Professional Documents
Culture Documents
Equipment/Tag Number Process Cooling Water / P-59201A, P-59201B, P-59201C, P-59201D, P-59201E
25873-100-V1A-MPVW-00037
Labriola_Nicholas
003
1-AUG-17
Transmittal 035
P-59201A,P-59201B,P-59201C,P-59201C,P-59201E
Customer: Bechtel Project Franklin
P.O. #: 25873-100-POA-MPVW-00001
ECCN EAR99
S.O. #: 315450
MESC No. :
6 LIQUID CHARACTERISTICS
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
Note : Max
9 VAPOR PRESSURE : barg 0.095 0.037 0.01 & min PUMPS OPERATE: in PARALLEL
only to the
property
12 VISCOSITY : CP 0.84 listed EROSION DUE TO :
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
22 NPSHA : m 13.30
31 ELEVATION (MSL) : 217 m BAROMETER : 739 mmHg INSTRUMENT AIR : MAX bar g MIN bar g
35 Min
38 VOLTAGE 13200
39 PHASE 3
40 HERTZ 60
41 PERFORMANCE DRIVER
42 PROPOSAL CURVE NO. E60367WMPF RPM 505 DRIVER TYPE Electric Motor
44 IMPELLER DIA.: Rated 983.47 MAX. 1087.31 MIN. 978.58 mm POWER TRANSMISSION Direct Drive
46 RATED CURVE BEP FLOW (at rated impeller dia) 16384 m³/h MANUFACTURER ABB
47 MIN FLOW : THERMAL 8406 m³/h STABLE 8404 m³/h DRIVER DETAILS
53 CL PUMP TO U/S BASEPLATE 1.02 m LUBE (if different from pump as specified page 3)
56 SUCTION SPECIFIC SPEED LIMIT m3/h, rpm, m 12,800 THRUST RENK VTZCU
57 SUCTION SPECIFIC SPEED m3/h, rpm, m 12,738 STARTING METHOD Closed-Valve (Unloaded) Start
58 MAX. ALLBLE SOUND PRESS. LEVEL REQD 85 (dBA) SEE DRIVER DATASHEET GM1-7108-U59200-ZV-F28-00001
ECCN EAR99
MESC No. :
2 API PUMP TYPE: VS3 [Based on ISO definitions] CASING MOUNTING: VERTICAL
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
17 Drain Valve Supplied By N /A First Critical Speed Wet (Multi stage pumps only)
20 VENTS MANIFOLDED
21 THREADED CONS FOR PIPELINE SERVICE (6.4.3.2) NO COUPLINGs & GUARDS: (7.2)
26 SERVICE FACTOR
TM
41 LINE SHAFT BEARINGS: dures 250 MOUNTING :
48 REVIEW / APPROVE BB PUMP THRUST BEARING SIZE : PROVIDE SPACER PLATE UNDER ALL EQUIPMENT FEET
53 Location of Pressurized Lube Oil System mounted on baseplate : Pump thrust bearing shall be located in motor. Pump will only
56
ECCN EAR99
MESC No. :
2 SEE ATTACHED API-670 DATA SHEET BUFFER/BARRIER SYSTEM MOUNTED ON PUMP BASEPLATE
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
14 COOLING REQ'D NO
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
28 NUMBER PER THRUST BEARING INACTIVE SIDE MANIFOLD PIPING FOR PURCHASER CONNECTION (7.5.1.6)
32 For Vibration Probes and RTD information, refer to TAG ALL ORIFICES (7.5.2.4) YES
33 Motor Data Sheet (document number 25873-100-V1A-MPVW-00039) SOCKET WELD CONN ON SEAL GLAND (7.5.2.8) N / A
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
ECCN EAR99
MESC No. :
4 SPECIFICATION NO. Industrial Marine Type CURVE & DATA APPROVAL PRIOR TO SHIPMENT. YES
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
7 SURFACE PREPARATION
8 PRIMER
10 Remainder of pump: Amerlock 400 CASTING REPAIR WELD PROCEDURE APPR REQD
12 SURFACE PREPARATION
13 PRIMER:
15
16
17 SHIPMENT: (8.4.1)
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
20 YES
23 SHIPPING & STORAGE CONTAINER (9.2.8.3) ADDNL SUBSURFACE EXAMINATION (6.12.1.5) (8.2.1.3)
24 N2 PURGE (9.2.8.4) N / A
25
27 COMPONENTS TO BE TESTED
28
32 315450 31065 30759 NA 1603 63427 BASEPLATE flatness demonstration Not Required
40 OPERATION TO TRIP SPEED NO TEST NPSHA LIMITED TO 110% SITE NPSHA (8.3.3.6) NO
41 MAX DIA. IMPELLERS AND/OR NO OF STAGES NO NPSH test (only if required by DEP 8.3.4.3)
42 CONNECTION DESIGN APPROVAL (BB pumps only) N/A NPSH TESTING TO HI 1.6 OR ISO 9906 (8.3.4.3.3)
45 OUTLINE OF PROC FOR OPTIONAL TESTS (10.2.5) YES RETEST REQUIRED AFTER FINAL Hd Adj Witnessed
52 VFD STEADY STATE DAMPED RESPONSE ANALYSIS (6.9.2.3) MECHANICAL RUN TEST until oil temp. stable Not Required
56 IGNITION HAZARD ASSMT TO EN 13463-1 (7.2.13.e) BRG HSG RESONANCE TEST (8.3.4.7) Not Required
59 INCLUDE PLOTTED VIBRATION SPECTRA (6.9.3.3) YES REMOVE/INSPECT HYDRODYNAMIC BRGS Not Required
63 VENDOR SUBMIT TEST PROCEDURES (8.3.1.1) YES LOCATION OF AUXILIARY EQUIPMENT TEST
67
ECCN EAR99
MESC No. :
2 REMARKS
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
20 SPACING 1.91 m
22 NUMBER 1 LENGTH NA m
27
37 SUMP ARRANGEMENT
38 SUMP DIMENSIONS :
1 2 3
41 C.L. OF DISCHARGE 3 m
l3
45 2.032 m
l5
l2
l1
l6
48 SUMP DIAMETER d NA m
49
51
52 d
53
54
55
56
MESC No. :
7 THESE REFERENCES MUST BE LISTED BY THE PURCHASER. (DEFAULT TO TABLE 11 IF NO PURCHASER PREFERENCE IS STATED)
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
10 WELDER/OPERATOR QUALIFICATION
16
17 MATERIAL INSPECTION
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
21 ALTERNATIVE MATERIAL INSPECTIONS AND ACCEPTANCE CRITERIA (SEE TABLE 15, 8.2.2.5)
23 RADIOGRAPHY
24 ULTRASONIC INSPECTION
28
29 REMARKS :
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
ECCN EAR99
MESC No. :
NOTES
Electronic documents, once printed, are uncontrolled and may become outdated. Refer to the Enterprise Content Management System (ECMS) for the current revision.
1 Note
Rev
3
1. Pump shall be sized for rated conditions. All other conditions (values) provided for pump mechanical design purpose.
6
Note 2. Deleted
9
3. Refer to Basic Engineering Design Data (BEDD) 25873-001-3BD-M04F-00001 for utilities data.
10
11
12
4. NPSH Margin: Indicate margin between NPSHa and NPSHr at 100% rated flow here: 4.0 meters (minimum of two meters)
13
NPSHa at 120% rated flow is 13.3 meters. NPSHr at 120% rated flow is 11.2 meters.
Confidential © 2014, 2016 Shell Chemical Appalachia LLC. All Rights Reserved.
14
Indicate margin between NPSHa and NPSHr at 120% rated flow here: 2.1 meters (minimum of 0.6 meter)
14
15
5. Pump vendor to provide recommendations on winterization requirements based on ambient conditions. Refer to Basic Engineering
16
Design Data (BEDD) 25873-001-3BD-M04F-00001.
17
18
6. Motor torque shall be rated for start up against an closed discharge valve.
19
20
7. Cooling Water Quality Data specified in the Basic Engineering Design Data (BEDD) 25873-001-3BD-M04F-00001.
21
22
8. Provide pump shaft sealing with a Garlock Style 8093 DSA (Dry-Running Self-Adjusting Pump Packing) or equivalent approved by the Buyer.
23
24
9. See Appendix P for the Cooling Tower Forebay Sketch. Refer to latest forebay drawing from Bechtel.
25
26
10. NPSH test results based on historic model pump testing are acceptable in lieu of new NPSH testing.
27
28
11. Performance test to be performed with job motor and vibration levels to be confirmed during pump performance test.
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
25873-100-POA-MPVW-
PO NO.: GP #: End User: Shell Chemical Appalachia LLC
00001
REV – 0 COMMENTS
Please clarify this additional cooling water
information.
Please place in this box the pressure
Curve
pump (~7.5 bar looking at the pump curve
provided).
surfaces.
4. Page 8 of 8: “Refer to seal vendor document” pump sectional assembly drawing. CP Confirmed. Disregard comment.
25873-100-POA-MPVW-
PO NO.: GP #:
End
User:
Shell
Chemical
Appalachia
LLC
00001
Page 8 of 8: “11. Design natural frequency modeling to vibration levels during performance testing.
model test.”
REVIEWED BY APPROVED BY
This sheet is for communication purposes and will be removed prior to final submittal.