Professional Documents
Culture Documents
Quantel Optimis II Service Manual 31 40
Quantel Optimis II Service Manual 31 40
Inhibition
Inhibition reference
J1 connector J2 connector
(14 pins) (4 pins)
J3 J4
J5
Rev. 05/2005 P - 31
SERVICE MANUAL
S7
S5
S4
S3
S6
S2
S1
P - 32 Rev. 05/2005
CHAPTER 4
INSTALL
INSTALLATION
ALL ATION
SERVICE MANUAL
4 - INSTALLATION
a) Place the chinrest and screw it on the table with the two long six-point
socket screws.
b) Insert a metal shaft in the hole at the side of cross-slide table.
Position two pieces of gears at both ends of the metal shaft and fix it with
six-point socket screws, placing a groove between each gear and groove.
S T OP
S T OP
DANGER
CAUTI O N : FEDERAL USA L AW RESTRI CTS THI S DEVI CE TO SAL E BY O R O N THE
LASER RADI ATI O N
O RDER O F A PHYSI CI AN O R AN O PTO M ETRI ST L I CENCED BY THE L AW O F THE Avoi d eye or ski n exposure t o
STATE I N W HI CH HE PRACTI SES TO USE O R O RDER THE USE O F THI S DEVI CE di rect or scat t ered radi at i on
DANG ER : EXPLO SI O N HAZARD. DO NO T USE I N PRESENCE O F
FLAM M ABLE ANESTETI CS O R O XI G EN. RI CH ATM O SPHERE Nd : YAG 1064 nm 30mJ M ax( 3 p u l ses 4
CAUTI O N : ELECTRI C SHO CK HAZARD. DO NO T O PEN. REFER Di ode 637 nm 1 mW
SERVI CI NG TO Q UALI FI ED SERVI CE PERSO NNEL.
CLASS I V LASER PRO DUCT
P - 34 Rev. 05/2005
SERVICE MANUAL
4 - INSTALLATION
e) Place the both gear covers sliding it under the rail guides of the cross slide
table.
STOP
GROUND
g) Close the rear panel with the large screws passing the cables in the holes
on the rear panel.
Large screws to keep in place rear panel
! IP 20
Rev. 05/2005 P - 35
SERVICE MANUAL
4 - INSTALLATION
i) Switch On the master switch.
Check the panic switch is not activated.
Turn the key to ON, the following screens will be displayed :
Running Selftest
Please Wait
Running Selftest
-----
Running Selftest
- - - - - - - - - - - - OK
0.5mJ 1 Pulse
Count 0
P - 36 Rev. 05/2005
CHAPTER 5
SERVICE MODE
SERVICE MANUAL
5 - SERVICE MODE
Sub-D connector to
connect a PC computer
(linkage RS232)
You can check if the measured energy is in the safety windows (+20%, -
20% and -50%).
Number of pulses
Energy selectionned by Energy value read by
the energy knob the energy meter board,
!displayed in real time)
1.6mJ 1 E1.6mJ
Count 0
Counter value
P - 38 Rev. 05/2005
SERVICE MANUAL
5 - SERVICE MODE
Energy > 3.0mJ When you turn ON the key, the selected energy must be
inferior to 5.0 mJ if you want the laser start (safety).
- Adjust energy at a lower value.
The remote circuit is open or is not properly closed (door or other safety device).
- Close the remote circuit (door or other safety device : Yag 532nm delivery
system in 532nm position).
Check the remote control connection.
Rev. 05/2005 P - 39
SERVICE MANUAL
5 - SERVICE MODE
PROCEDURE :
1 - Remove the jumper connector of the CPU board.
CAUTION : if you forget to select 0.5mJ with the energy knob, the laser will stay in
service mode : - the measured energy will display on the screen,
- the energy safeties will not activated.
P - 40 Rev. 05/2005