Professional Documents
Culture Documents
Procedures of installation
Fuji
Menu
1- CONNECTION OF MOTOR CABLES TO CONTROLLER
2- INVERTER START-UP
4- INVERTER PARAMETERS
5- FIRST START PROCEDURE AFTER INSTALLATION
START- UP MOVILIFT
WARNING
It is important to set inverter without ropes
on motor
2- INVERTER START-UP
WARNING:
We need angle acquisition:
- Set parameter L3=1 and move elevator in inspection for a few seconds, until
Run Contactors will be disabled form inverter.
- If the first start the inverter turn ON shows error Ere reverse the motor
direction (reverse the wires V with W) and try again angle acquisition L03=1.
4-INVERTER PARAMETERS
E12= Acceleration
E13= Deceleration
C07/C07= Creep speed (low speed - Hz)
OTHER
1,6 1,8 1,8 1,9 1,9 2,0 2,0 2,1 2,1 2,2 2,2 2,3 2,3 2,4
1,5 1,7 1,7 1,8 1,8 1,9 1,9 2 2 2,1 2,1 2,2 2,2 2,3
1,4 1,6 1,6 1,7 1,7 1,8 1,8 1,9 1,9 2 2 2,1 2,1 2,2
1,2 1,4 1,4 1,5 1,5 1,6 1,6 1,7 1,7 1,8 1,8 1,9 1,9 2
1,1 1,3 1,3 1,4 1,4 1,5 1,5 1,6 1,6 1,7 1,7 1,8 1,8 1,9
1 1,2 1,2 1,3 1,3 1,4 1,4 1,5 1,5 1,6 1,6 1,7 1,7 1,8
0,9 1,1 1,1 1,2 1,2 1,3 1,3 1,4 1,4 1,5 1,5 1,6 1,6 1,7
0,8 1 1 1,1 1,1 1,2 1,2 1,3 1,3 1,4 1,4 1,5 1,5 1,6
0,7 0,9 0,9 1 1 1,1 1,1 1,2 1,2 1,3 1,3 1,4 1,4 1,5
0,6 0,8 0,8 0,9 0,9 1 1 1,1 1,1 1,2 1,2 1,3 1,3 1,4
F08
1,3 1,4 1,5 1,6 1,7 1,8 1,9 2 2,1 2,2 2,3 2,4 2,5
slowing Parameter
Example: With speed to 0.7 m / s and a deceleration (parameter F08) to 1.8 sec the slowing space
is 1.1 meters.
START- UP MOVILIFT
It 'important to connect
the ground of the
encoder
fig.3
Connection Example
Heidenhain
ECN1313/ECN413
fig.4
START- UP MOVILIFT
Connections:
Thermistor TMS/TMS=
grey/brown TH
fig.2
WARNING!
After installation please remove all short
circuit jumpers and Temporary Inspection
Cable (on Safety Circuit, GND/RS/RD).
1- Move cabin on Ground floor. Display will show 1011
(sensors switch indication).
2- EXC and ALT leds have been ON and also CS (with closed doors)
(otherwise please check Safety Circuits on electrical drawings).
3- If display doesn’t show UNI0 but another message, please check “immediate information” that
is actual state of board.
(more info on MV900 user manual)