Professional Documents
Culture Documents
T390HVN01 0-Auo
T390HVN01 0-Auo
0 Product Specification
Rev.2.0
()Preliminary Specifications
*)Final Specifications ver. 2.0
(*
T390HVN01.0 Product Specification
Rev.2.0
Contents
No
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
3 ELECTRICAL SPECIFICATION
4 OPTICAL SPECIFICATION
7 INTERNATIONAL STANDARD
8 PACKING
9 PRECAUTION
9-5 STORAGE
Record of Revision
Version Date Page Description
Final 2012/2/14 First release
update 2012/3/13 Update drawing and LVDS pin assignment
2012/3/23 Update LVDS connector
T390HVN01.0 Product Specification
Rev.2.0
1. General Description
This specification applies to the 38.5 inch Color TFT-LCD Module T390HVN01.0. This LCD module has a TFT
active matrix type liquid crystal panel 1,920x1,080 pixels, and diagonal size of 38.5 inch. This module supports
1,920x1,080 mode. Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical
stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot.
The T390HVN01.0 has been designed to apply the 8-bit 2 channel LVDS interface method. It is intended to
support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very
important.
General Information
3. Electrical Specification
The T390HVN01.0 module requires power input which is employed to power the LCD electronics and to drive the
TFT array and liquid crystal.
LVDS Differential Input High Threshold Voltage VTH +100 -- +300 mVDC 4
Interface
Differential Input Low Threshold Voltage VTL -300 -- -100 mVDC 4
3-1.2: AC Characteristics
Value
Parameter Symbol Unit Note
Min. Typ. Max
Receiver Clock : Spread Spectrum Fclk Fclk
Fclk_ss -- MHz 6
Modulation range -3% +3%
Receiver Clock : Spread Spectrum
LVDS Fss 30 -- 200 KHz 6
Modulation frequency
Interface
Receiver Data Input Margin
Fclk = 85 MHz tRMG -0.4 -- 0.4 ns 7
Fclk = 65 MHz -0.5 -- 0.5
Note :
1. Test Condition:
(1) VDD = 12.0V
(2) Fv = Type Timing, 60Hz, 120Hz or Other
(3) Fclk= Max freq.
T390HVN01.0 Product Specification
Rev.2.0
(4) Temperature = 25 ℃
(5) Typ. Input current : White Pattern
Max. Input current: Heavy loading pattern defined by AUO
>> refer to “Section:3.3 Signal Timing Specification, Typical timing”
10%
GND
400 µs
3. Test Condition:
(1) The measure point of VRP is in LCM side after connecting the System Board and LCM.
(2) Under Max. Input current spec. condition.
4. VICM = 1.25V
LVDS -
V IC M V TH
|V ID |
V TL
LVDS +
GND
|V ID |
0V
|V ID |
5. The measure points of VIH and VIL are in LCM side after connecting the System Board and LCM.
6. LVDS Receiver Clock SSCG (Spread spectrum clock generator) is defined as below figures.
1/FSS
Fclk_
Fclk_ss(
ss(max)
max)
Fclk
Fclk_
Fclk_ss(
ss(min)
min)
T390HVN01.0 Product Specification
Rev.2.0
7. Receiver Data Input Margin
Rating
Parameter Symbol Unit Note
Min Type Max
Input Clock Frequency Fclk Fclk (min) -- Fclk (max) MHz T=1/Fclk
Input Data Position0 tRIP1 -|tRMG| 0 |tRMG| ns
Input Data Position1 tRIP0 T/7-|tRMG| T/7 T/7+|tRMG| ns
Input Data Position2 tRIP6 2T/7-|tRMG| 2T/7 2T/7+|tRMG| ns
Input Data Position3 tRIP5 3T/7-|tRMG| 3T/7 3T/7+|tRMG| ns
Input Data Position4 tRIP4 4T/7-|tRMG| 4T/7 4T/7+|tRMG| ns
Input Data Position5 tRIP3 5T/7-|tRMG| 5T/7 5T/7+|tRMG| ns
Input Data Position6 tRIP2 6T/7-|tRMG| 6T/7 6T/7+|tRMG| ns
tRIP2
tRIP3
tRIP4
tRIP5
tRIP6
tRIP0
tRIP1
LVDS-Rx
Rx3 Rx2 Rx1 Rx0 Rx6 Rx5 Rx4 Rx3 Rx2 Rx1 Rx0 Rx6
Input Data
LVDS-Rx
Input Clock Vdiff = 0V
1/Fclk=T
T390HVN01.0 Product Specification
Rev.2.0
3-2 Interface Connections
LVDS interface requirement
CN2 : 187059-51221-1 ((P-TWO)
PIN Symbol Description PIN Symbol Description
1 N.C. AUO Internal Use Only 26 N.C. AUO Internal Use Only
2 N.C. AUO Internal Use Only 27 N.C. AUO Internal Use Only
3 N.C. AUO Internal Use Only 28 CH2_0- LVDS Channel 2, Signal 0-
4 N.C. AUO Internal Use Only 29 CH2_0+ LVDS Channel 2, Signal 0+
5 N.C. AUO Internal Use Only 30 CH2_1- LVDS Channel 2, Signal 1-
6 N.C. AUO Internal Use Only 31 CH2_1+ LVDS Channel 2, Signal 1+
Open/High(3.3V) for NS,
7 LVDS_SEL 32 CH2_2- LVDS Channel 2, Signal 2-
Low(GND) for JEIDA
8 N.C. No connection 33 CH2_2+ LVDS Channel 2, Signal 2+
9 N.C. No connection 34 GND Ground
10 N.C. No connection 35 CH2_CLK- LVDS Channel 2, Clock -
11 GND Ground 36 CH2_CLK+ LVDS Channel 2, Clock +
12 CH1_0- LVDS Channel 1, Signal 0- 37 GND Ground
13 CH1_0+ LVDS Channel 1, Signal 0+ 38 CH2_3- LVDS Channel 2, Signal 3-
14 CH1_1- LVDS Channel 1, Signal 1- 39 CH2_3+ LVDS Channel 2, Signal 3+
15 CH1_1+ LVDS Channel 1, Signal 1+ 40 CH2_4- No connection
16 CH1_2- LVDS Channel 1, Signal 2- 41 CH2_4+ No connection
17 CH1_2+ LVDS Channel 1, Signal 2+ 42 N.C. AUO Internal Use Only
18 GND Ground 43 N.C. No connection
19 CH1_CLK- LVDS Channel 1, Clock - 44 GND Ground
20 CH1_CLK+ LVDS Channel 1, Clock + 45 GND Ground
21 GND Ground 46 GND Ground
22 CH1_3- LVDS Channel 1, Signal 3- 47 N.C. No connection
23 CH1_3+ LVDS Channel 1, Signal 3+ 48 VDD Power Supply, +12V DC Regulated
24 CH1_4- No connection 49 VDD Power Supply, +12V DC Regulated
25 CH1_4+ No connection 50 VDD Power Supply, +12V DC Regulated
51 VDD Power Supply, +12V DC Regulated
Note: N.C. : please leave this pin unoccupied. It can not be connected by any signal
(Low/GND/High).
T390HVN01.0 Product Specification
Rev.2.0
LVDS Option = High/Open NS
P re vio u s C y cle C u rren t C yc le N e xt C yc le
C lo ck
C H x_0+ R1 R0 G0 R5 R4 R3 R2 R1 R0 G0
C H x_0-
C H x_1+ G2 G1 B1 B0 G5 G4 G3 G2 G1 B1
C H x_1-
C H x_2+
C H x_2- B3 B2 DE NA NA B5 B4 B3 B2 DE
C H x_3+
C H x_3- R7 R6 NA B7 B6 G7 G6 R7 R6 NA
Note: x = 1, 2, 3, 4…
C lo ck
CH x_0+ R3 R2 G2 R7 R6 R5 R4 R3 R2 G2
CH x_0-
CH x_1+ G4 G3 B3 B2 G7 G6 G5 G4 G3 B3
CH x_1-
CH x_2+
CH x_2- B5 B4 DE NA NA B7 B6 B5 B4 DE
CH x_3+
CH x_3- R1 R0 NA B1 B0 G1 G0 R1 R0 NA
Note: x = 1, 2, 3, 4…
T390HVN01.0 Product Specification
Rev.2.0
3-3 Signal Timing Specification
This is the signal timing required at the input of the user connector. All of the interface signal timing should be
satisfied with the following specifications for its proper operation.
Notes:
(1) Display position is specific by the rise of DE signal only.
st st
Horizontal display position is specified by the rising edge of 1 DCLK after the rise of 1 DE, is displayed on the
left edge of the screen.
(2)Vertical display position is specified by the rise of DE after a “Low” level period equivalent to eight times of
st st
horizontal period. The 1 data corresponding to one horizontal line after the rise of 1 DE is displayed at the top
line of screen.
(3)If a period of DE “High” is less than 1920 DCLK or less than 1080 lines, the rest of the screen displays black.
(4)The display position does not fit to the screen if a period of DE “High” and the effective data period do not
synchronize with each other.
T390HVN01.0 Product Specification
Rev.2.0
Tv M pixel
Tblk(v) Tdisp(v)
N L in e
Th
DE
RGB Line Invalid Data Line Line Line Line Line Invalid Data
N 1 2 3 4 N
Data
CLK
Th
Tclk
Tdisp(h) Tblk(h)
DE
3-4 Signal Timing Waveforms
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH1 M-7 M-5 M-3 M-1
Invalid Data
1 3 5 7 9 11 M-5 M-3 M-1
Invalid Data
1 3
Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel Pixel
CH2 M-6 M-4 M-2 M
Invalid Data
2 4 6 8 10 12 M-4 M-2 M
Invalid Data
2 4
T390HVN01.0 Product Specification
Rev.2.0
3-5 Color Input Data Reference
The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color;
the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
90% 90%
Pow er Supply For LCD
VD D (+ 12 V ) 10% 10% 10%
G ND
t1 t2 t5 t6 t7
t3 t4
Backlight on / off
control signal
( VBLO N ) GND
CM O S Interface Signal t8 t9
( LVD S _ SE L , ....... )
G ND
Values Unit
Parameter
Min. Type. Max. Min.
t1 0.4 --- 30 ms
t2 0.1 --- 50 ms
t3 450 --- --- ms
*1
t4 0 --- --- ms
t5 0 --- --- ms
*2
t6 --- --- --- ms
t7 500 --- --- ms
*3
t8 10 --- 50 ms
t9 0 --- --- ms
Parameter Values Unit --- ms
Min. Type. --- ms
Note:
(1) t4=0 : concern for residual pattern before BLU turn off.
(2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value)
(3) When CMOS Interface signal is N.C. (no connection), opened in Transmitted end, t8 timing spec can be
negligible.
T390HVN01.0 Product Specification
Rev.2.0
3-7 Backlight Power Specification
CN1: CI0112M1HRL-NH(CviLux)
Spec
Item Symbol Condition Unit Note
Min Typ Max
Lamp voltage VL 673 748 823 Vrms
Lamp current IL - 16.5 17 mArms
Lamp frequency fL 35 - 80 kHz
At 0℃ - - 1485 Vrms
Starting voltage Vs
At 25℃ - - 1188 Vrms
Delayed discharge time TD - - 1.0 sec
Life time TL 50K - - hr
Unsymmetrical ratio UR - - 10% -
Note 1.
Crest factor C.F. 2 − 10% 2 2 + 10% -
The above characteristics are measured under the conditions:
Ambient temperature: 25±2℃, Relative Humidity: 65±20%RH.
4. Optical Specification
Optical characteristics are determined after the BLU unit has been ‘ON’ (note 1.) and stable for approximately 45
minutes in a dark environment at 25°C. The values s pecified are at an approximate distance 50cm from the LCD
surface at a viewing angle of φ and θ equal to 0°.
Fig.1 presents additional information concerning the measurement equipment and method.
SR3 or equivalent
Values
Parameter Symbol Condition Unit Notes
Min. Typ. Max
Contrast Ratio CR 2400 3000 -- 1,2
Surface Luminance 2
LWH 280 350 -- cd/m 1,3
(White)
With AUO Module
Luminance Variation δWHITE(9P) -- -- 1.33 1,4
Response Time (G to G) Tγ -- 6.5 -- Ms 5
Color Gamut NTSC 72 %
Color Chromaticity 6
Red RX 0.640
RY 0.330
Green GX 0.300
With CS-1000T
GY 0.600
Standard light source “C” Typ.-0.03 Typ.+0.03
Blue BX 0.144
BY 0.060
White WX 0.280
WY 0.290
Viewing Angle 7
x axis, right(φ=0°) θr -- 89 -- degree
x axis, left(φ=180°) θl With AUO Module -- 89 -- degree
y axis, up(φ=90°) θu -- 89 -- degree
y axis, down (φ=270°) θd -- 89 -- degree
3. Surface luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. For more information see FIG 2. LWH=Lon5 where Lon5 is the luminance with all pixels
displaying white at center 5 location.
FIG. 2 Luminance
H/2 1 2 3
4 5 6 H
7 8
H/6
V/6 V/2
Measured Target
Response Time 0% 25% 50% 75% 100%
0% 0% to 25% 0% to 50% 0% to 75% 0% to 100%
25% 25% to 0% 25% to 50% 25% to 75% 25% to 100%
Start 50% 50% to 0% 50% to 25% 50% to 75% 50% to 100%
75% 75% to 0% 75% to 25% 75% to 50% 75% to 100%
100% 100% to 0% 100% to 25% 100% to 50% 100% to 75%
The response time is defined as the following figure and shall be measured by switching the input signal for
“any level of grey(bright) “ and “any level of gray(dark)”.
Any level of gray (Bright) Any level of gray (Dark) Any level of gray (Bright)
0%, 25%, 50%, 75%, 100% 0%, 25%, 50%, 75%, 100%
90%
Photodetector
Output
10%
0%, 25%, 50%, 75%, 100%
Time
T γ (F) T γ (R)
6. Light source here is the standard light source “C” which is defined by CIE and driving voltages are based on
suitable gamma voltages. The calculating method is as following:
A. Measure the “Module” and “BLU” optical spectrums (W, R, G, B) of AUO T390HVN01.0
B. Calculate cell spectrum from “Module” and “BLU” spectrums.
C. Calculate color chromaticity by using cell spectrum and the spectrum of standard light source “C”.
7. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For
more information see FIG4.
5. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T390HVN01.0. In addition the figures in the
next page are detailed mechanical drawing of the LCD.
Horizontal 898.92 mm
Vertical 525.33 mm
Outline Dimension
Depth (Dmin) 32.93 mm
Weight 6500 g
7. International Standard
7.1 Safety
(1) UL 60950-1, UL 60065; Standard for Safety of Information Technology Equipment Including
electrical Business Equipment.
(2) IEC 60950-1 : 2001, IEC 60065:2001 ; Standard for Safety of International Electrotechnical
Commission
7.2 EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI),
1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.” European Committee for Electrotechnical Standardization. (CENELEC),
© Copyright AUO Optronics Corp. 2011 All Rights Reserved. Page 24 / 29
T390HVN01.0 Product Specification
Rev.2.0
1998
8. Packing
8-1 DEFINITION OF LABEL:
A. Panel Label:
*xxxxxxxxxxxx-xxxx*
AUO Internal Use
Panel Unique ID
AU Optronics
B. Carton Label:
QTY : 6
T390HVN01.0
97.39T01.XXX
Specification
Item Packing Remark
Qty. Dimension Weight (kg)
Box = 2.7kg
1 Packing BOX 6pcs/box 970(L)*560(W)*605(H) 43
Cushion=1.76kg
Stretch film
Corner angle
Pallet
9-5 STORAGE
When storing open cell units as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the open cell unit to sunlight or fluorescent light. Keep the
temperature between 5℃ and 35℃ at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they
be stored in the container in which they were shipped.