Professional Documents
Culture Documents
Series R®
Helical-rotary Chiller
RLC-PRC026-E4
Introduction
The Trane model RTAD Heat The RTAD with Heat Recovery
Recovery air-cooled helical-rotary option offers high reliability coupled
compressor chiller: with a competitive physical
footprint and acoustical
A solution providing users performance due to its advanced
design, low speed/direct drive
energy savings by compressor and proven Series R®
recovering heat from the performance.
HVAC installation to use The advantages of the model RTAD
elsewhere in the building. with Heat Recovery option are:
• A single equipment control
• A wide range of capacity
Like the standard model RTAD, the • A wide range of applications
Partial Heat Recovery (PHR) and
The Series R® Model RTAD with
Total Heat Recovery (THR) versions
Heat Recovery option helical-rotary
of RTAD utilize the proven design of
screw chiller is designed for
the Trane helical-rotary
applications where a limited or a
compressors. For further
significant amount of heat can be
information about RTAD, the
recovered from the HVAC
product catalogue RLC-PRC015-E4 is
installation to heat or preheat the
available on request from your local
sanitary hot water or in process
Trane representative.
applications with simultaneous
cooling and heating needs.
2 RLC-PRC026-E4
Contents
Introduction 2
Application Considerations 4
Selection Procedure 5
General Data 6
Performance Data -
Partial Heat Recovery 10
Performance Data -
Total Heat Recovery 25
Electrical Data 42
Mechanical Specifications 46
RLC-PRC026-E4 3
Application Considerations
Figure 1 - Performance
Recovery Recovery
CC
CC HC CC HC
CC = Cooling capacity
HC = Heating capacity
4 RLC-PRC026-E4
Selection Procedure
Trane provides assistance in Selection Procedure SI units 6. The final selection in Heating
running extensive load simulations mode is:
To select a Trane air-cooled RTAD
taking into account the specificity of • QTY (1) RTAD 100 PHR
chiller, the following information is
your building, which will determine required: • Cooling Capacity = 332.6 kW
whether it can benefit from the 1. Design load in kW of • Entering/Leaving Chilled Water
savings generated from the refrigeration Temperature = 12/7°C
implementation of a RTAD Heat 2. Design load in kW of heating • Ambient 35°C
Recovery chiller. The following • Heat Capacity = 84.6kW
For Partial Heat Recovery units
parameters must be known to select • Entering/Leaving Temperature
approximately 20% of cooling
the type of option and to calculate Heat Recovery condenser =
capacity can be recovered (latent 40/50°C
the financial viability of this choice:
heat). • Chilled Water Flow Rate = 15.6 l/s
• Cooling load profile: daily typical
For Total Heat Recovery units • Evaporator Water Pressure Drop
cooling load demand for each
month of the year approximately 80% of cooling = 46.3 kPa
capacity can be recovered (latent • Compressor Power Input =
• Heating load profile: daily typical
heating load demand for each heat). 108.8 kW
month of the year 3. Design chilled water temperature • Unit COP = 2.8 kW/kW
drop
Energy costs: electricity to run the
4. Design leaving chilled water • QTY (1) RTAD 100 THR
chiller and an alternative energy
temperature
(gas or fuel) that can be used for • Cooling Capacity = 312.4 kW
5. Design ambient temperature
heating • Entering/Leaving Chilled Water
evaporator flow rates can be
Temperature = 12/7°C
A more favorable payback will be determined by using the
following formula: • Ambient 35°C
obtained when cooling and heating
• Heat Capacity = 251.6 kW
demand are simultaneous and l/s = kW (Capacity) x 0.239 /
• Entering/Leaving Temperature
when the number of running hours Temperature Drop (Degrees C)
Heat Recovery condenser =
of the HVAC system is high. To determine the evaporator 40/50°C
However, in the case of high pressure drop we use the flow rate • Chilled Water Flow Rate = 15.4 l/s
heating load, the amount of energy (l/s) and the evaporator water • Evaporator Water Pressure Drop
that can be recovered from the pressure drop Figure 2. = 44.8 kPa
chiller can justify the installation of • Compressor Power Input =
a hot water storage volume to For applications where the altitude
111.2 kW
balance time offset or load offset is significantly greater than sea
• Unit COP = 2.79 kW/kW
between cooling and heating level or the temperature drop is
demand. different than 6°C, the performance
adjustment factors from Table 113 Contact the local Trane sales
The chiller capacity tables cover the should be applied at this point. engineer for a proper selection at
most frequently encountered
For selection of chilled brine units, the given operating conditions.
leaving liquid temperatures. The
tables reflect a 5°C temperature contact your local Trane sales
engineer. Selection Procedure English units
drop through the evaporator. For
other temperature drops, apply the 1 ton = 3.5168 kW
appropriate Performance Data Evaporator flow rate in GPM = 24 x
Adjustment Factors. tons / delta T (F)
Delta T (F) = delta T (°C) x 1.8
1 GPM = 0.06309 l/s
1 ft WG = 3 kPa
EER = COP / 0.29
RLC-PRC026-E4 5
General Data
6 RLC-PRC026-E4
General Data
RLC-PRC026-E4 7
General Data
8 RLC-PRC026-E4
General Data
Table 4 - General Data RTAD Heat Recovery High Efficiency Low Noise
Unit Size 085 100 115 125 145 150
Number of Compressors 2 2 2 2 2 2
Nominal Size (1) (Tons) 40/40 50/50 60/60 70/70 85/70 85/85
Evaporator
Evaporator Model EG140 EG170 EG200 EG200 EG250 EG250
Water Storage (l) 269 223 204 204 415 415
Minimum Flow (l/s) 6 7.3 8.8 8.8 11.6 11.6
Maximum Flow l/s) 20.8 24.8 30.7 30.7 38.0 38.0
Water Connection Type Victaulic
Water Connection Diameter (inch-mm) 6" - 168.3 6" - 168.3 6" - 168.3 6" - 168.3 6" - 168.3 6" - 168.3
Heat Recovery Heat-Exchanger
Type Brazed Plates
Water Connection Type Victaulic
PHR
Connection diameter (inch - mm) 2" - 60.3 2" - 60.3 2" - 60.3 2" - 60.3 2" - 60.3 2" - 60.3
Water Storage capacity (l) 8 8 9 9 11 11
THR
Connection diameter (inch - mm) 2" - 60.3 2" - 60.3 2" - 60.3 2" - 60.3 3" O.D. - 76.1 3" O.D. - 76.1
Water Storage capacity (l) 10 10 14 14 16 16
Condenser
Number of Coils 2 2 2 2 2 2
Fin series (Fins/ft) 192 192 192 192 192 192
Number of Rows 3/3 3/3 3/3 3/3 3/3 3/3
Condenser Fans
Quantity (1) 3/3 4/4 4/4 5/5 6/5 6/6
Diameter (mm) 762 762 762 762 762 762
Total Air Flow (m3/s) 21.0 24.1 27.2 30.1 34.7 36.2
Nominal Speed (rpm) 750 750 750 750 750 750
Motor kW (kW) 1.23 1.23 1.23 1.23 1.23 1.23
Min Starting/Oper Ambient (2)
PHR (°C) 0 0 0 0 0 0
THR (°C) -18 -18 -18 -18 -18 -18
General Unit
Refrigerant HFC 134a HFC 134a HFC 134a HFC 134a HFC 134a HFC 134a
No. Of independent Refrigerant Circuits 2 2 2 2 2 2
% Min. Load (3) 17 17 17 17 17 17
Weight. Capacities & Dimensions
PHR
Refrigerant Charge (1) (kg) 35/37 38/39 45/48 45/48 63/65 63/65
Oil Charge (1) (l) 6/6 7/7 10/10 10/10 11/11 11/11
Operating Weight (4) (kg) 3411 3541 4084 4179 5574 5629
Shipping Weight (4) (kg) 2655 2784 3325 3420 4812 4867
THR
Refrigerant Charge (1) (kg) 63 / 60 65 / 62 86 / 84 86 / 84 97 / 95 97 / 95
Oil Charge (1) (l) 5/4 5/4 8/7 8/7 8/7 8/7
Operating Weight (4) (kg) 3594 3724 4338 4433 5831 5886
Shipping Weight (4) (kg) 3308 3484 4113 4208 5387 5442
Dimensions
Length (mm) 4426 4426 5351 5351 6370 6370
Width (mm) 2260 2260 2260 2260 2260 2260
Height (mm) 2095 2095 2115 2115 2215 2215
RLC-PRC026-E4 9
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
10 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 11
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
12 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 13
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
14 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 15
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
16 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 17
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
18 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 19
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
20 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 21
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
22 RLC-PRC026-E4
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
RLC-PRC026-E4 23
Performance Data -
Partial Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity, HC = Heating capacity, HX = Heat exchanger 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms
24 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 25
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
26 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 27
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
28 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 29
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
30 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 31
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
32 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 33
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
34 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 35
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
36 RLC-PRC026-E4
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
RLC-PRC026-E4 37
Performance Data -
Total Heat Recovery
Notes :
1. Ratings based on sea level altitude and evaporator fouling factor of 0.044 m² K/kW 4. PI (kW) = Power Input (Compressor + Fans + Control Power)
2. Consult Trane representative for performance at temperatures outside of the 5. COP = Coefficient of performance (CC/PI).
ranges shown 6. Interpolation between points is permissible. Extrapolation is not permitted.
3. CC = Cooling capacity 7. Shaded area reflects Adaptive ControlTM Microprocessor control algorithms.
38 RLC-PRC026-E4
Performance Data
1 = 085 STD
2 = 100 STD, 085 HE
3 = 115 STD, 100 HE
4 = 125 STD, 145 STD, 150 STD, 115 HE, 125 HE
5 = 160 STD, 180 STD, 145 HE, 150 HE
1 = 085-100
2 = 115-125
3 = 145-150
4 = 165-180
RLC-PRC026-E4 39
Performance Data
1 = 085-100
2 = 115-125
3 = 145-150
4 = 165-180
1 = 085-100-115-125
2 = 145-150-165-180
40 RLC-PRC026-E4
Performance Data
Altitude
Chilled
Water Sea Level 600 m 1200 m 1800 m
Temp. drop
4.4 1.000 1.249 1.000 0.996 1.245 1.004 0.991 1.240 1.007 0.987 1.234 1.014
5.6 1.000 1.000 1.000 0.997 0.996 1.004 0.993 0.992 1.007 0.988 0.988 1.015
0.0176 m² K/kW 6.7 1.001 0.835 1.001 0.997 0.832 1.004 0.993 0.828 1.009 0.988 0.824 1.015
7.8 1.003 0.716 1.001 0.999 0.714 1.004 0.994 0.711 1.009 0.990 0.708 1.015
8.9 1.004 0.628 1.001 1.000 0.626 1.005 0.997 0.623 1.009 0.991 0.620 1.016
4.4 0.988 1.235 0.996 0.984 1.230 1.000 0.980 1.225 1.004 0.975 1.220 1.010
5.6 0.988 0.989 0.998 0.986 0.985 1.000 0.981 0.981 1.004 0.977 0.976 1.011
0.044 m² K/kW 6.7 0.990 0.825 0.998 0.987 0.822 1.000 0.983 0.819 1.005 0.978 0.815 1.011
7.8 0.991 0.708 0.998 0.988 0.706 1.001 0.984 0.703 1.005 0.980 0.700 1.011
8.9 0.993 0.621 0.999 0.990 0.619 1.001 0.986 0.617 1.006 0.981 0.614 1.012
Temperature
1 = Propylene Glycol
2 = Ethylene Glycol
RLC-PRC026-E4 41
Electrical Data
Standard
085 1 242 255 0.90 6 x 125 0.217
100 1 282 306 0.88 6 x 160 0.217
115 1 323 359 0.89 6 x 200 0.217
125 1 387 425 0.90 6 x 250 0.217
145 1 437 471 0.90 6 x 250 0.217
150 1 477 502 0.89 6 x 250 0.217
165 1 527 570 0.89 315 + 250 0.217
180 1 576 608 0.89 6 x 315 0.217
High Efficiency
085 1 242 255 0.90 6 x 125 0.217
100 1 291 315 0.88 6 x 160 0.217
115 1 332 368 0.89 6 x 200 0.217
125 1 405 443 0.90 6 x 250 0.217
145 1 446 480 0.90 6 x 250 0.217
150 1 486 511 0.89 6 x 250 0.217
High Ambient
085 1 242 255 0.90 6 x 160 0.217
100 1 291 315 0.88 6 x 200 0.217
115 1 332 368 0.89 6 x 250 0.217
125 1 405 443 0.90 6 x 250 0.217
145 1 446 480 0.90 6 x 250 0.217
150 1 486 511 0.89 6 x 315 0.217
165 1 527 570 0.89 400 + 315 0.217
180 1 576 608 0.89 6 x 400 0.217
Standard Low Noise
085 1 230 243 0.90 6 x 125 0.217
100 1 270 294 0.88 6 x 160 0.217
115 1 311 347 0.89 6 x 200 0.217
125 1 375 413 0.90 6 x 250 0.217
145 1 419 453 0.90 6 x 250 0.217
150 1 457 482 0.89 6 x 250 0.217
165 1 505 548 0.89 315 + 250 0.217
180 1 552 584 0.89 6 x 315 0.217
High Efficiency Low Noise
085 1 230 243 0.90 6 x 125 0.217
100 1 275 299 0.88 6 x 160 0.217
115 1 316 352 0.89 6 x 200 0.217
125 1 385 423 0.90 6 x 250 0.217
145 1 424 458 0.90 6 x 250 0.217
150 1 462 487 0.89 6 x 250 0.217
Standard Low Noise with Night Noise Set Back
085 1 226 238 0.90 6 x 125 0.217
100 1 270 295 0.88 6 x 160 0.217
115 1 312 348 0.89 6 x 200 0.217
125 1 376 414 0.90 6 x 250 0.217
145 1 417 451 0.90 6 x 250 0.217
150 1 453 478 0.89 6 x 250 0.217
165 1 503 546 0.89 315 + 250 0.217
180 1 548 580 0.89 6 x 315 0.217
42 RLC-PRC026-E4
Electrical Data
RLC-PRC026-E4 43
Electrical Data
Standard
085 2 80 80 106 106 144 144 6 2.05 4.5 3 x 50 1600 4
100 2 95 95 125 125 180 180 6 2.05 4.5 3 x 50 1600 4
115 2 111 111 146 146 217 217 6 2.05 4.5 3 x 50 1600 4
125 2 135 135 178 178 259 259 6 2.05 4.5 3 x 50 1600 4
145 2 162 135 214 178 291 259 9 2.05 4.5 3 x 63 1600 4
150 2 162 162 214 214 291 291 10 2.05 4.5 3 x 63 1600 4
165 2 196 162 259 214 354 291 11 2.05 4.5 3 x 63 1600 4
180 2 196 196 259 259 354 354 12 2.05 4.5 3 x 63 1600 4
High Efficiency
085 2 80 80 106 106 144 144 6 2.05 4.5 3 x 50 1600 4
100 2 95 95 125 125 180 180 8 2.05 4.5 3 x 50 1600 4
115 2 111 111 146 146 217 217 8 2.05 4.5 3 x 50 1600 4
125 2 135 135 178 178 259 259 10 2.05 4.5 3 x 50 1600 4
145 2 162 135 214 178 291 259 11 2.05 4.5 3 x 63 1600 4
150 2 162 162 214 214 291 291 12 2.05 4.5 3 x 63 1600 4
Standard Low Noise
085 2 80 80 106 106 144 144 6 1.3 2.5 3 x 50 1600 4
100 2 95 95 125 125 180 180 6 1.3 2.5 3 x 50 1600 4
115 2 111 111 146 146 217 217 6 1.3 2.5 3 x 50 1600 4
125 2 135 135 178 178 259 259 6 1.3 2.5 3 x 50 1600 4
145 2 162 135 214 178 291 259 9 1.3 2.5 3 x 63 1600 4
150 2 162 162 214 214 291 291 10 1.3 2.5 3 x 63 1600 4
165 2 196 162 259 214 354 291 11 1.3 2.5 3 x 63 1600 4
180 2 196 196 259 259 354 354 12 1.3 2.5 3 x 63 1600 4
High Efficiency Low Noise
085 2 80 80 106 106 144 144 6 1.3 2.5 3 x 50 1600 4
100 2 95 95 125 125 180 180 8 1.3 2.5 3 x 50 1600 4
115 2 111 111 146 146 217 217 8 1.3 2.5 3 x 50 1600 4
125 2 135 135 178 178 259 259 10 1.3 2.5 3 x 50 1600 4
145 2 162 135 214 178 291 259 11 1.3 2.5 3 x 63 1600 4
150 2 162 162 214 214 291 291 12 1.3 2.5 3 x 63 1600 4
Standard Low Noise with Night Noise Set Back
085 2 80 80 106 106 144 144 4 1.05 2.6 3 x 50 1600 4
100 2 95 95 125 125 180 180 6 1.05 2.6 3 x 50 1600 4
115 2 111 111 146 146 217 217 6 1.05 2.6 3 x 50 1600 4
125 2 135 135 178 178 259 259 6 1.05 2.6 3 x 50 1600 4
145 2 162 135 214 178 291 259 8 1.05 2.6 3 x 63 1600 4
150 2 162 162 214 214 291 291 8 1.05 2.6 3 x 63 1600 4
165 2 196 162 259 214 354 291 10 1.05 2.6 3 x 63 1600 4
180 2 196 196 259 259 354 354 10 1.05 2.6 3 x 63 1600 4
Notes:
1. Maximum Compressors FLA + all fans FLA + control Amps
2. Starting Amps of the circuit with the largest compressor circuit including fans plus RLA of the second circuit including fans + control Amps
3. Maximum FLA per compressor.
4. Compressors starting Amps, Star delta start.
5. Compressor Power Factor
44 RLC-PRC026-E4
Electrical Data
RLC-PRC026-E4 45
Mechanical Specifications
46 RLC-PRC026-E4
Mechanical Specifications
Unit Controls The unit control module, utilizing Specificity of Total Heat
Adaptive Control™ microprocessor,
All unit controls are housed in a automatically takes action to avoid
Recovery units
weather-tight enclosure with hinged unit shutdown due to abnormal An additional control module is
doors to allow for customer operating conditions associated present on Heat Recovery units. Its
connection of power wiring and with low refrigerant temperature, role is to control the fans to
remote interlocks. All controls, high condensing temperature and maintain the saturated condensing
including sensors, are factory motor current overload. Should the temperature based on the hot water
mounted and tested prior to abnormal operating condition setpoint and also a 3-way valve that
shipment. All cataloged units continue until a protective limit is allows to partially bypass the
comply with EN 60204 and are EMC violated, the unit will be shut down. condenser when inlet water
compatible. Unit protective functions include temperature is low, thus ensuring
Microcomputer controls provide all loss of chilled water flow, the correct operation of the unit.
control functions including start-up evaporator freezing, loss of Note: the use of a 3-way valve can
and shut down, leaving chilled refrigerant, low refrigerant pressure, be avoided by using a variable
water temperature control, high refrigerant pressure, reverse speed pump. The additional control
compressor and electronic rotation, compressor starting and module can provide a 2-10V signal
expansion valve modulation, fan running over current, phase loss, to control it. This solution allows
sequencing, anti-recycle logic, phase imbalance, phase reversal, better control of the outlet water
automatic lead/lag compressor and loss of oil flow. temperature and limits power
starting and load limiting. A menu driven digital display consumption of the pump.
indicates over 60 operating data
points including chilled water Starters
setpoint, current limit setpoint,
leaving chilled water temperature, Starters are housed in a
evaporator and condenser weathertight enclosure with
refrigerant pressures and removable cover plate to allow for
temperatures. Over 60 diagnostic customer connection of power
checks are made and displayed wiring. Wye Delta closed transition
when a problem is detected. The starters are standard on all RTAD
digital display can be read and units.
advanced on the unit without
opening any control panel doors.
Standard power connections
include main three phase power.
RLC-PRC026-E4 47
Literature Order Number RLC-PRC026-E4
Date 1205
New
Literature Stocking Location Europe
Trane has a policy of continuous product and product data improvement and reserves the right to
change design and specifications without notice.
www.trane.com
For more information, contact your local American Standard Europe BVBA
sales office or e-mail us at comfort@trane.com Registered Office: 1789 Chaussée de Wavre, 1160 Brussels - Belgium