Professional Documents
Culture Documents
Webtrol has been building Booster Pumps for Features And Benefits
over 40 years for various industrial, commercial • Available in both Stainless Steel and Cast
and agricultural uses and has long been a Iron fitted models.
leader in the Reverse Osmosis and Deionization • Heavy duty stainless steel hex shaft with
Industry. stainless steel coupling.
• High strength, glass filled Delrin, polycarbonate
Webtrol’s commitment to quality is defined in or Noryl impellers, precision machined for
the construction of each Booster Pump, through dimensional stability and efficiency.
use of only quality materials and precision • Injection molded polycarbonate or Noryl
machining by journeyman machinists. Every diffusers with molded in stainless steel wear
pump is hand assembled and checked during rings at all critical wear points.
each step, up to the final test, where each pump • Heavy wall stainless steel pump housing
is checked for flow, pressure, power consump-
tion, leaks, vibration and noise. Specifications
Webtrol EZ Series Booster Pumps are available
from 5 to 35 Gallons Per Minute. Pressures to
500 PSI
1 2 3 4 5 6 7
13 12 8 11 10 9 8
Cast Iron EZ Series
1 2 3 4 5 6 7
13 12 8 11 10 9
Stainless Steel EZ Series
1 Motor
The motor is a “C” face, 3450 RPM, 50 or 60 cycle, single or three phase, open drip proof (TEFC available) with long life thrust
bearings, sized to support the thrust loads generated by the pump. Motors through 3 HP are Nema Standard 56J frame with a
threaded shaft and greased for life ball bearings. 5 HP motors are foot mounted 184CYZ frame with a keyed shaft and greasable
high thrust angular contact bearings.
4 Impellers
High strength glass filled Delrin or polycarbonate thermoplastic impellers provide pulse free pressure boost. All impellers are
injection molded and machined to insure dimensional accuracy and balance. Noryl impellers are available upon request.
5 Diffusers
High strength polycarbonate diffusers are injection molded, concentrically aligned, providing perfectly aligned, clean, smooth
water passages for higher efficiencies. Noryl diffusers are available upon request.
6 Shaft
Stainless steel hex shaft is cold drawn to exacting tolerances, to eliminate shaft run out for vibration free operation.
7 Discharge
The discharge is cast iron or investment cast stainless steel depending on the type of construction you choose. All discharge
connections ar female NPT.
8 O-Rings
Positive sealing “Buna N” o-rings are used to seal off both ends of the pump housing on cast iron models. A Viton o-ring is used
to seal the inlet side of the pump housing on stainless steel models.
10 Pump Housing
Thick wall stainless steel tubing is used on all models. Cast iron models are threaded on both ends. Stainless steel models are
threaded on the inlet side with a discharge that has been machine welded to the tube on the other end.
11 Rotating Assembly
The entire rotating assembly, consisting of impellers, diffusers, top and bottom plates, bearings, shaft and coupling, is easily field
replaceable.
12 Coupling
Stainless steel coupling has interference fit onto the pump shaft and pinned to lock in place. Depending on the motor frame size,
the coupling either screws onto the motor shaft or slips onto the motor shaft and is keyed in place. Set screws lock the coupling
to the motor shaft.
13 Mechanical Seal
The spring loaded, positive sealing, mechanical seal has a ceramic stationary face and a carbon rotating face. Metal compo-
nents on the rotating half are stainless steel and the elastomers are Buna N (Nitrile) on cast iron models and Viton on stainless
steel models. The standard seal will handle inlet pressures up to 100 PSI, while an optional seal is available for pressures up to
250 PSI.
300 G Series
Discharge Pressure (PSI)
250
200
150
100
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
600
500 H Series
Discharge Pressure (PSI)
400
300
200
100
H5 H10 H15 H20 H35
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
G5B28 1.5HP
G5
300
G5B23 1HP
250
Discharge Pressure (PSI)
150
G5B12 .75HP
G5B10 .5HP
50
0
0 2 4 6 8 10
Flow (gallons per minute)
G10B26 2HP
G10
300
250
G10B18 1.5HP
Discharge Pressure (PSI)
200
G10B15 1HP
G10B14 1HP
G10B8 .75HP
100
G10B6 .5HP
G10B5 .5HP
G10B4 .5HP
50
0
0 4 6 8 10 12 14 16
Flow (gallons per minute)
250
200
Discharge Pressure (PSI)
G15B14 1.5HP
150
G15B9 .75HP
G15B5 .5HP
50
0
0 4 6 8 10 12 14 16 18
Flow (gallons per minute)
250
200
Discharge Pressure (PSI)
G20B15 2HP
150
G20B12 1.5HP
G20B9 1HP
100
G20B7 .75HP
G20B4 .5HP
50
G20B3 .5HP
0
0 5 10 15 20 25 30
Flow (gallons per minute)
G35B16 3HP
180 G35
160
G35B12 2HP
140
Discharge Pressure (PSI)
120
G35B9 1.5HP
100
80 G35B6 1HP
G35B5 .75HP
60
G35B3 .5HP
40
G35B2 .5HP
20
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
53
50
40 38
0.52
30 0.51
0.50
0.49
BHP
0.48
20
20 0.47
0.46
0.45
0.44
10 0.43
2 4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
90
83
86
80 76
G5B7
70
Discharge Pressure (PSI)
62
60
50
44
40
0.60
0.58
30 0.56
BHP
0.54
0.52 20
20 0.50
0.48
0.46
10 2 4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
70 67
60
50 46
0.72
40
0.70
0.68
30
BHP
0.66
0.64 21
20
0.62
0.60
10 2 4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
140
122
120 116
G5B10
104
Discharge Pressure (PSI)
100
86
80
61
60 0.80
0.78
0.76
40
BHP
0.74
0.72 30
0.70
20 0.68
2 4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
120
120 G5B12
Discharge Pressure (PSI)
99
100
80
71
60 0.92
0.90
0.88
0.86
40
40
BHP
0.84
0.82
0.80
0.78
0.76
20 0.74
2 4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
200
194 184
180
167
G5B17
160
Discharge Pressure (PSI)
140 136
120
100 94
1.28
80
1.24
60 1.20
BHP
1.16 46
40 1.12
1.08
20 4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
254
250 241 G5B23
Discharge Pressure (PSI)
211
200
163
150
1.52
101
100 1.48
BHP
1.44
1.40
50 46
1.36
4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
350
327
308
300 G5B28
265
Discharge Pressure (PSI)
250
204
200
150 1.95
1.90
120
1.85
100
BHP
1.80
1.75
1.70
50 1.65
46
4 6 8 10
GPM
0
0 2 4 6 8 10 12
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
50
50 48 G10B4
46
43
Discharge Pressure (PSI)
40 39
32
30
0.59 25
0.57
20 0.55
0.53
BHP
0.51
15
0.49
10 0.47
0.45
4 6 8 10 12 14
GPM
0
0 2 4 6 8 10 12 14 16
Flow (gallons per minute)
70
68 64
67
61
60 G10B5
56
Discharge Pressure (PSI)
50 48
40 39
30 0.62 28
0.60
0.58
20
BHP
0.56
0.54
0.52
10 0.50
4 6 8 10 12 14
GPM
0
0 2 4 6 8 10 12 14 16
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
55
50
45
40
0.80
33
30
0.75
BHP
0.70
20
0.65
10 0.60
4 6 8 10 12 14
GPM
0
0 2 4 6 8 10 12 14 16
Flow (gallons per minute)
110
104
101
100 97
92
90 86
G10B8
Discharge Pressure (PSI)
80 76
70
64
60
50 48
0.96
40 0.94
0.92
BHP
30 0.90 29
0.88
20 0.86
0.84
10 6 8 10 12 14 16
GPM
0
0 2 4 6 8 10 12 14 16 18
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
141 138
140 133
125
G10B12
120
Discharge Pressure (PSI)
113
100
100
84
80
1.20 63
60
1.15
BHP
1.10
40 38
1.05
20 1.00
6 8 10 12 14 16
GPM
0
0 2 4 6 8 10 12 14 16 18
Flow (gallons per minute)
180
165 161
160 155
146 G10B14
140 132
Discharge Pressure (PSI)
120 115
100 94
80 1.40
69
1.35
60
BHP
1.30
43
40 1.25
1.20
20 6 8 10 12 14 16
GPM
0
0 2 4 6 8 10 12 14 16 18
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
140 134
120
112
100
1.65 78
80
1.55
60
BHP
1.45
47
40 1.35
1.25
20 6 8 10 12 14 16
GPM
0
0 2 4 6 8 10 12 14 16 18
Flow (gallons per minute)
240
226 223
215
202
200 G10B18
185
Discharge Pressure (PSI)
160
160
131
120
2.00 95
1.95
80 1.90
BHP
1.85
56
1.80
40 1.75
1.70
6 8 10 12 14 16
GPM
0
0 2 4 6 8 10 12 14 16 18
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
252
240
221
200 183
160 142
2.70
2.68
120 2.66
2.64
95
BHP
2.62
2.60
80 2.58
2.56
2.54
40 8 10 12 14 16
GPM
0
0 2 4 6 8 10 12 14 16 18
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
70 69 67
65
63
G15B5
60 59
Discharge Pressure (PSI)
53
50
44
40
36
0.79
30 0.77
0.75 26
BHP
0.73
20 0.71
0.69
0.67
10 0.65
6 8 10 12 14 16 18
GPM
0
0 4 6 8 10 12 14 16 18 20
Flow (gallons per minute)
100 95
90
90 86
81 G15B7
80 75
Discharge Pressure (PSI)
70 67
60 55
50
43
1.10
40
1.05
30
30 1.00
BHP
0.95
20 0.90
0.85
10 6 8 10 12 14 16 18
GPM
0
0 4 6 8 10 12 14 16 18 20
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
80
80
69
60 56
1.30
1.25
40
40 1.20
BHP
1.15
1.10
20 1.05
1.00
6 8 10 12 14 16 18
GPM
0
0 4 6 8 10 12 14 16 18 20
Flow (gallons per minute)
180
168
174 163
160 154
142 G15B14
140
Discharge Pressure (PSI)
128
120
109
100
89
80
2.05
1.95 65
60 1.85
BHP
1.75
40 1.65
1.55
1.45
20 6 8 10 12 14 16 18
GPM
0
0 4 6 8 10 12 14 16 18 20
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
200 189
163
160
135
120 2.35
2.25 103
2.15
2.05
80
BHP
1.95
1.85
1.75
1.65
1.55
40 1.45
6 8 10 12 14 16 18
GPM
0
0 4 6 8 10 12 14 16 18 20
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
40
40 39
37
35 G20B3
35
33
Discharge Pressure (PSI)
30 28
25
22
20
0.58
0.57 16
15 0.56
BHP
0.55
10 0.54
0.53
0.52
5 10 14 18 22 26
GPM
0
0 2 6 10 14 18 22 26 30
Flow (gallons per minute)
55
52
53 50
50
47
45 43
G20B4
Discharge Pressure (PSI)
40 38
35
30
30
25
0.74
21
0.72
20 0.70
0.68
BHP
15 0.66
0.64
0.62
10 0.60
0.58
5 10 14 18 22 26
GPM
0
0 2 6 10 14 18 22 26 30
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
61
60
51
50
40
1.15 35
1.10
30 1.05
BHP
1.00
20 0.95
0.90
0.85
10 10 14 18 22 26
GPM
0
0 2 6 10 14 18 22 26 30
Flow (gallons per minute)
110
104
108 100
100
95
90 86
G20B9
Discharge Pressure (PSI)
80 77
70
63
60
50
1.35 44
1.30
40 1.25
1.20
BHP
30 1.15
1.10 24
1.05
20 1.00
0.95
10 10 14 18 22 26 30
GPM
0
0 2 6 10 14 18 22 26 30 34
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
112
100 99
80 77
1.90
60 1.85
1.80 52
1.75
BHP
1.70
40 1.65
1.60
1.55 24
20 1.50
10 14 18 22 26 30
GPM
0
0 2 6 10 14 18 22 26 30 34
Flow (gallons per minute)
180
169
174 160
160
151
G20B15
138
140
Discharge Pressure (PSI)
124
120
100
100
80
2.30 69
2.20
60 2.10
BHP
2.00
40 1.90 35
1.80
1.70
20 10 14 18 22 26 30
GPM
0
0 2 6 10 14 18 22 26 30 34
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
200
184
159
160
123
120 3.40
3.30
3.20
3.10
80 77
BHP
3.00
2.90
2.80
2.70
2.60
40 2.50
10 14 18 22 26 30
GPM
0
0 2 6 10 14 18 22 26 30 34
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
30 30 G35B2
28
26
Discharge Pressure (PSI)
25 24
21
20
18
15 0.52 14
0.51
0.50
0.49
10
BHP
0.48 9
0.47
0.46
0.45
0.44
5 0.43
15 20 25 30 35
GPM
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
45
42
40
40
37 G35B3
35 34
Discharge Pressure (PSI)
30
30
26
25
20
20
0.76
0.74
0.72 14
15 0.70
BHP
0.68
0.66
10 0.64
0.62
0.60
5 15 20 25 30 35
GPM
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
49
50
43
40
34
30 1.05
1.00 23
0.95
20
BHP
0.90
0.85
10 0.80
15 20 25 30 35
GPM
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
80
74
78
70
70
65 G35B6
60 58
Discharge Pressure (PSI)
51
50
41
40
1.25
30 1.20 28
1.15
BHP
1.10
20
1.05
1.00
10 0.95
15 20 25 30 35
GPM
0
0 5 10 15 20 25 30 35 40
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
80 79
66
60
50
1.85
1.75
40
1.65
BHP
33
1.55
1.45
20
1.35
15 20 25 30 35 40
GPM
0
0 5 10 15 20 25 30 35 40 45
Flow (gallons per minute)
160
142
140 137
131
126 G35B12
118
120
Discharge Pressure (PSI)
108
100
91
80
69
2.50
60 2.40
2.30
43
BHP
2.20
40 2.10
2.00
1.90
20 1.80
25
15 20 30 35 40
GPM
0
0 5 10 15 20 25 30 35 40 45
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
140 136
120 118
100 93
3.30
80
3.20
3.10 61
60
BHP
3.00
2.90
40 2.80
2.70
2.60
20 15 20 25 30 35 40
GPM
0
0 5 10 15 20 25 30 35 40 45
Flow (gallons per minute)
Note:
Curves are based on 60 Hz 3450 rpm motors. 50 Hz 2875 rpm curves are available. These curves are for general guidance only, individual
pump curves are available upon request. A certified curve may be requested for an additional cost. Webtrol will build pumps to fit your
specific needs, contact factory for pricing.
A B
1.90
Suction .50
5.50
Discharge
NPT
7.10
.97 (1) .406 Dia. Hole Motor Support .81 (2) .406 Dia.
On Pump CL 71B125-6 5.25
Bolt Holes
1.40 6.25
1/3 Thru 3 HP Models
A B J
1.90
.50 K
Suction NPT
Discharge H
NPT L
Pump Support
.97 (1) .406 Dia. Hole On Pump C
L D 6 Holes .41 DIA
1.40 E
C D1 F
5 HP Models
1. The inlet and discharge thread size for C.I. and stainless steel models in the 5, 10, 15 GPM pump sizes is 1” NPT; The 20
and 35 GPM pump size is 1 1/2” NPT.
2. Pump models that are 14 stages or more are equipped with a pump support located near the discharge of the pump.
For stability, this support should be mounted approximately 4” from the discharge.
3. Allow 8” min. clearance behind the motor for maintenance.
Inlet/Motor
Motor Bracket
Rotating Assembly Discharge
Inlet/Motor
Motor Bracket
Rotating Assembly
Webtrol manufactures many different models of EZ Series Booster Pumps. To be sure you get the right part you
need, we ask that you call (314) 631-9200 and let one of our trained customer service representatives assist you.
There are 7 basic components that make up an EZ Series Booster Pump. These seven components are shown
above in the display model pumps.
To order parts, note the model number and the date code of the EZ Booster pump you need a repair part for.