Professional Documents
Culture Documents
3 3⁄4"
(95.3) 1 7⁄8"
(47.6)
Hardware
Nuts &
3 1⁄2"
(88.9) 2"
(50.8)
General
Fittings
R-As shown
L-Opposite hand
P2224 P2225
Supports
1 7⁄8" 3 3⁄4"
(47.6) (95.3)
Electrical
Fittings
3 7⁄8"
3 7⁄ 8" (98.4)
(98.4)
Concrete
Inserts
Wt/C 115 Lbs (52.2 kg) Wt/C 155 Lbs (70.3 kg)
11⁄4" Framing
P2227 P2228
System
5 13 32 "
5 13
32 " (137.3)
(137.3) 1 7⁄8"
(47.6)
1 7⁄8"
(47.6)
Framing
System
3 7⁄ 8"
2" (98.4)
(50.8)
13⁄16"
Spec. Metals
& Fiberglass
Wt/C 113 Lbs (51.3 kg) Wt/C 177 Lbs (80.3 kg)
102
Return to #12 TOC Return to Fittings TOC
Goto to Main PDF Menu
GENERAL FITTINGS
Channels FOR 15⁄8" (41 MM) WIDTH SERIES CHANNEL
Page
1 5/8"
Flat Plate
Fittings 82
Ninety Degree
Fittings 86
Hardware
Nuts &
Angular
Fittings 93
“Z” Shape
Fittings 94
“U” Shape
General
Fittings
Fittings 96
Wing Shape
Fittings 101
Post Bases
105
Pipe/Conduit
Supports
Brackets and
106
Braces
Beam Clamps
112
Electrical
Trolleys
Fittings
122
Special Application
124
Fittings
End Caps
126
Concrete
Inserts
Partition and
127
Display Fittings
Fittings, unless noted, are made III SC1; Hot-dipped galvanized (HG),
System
5
BOLT 1⁄4" 5⁄16" 3⁄8" 1⁄2" ⁄8" 3⁄4"
from hot-rolled, pickled and oiled conforming to ASTM A123 or A153 SIZE 20 18 16 13 11 10
steel plates, strip or coil, and and plain (PL). FOOT 6 11 19 50 100 125
conform to ASTM specifications LBS.
A575, A576, A635, or A36. The APPLICATION N.m 8 15 25 70 135 170
Framing
fitting steel also meets the physical All parts drawings illustrate only one
System
smooth surface free from scale. possible. The channels shown in the inches. Metric dimensions are shown
illustrations are P1000, 15⁄8" square, in parenthesis or as noted. Unless
Many fittings are also available in except where noted otherwise. All noted, all metric dimensions are in
Spec. Metals
& Fiberglass
stainless steel, aluminum and 9⁄16" diameter holes use 1 ⁄2" x 15⁄16" hex millimeters and rounded to one
fiberglass. Consult factory for head cap screws and 1⁄2" nuts – P1010, decimal place.
ordering information. P4010 or P5510 – depending on the
channel used. Nuts and bolts are not DESIGN LOAD
FINISHES included with the fitting and must be Design load data, where shown, is
Fittings are available in: Perma- ordered separately. based on the ultimate strength of the
Index
80
Return to #12 TOC
Goto to Main PDF Menu
Channels
DESIGN LOAD DATA FOR TYPICAL
1 5/8"
UNISTRUT CHANNEL CONNECTIONS
Hardware
Nuts &
LOAD LOAD LOAD LOAD LOAD
General
Fittings
P1325 P1458
Channel
P1026 P1026 P2235 P1579 P1346
Thickness
Lbs kN Lbs kN Lbs kN Lbs kN Lbs kN
Pipe/Conduit
Supports
12 ga. 1500 6.7 1000 4.4 2000 8.9 1500 6.7 2000 8.9
14 ga. 1000 4.4 650 2.9 2000 8.9 1000 4.4 1500 6.7
16 ga. 750 3.3 500 2.2 1500 6.7 1000 4.4 900 4.0
Electrical
Fittings
90o Fittings (When used in position shown) Flat Plate Fittings
Concrete
Inserts
LOAD
11⁄4" Framing
Channel
System
P2484 P1068 P1326 P1346 P1065
Thickness
Lbs kN Lbs kN Lbs kN Lbs kN Lbs kN
12 ga. 3000 13.3 500 2.2 500 2.2 1200 5.3 1000 4.4
14 ga. 2000 8.9 500 2.2 500 2.2 1200 5.3 800 3.6
⁄ Framing
System
16 ga. 1500 6.7 500 2.2 500 2.2 1000 4.4 600 2.7
13 16"
Load diagrams indicate up to three design loads, one for 12 gage sections (P1000), one for 14 gage sections (P1100),
and one for 16 gage sections (P2000).
81
Return to #12 TOC Return to Fittings TOC
Unistrut Finish - Perma-Gold™ (ZD)
Perma-Gold™ (ZD):
The high quality Perma-Gold finish is a zinc dichromate finish applied over an
electro-galvanized zinc plating and is totally compatible with the aesthetics and
performance of yellow dichromate finishes used on other brands of metal framing.
The gold colored zinc dichromate is applied over the electro-galvanized surface to
produce a chemically-bonded, nonporous surface barrier. This provides protection
from moisture and air to extend the life of the zinc and to provide an excellent
surface for painting if desired. The Perma-Gold finish also provides a low electrical
resistance when the system needs to be grounded. To eliminate exposed
surfaces , the channels and fittings are plated after all fabrication. The zinc coating
provides sacrificial protection on exposed edges when field cutting is necessary or
scratches occur during construction and handling.