Professional Documents
Culture Documents
Avh-280bt: Avh-280bt Avh-285bt Avh-285bt Avh-285bt Avh-289bt
Avh-280bt: Avh-280bt Avh-285bt Avh-285bt Avh-285bt Avh-289bt
CRT5859
AVH-280BT/XNUC
AVH-280BT /XNUC
AVH-280BT/XNEU5
AVH-285BT/XNRC
AVH-285BT/XNRD
AVH-285BT/XNRI
AVH-289BT/XNID
This service manual should be used together with the following manual(s):
CX-3311 CRT5651 LS2.5 DVD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly,
Diagnosis , Each Setting and Adjustment
SAFETY INFORMATION
A CAUTION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or other reproductive
B harm.
Health & Safety Code Section 25249.6 - Proposition 65
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
D CAUTION
This product is a class 1 laser product classi-
fied under the Safety of laser products, IEC
60825-1:2007, and contains a class 1M laser
module. To ensure continued safety, do not re-
move any covers or attempt to gain access to
the inside of the product. Refer all servicing to
qualified personnel.
WARNING!
The AEL (accessible emission level )of the laser power output is less than CLASS 1
but the laser component is capable of emitting radiation exceeding the limit for
CLASS 1.
A specially instructed person should do servicing operation of the apparatus.
F
AVH-280BT/XNUC
2
1 2 3 4
5 6 7 8
A
Laser diode characteristics
Wave length:
DVD:660 nm to 670 nm
CD:780 nm to 800 nm
Focus lens on Maximum output:
CD:6.26 mW(Emitting period :9 sec.)
DVD:1.27 mW (Emitting period : unlimited)
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacturer. C
Discord used batteries according to the manufacturer's instructions.
AVH-280BT/XNUC
5 6 7 8
3
1 2 3 4
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON DISASSEMBLY / ASSEMBLY................................................................................................. 6
1.3 NOTES ON OPERATION CHECK / DIAGNOSIS ...................................................................................... 7
1.4 NOTES ON REPLACING PARTS .............................................................................................................. 7
1.5 NOTES ON ADJUSTMENT ....................................................................................................................... 7
1.6 OTHERS .................................................................................................................................................... 7
2. SPECIFICATIONS ............................................................................................................................................ 8
2.1 SPECIFICATIONS...................................................................................................................................... 8
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 8
3. BASIC ITEMS FOR SERVICE.......................................................................................................................... 9
3.1 CHECK POINTS AFTER SERVICING....................................................................................................... 9
3.2 PCB LOCATIONS .................................................................................................................................... 10
B 3.3 JIGS LIST ................................................................................................................................................ 11
3.4 CLEANING............................................................................................................................................... 11
4. BLOCK DIAGRAM.......................................................................................................................................... 12
4.1 OVERALL CONNECTION DIAGRAM...................................................................................................... 12
4.2 BLOCK DIAGRAM ................................................................................................................................... 13
4.3 POWER SUPPLY SYSTEM FIGURE....................................................................................................... 15
5. DIAGNOSIS.................................................................................................................................................... 18
5.1 OPERATIONAL FLOWCHART ................................................................................................................ 18
5.2 INSPECTION METHOD OF PICKUP UNIT............................................................................................. 19
5.3 ERROR CODE LIST ................................................................................................................................ 22
5.4 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 24
6. SERVICE MODE ............................................................................................................................................ 25
C 6.1 VERSION INFORMATION ....................................................................................................................... 25
6.2 SERVICE TEST MODE ........................................................................................................................... 25
6.3 FIRMWARE UPGRADE ........................................................................................................................... 38
7. DISASSEMBLY............................................................................................................................................... 41
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 45
8.1 ADJUSTMENT REQUIRED WHEN HTE UNIT IS REPLACED............................................................... 45
8.2 FLICKER ADJUSTMENT......................................................................................................................... 46
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 47
9.1 PACKING ................................................................................................................................................. 47
9.2 EXTERIOR(1) .......................................................................................................................................... 50
9.3 EXTERIOR(2) .......................................................................................................................................... 52
9.4 DVD MECHANISM MODULE(1) .............................................................................................................. 54
D 9.5 DVD MECHANISM MODULE(2) .............................................................................................................. 56
10. SCHEMATIC DIAGRAM ............................................................................................................................... 57
10.1 MOTHER UNIT (SENSE)....................................................................................................................... 57
10.2 MOTHER UNIT (BT IF) .......................................................................................................................... 58
10.3 MOTHER UNIT (USB_POW) ................................................................................................................. 59
10.4 MOTHER UNIT (I/F)............................................................................................................................... 60
10.5 MOTHER UNIT (E.VOL) ........................................................................................................................ 61
10.6 MOTHER UNIT (DDC 2ch) .................................................................................................................... 62
10.7 MOTHER UNIT (TUNER) ...................................................................................................................... 63
10.8 MOTHER UNIT (PWIC) ......................................................................................................................... 64
10.9 MOTHER UNIT (ucom) .......................................................................................................................... 65
10.10 MOTHER UNIT (POWER) ................................................................................................................... 66
E 10.11 MOTHER UNIT (SOC) ......................................................................................................................... 67
10.12 MONITOR PCB (PCB_IF).................................................................................................................... 68
10.13 MONITOR PCB (LCD_BL) ................................................................................................................... 69
10.14 MONITOR PCB (LCD_PW) ................................................................................................................. 70
10.15 MONITOR PCB(LCDI/F) ...................................................................................................................... 71
10.16 MONITOR PCB(TCON) ....................................................................................................................... 72
10.17 MONITOR PCB(ISO) ........................................................................................................................... 73
10.18 RELAY UNIT ........................................................................................................................................ 74
10.19 KEY PCB ............................................................................................................................................. 75
10.20 WAVEFORMS ...................................................................................................................................... 76
11. PCB CONNECTION DIAGRAM ................................................................................................................... 78
11.1 MOTHER UNIT ...................................................................................................................................... 78
F
11.2 MONITOR PCB...................................................................................................................................... 80
11.3 RELAY UNIT .......................................................................................................................................... 82
11.4 KEY PCB ............................................................................................................................................... 84
12. ELECTRICAL PARTS LIST .......................................................................................................................... 85
AVH-280BT/XNUC
4
1 2 3 4
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and
A
should keep the safety during servicing by following the safety instructions described in this manual.
Please keep the distance of more than 13 cm from focus lens for safety when you check pickup and make adjustment,
and do not look straight at Laser Beam for more than 10 seconds.
area and a heat sink becomes hot areas. Be careful not to burn yourself.
IC1301 B
L902
C1319
IC1201
IC111
IC741 IC601
IC861
1F & 2F
Rear Holder
AVH-280BT/XNUC
5 6 7 8
5
1 2 3 4
The shorting-solder protects the laser diode (LD) from the static electricity. When replacing the DVD Mechanism
Module, please take an appropriate treatment (shorting-solder) by referring to the procedure below.
B
Shorting-solder land
for CD
Shorting-solder land
for DVD
(2) After confirming the shorting-solder has been done securely, remove the DVD Mechanism Module of the product.
When replacing the Mechanism Module, please connect it to the product at first and then
F
remove the shorting-solder in reverse order of the previous procedure for removing.
AVH-280BT/XNUC
6
1 2 3 4
5 6 7 8
Please be careful of not to apply static charge onto integrated circuits, etc, when you conduct repair work. B
Especially, please use soldering iron with its tip grounded.
Also, please use a pair of tweezers with static charge protection capability if there is the possibility of contacting to
device terminals, and avoid the use of metal-made tweezers.
On this mechanism, Pickup and Spindle Motor can not be replaced at the Service Site, because a special facility is
required for the adjustment after replacing them.
So, if Pickup or Spindle Motor is defective, replace the DVD Mechanism Module.
The skew adjustment and LD power adjustment for the DVD Mechanism Module have already finished, so you cannot
replace its Pickup unit or board unit separately.
D
1.6 OTHERS
Notes on soldring
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
E
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for
repairs accompanied by reworking of soldering.
AVH-280BT/XNUC
5 6 7 8
7
1 2 3 4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
For all items except the backup current, refer to the Owner's Manual.
A
Backup current......................... 5.0 mA or less
AVH-280BT/XNUC
8
1 2 3 4
5 6 7 8
For check items concerning image and voice, please refer to the followings:
AVH-280BT/XNUC
5 6 7 8
9
1 2 3 4
A Mother Unit
C Relay Unit
D Key PCB
B Monitor PCB
A:AVH-280BT/XNUC
C
B:AVH-280BT/XNEU5
C:AVH-285BT/XNRC
D:AVH-285BT/XNRD
E:AVH-285BT/XNRI
F:AVH-289BT/XNID
AVH-280BT/XNUC
10
1 2 3 4
5 6 7 8
- Jigs List
Name Jig No. Remarks A
Disc(DVD-Video) GGV1025 Check points after servicing, Inspection method of Pickup Unit
(TDV-582)
Disc(CD-DA) TCD-782 Inspection method of Pickup Unit
30P FFC GGD1222 RELAY UNIT <–> MOTHER UNIT
- Grease List
Name Jig No. Remarks
Grease GEM1024 DVD Mechanism Module
Grease GEM1045 DVD Mechanism Module
Grease GEM1043 DVD Mechanism Modulet
B
3.4 CLEANING
Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools:
Portions to be cleaned Cleaning tools
DVD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
AVH-280BT/XNUC
5 6 7 8
11
F
A
12
REAR VIEW
1
1
CAMERA WIRED BT MIC
FM/AM USB IF POWER SUPPLY
AUX RREOUT REMOTE WIRED REMOTE
ANT VIDEO OUT
NM
18
1
JA2201 JA3191 JA3151 JA3101 JA3161 JA3121 JA3122 JA901
CN102
1 30
CN801 A MOTHER UNIT
2
C A 3/11 USB_POW A 9/11 ucom
RELAY UNIT
AVH-280BT/XNUC
30 1
A 6/11 DDC 2ch
1 24
CN3201
60
1
3
3
60
1
CN5003
1
1
2
1
4
4
4
CN5301
BACKLIGHT TFT LCD MODULE TOUCH PANEL
4.2 BLOCK DIAGRAM
- SYSTEM BLOCK DIAGRAM
TUN
ANT
TUN3.3
A MOTHER UNIT SYSB
Mute
RCAout
5
5
6
MN103LF15RXW B.Rem
MUTE
PBSENS P.B
AVH-280BT/XNUC
BGSENS B.G
AUXL,AUXR
ISENS ILM
ASENS ACC
AUX BSENS B.UP B.UP
B.Camera SYS5
7
USB5 CPRST VDD1.3 S CLK LCD1.8
CPPW S DAT IC5402
USB LCD 6.2inch
Component TW8832SAT-
SOC LB1-GRSH CWX4348
CXK8200
SUN+L , SUN+R
IC601 LCD POWER VM6
SYStoS+ , S+toSYS IC5101 V18
SPHE8202GQHL11P LCD3.3 R1290K103A V92
Flash-ROM B.UP LCD3.3
RFVCC5 LECRGM IC721 DD8 BACK LIGHT
LECRGP IC5101
DVCC3.3
SPDLM ILMB OZ527ILN
DD4.3
SPDLP
5Vreg SDRAM
B.UP
DD8 Motor Driver IC741
8
KEY REM
8
LED
IC861 VDD3.3
BA5839FP DD8
DVCC3.3
ILMB
B MONITOR PCB
D KEY PCB
13
A
F
B
F
A
14
1
LITHIO RCA
Tuner TUNL,TUNR Mute
IC2201 CH2 CH3
TEF6686HN
CH1 RCA
SAPPHIRE Mute
E-VOL
IC1201
BT Module PM9012A AMP
U2901 BT_L , BT_R Active
CH6 Mute Power IC
CWX4772 LPF
IC1301
+4.2 B
E.VOL MUTE soft mute)
2
2
PA2032A
CH5
AVH-280BT/XNUC
Active µ-com
AUXL,AUXR LPF IC401
MN103LF15RXW
ISO
IC1113
NJM2505AF V.Drive
IC1131
ISO NJM41050V
IC1112
BH7673G
3
3
C.Video ISO
IC1111
V.Drive B MONITOR PCB
NJM2505AF IC1132
NJM41010F1
T-Con RGB
888 LCD
IC5402
6.2 inch
TW8832SAT-
LB1-GRSH CWX4348
USB_DM , USB_DP Component (Y/Cb/Cr)
SOC
4
4.3 POWER SUPPLY SYSTEM FIGURE
Voltage Current Current
B.UP VF = 0.7V 3.3V VDD3.3 A MOTHER UNIT (Typ) (Typ) (Max)
min 10.8 V NJW4181U3-33B 3.3V System µ-COM
3.30V 24.0mA 48.0mA
typ 14.4 V + typ 24.0 mA MN103LF14RXW
max 15.1 V
KBUP
max 49.5 mA
typ 0.250 W
470uF max 0.549 W EEPROM
5
5
3.30V - 1.5mA
S-93C66BD0I
LDO
DDC 8.0V SYSB
SW NJW4184DL3-08A 8.0V E-VOL(SAPPHIRE)
8.40V 43.0mA 55.0mA
typ 63.0 mA PM9012A
max 95.0 mA
typ 0.403 W
max 0.675 W LPF(2x4 ch)
8.40V 20.0mA 40.0mA
rSYSPW
Video_SEL
5.00V 15.0mA 22.0mA
NJM41050
6
6
Video_SEL
5.00V 8.0mA 15.0mA
NJM41010
AVH-280BT/XNUC
AUX ISO(Composit)
5.00V 4.8mA 8.0mA
NJM2505AF
SoC ISO(Composit)
5.00V 4.8mA 8.0mA
BH7673G
B/C ISO(Composit)
5.00V 4.8mA 8.0mA
NJM2505AF
No Mount
B
7
7
MONITOR PCB
ISO(Compornent)
5.00V 23.0mA 29.0mA
NJM41033
5.0V SY S5
VF = 0.7V MM1 8 5 6 A5 0 N-
8.0V typ 37.4 mA 5.0V ISO(Composit)
5.00V 4.8mA 8.0mA
max 61.0 mA BH7673G
DD8
typ 0.112 W
max 0.183 W LCD BACK LIGHT
OZ5 2 7 ILN
typ 197.6 m A 9.6V LCD B.L
9.60V 140.0mA 140.0mA
max 197.6 mA
max 0.237 W
rBLEN
KEY_ILM SW
8
8
typ 20.0 mA
DD8
1 2
15
A
F
B
F
A
16
1 2
KBUP
DD8
A MOTHER UNIT 5.0V VCC5V
1
1
1258.6mA NJM2886DL3-05 5.0V PICK UP
5.00V 130.0mA 140.0mA
typ 130.0 mA
rVDCONT8 max 140.0 mA
8.0V VD8 max 0.42 W
AN3 3 0 1 2 UA(1 / 2 )
typ 635.0 mA
max 1858.6 m A 8.0V MOTER DRIVER
8.10V 250.0mA 840.0mA
typ 0.56 W BA5839FP
max 1.65 W ( Rush ) 1440.0mA
DD4.3
typ 0.54 W typ 0.248 W
max 0.86 W max 0.073 W
rSUNPWR1 2 5 V
2
2
rVDCONT5
3.3V DVCC3.3
S- 1 1 7 2 B3 3
AVH-280BT/XNUC
Flash-ROM
3.30V 12.0mA 30.0mA
MX25L3206M
iPod CP
3.30V 4.2mA 4.2mA
3
3
337S3959
3.3V BT3.3
MM3 4 1 1 A3 3 N BT(SUNTEC)
4.3V typ 20.0 mA 3.3V X-8075
3.30V 20.0mA 30.0mA
max 30.0 mA
typ 0.020 W
max 0.030 W
1.8V BT 1 . 8V
MM3 4 7 9 A1 8
4.3V typ 65.0 m A 1.8V
1.80V 65.0mA 97.5mA
max 97.5 mA
typ 0.163 W
DD4.3
KBUP
max 0.244 W
4
4
rBT1 8 ON
1 3
1 3
3.3V TUN3.3
DD4.3
KBUP
5
5
3.3V LCD3.3
4.3V
MM3 4 7 9 A3 3 P
typ 294.1 mA 3.3V
B MONITOR PCB LCD MODULE
AVDD 3.30V 10.0mA 15.0mA
max 383.1 mA
typ 0.294 W
max 0.383 W
rLCDPW LCDPW
VDDG 18.00V 0.5mA 1.0mA
R1 2 9 0 K1 0 3 A
typ 153.0 mA
max 171.6 mA
VEEG -6.00V 0.5mA 1.0mA
6
6
typ 0.089 W
max 0.100 W
DVDD 9.20V 30.0mA 35.0mA
AVH-280BT/XNUC
GRADATION
9.20V - 10.0mA
COMDC
9.20V - 6.0mA
REMOTE IC
3.30V 1.2mA 1.5mA
7
7
T-con
3.30V 30.0mA 45.0mA
1.8V LCD1.8V
MM3 5 7 1 A1 8 P
typ 99.9 m A 1.8V
1.80V 99.9mA 150.0mA
max 150.0 mA
typ 0.15 W
max 0.23 W
KBUP
5.0V USB5V
AN3 3 0 1 4 UA
typ 1000.0 mA 5.0V USB
5.00V 1000.0mA 1500.0mA
+ max 1500.0 mA
typ 0.367 W
8
8
max 0.550 W
100uF
rUSBCONT
17
A
F
B
1 2 3 4
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
A
Power ON
BSENS = L
B
ASENS = L
C VD8 : Pin 78
EN8 H
Starts communication
with T-CON.
Starts communication
with SOC.
E
Source ON
SYSPW H
F
Completes power_on operation.
(After that, proceed to each source operation)
AVH-280BT/XNUC
18
1 2 3 4
5 6 7 8
Disc to be used A
CD-DA : TCD-782
DVD-Video : GGV1025 (TDV-582)
Exact judgment cannot be performed if the disk to be used has a crack and dirt.
Be careful of handling of a disk enough.
Execution method
Refer to the following page for the details of the check 1 and the check 2.
Replace the
START
CRG chassis
LD current check
Check2
C
Replace the Error rate check
Is it OK?
No CRG chassis
Yes
Is it OK?
No
Yes
Replace the
Check2 CRG chassis
Error rate check
Ckeck parts
other than PICK UP Finished
AVH-280BT/XNUC
5 6 7 8
19
1 2 3 4
B
MOTHER UNIT (SIDE A)
REFVCC5_1
DVDLD1
[CD]
No. Disc Check Point Criteria for voltage Remarks: LD current
D
2 TCD-782 REFVCC5_1 - CDLD1 449 mV (Ave) 45 mA (Ave)
660 mV (Max) 60 mA (Max)
REFVCC5_1
CDLD1
Notes: Please pay attention to the laser diode damage by static electricity.
AVH-280BT/XNUC
20
1 2 3 4
5 6 7 8
A
Check : RF level
<Check>
Check the RF level.
Status: Playback the test discs on the NORMAL MODE.
RF1
<Check>
Status: Error Rate Mode of DVD TEST MODE
No. Disc Check Point Threshold Remarks (Disc Type) D
AVH-280BT/XNUC
5 6 7 8
21
1 2 3 4
SETUP TIMEOUT ERROR ERROR-02-B5 B5h setup time out by repeting retry X - - X X X -
*1 -xx-xx : Assigning a code number X : Corresponding source X : Cancel the error by operation.
*2 B0-BFh : Notice IDs which are not listed in the LS Mechanism list - : Not correspoinding source - : Error is not cancelled by operation.
* : No setting
C0-FFh : Notice IDs such as ATN which attempt the servo system notice
C
AVH-280BT/XNUC
22
1 2 3 4
5 6 7 8
AVH-280BT/XNUC
5 6 7 8
23
1 2 3 4
15 13 11 9 7 5 3 1
16 14 12 10 8 6 4 2
1. FL+ 9. P. BRAKE
2. FR+ 10. TELMUTE
3. FL- 11. ILM
4. FR- 12. BREM/AANT
E 5. RL+ 13. ACC
6. RR+ 14. REV
7. RL- 15. B.UP
8. RR- 16. GND
AVH-280BT/XNUC
24
1 2 3 4
5 6 7 8
6. SERVICE MODE
6.1 VERSION INFORMATION
Method for Mode IN
A
Display specification
<Eject Lock>
When Eject Lock is on : ON
When Eject Lock is canceled : OFF
Operational description Remote controller key C
Page up NEXT
Page down PREV
Display specification
Description: F
1. SWC TEST MODE : For checking Steering Wheel Control
2. TOUCH PANEL SETTING : For Touch Panel calibration
3. FLICKER ADJUSTMENT : For Flicker adjustment
AVH-280BT/XNUC
5 6 7 8
25
1 2 3 4
Display specification
Top menu
1. SETTING
<Adapter>
When Adapter is connected : Yes
E
When Adapter is not connected : No
<Vehicle marker>
When Adapter setting is “Yes” : Cannot be selected.
When Adapter setting is “No” : Select JAPAN or KOREAN.
AVH-280BT/XNUC
26
1 2 3 4
5 6 7 8
2. AD Measurement result A
Description:
When a key on the steering remote is pressed, the voltage value is
displayed on the screen.
C
AVH-280BT/XNUC
5 6 7 8
27
1 2 3 4
Display specification
Top menu
Description:
When the touch keys do not respond correctly, perform the touch panel calibration by using this test mode.
For the touch panel calibration, perform "1. Effective Area Calibration" and "2. 16 Point Calibration".
AVH-280BT/XNUC
28
1 2 3 4
5 6 7 8
Description:
Touch the target points to calibrate effective area.
First point : Touch the lower right corner of the screen. Second point : Touch the upper left corner of the screen.
Third point : Touch the upper right corner of the screen. Fourth point : Touch the lower left corner of the screen.
AVH-280BT/XNUC
5 6 7 8
29
1 2 3 4
2. 16 Point Calibration
A
16 Point Calibration screen
Description:
Touch the cursor [+] displayed on the screen. By touching it correctly, it disappears and another cursor appears.
By repeating this action 16 times, obtain calibration value of each [+].
When touching the last 17th cursor, calibration values at 16 points and information of normal finish in 17 bytes
are written in Flash ROM and the screen returns to Touch Panel Setting menu by pressing a key.
AVH-280BT/XNUC
30
1 2 3 4
5 6 7 8
4. Calibration Test
Touch the cursor [+] displayed on the screen. By touching it correctly, it disappears and another cursor appears. D
Otherwise, the cursor is displayed in red.
Repeating this action for 4 points and by pressing the last 4th point, “O.K.” is displayed.
AVH-280BT/XNUC
5 6 7 8
31
1 2 3 4
5. Data Initialize
AVH-280BT/XNUC
32
1 2 3 4
5 6 7 8
1. LD ON
2. Error Rate
3. CRG Move Outer B
4. Eject
1. LD ON
< LD ON >
< LD ON > E
Now Running
AVH-280BT/XNUC
5 6 7 8
33
1 2 3 4
ri
< LD ON >
1: Power OFF
2. Error Rate
1. LD ON
C
2. Error Rate
3. CRG Move Outer
4. Eject
AVH-280BT/XNUC
34
1 2 3 4
5 6 7 8
1: Inner Measurement
2: Outer Measurement
3: Middle Measurement
2. Error Rate
Now Running
1: Power OFF
E
Operational description Remote controller key
Return to DVD test mode menu RETURN
Menu enter Band
AVH-280BT/XNUC
5 6 7 8
35
1 2 3 4
1. LD ON
2. Error Rate
3. CRG Move Outer
4. Eject
C
1: DVD Single Layer
2: DVD Dual Layer
3: CD
4: CD-RW
Now Running
E
AVH-280BT/XNUC
36
1 2 3 4
5 6 7 8
1: Power OFF
B
Operational description Remote controller key
Return to DVD test mode menu RETURN
Menu enter Band
ERROR
C
1: Power OFF
Code : 00000000
D
Operational description Remote controller key
Return to test mode menu RETURN
Menu enter Band
AVH-280BT/XNUC
5 6 7 8
37
1 2 3 4
1. Put a software file you want to rewrite in the USB memory stick. (Attention: Store only a file to rewrite.)
Please rewrite SOC and System ucom individually.
CAUTION:
Please rewrite SOC first, and then rewrite System ucom.
If you rewrite the system first, you cannot continue to rewrite the software.
3. Press the RESET key while pressing and holding the “ VOL - ” and “ ” keys at the same time.
RESET
The system starts up in the Software upgrade mode, and the “CAUTION” screen is displayed.
ATTENTION:
If the system starts in other modes than the Software upgrade mode, the keys may not be pressed correctly.
In that case, press the “ VOL - ” and “ ” key correctly and press the RESET key again.
CAUTION:
It takes about two minutes to update SOC and System
ucom. Do not remove the USB memory stick or turn
off the power until the updating procedure is completed.
Removing the USB memory stick or turning off the power
while the update is in progress may damage the software.
AVH-280BT/XNUC
38
1 2 3 4
5 6 7 8
After the “CAUTION” screen, the “Update” screen appears and the updating operation starts automatically.
A
ATTENTION:
With some USB memory sticks, the update cannot be done correctly.
In that case, use other USB memory sticks and try again.
EX) Screen display when SOC upgrade
Confirm that the “It succeeded” screen appears and the updating procedure is completed.
Remove the USB memory stick and turn off the power. C
AVH-280BT/XNUC
5 6 7 8
39
1 2 3 4
Version Check
A
2. Press the RESET key while pressing and holding the “ - ” and “ ” keys at the same time.
RESET
3. Check the software version on the screen after the system starts up in the Version Information mode.
AVH-280BT/XNUC
40
1 2 3 4
5 6 7 8
7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same. A
Monitor Assy
2 2
2 2
3
2 2
2 2
Fig.1
2 1
1
1 Attention at assembly:
When you connect the FFC and 2pin Cable
from TFT LCD, set the 2pin Cable lower side.
Fig.2
AVH-280BT/XNUC
5 6 7 8
41
1 2 3 4
1 1
1 Release the seven latches and then remove
the Holder(2).
B 1
Note:
With this model, the Cushion of Touch
Panel was attached using a jig in the 1 1 1
factory line.
Holder(2)
Fig.3
1
1
Bracket
2
Attention at assembly:
When installing the DVD Mechanism Module,
E
pulling the Bracket to the DVD Mechanism
Module, tighten the screws.
Put the dowels of the DVD Mechanism
Module in the slits of the Bracket securely.
Attention of removing
Don’t remove this screws excluding the
dismantlement of the DVD Mechanism
Module.
F Fig.4
AVH-280BT/XNUC
42
1 2 3 4
5 6 7 8
1
2 Remove the two screws and then remove
the Heat Sink and the Holder. 2 2
1 1
Fig.5
1 1
Holder
D
2
2 2
Bracket
3 Slide the Bracket in the direction indicated
by an arrow and then release the dowel.
E
(Left side and Right side)
3
Attention at assembly:
When installing the Bracket, put the
dowels of the Chassis in the slits of
the Bracket securely.
dowel Fig.6 F
AVH-280BT/XNUC
5 6 7 8
43
1 2 3 4
1 1
1 1
Mother Unit
Fig.7
Sheet
F
Holder Sheet Fig.8
AVH-280BT/XNUC
44
1 2 3 4
5 6 7 8
LCD
Mother Unit "8.2 FLICKER ADJUSTMENT"
Monitor PCB
AVH-280BT/XNUC
5 6 7 8
45
1 2 3 4
A
Method for Mode IN
While pressing [VOL+] + [FORWARD] key, restart the system.
Select and enter "3. FLICKER ADJUSTMENT" on SERVICE TEST MODE Menu screen.
Display specification
Description:
1. SWC TEST MODE : For checking Steering Wheel Control
2. TOUCH PANEL SETTING : For Touch Panel calibration
3. FLICKER ADJUSTMENT : For Flicker adjustment
4. DVD TEST MODE : For DVD mechanism module test
D Display specification
Description:
When the screen is flickering, perform the flicker adjustment by using this test mode.
Minimize the flicker by changing adjustment value.
AVH-280BT/XNUC
46
1 2 3 4
5 6 7 8
AVH-280BT/XNUC
5 6 7 8
47
1 2 3 4
D
18-1 Owner's Manual QRD3356 Not used QRD3357 QRD3358 QRD3359 QRB3356
* 18-2 Quick Start Guide Not used QRD3354 Not used Not used Not used Not used
18-3 Installation Manual Not used QRD3355 Not used Not used Not used Not used
* 18-4 Caution Card Not used CRP1441 Not used Not used Not used Not used
* 18-5 Service Network Not used Not used Not used Not used Not used CRY1305
* 18-6 Warranty Card QRY3001 CRY1376 Not used Not used Not used CRY1304
Owner's Manual,Installation Manual
Part No. Language
E
QRB3356 English
AVH-280BT/XNUC
48
1 2 3 4
5 6 7 8
*QRB3542 English
A
*QRB3543 French
*QRB3544 Italian
*QRB3545 Spanish(Espanol)
*QRB3546 German
*QRB3547 Dutch
*QRB3548 Swedish
*QRB3549 Norwegian
*QRB3550 Finnish
B
*QRB3551 Danish
*QRB3552 Portuguese
*QRB3553 Greek
*QRB3554 Turkish
AVH-280BT/XNUC
5 6 7 8
49
1 2 3 4
9.2 EXTERIOR(1)
A
-1 B
A B -2
D
B
EW5, RI
AVH-280BT/XNUC
50
1 2 3 4
5 6 7 8
AVH-280BT/XNUC
5 6 7 8
51
1 2 3 4
9.3 EXTERIOR(2)
RC, RI, ID
D
A
AVH-280BT/XNUC
52
1 2 3 4
5 6 7 8
AVH-280BT/XNUC
5 6 7 8
53
1 2 3 4
B
A
B
(C)
C (A)
(C)
D
(A)
C (NOTE)
D
(C)
(C)
D
(NOTE) (A)
(A)
(C)
(A) (B)
(A)
(NOTE)
(A) (A)(NOTE)
E E
C
E
B
A
(C) (C)
(A) : GEM1043
(B) : GEM1045
(C) : GEM1024
F
AVH-280BT/XNUC
54
1 2 3 4
5 6 7 8
26 Roller CNW1172
27 Roller CNW1175
28 Arm CNW1177
29 Arm CNW1178
D
30 Gear CNW1180
31 Gear CNW1181
32 Gear CNW1183
33 Rack CNW1184
34 Gear CNW1185
35 Gear CNW1186
36 Gear CNW1187
37 Clamper CNW1190
38 Arm CNW1192 E
39 Holder CNW1193
40 Holder CNW1194
41 Damper CNW2439
42 Damper CNW2440
43 Arm CNW1726
44 Guide CNW3489
45 Arm CNW2241
46 Rack CNW2265
F
47 Gear CNW2287
48 Motor Unit CXC4026
49 Screw Unit CXC8894
AVH-280BT/XNUC
5 6 7 8
55
1 2 3 4
(A)
(C)
(C)
(C)
(A)
(B)
(A) : GEM1043
(B) : GEM1045
(C) : GEM1024
AVH-280BT/XNUC
56
1 2 3 4
10.1 MOTHER UNIT (SENSE)
10. SCHEMATIC DIAGRAM
10. SCHEMATIC DIAGRAM
Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or
"ELECTRICAL PARTS LIST".
5
5
A 9/11
6
AVH-280BT/XNUC
(10A)
FUSE
YEK5001
>
7
7
A 8/11
NOTE :
Symbol indicates a resistor. NM : No Mount
No differentiation is made between chip resistors and The > mark found on some component parts indicates
discrete resistors. the importance of the safety factor of the part.
8
8
A 1/11 A 1/11
57
A
F
B
F
A
58
1
A 4/11
2
2
BT MODULE
AVH-280BT/XNUC
A 9/11
A 10/11
3
3
A 5/11
4
4
A 2/11 A 2/11
5 6 7 8
A 9/11
A 6/11 A 9/11 D
A 9/11
A 3/11 A 3/11
AVH-280BT/XNUC
5 6 7 8
59
F
A
60
1
A 9/11
MODEL
A 11/11 A
B
AVH-280BT/XNUC
AVH-280BT/XNEU5
C AVH-285BT/XNRC
D AVH-285BT/XNRD
E AVH-285BT/XNRI
F AVH-289BT/XNID
A 5/11 A 8/11
C,D,E,F
2
A 2/11
AVH-280BT/XNUC
A 9/11
A 11/11
A 9/11
3
3
A 9/11
A 11/11
4
4
A 9/11 A 10/11
B 1/6 CN5003
A 4/11 A 4/11
10.5 MOTHER UNIT (E.VOL)
A 5/11 MOTHER
(E.VOL)
UNIT
5
5
A 5/11
A 11/11
6
6
AVH-280BT/XNUC
A 5/11
A 7/11
A 2/11 A 4/11
A 4/11
A 7/11
A 5/11
7
7
A 9/11
A 4/11 A 8/11
A 8/11
A 4/11
8
8
A 5/11 A 5/11
61
A
F
B
F
A
62
1
(DDC 2ch)
2
2
AVH-280BT/XNUC
>
3
3
A 3/11 A 9/11
A 9/11
4
4
A 6/11 A 6/11
10.7 MOTHER UNIT (TUNER)
A 7/11 MOTHER UNIT
5
(TUNER)
5
A 5/11
6
6
FM/AM ANTENNA
A 9/11
AVH-280BT/XNUC
7
7
8
8
A 7/11 A 7/11
63
A
F
B
F
A
64
1
A 9/11
A 4/11 A 5/11
2
2
A 5/11
AVH-280BT/XNUC
3
3
A 1/11
A 4/11
4
4
A 8/11 A 8/11
10.9 MOTHER UNIT (ucom)
A 9/11 MOTHER
(ucom)
UNIT
Except A,B
5
5
A 4/11
A 5/11
A 1/11
A 11/11
A 4/11
A 10/11
Except A,B
A 4/11
6
6
A 4/11
AVH-280BT/XNUC
A 8/11
A 11/11
A 3/11
A 10/11
A 7/11
7
7
MODEL
A 4/11 A AVH-280BT/XNUC
B AVH-280BT/XNEU5
C AVH-285BT/XNRC
D AVH-285BT/XNRD
A 2/11 E
F
AVH-285BT/XNRI
AVH-289BT/XNID
A 3/11
A 6/11
A 3/11 A 6/11
A 1/11
A 4/11
A 6/11
8
8
A 9/11 A 9/11
65
A
F
B
F
A
66
1
A 9/11
2
2
A 9/11
AVH-280BT/XNUC
A 4/11 A 9/11
A 2/11
3
3
4
4
A 10/11 A 10/11
10.11 MOTHER UNIT (SOC)
A 11/11MOTHER
(SOC)
UNIT
MODEL Except F
A AVH-280BT/XNUC
B AVH-280BT/XNEU5
5
5
C AVH-285BT/XNRC
D AVH-285BT/XNRD
E AVH-285BT/XNRI
F AVH-289BT/XNID
3
3
A 9/11
A 4/11
6
6
C A 5/11
CN102
A 4/11
AVH-280BT/XNUC
1
7
7
2
8
8
A 11/11 A 11/11
67
A
F
B
F
A
68
1
B 3/6
B 4/6
B 5/6
D
CN5501
B 6/6
2
2
AVH-280BT/XNUC
A 4/11
CN3201
(BACK LIGHT)
TFT LCD
B 2/6
3
3
TOUCH PANEL
B 2/6
4
4
MONITOR KEY UNIT
Consists of
MONITOR PCB
KEY PCB
B 1/6 B 1/6
10.13 MONITOR PCB (LCD_BL)
B 2/6 MONITOR PCB(LCD_BL)
5
5
6
6
AVH-280BT/XNUC
1/6
B 1/6
7
7
B
8
8
B 2/6 B 2/6
69
A
F
B
F
A
70
1
2
2
AVH-280BT/XNUC
3
3
4
4
B 1/6 MONITOR KEY UNIT
Consists of
MONITOR PCB
KEY PCB
B 3/6 B 3/6
10.15 MONITOR PCB(LCDI/F)
B 4/6 MONITOR PCB(LCDI/F)
B 1/6
B 5/6
5
5
TFT LCD
6
6
AVH-280BT/XNUC
7
7
B 1/6
8
8
B 4/6 B 4/6
71
A
F
B
F
A
72
1
B 4/6
B 6/6
2
2
AVH-280BT/XNUC
3
3
B 4/6
4
4
B 1/6 MONITOR KEY UNIT
Consists of
MONITOR PCB
KEY PCB
B 5/6 B 5/6
10.17 MONITOR PCB(ISO)
B 6/6 MONITOR PCB(ISO)
5
5
B 1/6
B 5/6
6
6
AVH-280BT/XNUC
7
7
B 1/6
B 5/6
8
8
B 6/6 B 6/6
73
A
F
B
F
A
74
1
2
2
AVH-280BT/XNUC
PU(DP11)
A 11/11
CN801
3
3
M1
M
CRG(L/E) MOTOR
M2
M
4
4
SPINDLE MOTOR
HOME 12J
C C
10.19 KEY PCB
D KEY PCB
5
5
CN5004
B 1/6
6
6
AVH-280BT/XNUC
7
7
MODEL
A AVH-280BT/XNUC
B AVH-280BT/XNEU5
C AVH-285BT/XNRC
D AVH-285BT/XNRD
E AVH-285BT/XNRI
F AVH-289BT/XNID
8
8
KEY PCB
D D
75
A
F
B
1 2 3 4
10.20 WAVEFORMS
- Mother Unit Note:1. The encircled number denote measuring points in the circuit diagram.
2. Reference voltage: 1.65 V(TD1,FD1)(=VHALF)
2.2 V(RF)(=VREF)
A
In the waveform, it is seeing on the GND standard.
Offset of 1.65 V or 2.2 V is put in.
1RF1 0.2 V/div 100 s/div 1RF1 0.2 V/div 50 s/div 1RF1 0.5 V/div 50 us/div
CDRF(x4CLV) DVDRF(x1.5CLV) DVDRF(BD1mm)
VREF1t
B
2TD1 0.5 V/div 100 us/div 2TD1 0.5 V/div 100 us/div 2TD1 0.5 V/div 500 us/div
Interval FWD(DVD) Interval REV(DVD) Multi 32FWD(DVD)
2TD1 0.5 V/div 500 us/div CH1 : 2TD1 0.5 V/div 10 ms/div CH1 : 2TD1 0.5 V/div 10 ms/div
Multi 32REV(DVD) CH2 : 3LECRGM-LECRGP 2.0 V/div 10 ms/div CH2 : 3LECRGM-LECRGP 2.0 V/div 10 ms/div
Traverse 1001FWD(short)(DVD) Traverse 1001REV(short)(DVD)
D
VHALFt
VHALFt VHALFt
GNDt
GNDt
E
CH1 : 2TD1 0.5 V/div 50 ms/div CH1 : 2TD1 0.5 V/div 50 ms/div CH2 : 3LECRGM-LECRGP 2.0 V/div 200 ms/div
CH2 : 3LECRGM-LECRGP 2.0 V/div 50 ms/div CH2 : 3LECRGM-LECRGP 2.0 V/div 50 ms/div ID search Inside t Outside(DVD)
Traverse 5001FWD(long)(DVD) Traverse 5001REV(long)(DVD)
VHALFt
VHALFt GNDt
GNDt
F GNDt
AVH-280BT/XNUC
76
1 2 3 4
5 6 7 8
2TD1 0.5 V/div 100 ms/div 4FD1 0.5 V/div 100 ms/div 4FD1 0.5 V/div 500 us/div
Play TD(DVD) Focus Close(DVD) Play FD(DVD)
4FD1 0.5 V/div 500 us/div 4FD1 0.5 V/div 500 us/div
Focus Jump L0tL1 Focus Jump L1tL0
VHALFt VHALFt
AVH-280BT/XNUC
5 6 7 8
77
F
A
78
A
For further information for
MOTHER UNIT respective destinations, be sure
to check with the schematic dia-
gram.
1
1
> P303 (A,61,19) Fuse 750 mA CEK1398 2.Viewpoint of PCB diagrams
SIDE B
120 JA3121
5
2
1
2
4
3
6 POWER SUPPLY,SPEAKER
1 5
IC1301
15 25
P.C.Board Chip Part
JA901
3
2 4 6 8 10 12 14 16 18
10 20
FUSE
P3121
1 3 5 7 9 11 13
17
JA3161 REAR VIEW CAMERA
FM/AM ANTENNA 15
4 JA3151 1
4 1
AUX
110 JA2201
D903
6 5 3 2
JA3101
3 2
C1310
USB
C1309
C1312
C1311
C1321
2 3
JA3191
D902 1
C3194 1
4
C2209 2
KN2
1
100 R2203
D2201
D2202
KN3
C3196
3
L2202 C2202
L2201
C2204
L2204
C2203
R2204 C2231 4
L902 1
C2206 C2205
L2203 C905
R2201 C1319 C2417 C2418
C3195 C3191
L2205
C2208
C2207
5 R2407
2
2
C2210 C3197
90
R2402
VL2201
D940
L2206
D101 E
D1303
C940
C1122
C2401
C1120
C1117
C1119
C2216 C2214
C2213
R2209
L2207
AVH-280BT/XNUC
R1303 C2232
R2210
C2219 X2201 R1315
R1304
C2212
C2410
C910
C2402
C2215 IC2201 C2218 C121 C2407
C2217
D941
R917
1
80
R1302
5 1
C2228 R914 C123 5 1 IC1113 IC1111
10
D911
30
D910
D912
R2211
R2212
R2219 IC111 5 5
C2220 1
R1111
1
R1133
15
R1301
C1305 C1114
25
20 C3151 C1113
R2216
R2202
R2412
R1131
R1139
R1113
C1111
C2222
C2221
R913 R912
C1131
C2225 R3151 D2401 L2401
R915
C1136
5
R911 R910 C114 C1138
L2209
C1137
C1132
1
1
C1116
C1140
C1256
70
R1137 IC1132
E
R2221
10
R2220
C1257
5
C1134
1
1
R1204 R1253 R1134
C2229 R1252 C1133
5
E
C1115
R461
R1251 R1132
R1278
C425
R435
C1212 C1112
1
C665 L901
C3125
D401
D402
C1211
60
C1253
R412
BZ401 C1210 1
C409
1
Q3121 Q3123 R1112
R3129
IC1112
C420
C418 R402 C903
5 5 C664 R1120
1 R434
R413
1
KN4 KN7
R433
R462 C408
IC401 C1121
R3133 R3127 C747 C1118
R422 R421 1 5 10 IC741 R1141
Q3122 Q3124 C904
C402
1 1 R420 R419
5 5
CN601 C621
30
R417
105
R418 L601
25
R3132
5
R3130
50 Q302 Q301
100
3
3
C614
10
R404 1 1
R430
R1312
35
20
R436
R611
C410
R445
95
15
R411
1
C407
Q502 C417
R506
C503
90
C412
20
40
15
C746
C405
1
C411
R505 R443
X401
C502 R444 R747
85
R742
C630
C501
25
R509
C413
40
R504 C414 C742
10
R154
45
R508
C745
1
Q501
80
C629
1
R457
30
1
R503 C415
R414 1 5 10 15 C628
1
R429
35
D501
C504 CN401 R162 R156 D302 D301
50
C505
R438
1
40 45 50 C419 C741
55 60 65 70
R746
1
R432
C635
R619
R428
R620
1
C406 C636 R320 R302
R622
R621
C603 C637 C325 C306
R425 C416
R424 C744
R427
R814
R813
C422
R606
C424 C616 R809
C203
R723
5
C3192 R3176 C3193 R151
C651
C650
C649
L721
C657 TD1
IC201 L301
C201 C655 L302
R642 R643 C803 C804
R641 C160 R811
1
C721
C624
L604 IC721
C656
C622
L602
C2907
1
C619
C623
C2906
R2903
20
R2905
C862
C2912 C205 C615
C617
C2902
C861 R801
C2905
R825
R822
10 5 1
CN3201 LECRGP
LECRGM C327 C303
U2901 C847 DVDLD1
1 15 20
C801 CN801
C331
C328 C304 R3179
10 BT MODULE 30
25
20
15
10
5 1
C329
C301
C302
4
C330
4
KN5 P302 KN6
R2911 L861
C658 C802
C659 C2230
A B CN5003 C CN102
A
A MOTHER UNIT
SIDE B
130
5
5
1 120
1
110
1
C1314
C1315
C1317 C1313 C1316 C3127
C1320 C3126
C1318
1
1 D3122 P2201
C3122 P2202
1
C2201
D3103
D3101
C3101
C3170
D3121
100
R3105 R3101 C3171 C3121
D3102 C3102
R3104
R1118
R1115
R3103
R1117
P3161
R3152 R1306
C1308
L3191 C906
D3191
90
1
R3109
R933
1
R1310
R1307
R1308
C907
D3192 Q1304 L930 Q1303
R3107 R3106
R2404
R2405
R931
C2411 P3151 R1305
C1307 D931 E
D930
R1311
R2403 1
C2403 R2406 R932
R2401 C3162 C3167 D1304
R2413 R1313
6
6
R2415
R930
C1219 C1220
C2405
R2417
C2406 R3164 R3168 Q1302
10
C950
IC1201 R963
L1201
R3167
R2419 C960
R3172
R953
R3161
R3166
80
R1203
5
C2409
20
1
1
R2418 R1202
R2416 Q3161 Q3162 D960 D950
C2414 R1201
5
C2226
20
R2411
C1215
25
C3165
C3164 C1216 R960 R952
15
C2413 C1225 C2224
C233
R3169
R3163
R3165
1
R3170
E E
Q960
Q950
C3161
C3169
IC2401 C1224 R2225 R1205
C1223
30
5 R962 R951
10
L2210
AVH-280BT/XNUC
1 C1222 R2217
C1202 R961 R950
IC231
C1201
35
C234 C1203
C1252
70
C212
5
R403
R922
C1204 C1209
C921
C1206
C1227 C1208 R448
40
1
C115
1
IC101
R921
R447
IC211
C920
C1205 C1226
R1277
D231
R1275
C401
L701 C1260 C1207 R2222
C1275
R3102
R1265
Q920
C1266 C1271
C701
1
R1257 C1277
R1259 R1263 R1273
1
C211
R705
C1264
IC701
C1259
C1276
R410 D920 R920
R631 C1261 C427
5
1
Q701
D403
R639 C1273 R453
5
R1256 R1268
R708
5
R1262
C1274
R1274
E R1255 R1260 C117
1
R704 R1254
R1276
R703 R702 C1262 R1264
Q601 C1267 C403
R701
R1269
R629 R630 R644 R1271
R707 C1270
R609 R1270
C609
5
R153
1
R1266
R460
R1267
C311 C902 C1272 C1269 R467 R466
Q602
C610
C654
C653 R452
C611
C612
R638
IC601
50
C315 C313 C308 R637
60 55 50 45 40 D162 D161 D151
R446
65
C627 C662
IC301
R627 C606 C155
30
1
C318
75
R409
C320
C620
25
20
C317 5 R459
5
7
R458
7
C316
80
IC151
C314
C319
R315
C631
R319
40
R415
R616
1
R305 R426 R442
10
15
C151
85
C323 1 C423
R316 R407
15
C604
C638
R304
R306
C605
R303
C168
C157
R317 R803 R634
90
X601 R441
R635 R439
R804 R633 R440
10
C312
R312
R309
R308
R314
95
R805
C601 C602 C167
IC822
5
R806
R604 R3126
100
1
R605
15
R807
R601
30
1
C821 105 110 115 120 125 R603 C2233 R161 D3123 D3124
C660
5
R602
R823 R3124 R3125
C158
C237
10
R808 IC241
R722
R727
C639 C642
15
1
R628 C242 R2909
C641 C646 C648 R623 R626 IC861 R2915
C640 10 29 5 1 C661 R241 R2913
R827 R625 C238 C2911
C841
5
R845
R843
C652
20
R624 C873
R844
10
C845 C2908
R846 R2901
R2916
R802 C872 R2914
C2909
R2902
R2912
R849
R847
C2910
R824 R816
C843
C842
R883
R884
R890
R821
R848
C844
R815 15 20 30 25
E
E
C274 R893 R850
R880
R871
R870
R872 R869
10
E
R895
R889
R862
R899 R887 R863
R861
E
R866
R879
8
8
A A
79
A
F
B
F
A
80
1
B MONITOR PCB SIDE A
A CN3201 D CN5601
80
C5205
R5019 R5020
R5201
C5220
Q5201
E
R5017
70
C5015
C5217
C5437
C5203
R5203 C5011
C5204 L5405 1 5 10 15 20 25 30 35 40 45 50 55 60
R5202
Q5202 C5201
IC5201 C5418
CN5003
E
C5017 R5211 C5202 R5101
IC5001
C5216
C5112
15
C5416
C5111
C5018 D5101
1
20
1 C5101
C5419
C5113
10
R5210 C5218
R5217
C5224
L5101
L5401
1 5
2
2
C5117
R5218
D5102
L5201 C5010 C5407
C5408 R5121
60
R5219
R5216 IC5401 D5103
D5201 C5207
1
R5122 C5114
C5226
1
R5111
C5108
C5219 C5118
R5407
C5103
C5104
R5215 R5113
IC5101
R5214 R5414
C5222
C5223
C5107
R5221
R5205
R5220
R5112
10
AVH-280BT/XNUC
C5206
5
5
15
C5331 C5105 C5102
R5103
C5341
C5106
L5301
R5331
C5343
C5409 R5415
1
C5332 20
R5329
R5115
R5116
R5114
C5305 X5401
R5337
R5422
R5107
R5409
R5411
C5330 R5007 R5008
E R5330
50
Q5301
C5425
R5108
R5421
C5426
R5301
R5328
R5124
R5117
R5123
R5302 R5303 C5329
R5518
R5520
1
R5519
C5110
R5110
R5333
R5109
R5338
C5109
C5306 C5340 C5404
C5116
C5344
R5339 R5423 E
R5424 R5522
R5419
R5417
C5327 R5408
R5412
R5410
R5304 C5304
C5346
E
C5307
R5334
C5339 C5328
R5418
C5352
5
1
C5309 R5336 L5302 IC5402
R5341
C5310 R5307 C5338 C5342
R5308 R5335 R5340 R5346 40 35 30 25
C5311 C5348 C5351 C5347 C5345 C5349 C5012
20
10
C5312 R5309
R5310 1 5 10 15 20 25 30 35 40 45 50 55 60
1
40 C5313
45
R5403
15
C5314 R5311 C5414
R5312
C5315 CN5301
50
1
R5313
10
R5314 C5316
R5425
C5432
C5013 CN5004
C5317 C5422 R5433
5
55
C5318 R5315
5
R5316 C5423 R5432
1
C5319 D5006
C5421 R5437
R5426
60
R5317
1
R5318 C5320
C5420 R5436 D5005
C5321 65 70 75 80
R5501
1
C5322 R5319 C5016
R5320
C5323
R5321
30 C5324
1
R5322
C5325 R5428
R5323 R5016
R5427 1 1 C5021
3
3
C5019 C5022
R5014 R5429
R5015
C5020
D5003
D5002
D5001
R5002
R5003
C5007
C5004
C5005
R5004
C5006
R5005
D5004
20 C5023 C5024
TFT LCD 1
CN5001
CN5002
TH5001 C5008 1
10
4
(BACK LIGHT)
B B
B MONITOR PCB SIDE B
5
5
80
D5203 D5202
1
1 C5211
C5210
C5002 C5003
R5204
C5212
70
C5214
C5221 C5208
C5215
R5213 1
R5013 R5012
D5204
R5207
R5212
R5208 C5213
R5206
R5209
C5001
R5514
R5516
R5515
R5102
C5503
C5507
C5508
C5504
C5505
C5506
60
R5118 C5209
R5119 R5413
6
6
R5120 C5510
C5511 C5509
R5104 R5106
C5115 C5225
R5416
R5521
C5515 C5514
R5105
C5513
5 1
IC5502 C5501
IC5501
1
50
AVH-280BT/XNUC
C5502
L5503
R5510
10
R5517
R5001 R5402 R5401
C5512
R5506 C5337
R5525
L5501
L5502
R5513
R5523
R5511
R5512
R5524
C5402
C5439 R5406
E
R5327
Q5501 E E E C5435 C5424 C5401
C5333
C5334
C5335
C5405 R5404
Q5504
C5350
Q5502
R5345
C5406 R5405
C5403
C5336
Q5503
R5507 L5505 C5433
C5438 R5326 R5324
40
C5415
L5403
C5413
C5412
C5516
C5518
R5509
C5517
C5434
R5508
R5342
L5504
L5506
L5404 C5427
C5302
R5431 C5430
R5347
R5430 C5428 C5411
R5018
C5417
L5402
R5435 C5429
R5325
R5343
R5344
C5436
R5434 C5431
C5301
30
7
7
20
10
8
8
B B
81
A
F
B
1 2 3 4
A
C RELAY UNIT SIDE A
PU UNIT (DP11)
70
B
VR101
1
20 CN101
R101 15
60
VR102
10
1
5
1 1
C103
HOME
C101 M2 SPINDLE MOTOR
50 S101
C102
GREEN
40
WHITE
C106
RED
30 BLK
C108 C109
D C114
20
10
CN102
Y 30 25 20 15 10 5 1
A CN801
E
0 X 10 20 30 40 50 60 70 80
C C
AVH-280BT/XNUC
82
1 2 3 4
5 6 7 8
70
B
C104
60
50
40
C111
S103 30
1
R102 C113
D
C110
20
S102
1
12EJ
10
R103
Y
E
80 70 60 50 40 30 20 10 X 0
C C
AVH-280BT/XNUC
5 6 7 8
83
1 2 3 4
A
D KEY PCB SIDE A
D KEY PCB SIDE B
RESET EJECT
1
1
C5602
S5602
90 S5601 90
IC5601
B 1
R5608
R5601
S5604
VOL-
S5605
70 70
1
60 60
MUTE
S5603
1
50
D5601
50 HOME
1
1
C5601
S5609
B CN5004
5
D DISP R5603
40 40
10
1
S5608 CN5601
30 30
R5604
FORWARD
R5605
20
1
E 20 S5606
REVERSE
1
S5607
10 10
Y
Y
0 X X 0
10 20 20 10
F
D D
AVH-280BT/XNUC
84
1 2 3 4
5 6 7 8
Example) IC 301 is on the point (face A, 91 of x-axis, and 111 of y-axis) of the corresponding
PC board.
IC 301 (A, 91, 111) IC NJM2068V
The expression of the unit in this manual is shown by u instead of . Please do not make a mistake.
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
A:AVH-280BT/XNUC MISCELLANEOUS
A
Unit Number : QWM4221(A)
IC 1113
IC 1131
IC 1132
(A,126,78)
(A,123,69)
(A,131,72)
IC
IC
IC
NJM2505AF
NJM41050V
NJM41010F1
Unit Number : QWM4220(B) IC 1201 (B,88,74) IC PM9012A
Unit Number : QWM4223(C) IC 1251 (B,100,62) IC NJM8065RB1
Unit Number : QWM4224(D) IC 1252 (B,76,63) IC NJM8065RB1
IC 1301 (A,86,120) IC PA2032A
Unit Number : QWM4225(E) IC 2201 (A,17,78) IC TEF6686HN
F
Unit Number : QWM4226(F)
IC 2401 (B,159,79) DC/DC CONV IC AN33014UA
Unit Name : Mother Unit Q 301 (A,158,45) Transistor ATP112-H
Q 302 (A,146,45) Transistor ATP112-H
AVH-280BT/XNUC
5 6 7 8
85
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
Q 501 (A,12,40) Chip Transistor HN1C03FU L 601 (A,121,53) Inductor LCTC2R2K1608
Q 502 (A,22,45) Transistor UMF5N
L 602 (A,84,23) Inductor LCTC2R2K1608
Q 503 (A,22,40) Transistor UMF5N L 603 (A,87,22) Inductor LCTC2R2K1608
A
Q 601 (B,128,59) Transistor EMD53 L 604 (A,90,24) Inductor LCTC2R2K1608
Q 602 (B,128,55) Transistor EMH53 L 721 (A,102,27) Inductor CTF1786
Q 701 (B,113,61) Transistor(A,B,C,D,E) LSAR523UB L 741 (A,106,31) Inductor CTF1786
Q 841 (B,116,13) Transistor 2SAR293PGZE
L 901 (A,146,61) Choke Coil 10 uH CTH1486
Q 842 (B,123,13) Transistor 2SAR293PGZE L 902 (A,53,95) Choke Coil CTH1621
Q 843 (B,142,9) Transistor LSCR523UB L 2202 (A,13,95) Inductor CTF1389
Q 844 (B,143,15) Transistor LSCR523UB L 2204 (A,21,98) Inductor LCMAR27J1608
Q 845 (B,136,15) Transistor LSCR523UB L 2206 (A,13,89) Inductor LCYC150K1608
Q 846 (B,136,11) Transistor LSCR523UB
L 2401 (A,157,72) SMD SPL Inductor CTH1524
Q 910 (A,43,70) Chip Transistor HN1C01FU L 2402 (A,162,71) Inductor CTF1793
B Q 920 (B,41,64) Transistor LTC014EEB L 3191 (B,151,89) Inductor CTF1713
Q 930 (B,50,85) Transistor LSCR523UB X 401 (A,31,46) Crystal Resonator 12.500 MHz CSS1839
Q 950 (B,34,75) Transistor LSAR523UB X 601 (B,131,39) Resonator 27.000 MHz CSS1768
Q 1251 (A,91,65) Transistor LSCR523UB
X 2201 (A,27,83) Crystal Resonator 9.216 MHz CSS1867
Q 1301 (A,70,86) Transistor LSCR523UB >P303 (A,61,19) Fuse 750mA CEK1398
Q 1302 (B,69,84) Transistor RN4987 P 2202 (B,19,102) Surge Absober IMSA-6803-01Y900
Q 1304 (B,73,86) Chip Transistor RN1903 P 3121 (A,32,111) Poly Switch FSMD075-24R
Q 3121 (A,28,59) Transistor(C,D,E,F) EMD53 P 3151 (B,122,87) Poly Switch FSMD075-24R
Q 3122 (A,28,53) Transistor(C,D,E,F) EMD53
P 3161 (B,122,93) Poly Switch FSMD075-24R
Q 3123 (A,32,59) Transistor(C,D,E,F) EMD53 BZ401 (A,20,60) Buzzer CPV1062
Q 3124 (A,32,53) Transistor(C,D,E,F) EMD53 U 2901 (A,45,14) BT Module CWX4772
C Q 3161 (B,109,80) Transistor EMH53 CN801 (A,114,10) 30P Connector VKN1620
Q 3162 (B,102,80) Transistor EMH53 CN2901 (A,45,14) B TO B Connector CKS6346
BD
Unit Number : QWM4236(A,C,D,E,F)
R
R
R
5009
5017
5018
(A,105,50)
(A,90,71)
(B,97,35)
RS1/16SS472J
RS1/16SS0R0J
RS1/16SS0R0J
R 5019 (A,90,72) RS1/16SS0R0J
Unit Number : QWM4234(B)
Unit Name : Monitor Key Unit R 5102 (B,137,61) RS1/16SS102J
R 5103 (A,130,55) RS1/16SS0R0J
MISCELLANEOUS R 5104 (B,137,58) RS1/16SS104J
D R 5105 (B,133,54) RS1/16SS104J
IC 5001 (A,64,66) Regulator IC MM3571A18P R 5106 (B,130,58) RS1/16SS102J
IC 5101 (A,136,55) Display IC OZ527ILN
IC 5201 (A,32,64) DC/DC CONV IC R1290K103A R 5107 (A,132,52) RS1/16SS223J
IC 5401 (A,69,57) Flash ROM Unit CWJ2031 R 5108 (A,133,50) RS1/16SS563J
IC 5402 (A,71,38) Display IC TW8832SAT-LB1-GRSH R 5109 (A,137,50) RS1/16SS104J
R 5110 (A,138,50) RS1/16SS0R0J
IC 5601 (A,7,93) IR RC Rec Module PNJ4833M R 5111 (A,140,59) RS1/16SS102J
Q 5001 (A,105,47) Transistor LSCR523UB
Q 5201 (A,37,71) Transistor LTC024EEB R 5112 (A,140,58) RS1/16SS2702D
Q 5202 (A,25,66) Transistor 2SAR502UB R 5113 (A,142,58) RS1/16SS3901D
Q 5301 (A,26,50) Transistor LSAR523UB R 5118 (B,139,61) RS1/16SS1004D
R 5119 (B,139,60) RS1/16SS0R0J
E
Q 5302 (A,29,46) Transistor LSCR523UB R 5120 (B,140,59) RS1/16SS1503D
D 5101 (A,115,65) Diode CRG03
D 5102 (A,134,62) Diode RB060M-30 R 5122 (A,133,58) RS1/8SQ2R2J
D 5103 (A,115,60) Diode CRG03 R 5201 (A,35,70) RS1/16SS8201D
D 5201 (A,28,57) Schottky Diode DB2J41100 R 5202 (A,35,68) RS1/16SS6800D
R 5203 (A,36,69) RS1/16SS1502D
D 5202 (B,26,73) Schottky Diode DB3S308F0 R 5205 (A,37,58) RS1/16SS0R0J
D 5203 (B,29,73) Schottky Diode DB3S308F0
D 5204 (B,24,69) Schottky Diode DB3S308F0 R 5206 (B,26,65) RS1/16SS9102D
D 5601 (A,4,45) Blue LED(A,C,D,E,F) FM-3528BK-470M R 5207 (B,34,68) RS1/16SS1802D
D 5601 (A,4,45) Red LED(B) FM-3528SXK620H08 R 5208 (B,35,66) RS1/16SS203J
R 5209 (B,36,63) RS1/16SS104J
F L 5101 (A,130,63) Inductor ATH7068 R 5210 (A,27,64) RS1/16SS103J
L 5201 (A,27,61) Choke Coil 22 uH CTH1426
L 5301 (A,35,53) Inductor CTF1765 R 5211 (A,38,66) RS1/16SS472J
L 5402 (B,73,36) Inductor CTF1547 R 5212 (B,31,68) RS1/16SS1003D
AVH-280BT/XNUC
92
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 5213 (B,32,69) RS1/16SS9101D R 5414 (A,64,57) RS1/16SS473J
R 5214 (A,26,57) RS1/10SR2R2J R 5415 (A,74,54) RS1/16SS473J
R 5216 (A,37,60) RS1/16SS1203D R 5416 (B,66,57) RS1/16SS473J
A
R 5217 (A,37,62) RS1/16SS3001D R 5417 (A,75,48) RS1/16SS330J
R 5218 (A,39,62) RS1/16SS1502D R 5418 (A,66,45) RS1/16SS330J
R 5219 (A,36,60) RS1/16SS472J R 5419 (A,71,48) RS1/16SS330J
R 5220 (A,33,58) RS1/16SS0R0J R 5420 (A,78,50) RS1/16SS101J
R 5301 (A,20,50) RS1/8SQ0R0J R 5421 (A,77,48) RS1/16SS0R0J
AVH-280BT/XNUC
94
1 2 3 4