore ø 12 mm
matching
arbor
BO 8/12-22,2 5-18
Note: Where no shank diameter is indicated,
the shank diameter specification is 6 mm.
60 I 209
Electric Grinders and Accessories
Electric Angle Grinder, Speed: 20.000 RPM / Output: 500 Watts
Special Features
UWER 5/200 SI
■■Tool mount 1/4“-20 UNC 265
thread, max. tool dia. up to 55 mm.
■■Totally insulated.
■■Stepless RPM adjustment.
■■Especially for COMBIDISC® tools (with 72 57
backing pad without threaded shank).
■■Digital electronic for constant RPM.
■■High torque, easy handling. 1/4“ - 20 UNC
209 I 61
Electric Grinders and Accessories
Drum Grinder, Speed: 3.500 RPM / Output: 1.530 Watts
Special features
UWER 15/40 SI D19
■■Totally insulated.
■■Low speed angle grinder/burnisher with
440 stepless RPM adjustment.
■■Digital electronic for constant RPM even
under load.
■■Electronic switch-off on overload, restart
protection on power failure.
■■Smooth start up for the protection of
people, tools and machine.
75 ■■Spindle lock for easy tool change.
■■Drive spindle with two keyways for in-
creased force transmission.
Keys
Width Quan- EAN
across flats tity 4007220
13 mm 1 206829
62 I 209
Electric Grinders and Accessories
Belt Grinder, Belt Length 520/610 mm x Width 3 - 20 mm
Special features
UBS 5/100 SI 925
■■Incl. belt grinder attachment arm BSVA
9/25. 470
■■Totally insulated.
■■Stepless RPM adjustment.
57
■■High power output, easy to handle shape. 95
■■Digital electronic for constant RPM even
under load.
■■Electronic switch-off on overload, restart
protection on power failure.
■■Robust, easy to service construction. pivotable
■■The medium-sized belt grinder attachment belt grinder attachment
is pivotable on the machine and allows BSVH 41 (see p. 96)
flexible adaptation to individual working with BSVA 9/25 x 520
situations.
■■Easy, quick belt change due to spring
clamp.
8.8
BSAD 41/36 x 610 BSVA 9/16
ø 16
8.8
11.5
ø 25
8.8
18
ø 23
■■Robust steel arms. ■■Belt arm guide can be fixed. Ordering note:
■■Use of the full roller width possible. ■■BSVA 9/25-1 with conical guide roller Please refer to catalogue 204 for detailed
■■Extremely slim fixing lugs on the facing (width 1 mm). information and ordering data regarding abra-
roller. ■■Belt length 520 mm or with adapter sive and non-woven belts.
■■Asymmetrical arms for flush sideways 610 mm.
grinding.
209 I 63
Electric Grinders and Accessories
Electric Pipe Belt Grinder, Output: 1.050 Watts, Belt Length: 610 mm
Special features
UBS 11/90 SI-R
■■Totally insulated.
■■Stepless RPM adjustment.
530
■■Digital electronic for constant RPM even
300 under load.
■■Electronic switch-off on overload, restart
protection on power failure.
■■ Start up is current-limited for smooth start up.
■■Robust, easy to service construction.
165
68 ■■Easy to handle grinding on variable (pipe)
radii due to single-lever system.
■■Adjustable belt guide roller for adaptation
to pipe diameters up to 70 mm.
■■Wrap angle on workpiece possible up to
maximum 220 degrees.
■■Please refer to catalogue 204 for detailed
information and ordering data regarding
abrasive non-woven short belts.
Keys
Width Quan- EAN
across flats tity 4007220
4 mm (Allen) 1 204450
Electric Pipe Belt Grinder, Output: 500 Watts, Belt Length: 533 mm
Special features
UBS 5/70 SI-R
■■Totally insulated.
■■Stepless RPM adjustment.
440 ■■Digital electronic for constant RPM even
250 under load.
■■Electronic switch-off on overload, restart
protection on power failure.
■■ Start up current limiting for smooth start up.
57 ■■Easy to handle grinding on variable (pipe)
140
radii due to single-lever system.
■■Adjustable belt guide roller for adaptation
to pipe diameters up to 55 mm.
■■Wrap angle on workpiece up to maximum
180 degrees.
■■Please refer to catalogue 204 for detailed
information and ordering data regarding
abrasive and non-woven short belts.
Keys
Width Quan- EAN
across flats tity 4007220
4 mm (Allen) 1 204450
64 I 209
Flexible Shaft Drives and Accessories
209
209 I 65
Flexible Shaft Drives and Accessories
General Information
Flexible shaft drives are multiple speed The PFERD product range Advantages
machines. They cover a wide RPM range PFERD offers various types of flexible shaft ■■Extremely compact and ergonomic
and can be adjusted steplessly electronically drives as well as a comprehensive range of handpieces.
or over gears to match individual tool require- matching flexible shafts, handpieces, angle ■■Extremely low-weight handpieces.
ments. Flexible shaft drives have an extremely drives, drum and special drives. ■■Extremely robust drives designed for per-
high power output. They can also be used PFERD flexible shaft drives and their acces- manent operation.
with the compact handpieces or extensions for sories are extremely robust, technically up ■■Technically up to date.
work in hard-to-reach places. to date and are built according to the latest ■■Extremely high power output.
ergonomic knowledge and specifications. This ■■Extremely versatile.
Applications programme was developed especially for the
Flexible shaft drives can be used for almost all ■■Simple power supply.
economic use of grinding, milling, brushing, ■■Low-maintenance.
jobs. They are used successfully in many indus- cut-off and polishing tools and cover a wide
trial sectors for different processes. The RPM ■■Easy to service.
range of speeds (0 - 40.000 RPM) and outputs ■■Cost effective.
adjustment allows the use of various tools on (500 - 2.700 watts).
one single machine.
66 I 209
Flexible Shaft Drives and Accessories
General Information
Flexible shaft
➌ Catalogue page 81 83 81 85 87 89 91
RPM 24.000 - 40.000 10.000 - 25.000 10.000 - 25.000 12.000 - 25.000 750 - 18.000 850 - 12.000 850 - 10.000
➍ output [watts] 300 - 500 700 - 1.400 750 - 1.500 880 - 1.760 140 - 2.450 525 - 6.280 525 - 6.280
Connection on
➎ - motor side DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10
- handpiece side G 16 DPF/SRF G 16 G 22 G 28 G 28 G 35
➏ Suitability m l l l m m –
Drive motor Mammoth Electronic ME/MEW + ST 103
max. 40.000 RPM max. 24.000 RPM max. 40.000 RPM max. 25.000 RPM max. 18.000 RPM max. 18.000 RPM
Power output 2.200/1.500 watts
12 ZGA 12 ZGA
Speed 12.000 - 24.000 RPM
WZ 4 A WZ 4 A
max. 18.000 RPM max. 17.100 RPM max. 17.100 RPM max. 17.100 RPM
Angle
WT 7 E M 14
max. 25.000 RPM
209 I 67
Flexible Shaft Drives and Accessories
Flexible Shafts and Handpieces
Connection on
- motor side DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10
- handpiece side G 16 DPF / SRF G 16 G 22 G 28 G 28 G 35
Suitability l l l m – – –
handpieces
Straight
WZ 4 A WZ 6 WZ 4 A WZ 7 45°
handpieces
max. 20.000 RPM max. 18.000 RPM max. 20.000 RPM max. 17.100 RPM
Angle
WZT 6 90°/45° WZ 7 B
max. 18.000 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability m m m l m – –
handpieces
Straight
WZ 4 A WZ 6 WZ 4 A WZ 7 45° WZ 10 45°
handpieces
max. 20.000 RPM max. 18.000 RPM max. 20.000 RPM max. 17.100 RPM max. 17.100 RPM
Angle
WZT 6 90°/45° WZ 7 B WZ 10 B
max. 18.000 RPM max. 17.100 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability – – – m l l m
handpieces
max. 25.000 RPM max. 18.000 RPM max. 18.000 RPM max. 10.000 RPM
Speed 3.000 / 6.000 / 12.000 RPM
12 ZGA 12 ZGA 12 ZG
Drive motor RUER 19/120 SI
WZ 7 B WZ 10 B WZ 10 B
max. 17.100 RPM max. 17.100 RPM max. 17.100 RPM
WT 10 H WT 10 H
max. 8.500 RPM max. 8.500 RPM
attachments
Other
68 I 209
Flexible Shaft Drives and Accessories
Multi-Speed Machines RUER/RUG
Record-universal motor RUER 5/250 SI ■■Pipe stand protects the machine in any
■■Totally insulated. position. RUER 5/250 SI
■■Stepless RPM adjustment. ■■Electronic switch-off on overload, restart
■■Digital electronic ensures constant RPM, protection on power failure.
even under load.
■■Versatile use, as it can be connected to any Dimensions L x W x H:
230 volt AC current line or to 230 volt, 285 x 57 x 102 mm
50/60 Hz generator.
■■High power output for fine milling, grinding Ordering note:
and polishing work. The machine is delivered without a flexible
■■Due to the light and slim handpieces, easy shaft. Please order separately.
handling is possible. Machine with foot switch available on request.
■■Start up current limiting for smooth start up.
Record universal motor RUER 10/250 SI ■■Start up current limiting for smooth start up.
■■Totally insulated. ■■Pipe stand protects the machine in any RUER 10/250 SI
■■Stepless RPM adjustment. position.
■■Digital electronic ensures constant RPM ■■Electronic switch-off on overload, restart
even under load. protection on power failure.
■■Versatile use, as it can be connected to any
230 volt AC current line or to 230 volt, Dimensions L x W x H:
50/60 Hz generator. 300 x 75 x 140 mm
■■High performance for milling, grinding and
polishing work. Ordering note:
■■The drive motor can be used in tool and The machine is delivered without a flexible
mould construction, in precision engineer- shaft. Please order separately.
ing and in the DIY and hobby sectors.
209 I 69
Flexible Shaft Drives and Accessories
Flexible Shafts and Handpieces
Connection on
- motor side DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10
- handpiece side G 16 DPF / SRF G 16 G 22 G 28 G 28 G 35
Suitability l l l l – – –
handpieces
Straight
WZ 4 A WZ 6 WZ 4 A WZ 7 45°
handpieces
max. 20.000 RPM max. 18.000 RPM max. 20.000 RPM max. 17.100 RPM
Angle
WZT 6 90°/45° WZ 7 B
max. 18.000 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability m l l m – – –
handpieces
Straight
max. 40.000 RPM max. 24.000 RPM max. 40.000 RPM max. 25.000 RPM
Power output 600/800 watts
Speed 6.000 - 12.000 RPM
WZ 4 A WZ 6 WZ 4 A WZ 7 45°
handpieces
max. 20.000 RPM max. 18.000 RPM max. 20.000 RPM max. 17.100 RPM
Angle
WZT 6 90°/45° WZ 7 B
max. 18.000 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability – m m m – – –
handpieces
Straight
6Z 4 ZGB 7 ZGA
Drive motor RUER 8/180 SI, MMEW 11/120
WZ 6 WZ 4 A
handpieces
WZ 7 45°
max. 18.000 RPM max. 20.000 RPM
Angle
WZT 6 90°/45° WZ 7 B
max. 18.000 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
For detailed information and ordering data on flexible shafts and l Ideally suitable m Suitable – Not suitable
handpieces please refer to the stated catalogue pages.
70 I 209
Flexible Shaft Drives and Accessories
Multi-Speed Machines RUER/MMEW
Record universal motor RUER 8/180 SI ■■The combi-speed control KDR 8/180 SI can
Incl. combi-speed control KDR 8/180 SI be used as a table-top or foot control. In RUER 8/180 SI
■■For general use in milling, grinding and table-top operation, the RPM can be con-
polishing work. trolled individually using the potentiometer.
■■Totally insulated. For foot-controlled operation, the maximum
■■Stepless RPM adjustment. speed can be preset using the potentiom-
■■RPM adjustment possible on running motor. eter. Control then takes place using the foot
■■Extremely low noise development. pedal.
■■Good RPM/power output ratio. Only use with Motor RUER 8/180 SI.
■■Particularly suitable for use in tool and
mould construction. Ordering note:
The machine is delivered without a flexible
shaft. Please order separately.
The table stand TS L 1400 with screw clamp Handpiece support TSA L 1400
can be attached to bench tops of up to 65 This support matches the table stand and al- Accessories for tool drives RUER
mm in thickness. lows you to optimally place various handpieces
The telescopic system allows indiviudal height ready for use.
adjustment up to maximum 140 cm.
Max.10 kg carrying capacity. Ordering note:
Please order support separately.
TSA L 1400
TS L 1400
209 I 71
Flexible Shaft Drives and Accessories
Flexible Shafts and Handpieces
Connection on
- motor side DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10
- handpiece side G 16 DPF / SRF G 16 G 22 G 28 G 28 G 35
Suitability l l l l – – –
handpieces
Straight
handpieces
WZ 4 A WZ 4 A
Angle
WT 7 E M 14
max. 25.000 RPM
Suitability – m m m l – –
handpieces
max. 24.000 RPM max. 40.000 RPM max. 25.000 RPM max. 18.000 RPM
RPM 4.200 / 6.300 / 9.000 / 11.000 RPM
12 ZGA
max. 18.000 RPM
Drive motor Quint QD 05
WZ 6 WZ 4 A WZ 7 45° WZ 10 45°
handpieces
max. 18.000 RPM max. 20.000 RPM max. 17.100 RPM max. 17.100 RPM
Angle
WZ 7 B WZ 10 B
WZT 6 90°/45° max. 17.100 RPM max. 17.100 RPM
max. 18.000 RPM
attachments
Suitability – – – – l – –
handpieces
10 ZGE
Straight
12 ZGA
max. 18.000 RPM
Drive motor Quint QD 05
handpieces
WZ 10 45°
Angle
WZ 10 B
max. 17.100 RPM
attachments
BSG 3/10/40
max. 5.000 RPM
For detailed information and ordering data on flexible shafts and l Ideally suitable m Suitable – Not suitable
handpieces please refer to the stated catalogue pages.
72 I 209
Flexible Shaft Drives and Accessories
Multi-Speed Machine Quint and Accessories
Recommended use:
Grinding and polishing tools dia. ≥ 80 mm are
not suitable for use with the Quint. Do not
use with angle drive WT 10 H.
The overdrive ST 103 transmits the drive speed Drive speeds with Quint QD 05
in a ratio of 1:3. 2.250 RPM Overdrive ST 103 DIN 10
Drive core included in delivery. 4.200 RPM
9.000 RPM
Please refer to page 93 for detailed informa- 18.900 RPM
tion regarding the ST 103. 33.000 RPM
209 I 73
Flexible Shaft Drives and Accessories
Flexible Shafts and Handpieces
Connection on
- motor side DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10
- handpiece side G 16 DPF / SRF G 16 G 22 G 28 G 28 G 35
Suitability l m m m – – –
Drive motor Mammoth Electronic ME/MEW
handpieces
Straight
max. 40.000 RPM max. 24.000 RPM max. 40.000 RPM max. 25.000 RPM
Power output 2.200/1.500 watts
handpieces
Angle
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability m l l l m m –
Drive motor Mammoth Electronic ME/MEW + ST 103
handpieces
10 ZGE 10 ZGE
Straight
12 ZGA 12 ZGA
Speed 12.000 - 24.000 RPM
max. 20.000 RPM max. 18.000 RPM max. 20.000 RPM max. 17.100 RPM max. 17.100 RPM max. 17.100 RPM
Angle
WZT 6 90°/45° WZ 7 B WZ 10 B WZ 10 B
max. 18.000 RPM max. 17.100 RPM max. 17.100 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability – – – m l l m
handpieces
max. 25.000 RPM max. 18.000 RPM max. 18.000 RPM max. 10.000 RPM
Drive motor Mammoth Electronic ME/MEW
12 ZGA 12 ZGA 12 ZG
max. 18.000 RPM max. 18.000 RPM max. 10.000 RPM
Power output 2.200/1.500 watts
Speed 500 - 12.000 RPM
handpieces
WZ 7 B WZ 10 B WZ 10 B
max. 17.100 RPM max. 17.100 RPM max. 17.100 RPM
attachments
74 I 209
Flexible Shaft Drives and Accessories
Multi-Speed Machine Mammoth Electronic and Accessories
The Mammoth Electronic can be used for ■■Restart protection on power failure.
diverse milling, grinding and polishing work. ■■Easy to service, housing with 4 easy to ME 22/150
remove modules. MEW 18/150
Special features
■■Stepless speed adjustment (with overdrive Ordering note:
ST 103 up to max. 36.000 RPM). ME 22/150 = 3-phase AC current
■■Removable operating console with possibil- MEW 18/150 = 1-phase AC current
ity for extension, e.g. hanging design, work
in boilers. The drive motors are supplied without plugs
■■Smooth start up. and flexible shafts.
■■Quick and easy RPM adjustment possible on
running motor.
■■High torque, even in the lower RPM range.
■■Extremely low noise development due to
vibration damper.
■■Automatic motor stop on overload.
Please refer to page 93 for detailed informa- Drive speed n max. = 12.000 RPM
tion regarding the ST 103.
209
Replacement core
209 I 75
Flexible Shaft Drives and Accessories
Flexible Shafts and Handpieces
Connection on
- motor side DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10 DIN 10
- handpiece side G 16 DPF / SRF G 16 G 22 G 28 G 28 G 35
Suitability ● ● ● ● ❍ – –
Drive motor Mammoth Electronic MD 10 + ST 103
handpieces
Straight
RPM 12.000 / 17.100 / 24.000 / 36.000 RPM
WZ 6 WZ 7 45° WZ 10 45°
handpieces
WZT 6 90°/45° WZ 7 B WZ 10 B
max. 18.000 RPM max. 17.100 RPM max. 17.100 RPM
attach-
ments
Other
WT 7 E M 14
max. 25.000 RPM
Suitability – ❍ ❍ ❍ ● ● ●
handpieces
6Z 4 ZGB 7 ZGA
Speed 4.800 / 5.700 / 6.300 / 8.000 / 9.600 RPM
12 ZGA 12 ZGA 12 ZG
Drive motor Mammoth MD 10
handpieces
WZT 6 90°/45° WZ 7 B WZ 10 B WZ 10 B
max. 18.000 RPM max. 17.100 RPM max. 17.100 RPM max. 17.100 RPM
attachments
12 ZGA 12 ZGA 12 ZG
max. 18.000 RPM max. 18.000 RPM max. 10.000 RPM
Power output 736 watts
handpieces
WZ 10 45° WZ 10 45°
Angle
WZ 10 B WZ 10 B
max. 17.100 RPM max. 17.100 RPM
attachments
76 I 209
Flexible Shaft Drives and Accessories
Multi-Speed Machine Mammoth and Accessories
Drive speeds with Mammoth Drive speed n max. = 12.000 RPM Replacement core
2.550 RPM
209 I 77
Flexible Shaft Drives and Accessories
Flexible Shafts and Handpieces
Connection on
- motor side DIN 15 DIN 15 DIN 15 DIN 15
- handpiece side G 28 G 28 G 35 G 35
Suitability ● ● – –
handpieces
Straight
handpieces
Angle
WZ 10 45° WZ 10 B WZ 10 45° WZ 10 B
max. max. max. max.
17.100 RPM 17.100 RPM 17.100 RPM 17.100 RPM
attach-
ments
Other
Suitability ❍ ● ● ●
handpieces
Straight
handpieces
Angle
WZ 10 45° WZ 10 B WZ 10 45° WZ 10 B
max. max. max. max.
17.100 RPM 17.100 RPM 17.100 RPM 17.100 RPM
attachments
BSG 3/10/40
BSG 3/10/40 BSG 10/35 max. 5.000 RPM BSG 10/35
Other
handpieces
Angle
WZ 10 45° WZ 10 B WZ 10 45° WZ 10 B
max. max. max. max.
17.100 RPM 17.100 RPM 17.100 RPM 17.100 RPM
attachments
BSG 3/10/40
BSG 3/10/40 BSG 10/35 max. 5.000 RPM BSG 10/35
Other
78 I 209
Flexible Shaft Drives and Accessories
Multi-Speed Machine Master Grinder and Accessories
Drive speeds:
1.000, 1.700, 2.700, 5.100, 7.300,
13.500 RPM.
Dimensions L x W x H:
480 x 185/340 x 430
Ordering note:
If the required voltage is not specified,
we supply the 3-phase AC current motor
switched to 400 volt. Master Grinder in design
3-phase AC current 230 volt available on
request. Other voltage from 42 up to 440 volt
and 60 Hz are available on request, subject to
an extra charge.
The drive motors are supplied without plug
and flexible shaft.
209
209 I 79
Flexible Shaft Drives and Accessories
Flexible Shafts
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206/208
outputs
RPM
TC burrs Mounted points Poliflex® Abrasive spiral bands Diamond Cut-off wheels EHT
cut 3, 3 PLUS, 4, 5, head ø up to 13 mm fine grinding points head ø up to 15 mm grinding points ø 50 mm
ALU PLUS width up to 13 mm shank ø 3 + 6 mm head ø up to 8 mm matching
head ø 4 to 6 mm shank ø 3 mm bond: POLICAP® shank ø 3 + 6 mm arbor
GR and PUR head ø 7 mm BO 6/6 0-4
Quint + ST 103
Note: Where no shank diameter is indicated, the shank *Catalogue 203/204: This data applies to a free shank length of 10 mm and the stated max. mounted
diameter specification is 6 mm. point dimensions.
80 I 209
Flexible Shaft Drives and Accessories
Flexible Shaft 4 ZG and 6 ZG and Handpieces
Angle handpiece WZ 4 A 323267 43 x 111 1:1 10* 0,270 ■■Max. speed: 20.000 RPM.
■■Incl. collet 3 mm.
■■Max. speed: 15.000 RPM when used with
a 6 mm collet.
Type with BSVH 24 ■■Belt grinding attachment: see page 96.
** Please enquire about cores and hoses * See page 94 for full collet range.
with sliding-type coupling at both ends.
209
209 I 81
Flexible Shaft Drives and Accessories
Flexible Shafts
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 206 Catalogue 208
outputs
RPM
TC burrs Mounted points Poliflex® Fan grinders Cut-off wheels EHT Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm fine grinding points head ø up to 40 mm ø up to 55 mm knotted type
ALU PLUS width up to 32 mm bond: matching RBG ø 70 mm
head ø 3 to 5 mm GR and PUR ATADISC® arbor
head ø up to 12 mm abrasive disc holder BO 6/10 0-4 or
RUER 8/180 SI / RUER 10/250 SI
cut 1, ALU, FVK GHR, LR and TX SHT 3575 with BO 8/10 0-4
head ø 5 to 10 mm head ø up to 20 mm abrasive disc AD 7505 see catalogue 206
Mammoth + ST 103
Wheel Brushes
HSS rotary cutters or ST 75 individual filament type
cut ALU, 1, 2, 3, 5 COMBIDISC® holders RBU ø 20 to 40 mm
head ø 3,2 mm SBH 20 up to 50
COMBIDISC®
abrasive discs
ø 20 to 50 mm
ø up to 80 mm Poliflex®
HSS rotary cutters marbling tools
RUER 8/180 SI
3.500 RPM
Note: Where no shank diameter is indicated, the shank *Catalogue 203/204: This data applies to a free shank length of 10 mm and the stated max. mounted
diameter specification is 6 mm. point dimensions.
82 I 209
Flexible Shaft Drives and Accessories
Flexible Shaft 6 Z and Handpieces
Angle handpiece WZ 6 657775 50 x 170 1,25 : 1 13* 0,225 ■■Max. speed: 18.000 RPM.
■■Incl. collet 6 mm.
Telescopic angled hand- 657782 35 x 170 1,38 : 1 14* 0,170 ■■Max. speed: 18.000 RPM.
piece WZT 6 3.0 ■■Incl. collet 3 mm.
Telescopic 657799 45 x 200 1,53 : 1 13* 0,210 ■■Max. speed: 18.000 RPM.
angled handpiece WZT 6 ■■Incl. collet 6 mm.
45° 6.0
209
209 I 83
Flexible Shaft Drives and Accessories
Flexible Shafts
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 205 Catalogue 206 Catalogue 208
outputs
RPM
cut 1, ALU, FVK Mounted points head ø up to 12 mm head ø up to 15 mm see catalogue 206
head ø 8 to 12 mm head ø up to 25 mm GHR, LR and TX POLICAP®
24.000 RPM
84 I 209
Flexible Shaft Drives and Accessories
Flexible Shaft 7 ZG/ZGU and Handpieces
Hose
182307 18 x 1.553 30 22 0,850 ■■Replacement casing, ready for installation.
7 ZG DIN 10/G 22**
182314 18 x 2.053 30 22 1,100
7 ZGU DIN 10/G 22 2 m
G22
Angle handpiece WZ 7 45° 303900 57 x 175 1,3 : 1 6* 0,665 ■■Max. speed: 17.100 RPM.
■■Incl. collet 6 mm.
G22
Angle handpiece WZ 7 B 323250 55 x 157 1,3 : 1 6* 0,600 ■■Max. speed: 17.100 RPM.
■■Incl. collet 6 mm.
**For cores and hoses with sliding-type * See page 94 for full collet range.
coupling at both ends, please enquire.
209 I 85
Flexible Shaft Drives and Accessories
Flexible Shafts
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 206 Catalogue 208
outputs
RPM
TC burrs Mounted points Poliflex® POLICAP® Cut-off wheels EHT Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 32 mm fine grinding points head ø up to 13 mm ø up to 55 mm knotted type
ALU PLUS width up to 32 mm bond: RBG ø 70 mm
head ø 7 to 10 mm GR and PUR Fan grinders matching
head ø up to 12 mm head ø up to 40 mm arbor
cut 1, ALU, FVK GHR, LR and TX BO 6/10 0-4 or
Mammoth + ST 103
TC burrs Mounted points Poliflex® Fan grinders Cut-off wheels EHT Wheel brushes
cut 3, 3 PLUS, 4, 5, head ø up to 50 mm fine grinding points head ø to 60 mm ø up to 55 mm knotted type
ALU PLUS width up to 13 mm bond: RBG ø 115 Bo. ø 22,2
head ø 10 to 16 mm GR, PUR and TX POLINOX® matching
ring wheels PNER arbor Pencil brushes
Mammoth / Record Grinder
head ø to 25 mm
Quint / Master Grinder
cut 1, ALU, FVK GHR, LR and LHR ø 50 mm BO 6/10 0-4 or individual filament type
head ø 16 mm head ø to 40 mm BO 8/10 0-4 PBU ø 10 to 20 mm
COMBIDISC®
RUG 19/120 SI
Note: Where no shank diameter is indicated, the shank *Catalogue 203/204: This data applies to a free shank length of 10 mm and the stated max. mounted
diameter specification is 6 mm. point dimensions.
86 I 209
Flexible Shaft Drives and Accessories
Flexible Shaft 10 ZG and Handpieces
Hose
10 ZG DIN 10/G 28** 182321 22 x 1.553 30 28 1,400 ■■Replacement casing, ready for installation.
10 ZG DIN 10/G 28 2 m** 182338 22 x 2.053 30 28 1,550
10 ZG DIN 15/G 28 182444 22 x 1.570 40 28 1,400
Flexible shaft 10 ZG Dim. acc. ■■Arbors and types see page 49.
DIN 10 or customer‘s 30 28 ■■Please enquire about possible bending
10 ZG DIN 15 require- 40 28 radii.
with rigid extension ments
G28 BSG 3/10/40 183014 131 x 132 505 x 40 2,220 ■■Max. speed: 5.000 RPM.
■■For short belts see catalogue 204.
** Please enquire about cores and hoses * See page 94 for full collet range.
with sliding-type coupling at both ends.
209 I 87
Flexible Shaft Drives and Accessories
Flexible Shafts
Catalogue 202 Catalogue 203* Catalogue 204* Catalogue 206 Catalogue 208
outputs
RPM
TC burrs Mounted points Poliflex® Fan grinders Cut-off wheels EHT Wheel brushes
Mammoth / Master Grinder
ME 22/150
ME 22/150
3.000 RPM
ME 22/150
1.600 RPM
bond: ø up to 200 mm ø up to 50 mm
GR and PUR POLICLEAN® wheels matching arbor BO 6/8
ø up to 125 mm ø 150 mm
Felt wheels POLIVLIES® wheels Cloth rings TR 12510
head ø to 125 mm ø 150 mm
Note: Where no shank diameter is indicated, the shank *Catalogue 203/204: This data applies to a free shank length of 10 mm and the stated max. mounted
diameter specification is 6 mm. point dimensions.
88 I 209
Flexible Shaft Drives and Accessories
Flexible Shaft 12 ZGA and Handpieces
Core
12 ZGA DIN 10/G 28** 182130 12 x 2.102 M10 7,5/5,85 1,300 ■■Replacement core, ready for installation.
12 ZGA DIN 15/G 28 182420 12 x 2.112 M14 7,5/5,85 1,300
Hose
12 ZGA DIN 10/G 28** 182352 25 x 2.045 30 28 2,450 ■■Replacement casing, ready for installation.
12 ZGA DIN 15/G 28 182468 25 x 2.059 40 28 2,500
G28
■■Max. speed: 12.000 RPM.
■■Incl. collet 6 mm.
■■Handpiece can be bent to a radius of
Flexible special 200 mm (per customer specification).
handpiece 182062 24 x 525 – 11* 1,000 ■■Special lengths available on request.
G28 BSG 3/10/40 183014 131 x 132 505 x 40 2,220 ■■Max. speed: 5.000 RPM.
■■For short belts see catalogue 204.
** Please enquire about cores and hoses * See page 94 for full collet range.
with sliding-type coupling at both ends.
209 I 89
Flexible Shaft Drives and Accessories
Flexible Shafts
HSS rotary cutters Flap wheels Cut-off and Wheel brushes Cup brushes
cut ALU, 1, 2, 3, 5 FR 10050 grinding wheels knotted type individual filament type
head ø 5 to 14 mm RBG ø 115 to 178 mm TBU ø 50 to 100 mm
matching POLIFAN® flap discs Bo. ø 22,2
Mammoth / Master Grinder
M 14
6.500 RPM
Note: Where no shank diameter is indicated, the shank *Catalogue 204: Specifications apply to a free shank length of 10 mm and
diameter specification is 6 mm. the stated max. mounted point dimensions.
90 I 209
Flexible Shaft Drives and Accessories
Flexible Shaft 12 KG, 15 KG and Handpieces
DIN 10/15 G 35 Dimen- Motor Handpiece ■■Speed range: n = 850 - 10.000 RPM
sions dia. coupling coupling ■■Output range: 525 - 6.280 watts.
x length dia. [mm] dia. [mm] ■■The speed and output ranges should not
[mm] be undercut or exceeded.
■■The radius of curvature should not be
Flexible shaft smaller than 240 mm.
(incl. handpiece 12/15 KG) 25 x 2.205 30 35 5,150 ■■Special lengths available on request.
12 KG DIN 10 181812 25 x 2.205 40 35 5,200 ■■Maintenance set for flexible shafts: see
12 KG DIN 15 181904 page 97.
Core
12 ZG/KG DIN 10/G 35 182123 12 x 2.102 M10 11/8,85 1,300 ■■Replacement core, ready for installation.
12 ZG/KG DIN 15/G 35 182413 12 x 2.108 M14 11/8,85 1,350
Hose
12 ZG/KG DIN 10/G 35 182345 25 x 2.060 30 35 2,450 ■■Replacement casing, ready for installation.
12 ZG/KG DIN 15/G 35 182451 25 x 2.060 40 35 2,500
Core
15 ZG DIN 15 / G 35 182147 15 x 2.108 M14 11/8,85 2,000 ■■Replacement core, ready for installation.
Hose
15 ZG DIN 15 / G 35 182369 30 x 2.060 40 35 3,750 ■■Replacement casing, ready for installation.
209 I 91
Tool Drive Accessories
Belt Sanding Attachment, Belt Sanders
Belt sanders
180 35 180 50 67
Types “E“ with rubber spindle bearing. Can be Ordering note: sive and non-woven belts.
connected to flexible shafts without hand- Please refer to catalogue 204 for detailed
piece. information and ordering data regarding abra-
92 I 209
Tool Drive Accessories
Angle Drives, Overdrive Unit
Matching accessories
Belt grinding attachement arbor
178
AF 14-1/4 for COMBIDISC®
AF 14/35 for ATADISC®
backing pad
GT 115 MF M14, H-GT 115 MF M14,
CC-GT 115-125 M 14 (see catalogue 204).
Order No. EAN Input speed Transmis- Output speed Drive Tool Suitable for
4007220 n max. sion at n max. spindle mounting flexible shaft
RPM ratio RPM thread [mm]
WT 7 E M14 G22 301708 25.000 2,7 : 1 9.300 M14 22,23 7 ZG, 7 ZGU 0,660
Order No. EAN Input speed Transmis- Output speed Drive Tool Suitable for
4007220 n max. sion at n max. spindle mounting flexible shaft
RPM ratio RPM thread [mm]
WT 10 H G28 349250 8.500 1,2 : 1 7.100 M14 22,23 10 ZG, 12 ZGA 1,000
209 I 93
Tool Drive Accessories
Collets
1 914913.. 01 02 03
ø7
ø5
15
16°
2 947016.. 03 01 03
M5
ø8
12
4° 1/4"-28UNF
3 900002.. 73 85 82
ø 7,5
16,6
8°
4 957717.. 03 01
ø 11
18
25°
5 900003.. 39 40 39
ø 7,62
ø 9,5
25,5
15°
M10 x 0,75
6 950325.. 03 06 01 17 16 04 02
ø 12,5
28-30
25°
7 900001.. 45 23 43 45 44 00
ø 11,34
ø 13,6
15°
8 952034.. 02 05 07 09
M14 x 1
ø 16,5
40
11°
9 914900.. 09 11 16 18 09 19
ø 12,1
ø8
27
15°
M8 x 0,75
10 957663.. 01 04 03 02
ø 10
24
11°
11 914909.. 09 12 17 19 23 09 27 26
ø 14,4
ø 10
32,2
17°
12 914902.. 03 04 06 08 09 10 11
ø 20,6
ø16
40
20°
M8 x 0,75
13 901018.. 23 30 50 60 23
ø 10
25
20°
14 901104.. 23 30 23
M5 x 0,5
ø8
23
* Please extend the order no. by the two- Order example no. 950325 03 = Collet 3 Acc. to the table (above), the order no. for
digit number from the table acc. to dia. mm for air-powered grinder PG 5/180 HV: collet group 6 = 950325 ..
[mm/inches]. Collets with special bores are Acc. to the table (below), the collet group 6 For ø 3 mm, please add 03.
available on request. has been defined for this machine. The complete order no. is 950325 03.
94 I 209
Tool Drive Accessories
Arbors, Extensions
78 144
SPV 50-3 S8 30 SPV 100-6 S8 30
9,5 8 12 8
104 150
20 SPV 150-3 S6 30
SPV 75-6 SPG 6
12 M10 x 0,75 11,5 6
120 150
SPV 75-6 S8 30 SPV 150-6 S8 30
12 8 13,5 8
129
SPV 100-6 SPG 6 20
12 M10 x 0,75
With spindle extensions shafts of grinding and When working with long shank lengths, it is vi- with standard shafts. The extension and a tool
milling tools can be extended. They allow ac- tal that the tool is inserted into the workpiece permitted for use at the appropriate RPM are
cess to difficult to reach areas. The extensions (e.g. cores, pipes, ducts or keyways) before the clamped into an impact-free chuck. Not
are rounded into collet (or instead of collets) tool drive is switched on. The extension must clamping on the shoulder radius.
of machines (air or electric powered) or in a not run free with the tool outside the work-
flexible shaft handpiece. piece (e.g. cores, pipes, ducts or keyways). Clamping of a second extension or of
Spindle extensions are an cost effective alter- tools with excessive length shanks is not
native to special types of made to order burrs If this rule is not observed, there is an permitted.
and mounted points with long shanks. increased risk of accidents. If the given condi-
tions are unfavourable, the extension with the
Safety note: tool clamped in it may buckle. The exten-
Caution! When using spindle extensions, sions are only intended for manual use
please observe the valid safety regula- in connection with suitable air-power, electric
tions and the accident prevention regula- grinders or flexible shaft handpieces for tools
tions.
Order No. EAN Max. speed Dia. mounting Tool Overall Length Outer Incl. Collet
4007220 [RPM] pin mounting length mounting pin tool collet group
(motor/hand- [mm] [mm] [mm] holder dia. [mm]
piece) dia.
[mm] [mm]
SPV 50-3 S8 185254 44.000 8 3 78 30 9,5 3 2* 0,035
SPV 75-6 SPG 6 333143 20.000 SPG 6 6 104 Special 12,0 6 10* 0,073
SPV 75-6 S8 185278 20.000 8 6 120 30 12,0 6 10* 0,076
SPV 100-6 SPG 6 656051 20.000 SPG 6 6 129 Special 12,0 6 10* 0,096
SPV 100-6 S8 185261 20.000 8 6 144 30 12,0 6 10* 0,098
SPV 150-3 S6 185308 10.000 6 3 150 30 11,5 - - 0,055
SPV 150-6 S8 185315 10.000 8 6 150 30 13,5 - - 0,082
* All available collets are shown on the adjacent page.
209
209 I 95
Tool Drive Accessories
Belt Grinders for Flexible Shafts and Handpieces
Medium-sized belt grinding attachments ■■The belt grinder attachment can be pivoted ■■Highly-accurate belt guidance due to adjust-
BSVH 36 and BSVH 41 for belt lengths 520 on the respective tool drive or the handpiece able belt clamping force and fixable belt
and 610 mm. Small belt grinding attach- and therefore allows flexible adaptation to arms.
ments BSVH 25,5 and BSVH 24 for belt length each work situation. ■■Easy, quick belt replacement due to spring
305 mm. clamping.
ø 25
8.8 8.8
3.8
3.8 BSVA 4/16
ø 16
BSVAK 4/16
ø 16
8.8
BSVA 9/16
ø 16
8.8
BSVA 12/19
ø 19
8.8
BSVAK 9/16 18
ø16
BSVA 18/23
ø 23
96 I 209
Tool Drive Accessories
Maintenance Products
After approx. 100 operating hours, the core 2 non-linting cleaning cloths
of a flexible shaft has to be re-lubricated. The (400 x 330 mm) Maintenance sets
core and hose must be de-greased and new The core is freed of the old grease using a
special shaft grease must be applied to the de-greasing agent and a cleaning cloth (do not
core. use cotton waste)! Apply new grease on to
the second cloth and pull the core through it.
Maintenance set consists of:
1 can of shaft grease FT 4
1 Hose brush (approx. 0,500 kg)
For removing the old grease from the flexible Special grease with special lubrication and
casing. adhesive properties.
209 I 97
Personal Protection Equipment (PPE)
Safety Glasses
98 I 209
Personal Protection Equipment (PPE)
Protective Gloves, Ear Protection, Breathing Protection
209 I 99
Quality Tools from One Source
Mounted Points
Files Burrs Mounted Points
203
203 I 1
Fine Grinding and Polishing Tools Diamond and CBN Tools Grinding and Cut-Off Wheels
Platzhalter Platzhalter
für Titel für Titel
207
208
209
100 I 209