Professional Documents
Culture Documents
DragonWave Harmony Enhance MC Configuration and Upgrade Guide
DragonWave Harmony Enhance MC Configuration and Upgrade Guide
Access your link using CLI (Telnet using Putty), and type below command to check Bank A and B Banks
versions:
If you found old OMNI below 1.2.0 revision then upgrade the OMNI File by doing the below( as if you
didn’t upgrade, even with alignment you will not able to ping other side and wireless link will not
establish).
1-Donwload the FTP Software called small ftp, extract it, and put on C directory.
Below is a download link from Yandex storage for FTP Software and OMNI File Upgrade 1.2.0
https://yadi.sk/d/nj-fXoA1InMIpw?w=1
Go to settings and then choose Advance and choose/check option called Use Local IP address and then
Click OK.
Then choose Setting Users, choose add user, put login admin, put password admin, and on Directories
on same box choose add and on Physical Path Box put typically this:
C:\
Then Click OK.
And After this download the OMNI File 1.2.0 and Put it on C Directory direct without any folders.
Then Open Telnet the link and then follow the below instructions carefully:-
Then Enter IP Address of the local laptop (Check your LAN Adapter to figure it out).
Firmware commit
Reset system
Wait for your MW to restart and then check both Banks if OMNI Version is 1.2.0
+Ensure to upgrade the TCF File to latest version 3.02.00 by following below command:
-Power up the MW using Direct DC Power Cable ( PoE is not applicable and can’t be used for this mode),
you will use DC Power Rectifier typically to ODU Direct ( AC Source to Rectifier to ODU) and Use Port 4
on ODU for Both In Band MGMT and For Data.
-Default IP MGMT is untagged/without VLAN, and default range will be 192.168.10.100 (MW) and for
laptop use 192.168.10.X (X= is any IP except 100).
-In Browser preferably to use chrome, open a new tab for 192.168.10.100.
User:admin
Pass:sysManager
(Case sensitive).
-Navigate to Quick configurations tab on left hand side, and click MGMT configurations to configure
MGMT VLAN, and ensure the below is configured as given:-
G0/4 (Must be In Band and VLAN Tagging Check and Enter VLAN ID there).
And then Ensure Carefully to click Submit and then after Save(if you don’t do both steps to save then
configurations will be lost, it must Submit+Save),After doing this you must login with VLAN configured
on your laptop.
Then navigate to IPV4 Configurations, and then configure New IPs, GW, Mask, then do submit and Save
if you don’t do both steps to save then configurations will be lost, it must Submit+Save),
-Navigate to Configurations Tab and then choose System, and then choose General and choose as per
below:
Enter the First VLAN on the Range and type on VLAN ID Field , then choose Bulk , and then put the last
VLAN on the VLAN End Filed, make to tag on Port G0/4 (Data and MGMT Port) and G0/8 which is radio,
and after that make sure to submit and save to avoid losing it.
Simply without enabling Bulk options, just you will need to enter the desired VLAN on the VLAN ID Filed
and then choose Interface G0/4 and G0/8 and choose submit and save to avoid losing configurations.
NOTE: If you want to confirm that specific VLAN or even the range of VLANs has been added successfully
after your save, then you would need on the same page to put VLAN Range (Between VLAN Start to
VLAN end) or if it is one VLAN then type on both VLAN Start and VLAN end and click refresh to check the
output , it supposed to show up on tagged interfaces which you committed.
-Home Tab and choose table to see link signal and status and power.