Professional Documents
Culture Documents
Boimetric User Manual v1.0
Boimetric User Manual v1.0
GUIDELINE
USER MANUAL
Version (1.0)
Page 1 of 18
Table of Contents Page No.
2. Installation Instructions
3. Operating Instructions
3.1) Register Beneficiary ------------------------------------------------------ 11
3.2) Update Registered Beneficiary------------------------------------------ 15
3.3) Attendance ----------------------------------------------------------------- 17
Page 2 of 18
1) Hardware & Software Requirement
1.1) Hardware Requirements
For the proper functioning of the biometric device, bellow hardware requirements must
be fulfilled at the client side:
Biometric Device: Use the latest biometric device. In our case we are using
NITGEN biometric device (Model: HFDU08).
Click on the link (others -> Download Driver for Biometric Device)
Page 3 of 18
Setup of Biometric Device: Setup of Biometric device also can be downloaded from
the NULM website (http://nulm.gov.in)
Click on the link (others -> Download Setup for Biometric Device)
Page 4 of 18
2) Installation Instructions
Step 2. Please unplug the biometric device from USB port if already connected.
Page 5 of 18
Step 4. Click on button to install drivers
Step 5. When setup will ask to plug in device to USB then only plug in.
Please wait for a movement for the message (Please connect the device) is to appear
on thescreen. Once the message is appeared (Please connect the device), please
connect the biometric device in the USB port. You should not click on the button
. After connecting biometric device in USB port you will get the
finish button. Press the finish button to complete the installation.
Do not plug in biometric device to USB until this message is not appeared.
Page 6 of 18
Step 6. Plug in biometric device like this:-
Page 7 of 18
Steps to check whether the biometric driver is installed or not.
Step 7. To check whether driver is installed successfully or not follow the bellow
instruction:-
Go to Start >> run and type NFD and then press enter. This will open device diagnostic
utility. Under Device tab click on device scan button, click init button then place finger
on sensor and click capture. Just check if image appear on left window or not. If
appeared that means drivers installed successfully.
Page 8 of 18
2.2) Steps for installing biometric device setup
Step 1. Your downloaded file Name would be
(Biometric_Device_Setup_v4.861_x86.zip).
Unzip file by right click on the zip folder.
Step 2. Now, open the folder and click on Setup.exe file and follow the instruction.
Page 9 of 18
Step 3. Finally click on button
Page 10 of 18
3.) Operating Instructions
3.1) Register Beneficiary
Note:- Biometric device will work only on Internet explorer (version above 8.0)
Step 2. Login with your training centre user ID and click on the menu:-
Click on Allow.
Page 11 of 18
Step 4. Select training and click on button.
attendance.
Click on Register
button to register
beneficiary
Click on Next
Button
Page 12 of 18
Step 7. Click on the blue color associated with the fingers.
Step 8. Now place your finger (twice) on the sensor of biometric device.
Page 13 of 18
Step 9. After registration, click on button.
Page 14 of 18
3.2) Update Beneficiary
Step 1. To update / change the registered finger of beneficiary, click on the following
menu:-
Page 15 of 18
Step 4. It will ask you to enter the reason for changing the finger. Please fill the reason
and click on ok button.
Enter the actual reason for changing the finger and then click on ok button
Page 16 of 18
3.3) Attendance through biometric device
Step 1. To make attendance through biometric device click on the following menu:-
Step 2. Select training and presence for (Start / End) and click on Show button
Page 17 of 18
Step 4. Once you click on this button, the sensor of the device
Step 5. Now place your registered finger on the sensor of biometric device like this:-
Page 18 of 18