Professional Documents
Culture Documents
Description
Technical Properties:
Strongcoat Epoxy F is a solvent free, non-toxic epoxy
Colour: Various
floor coa ng with outstanding mechanical and chemical
proper es. Specific gravity: 1.6 ± 0.1
The substrate must be clean, dry, even, dense and free Surface Preparation
from oil, grease, dust and other contaminants. A clean
surface will ensure maximum adhesion between the Unsound layers and contaminated concrete surfaces
substrate and the coa ng. must be prepared using mechanical surface removing
equipment. Acid etching can be used only in well
Concrete floors must have a minimum compressive ven lated areas. Areas deeply contaminated by oil or
strength of 25 N/mm² and a maximum concrete rela ve grease, such areas should be treated by hot compressed
humidity of 80% (max. moisture content of 4%), rela ve air.
humidity can be measured using a hygrometer. Concrete
rela ve humidity should be less than 80% for concrete 28
days old or more.
Strongcoat Epoxy F
Priming
Occassional Spillage.
Strongcoat Epoxy F is designed to be applied over well Chemical Resistance after full cure (7 days
prepared substrates directly without a primer. However, @ 25oC), ASTM D1308 (Spot - test @ 1 hr)
for highly porous substrates, Strongcoat Primer or Organic Acids
Strongcoat Primer S is recommended.
Oleic Acid sat. RS
Mixing Citric Acid 25% R
Vinegar 10% RS
To ensure proper mixing, a mechanically powered mixer
Inorganic Bases
or drill fi ed with a suitable paddle should be used. S r
the content of each component separately to disperse Sodium Hydroxide 50% R
any se lement. Add the en re content of the hardener Ammonia Solu on 10% R
to the base and mix for 3 minutes and un l a uniform Potassium Hydroxide 50% R
colour and consistency are achieved.
Aquous Solu ons
Coating Sodium Chloride sat R
Tap Water R
Use brush or lambs wool roller, or airless spray machine
Chlorinated Water R
to apply the mixed Strongcoat Epoxy F onto the prepared
surfaces. Dead Sea Water R
Solvents
Apply 2 coats of Strongcoat Epoxy F at approximately
0.24 - 0.32 kg/m² per coat. White Spirit R
Xylene R
The first coat should be applied to obtain a con nuous
Toluene R
uniform coa ng. The second coat should be applied
within the over coa ng me to achieve the maximum Acetone R
adhesion between the two coats. Oils & Fuels
All tools should be cleaned immediately using DCP Solvent. A wide range of construc on chemical products are
Hardened material must be cleaned mechanically. manufactured by DCP which include:
Cautions
Fire
Note:
05-0120-C-2021
tĞĞŶĚĞĂǀŽƵƌƚŽĞŶƐƵƌĞƚŚĂƚĂŶLJŝŶĨŽƌŵĂƟŽŶ͕ĂĚǀŝĐĞŽƌƌĞĐŽŵŵĞŶĚĂƟŽŶǁĞŵĂLJŐŝǀĞŝŶ
ƉƌŽĚƵĐƚ ůŝƚĞƌĂƚƵƌĞ ŝƐ ĂĐĐƵƌĂƚĞ ĂŶĚ ĐŽƌƌĞĐƚ͘ ,ŽǁĞǀĞƌ͕ ďĞĐĂƵƐĞ ǁĞ ŚĂǀĞ ŶŽ ĐŽŶƚƌŽů ŽǀĞƌ
ǁŚĞƌĞĂŶĚŚŽǁƉƌŽĚƵĐƚƐĂƌĞĂƉƉůŝĞĚ͕ǁĞĐĂŶŶŽƚĂĐĐĞƉƚĂŶLJůŝĂďŝůŝƚLJĂƌŝƐŝŶŐĨƌŽŵƚŚĞƵƐĞŽĨ
ƚŚĞƉƌŽĚƵĐƚƐ͘