Professional Documents
Culture Documents
SEWERAGE BOARD
Subject: SOR for the Year 2019-20.
Preamble:
- Gujarat Water Supply & Sewerage Board is preparing the SOR for
works of Water Supply & Drainage Projects, this SOR is followed by
GWIL and WASMO also.
- SOR for Electro-Mechanical items for the Year 2012-13 was approved
in 240th Board Meeting held on 07-03- 2012.
- For the year 2013- 14, 2014-15, 2015-16, 2016-17, 2017-18 and
2018-19 same rates of SOR of year 2012 13 are considered and
approved in 271st Board Meeting held on 28-02-2019.
- A committee was constituted for preparation of SOR vide office order
No. 603 dated 21-03 2016 and SOR preparation committee was
formed by letter No. 412 dated 17-02- 2016.
- Consultancy Services for formation of Electro-Mechanical SOR was
awarded to reputed consultants M/s Tata Consulting Engineers Ltd.
Periodically fourteen meetings of SOR committee in the presence of
the representative of M/s TCE were held.
- There after Group meetings of GWSSB senior officers & TCEL team
were held on 16-03-2019, 13-05-2019, 01-06 2019, 13-06 2019 &
15-07-2019 for final presentation to SOR scrutiny committee.
- This SOR 2019-20 for electro-Mechanical items has been approved in
the BOD No.272 of GWSSB held on dated.20/07/2019.
Important Notes:-
5) In Section A,B,C,E & F, WPI Old Series and New Series are
compared and effect of the same is incorporated.
S.O.R. derived on basis of following Prevailing Rates
Sr No Particulars Unit Rate In Rs.
1 Cement Beg 260.00
4 Brick No 4.20
3 Copper Wire
104.70 107.70
4 Basic Metal & Alloys
104.60 109.50
Stainless Steel &
5
Alloys 93.90 92.80
6 Aluminium
108.60 112.00
7 Wire Rod
105.30 110.70
8 Fuel & Power
106.70 98.00
9 Electricity (Industry)
101.30 105.40
"D" Section D ELECTRICAL SECTION (As per Electrical SOR of R&B Department)
1 Wiring
1.1 Point wiring in Copper (TISSINO) 39
1.2 Point wiring in Copper (Modular) 40
1.3 Conduits & Pipes 45
1.4 Mains & Wires 47
1.5 Concealed Boxes & Laminated Sheets 50
1.6 Wiring Accessories 50
1.7 LADDERS 52
2 Lamps & Fittings
2.1 LED Lamp & Tubes 53
2.2 LED Light fixture 53
2.3 Industrial Lighting 54
2.4 Landscape Lighting 54
2.5 Flourocent tubes 54
2.6 Street Lighting & Solar Lighting 54
3 Switchgears & Distribution Boards
3.1 Busbar chambers 54
3.2 Panel mounting busbars 55
3.3 Earth Leakage circuit breaker 55
3.4 Danger Notice Boards 57
3.5 Earthing 57
3.6 Metallic Enclosure 58
4 Substation Equipment & Maintenance
4.1 Substation Equipment & Maintenance 60
4.2 Substation Equipment 60
4.4 Substation Maintenance 61
5 Substation Equipment & Maintenance
5.1 Repairing of Mono Bloc Motors 64
4.2 Repairing of open well Horizontal Mono Pumpsets 64
4.4 Repairing of submersible pumpsets 65
"E" Section E ELECTRO - MECHANICAL SECTION
1 3ph Bore-well Submersible Pumps 67
2 Control Panel Board 68
3 PVC insulated flat / round submersible copper cables 69
4A Supply of monobloc pump 3 phase
Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410 69
4B Monoblock pump 3 phase
Casing: CI-FG260, Impeller : SS-CF8M & Shaft : SS:410 69
5 Monoset sub. pump 3 phase
Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410 70
6 Single phase sub pump motor set
Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410 70
7A Labour Charge for fishing out Sub pump set in tubewell 71
7B Labour Charge for fishing out struck up Sub pump set from bore 71
8 Vaccum Pumpset 72
9 Drain Pumpset 72
10 Portable Diesel Driven Self Priming Horizontal Pump (Dewatering set) 72
11 HSCF Pumps 72
12 End Suction Back Pullout Pump 72
13 V.T Pumps Water Lubricated 73
14 Expansion Bellows 73
15 Sewage Nonclog,End Suction type Horizontal centrifugal Pump 77
16 Sewage Nonclog,End Suction type Vertical centrifugal Pump 77
17 Polder type submersible Pump 77
18 Submersible sewage Non-clog Vertical Pump 78
19 11 KV Double / Four Pole Structure Assembly 78
20 Transformer 79
21 Microprocessor Based LV Variable Frequency Drive 83
22 Microprocessor Based LV Soft Starter 83
23 1.1 kV Grade Cable- Aluminium / Copper Conductor 84
24 11 kV (Earthed / Unearthed) Grade Cable- Aluminium Conductor 87
25 6.6 kV (Earthed/ Unearthed) Grade Cable- Aluminium Conductor 87
26 3.3 kV (Earthed/ Unearthed) Grade Cable- Aluminium Conductor 88
27 Cable Terminals (Lugs) 88
28 Cable Glands 91
29 Cable Terminations / Jointing Kits for 1.1kV grade PVC/ XLPE Cable 92
30 Cable Termina ons / Join ng Kits for 3.3 kV (E/UE) / 6.6 kV (E) XLPE Cable 93
31 Cable Termina ons / Join ng Kits for 6.6 kV (UE) / 11 kV (E) grade XLPE Cable 93
32 Cable Terminations / Jointing Kits for 11 kV (UE) grade XLPE Cable 94
33 415V LV Induction Motor 94
34 LT Power Capacitor 104
35 Cable Trays & Accessories 104
36 Rate per KW for comprehensive work of S.I.T.C 106
37 Single Girder crane (H.O.T & E.O.T. Type) 107
38 Double Girder Crane (H.O.T & E.O.T. Type) 108
39 Chain Pulley Block 108
40 LV APFC Panel 108
41 LV MCC Panel with DOL / Star Delta / ATS / Micro processorbased so starter 109
42 HV VCB Switchgear Panel 112
43 Solar System 114
44 Submerged centrifugal pumpsets 115
45 LV Power Control Centre (PCC) 115
46 HFSR (Harmonic Free Series Reactor) soft starter 124
47 Flux Compensated Magnetic Amplifier (FCMA) Soft Starter 126
48 11kV Ring Main Unit (RMU) 128
49 Servo Controlled Automatic Voltage Stabilizer 129
"F" Section F INSTRUMENTATION SECTION
1 Full Bore Electromagnetic Flow Meter- Inbuilt Battery Power operated 131
2 Full Bore Electromagnetic Flow Meter- Regular Power operated 131
3 Insertion Type Ultrasonic Flow Meter 133
4 Clamp On Ultrasonic Flow Meter- Fixed Type 133
5 Clamp On Ultrasonic Flow Meter- Portable Type 134
6 Acoustic Doppler Type Flow Meter- Regular Power Operated 134
7 Water Meters (Multijet/ Woltman Type) 134
8 Water Meters (Woltman Type) 136
9 Bulk Water Meters (Ultrasonic)/ Full Bore Inline Ultrasonic Flow Meter 137
10 Pressure & Vacuum Gauges with Accessories 138
11 Pressure Transmitter 139
12 Float & Board Type Level Indicator 139
13 Float/ Displacer Type Level Switch 140
14 Ultrasonic Level Transmitter 140
"G" Section G TECHNICAL SUPPORT SECTION 141-163
"H" Section H DRAWINGS 164-166
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
300 mm
Drilling of bore hole by Mini DR 416.15
Zone -I
rig including lowering of pipe
assembly, Gravel packing clay 300 mm
1.3 Mtr. 594.79
packing and development of bore Zone -II
hole by washing. (For installation
of Hand pump/Power pump) 300 mm
594.79
Zone -III
Page 1 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 2 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Drilling of 165 mm dia DTH For Zone-III Rajkot and Zone IV Junagadh
Page 3 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Item No. 3
Page 4 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 5 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 6 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 7 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 8 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 9 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Item No. 4
Item No. 5
Page 10 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 11 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 12 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 13 of 166
SOR Mech 2019-20
SECTION - "A"
Rate approved for the year
2019-20
Sr. No Description of Item Size Unit
Work to be carried out by
private agency
Page 14 of 166
SOR Mech 2019-20
SECTION - "A"
Annexure - A
Statement showing the details of Approved rate for the Drillng by DR Rig. For the year 2019-2020
Supply of Cement
400mm reaming
450mm reaming
Supply of Gravel
550mm reaming
600mm reaming
Cement sealing
Bottom sealing
Schedule No
Sticky Clay
Group
mtr
mtr
PSI
PSI
PSI
District Talukas
Unit Mtr Mtr Mtr Mtr Mtr Cmt Cmt M.Ton Job Job Mtr. Job. LS. LS. LS. Mtr.
1 A Gandhinagar Dehgam up to 300 mtr 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
Palanpur, Vedgam,
3 A Banaskanth Dhanera, Dantiwada up to 628 193 291 386 531 701 1894 5882 12388 6217 128 23915 20725 25508 32351 92
300 mtr
Alluviun Area Complete up
4 A Kheda 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
6 A Ahmedabad Dascrol up to 300 mtr 622 190 289 384 527 701 1894 5882 12388 6217 132 24592 20725 25508 32351 92
Dasada,Lakhatar taluka up
7 A Surendranagar 671 206 311 413 568 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Mandvi, Naliya, Mundra up
8 A Kutch 713 220 330 440 602 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Alluviun Area Complete up
9 B Surat 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Alluviun Area Complete up
10 B Bharuch 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Alluviun Area Complete up
11 B Navsari 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Page 15 of 166
SOR Mech 2019-20
SECTION - "A"
Alluviun Area Complete up
12 B Valsad 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Alluviun Area Complete up
13 B Baroda 863 264 397 534 886 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
Bayad, Talod, Dhansura up
14 B Sabarkantha 863 264 397 534 886 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
to 300 mtr
15 B Panchmahal Kalol, Halol up to 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
17 B Amreli Chalala upto 300 mtr 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
19 B Rajkot Maliya upto 300 mtr 863 264 397 534 886 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
20 B Junagadh Vanthali upto 300 mtr. 768 234 354 475.2 789.6 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
21 C Sabarkantha Himatnagar up to 300 mtr 1223 0 588 751 1033 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
Halvad,Dhangadhra,Muli,Wa
22 C Surendranagar dhavan,Chotila,Limadi,Sayal 1223 0 588 751 1033 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
a taluka up to 300 mtr
25 D Sabarkantha Prantij. up to 300 mtr 539 167 250 330 458 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
28 D Patan Vagdod up to 300 mtr 509 154 235 310 431 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92
Page 16 of 166
SOR Mech 2019-20
SECTION - "A"
Gandhinagar, Kalol up to
29 D Gandhinagar 509 154 235 310 431 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92
300 mtr
30 D Mehsana Visnagar up to 300 mtr 522 157 241 318 442 701 1894 5882 12388 6217 133 24888 20725 25508 32351 92
Mehsana,Kadi,Becharaji,Unj
32 E Mehsana ha,Gojarya,Jotana taluka 504 154 234 308 428 701 1894 5882 12388 6217 131 24331 20725 25508 32351 92
up to 300 mtr
Patan,Chanasma,Saraswati,
33 E Patan Siddhapur taluka up to 300 512 156 236 312 434 701 1894 5882 12388 6217 131 24331 20725 25508 32351 92
mtr
34 E Gandhinagar Mansa up to 300 mtr 505 154 233 308 428 701 1894 5882 12388 6217 130 24122 20725 25508 32351 92
Mehsana,Kadi,Becharaji,Unj
39 E Mehsana ha,Gojarya,Jotana taluka 559 172 256 342 475 701 1894 5882 12388 6217 0 26051 0 0 32351 103
Above 300 mtr
Patan,Chanasma,Saraswati,
40 E Patan Siddhapur taluka Above 569 173 263 348 484 701 1894 5882 12388 6217 0 26051 0 0 32351 103
300 mtr
Sami,Harij,Radhanpur,Santa
42 F Patan lpur,Sankheshwar Above 721 222 330 443 613 701 1894 5882 12388 6217 0 26051 0 0 32351 103
300 mtr
Page 17 of 166
SOR Mech 2019-20
SECTION - "A"
Annexure-B1
Approved Drilling of 165mm dia DTH SOR Rate 2019-20 For Zone-1
Approved
Sr. No.
Group
Page 18 of 166
SOR Mech 2019-20
SECTION - "A"
Annexure-B2
Item No.2.2 for Zone-2
Approved Rate for Drilling of 165mm dia DTH for 2019-20
Rate approved
Sr.No District Taluka Unit for the year
2019-20
Page 19 of 166
SOR Mech 2019-20
SECTION - "A"
Annexure-B3
Item No.3.1 For Zone-2
Approved Rate for Drilling of 200mm dia DTH for 2019-20
Rate approved
Sr.No District Taluka Unit for the year
2019-20
Page 20 of 166
SOR Mech 2019-20
SECTION- B
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
Clamp made from M.S. plate with 3 holes on either side with
1
nuts & bolts of Std. Make and suitable size.
Bore plug having 100 mm height made from M.S. plate with 3
holes at equal distance on circumference for nut-bolts type,
2
locking arrangement with nuts-bolts & lock nuts of std. Make
complete.
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
M.S. Bail plug having length 0.45 mtr from medium class pipe
4-A
as per I.S.S. suitable for
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
6
ii) 125 mm dia. No. 522
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
For Item No. 7: Above rates of Pipes are based on WPI Index(98.20) or HRC in month of (Aug-2017)
A-3
Nylock Nut M10x1.50 No. 1.54
A-4
Handle Axle(Stainless Steel) No. 66.00
A-5
Washer (4 mm thick) for Handle Axle No. 1.15
A-6
Bearing (No.6204-Z) No. 24.67
A-7
Spacer(for pump Head) No. 3.80
A-8
Chain with Coupling No. 61.00
A-9
Bolt for front cover M-12x20 mm long No. 2.03
A-10
Pump Head Assly.Consi.of Item No.(1) to (7) as per Fig.3.1 No. 1634.00
B-1
Pump Bucket No. 4.25
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
B-2
Sealing Ring No. 2.75
B-3 Upper Valve Assly comp. consi.of item as per fig 3.6 A (Part
No. 286.00
no 1 to 4 & 8 to 9)
B-4 Lower Valve Assly comp.consi.of item as per fig 3.6 B (Part
No. 161.00
no 5 to 7 & 10)
(C)
WATER TANK consi.of item as per fig 3.6 B(1 to 6) No. 537.00
(D)
Cylinder With Brass Liner consi.of item (a) & (b) No. 292.00
(E)
REDUCER CAP No. 58.00
G-1
Upper Valve Seating No. 1.40
G-2
Plunger Yoke Body No. 89.00
G-3
Bucket Spacer No. 69.00
G-4
Follower No. 83.90
G-5
Plunger Rod (S & S) No. 72.98
G-6
Upper Valve (Guide) No. 38.00
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
(I) Handle Bar consisting of Item no (1) & (3) as per Fig 4.6 No. 548.00
Special Tool Kit for I. M.-II Handpump consi. Item (1) to (11)
(L) No. 5580.00
as per IS 15500 Part-8 with tool box
(N) Third plate consisting of Item (1) & (2) as per fig 4.5 No. 126.60
O-2 Handle Bar consisting of Item no (1) to (3) as per Fig 4.7 No. 1060.00
For Item No. 9: Rates are taken as per RC Rates, approved in TPC-1 dated 10.05.2018.
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
2) 1.50mm Slot size Mtr. 2101
F) Stainless Steel Screen pipes.
2) 400 MM DIA Recharge pit screen 0.75 Slot size Mtr. 7786
3) 550 MM DIA Recharge pit screen 0.75 Slot size. Mtr. 10449
For Item No. 10: Rates are taken as per RC Rates, approved in TPC-1 dated 10.05.2018.
For Item No. 11: Rates are taken as per RC Rates, approved in TPC-1 dated 31.08.2018.
Above rates of Pipes are based on PVC Resin of RIL, Grade 67ER092
(Rs.90093/MT including GST @ 18%) in month of (March-2018)
Providing dust and vermin proof Mild Steel Cabin having two
compartment one for panel board and other for GEB meter
and fuse unit with required locking arrangement , minimum
degree of protection IP 52 as per IS 2147 fabricated from
CRCA sheer steel minimum thickness for base
frame/channel/gland plates for 3 mm for load bearing
12
members ,1.6 mm for ineternal members including
cutting,bending,drilling,welding, riveting with ineternal
partitions.The sheet steel enclosure shall be powder coated
as per applicable standard with shade as required with finish
thickness of paint film not less than 80 microns.The Cabin
have following dimension.
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
i) DN 32 PN-10 Mtr. 31
14
ii) DN 40 PN-10 Mtr. 48
For Item No. 14: Rates are taken as per RC Rates, approved in TPC-1 dated 10.05.2018.
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
Manufacture, Supply and Delivery of 80 mm Nominal
dia UPVC Column Pipes including PVC Socket
3
5 (Coupler), Density of Pipe 1.38 to 1.43 Gm per Cm Mtr. 314
OD : 87.5 TO 88.2MM, Wall Thickness End : 9.8mm to
11.9mm, Berral : 7.3mm to 9.0mm, Length:3Mtrs.
Approved Rate
Sr. No. Description of Item Unit
for 2019-20
RO System
As Above
C Nos. 265000
CAPACITY : 2000 LPH
18 A) upto 65 MM Kg 72
B) Above 65 MM To 100 MM Kg 73
C) Above 100 MM Kg 74
Supply of 300 mm dia RCC Plain pipes used in drilling of
A) Mtr. 380
RCC Tube wells
19
Supply of 300 mm dia RCC Strainer pipes used in drilling
B) Mtr. 470
of RCC Tube wells
Page 31 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
Page 32 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
Construction of soak pit as modified Unicef
design including excavation of (100 cm x 70 cm
x 70 cm deep) with filling of stones, broken
(d) bricks or gravel and laying 29 numbers bricks Job - 384.00
vertically on edge of soak pit etc. complete.
Page 33 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
i) 32 mm No. - 1.85
Page 34 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
Page 35 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
Page 36 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
Medium Commercial Vehicle- Eicher or
equiv. Having carrier length not less
2000 per
than 6 meter
day there
ii
after 15.00
(a) Up to first 100 K.M. per Day Day
per km
(b) Rate per Extra K.M. for more than 100 Km.
K.M. travelling
Hiring of Non AC Inspection vehicle
(SUV) not older than 3 years (M & M:
Bolero / Scorpio / Xuv; Tata: Sumo /
Safari, Jeep or Equivalent) With Driver
& P.O.L. (The vehicle shall have taxi
10 (A) passing with comprehensive full
insurance, fitness certificate & PUC). Fix 21700
Up to 2000 Kilometres / Month
and extra km thereafter i. e. beyond Km. 7.75/Km
2000 kms.
1 30 1156.40 417.72
Page 37 of 166
SECTION - "C"
Approved Rate for
Sr. No Description of Item Unit
2019-20
2 40 1205.10 457.47
3 50 1332.80 580.72
5 75 1345.50 1007.37
Page 38 of 166
Section- "D"
1. For Point wiring above 10 mtr. of length, additional length will be added at rate of mains.
2. For point wiring in bathroom and W/C and washbasin area in residential quarters reduce overall rate by 50% of point wiring
for light.
1.1 Point wiring in Copper (TISSINO)
Point wiring for Light/ Fan/ Bell/ Primary Point with 2-1.5 sq. mm &
earthwire of 1.5 sq. mm (green) both are of ISI marked 1.1kV grade
FRLS PVC insulated multistrand copper wires, in following type of
pipe to be erected concealed in/ flushed on wall /ceiling, complete
1.1.1 with 6A Tissino type ISI marked flush type switch/ bell push and
accessories erected on Metal/ PVC Box covered with 3 mm thick PC
(Polycarbonet)/ Acrylic sheet with necessary Lamp holder/ ceiling
rose/ H.D.Connector as directed.
with medium class Rigid PVC pipe and accessories Pt 270 60 330 -- 330
(a)
with 16 swg(1.6 mm thick) HGS metal conduit pipe and accessories Pt. 370 70 440 -- 440
(b) painted black
(c) with oval conduit/ PVC casing capping double lock type Pt. 240 40 280 -- 280
(d) partial PVC pipe and drops in oval conduit/ PVC casing capping Pt. 255 50 305 -- 305
(a) with medium class Rigid PVC pipe and accessories Pt. 240 50 290 -- 290
with 16 swg HGS metal conduit pipe and accessories painted black Pt. 340 60 400 -- 400
(b)
(c) with oval conduit/ PVC casing capping double lock type Pt. 210 40 250 -- 250
(d) partial PVC pipe and drops in oval conduit/ PVC casing capping Pt. 225 45 270 -- 270
(a) with medium class Rigid PVC pipe and accessories Pt. 425 40 465 -- 465
with 16 swg HGS metal conduit pipe and accessories painted black Pt. 505 50 555 -- 555
(b)
(c) with oval conduit/ PVC casing capping double lock type Pt. 340 40 380 -- 380
(d) partial PVC pipe and drops in oval conduit/ PVC casing capping Pt. 405 40 445 -- 445
(a) with medium class Rigid PVC pipe and accessories Pt. 520 50 570 -- 570
with 16 swg HGS metal conduit pipe and accessories painted black Pt. 610 60 670 -- 670
(b)
with oval conduit/ PVC casing capping double lock type Pt. 460 50 510 -- 510
(c)
(d) partial PVC pipe and drops in oval conduit/ PVC casing capping Pt. 500 50 550 -- 550
Point wiring for secondary light point with 2-1.5 sq.mm & earthwire of
1.5 sq.mm (green) both are of ISI marked 1.1kV grade FRLS PVC
insulated multistrand copper wires, in following type of pipe to be
erected concealed in/ flushed on wall/ ceiling, complete with earth
continuity and necessary connection with primary light with
1.1.4 accessories erected on Metal/ PVC box covered with 3 mm thick PC
(Polycarbonet)/ Acrylic sheet for open/ concealed wiring with
necessary Lamp holder/ ceiling rose/ H.D.Connector as directed.
Note :- Maximum up to 6 mtrs length, excess will be considered as
Mains for Secondary Point.
(A) with medium class Rigid PVC pipe and accessories Pt. 95 25 120 -- 120
with 16 swg HGS metal conduit pipe and accessories painted black Pt. 150 30 180 -- 180
(B)
with oval conduit/ PVC casing capping double lock type Pt. 75 25 100 -- 100
(C)
(D) partial PVC pipe and drops in oval conduit/ PVC casing capping Pt. 85 25 110 -- 110
Point wiring for Two way controlled Light Point with 2-1.5 sq.mm &
earthwire of 1.5 sq. mm (green) both are of ISI marked 1.1kV grade
FRLS PVC insulated multistrand copper wires, in following type of
pipe to be erected concealed in/ flushed on wall/ ceiling complete
1.1.5 with 6A Tissino type ISI marked accessories with earth continuity
erected on Metal/ PVC box covered with 3 mm thick PC
(Polycarbonet)/ Acrylic sheet with necessary Lamp holder/ ceiling
rose/ H.D.Connector as directed.
(A) with medium class Rigid PVC pipe and accessories Pt. 290 60 350 -- 350
with 16 swg HGS metal conduit pipe and accessories painted black Pt. 405 70 475 -- 475
(B)
(C) with oval conduit/ PVC casing capping double lock type Pt. 270 40 310 -- 310
(D) partial PVC pipe and drops in oval conduit/ PVC casing capping Pt. 285 50 335 -- 335
Point wiring for Light/ Bell with 2-1.5 sq. mm & earthwire of 1.5
sq.mm (Green) both are of ISI marked 1.1kV grade FRLS PVC
insulated multistrand copper wires, in following type of pipe to be
erected concealed in/ on surface on wall/ ceiling complete with 6A
Modular type switch/ bell push & accessories and earth continuity of
1.2.1 following type, erected on PVC/ Metallic box, single mounting base
frame covered with textured/ metallic front plate modules erected on/
in wall/ ceiling as per pipe erected, with necessary Lamp holder/
ceiling rose/ H.D.Connector as directed.
with 16 swg HGS metal conduit pipe and accessories painted black
(b)
Cat. I Pt. 390 80 470 -- 470
partial PVC pipe and drops in oval conduit/ PVC casing capping
(d)
Cat. I Pt. 280 50 330 -- 330
Point wiring for FAN with 2-1.5 sq.mm & earthwire of 1.5 sq.mm
(Green) both are of ISI marked 1.1kV Grade FRLS PVC insulated
multistrand copper wires, in following type of pipe to be erected
concealed in/ flushed on wall/ ceiling complete with 6A Modular type
switch and hume free EME four or more step type electronic fan
1.2.2 regulator with separately mounted and accessories with earth
continuity of following type erected on PVC/ Metallic box, single
mounting base frame covered with textured/ metallic front plate
modules erected on/ in wall/ ceiling as per pipe erected with
necessary ceiling rose/ H.D.Connector as directed.
with 16 swg HGS metal conduit pipe and accessories painted black
(b)
(a) 20 mm Mtr. 15 5 20 -- 20
(b) 25 mm Mtr. 25 5 30 -- 30
(c) 32 mm Mtr. 30 5 35 -- 35
(d) 40 mm Mtr. 35 5 40 -- 40
UPVC TRUNKING SYSTEM
(A) Supplying and laying UPVC cable trunking system comprising
unplasticised polyvinyl chloride rigid material with ignition free &
1.3.6 flame proof confirming BS. All necessary accessories and measuring
of following sizes.
(a) 75 mm x 50 mm trunking Mtr. 260 20 280 -- 280
(b) 100 mm x 50 mm trunking Mtr. 400 30 430 -- 430
(B) UPVC COUPLER
(a) For 75 mm x 50 mm trunking Ea 40 5 45 -- 45
(b) For100 mm x 50 mm trunking Ea 60 5 65 -- 65
(C) UPVC ELBOW
(a) For 75 mm x 50 mm trunking Ea 70 5 75 -- 75
(b) For100 mm x 50 mm trunking Ea 130 5 135 -- 135
(D) UPVC TEE
(a) For 75 mm x 50 mm trunking Ea 90 5 95 -- 95
(b) (2) For100 mm x 50 mm trunking Ea 110 5 115 -- 115
(E) UPVC INTERNAL BEND
(a) For 75 mm x 50 mm trunking Ea 70 5 75 -- 75
(b) For100 mm x 50 mm trunking Ea 90 5 95 -- 95
(F) UPVC EXTERNAL BEND
(a) For 75 mm x 50 mm trunking Ea 70 5 75 -- 75
(b) For100 mm x 50 mm trunking Ea 90 5 95 -- 95
(G) UPVC END CAP
(a) For 75 mm x 50 mm trunking Ea 70 5 75 -- 75
(b) For100 mm x 50 mm trunking Ea 80 5 85 -- 85
(H) SOCKET MOUNTING FRAME
(a) For one Gang Ea 60 5 65 -- 65
(b) For two Gang Ea 75 5 80 -- 80
(I) UPVC TRUNKING DIVIDER
(a) For 50 mm (depth) trunking Ea 30 0 30 -- 30
(f) 300mm x 25mm x 1.6 mm with Three Compartments Mtr 1180 50 1230 -- 1230
(g) 50mm x 38mm x 1.6 mm with One Compartments Mtr 360 20 380 -- 380
(h) 75mm x 38mm x 1.6 mm with one compartments Mtr 440 20 460 -- 460
(i) 100mm x 38mm x 1.6 mm with One Compartments Mtr 520 30 550 -- 550
(j) 150mm x 38mm x 1.6mm with Three Compartments Mtr 730 40 770 -- 770
(k) 225mm x 38mm x 1.6mm with Three Compartments Mtr 1060 40 1100 -- 1100
(l) 250mm x 38mm x 1.6mm with Three Compartments Mtr 1160 40 1200 -- 1200
(m) 300mm x 38mm x 1.06 mm with Three Compartments Mtr 1300 50 1350 -- 1350
(b) 300mm x 200mm x 50mm for 2 Nos Compartments Ea 2530 70 2600 -- 2600
Floor mounted metal S.S. outlet (under floor service) made of high
quality ABS & polyamide materials with trap frame & screw less
1.3.9 ratchet trap lead with screw less knob reinforced with 2.5mm thick
pregalvanised steel plate of following size.
250mm x 250mm x 60/75 mm one trap three compartment (Metal Ea 4500 100 4600 -- 4600
(a)
lead)
(b) 300mm x 300mm x 60/75 mm (Metal lead) Three Compartments Ea 5300 100 5400 -- 5400
Junction Box
PVC/ GI Junction cross over box for metal/ Al. trunking with duct
entry 25mm x 38mm size having epoxy powder coated trap lead with
1.3.10 corrosion & rust free having load bearing capacity of 3.6 tons with
adjustable levelling screw of following size.
(a) 150mm x 150mm x 60/75 mm depth Ea 950 50 1000 -- 1000
(b) 250mm x 250mm x 60/75 mm depth Ea 1380 70 1450 -- 1450
(c) 300mm x 300mm x 60/75 mm depth Ea 2150 100 2250 -- 2250
(d) 350mm x 350mm x 60/75 mm depth Ea 2400 100 2500 -- 2500
(e) 400mm x 400mm x 60/75 mm depth Ea 2850 150 3000 -- 3000
Supplying under floor trunking accessories joint sleeves for 25mm /
1.3.11 38mm pipe with following dimensions.
1-6-6. 5A, 10 way bakelite connector duly erected on existing board Ea. 22 3 25 -- 25
1.6.7 15A, 10 way bakelite connector duly erected on existing board Ea. 40 5 45 -- 45
1.6.8 Providing & erecting ISI marked 3 pin plug top
(a) for 5/6 A., 240V Ea. 18 2 20 -- 20
(b) for 15/16A, 240V Ea. 28 2 30 -- 30
Supplying & erecting approved make call bell indicator with buzzing Ea. 130 20 150 -- 150
1.6.9 sound and red light indicating lamp with red light button to attend the
call suitable for 240V, 50c/s supply to be erected.
1.6.10 Call bell/ buzzer 250 volts, complete erected Ea. 25 5 30 -- 30
Call bell gong type suitable for 230 volts, 50 c/s AC supply complete Ea. 35 5 40 -- 40
1.6.11 erected
Decorative call bell ting-tong box type 250 volts complete erected Ea. 64 6 70 -- 70
1.6.12
Supplying & erecting electronic type cordless call bell erected on Ea. 250 0 250 -- 250
1.6.13 PVC/ Metal board having portable bell push working on DC & bell on
230V AC supply with cells/ battery.
Providing automatic staircase unit and light control switch with Ea. 650 50 700 -- 700
1.6.14 photocell & solid state circuits with loading capacity up to 1000 Watt
Supplying electrical insulation LT tape role with ISI marked having Ea. 15 0 15 -- 15
1.6.15 nominal width 1.8cms nominal length 9.0mtr nominal thickness
0.125mm and having self adhesive PVC
Supply of Fibreglass Step (A Type) Ladder- 6 FT having following Ea. 14100 0 14100 -- 14100
specifications:
It should have nonconductive structural moulded top with slots to
keep tools close at hand, inside spreader braces, aluminium feet with
1.7.2 thick rubber tread, nonconductive full channel fibreglass and two
pairs of gusset support at the bottom step. All gussets are heavy duty
steel.
Capacity: 300 lbs. , Step Size: 3”, Width: 23” Approx. , Spread: 41”
Approx. , Wt.: 11Kg Approx. , Cube : 6.2’
Supply of Fibreglass Step (A Type) Ladder- 8 FT having following Ea. 18400 0 18400 -- 18400
specifications:
It should have nonconductive structural moulded top with slots to
keep tools close at hand, inside spreader braces, aluminium feet with
1.7.3 thick rubber tread, nonconductive full channel fibreglass and two
pairs of gusset support at the bottom step. All gussets are heavy duty
steel.
Capacity: 300 lbs. , Step Size: 3”, Width: 26” Approx. , Spread: 54”
Approx., Wt.: 15 Kg Approx. , Cube: 9.5
Supply of Fibreglass Step (A Type) Ladder- 10 FT having following Ea. 22600 0 22600 -- 22600
specifications:
It should have nonconductive structural moulded top with slots to
keep tools close at hand, inside spreader braces, aluminium feet with
1.7.4 thick rubber tread, nonconductive full channel fibreglass, two pairs of
gusset support at the bottom step. All gussets are heavy duty steel.
Capacity: 300 lbs, Step Size: 3”, Width: 29” Approx., Spread: 66”
Approx. , Wt.: 19 Kg Approx., Cube: 12.54’
Supply of Fibreglass Step Trestle (A Type) Ladder- 6 FT having Ea. 16500 0 16500 -- 16500
following specifications:
It should have heavy gauge steel hinges suitable for industrial
application, inside spreader braces, aluminium feet with thick rubber
tread, nonconductive full channel fiberglass, two pairs of gusset
1.7.5 support at the bottom step. All gussets are heavy duty steel. It should
have steps on both the sides for climbing. Capacity: 300 lbs.
Step Width: 3”, Bottom Width:23” Approx. , Spread :
52”Approx.Wt.:13 Kg, Approx. Cube : 6.53’
Supply of Fibreglass Step Trestle (A Type) Ladder- 8 FT having Ea. 22000 0 22000 -- 22000
following specifications:
It should have heavy gauge steel hinges suitable for industrial
application, inside spreader braces, aluminium feet with thick rubber
1.7.6 tread, nonconductive full channel fibreglass, two pairs of gusset
support at the bottom step. All gussets are heavy duty steel. It should
have steps on both the sides for climbing. Capacity: 300 lbs., Step
Width: 3”, Bottom Width: 26” Approx.
Spread: 67” Approx. , Wt.: 20 Kg Approx. , Cube: 9.51’
Supply of Fibreglass Step Trestle (A Type) Ladder- 10 FT having Ea. 26000 0 26000 -- 26000
following specifications:
It should have heavy gauge steel hinges suitable for industrial
application, inside spreader braces, aluminium feet with thick rubber
tread, nonconductive full channel fibreglass, two pairs of gusset
1.7.7
support at the bottom step. All
gussets are heavy duty steel. It should have steps on both the sides
for climbing.
Capacity: 300 lbs., Step Width: 4”, Bottom Width: 29” Approx.
Spread: 83” Approx. , Wt.: 27 Kg Approx., Cube: 13.44’
Supplying and erecting R&B approved make of LED batten for Ea. 325 0 325 18% 384
2.2.2 multipurpose application made from polycarbonate housing with 2 x
9/ 18/ 21W T8 with all accessories
Supplying and erecting approved R&B make of LED Downlighter
2.2.3 recessed mounted for Indoor application
(a) With 10 watt LED lamp Ea. 866 0 866 18% 1022
(b) With 18/ 20 watt LED lamp Ea. 945 0 945 18% 1115
Supplying and erecting R&B approved make of LED Downlighter
2.2.4 surface mounted for Indoor application
(a) With 10 watt LED lamp Ea. 758 0 758 18% 894
(b) With 18/ 20 watt LED lamp Ea. 1010 0 1010 18% 1192
Supplying and erecting R&B approved make of LED recessed
2.2.5 mounted luminaire with rear reflector suitable for office and laboratory
applications
(a) With 20 watt LED lamp Ea. 1803 0 1803 12% 2019
(b) With 36 watt LED lamp Ea. 2452 0 2452 12% 2746
(c) With 40 watt LED lamp Ea. 3029 0 3029 12% 3392
Supplying and erecting R&B approved make of LED Suraface
2.2.6 mounted luminaire with rear reflector suitable for office and laboratory
applications
(a) With 20 watt LED lamp Ea. 2019 0 2019 12% 2261
(b) With 36 watt LED lamp Ea. 3245 0 3245 12% 3634
(c) With 40 watt LED lamp Ea. 3389 0 3389 12% 3796
Supplying and erecting R&B approved make of LED Weatherproof
2.2.7
tubelight fixture with tube
With 1 x 18 watt LED lamp Ea. 1190 0 1190 12% 1333
With 1 x 36 watt LED lamp Ea. 2452 0 2452 12% 2746
2.5.2 R&B Approved make fluorescent tube (T8) 60 cms. 36 watt Ea. 57 0 57 12% 64
2.5.3 R&B Approved make 9 watt compact fluorescent lamp Ea. 67 0 67 12% 75
2.5.4 R&B Approved make 11 watt compact fluorescent lamp Ea. 73 0 73 12% 82
2.5.5 R&B Approved make 18 watt compact fluorescent lamp Ea. 124 0 124 12% 139
2.6 Street Lighting & Solar Lighting
R&B Approved make street light luminaire with one no suitable for-
2.6.1 LED lamp complete with alluminium PDC housing toughened glass
with cover IP 66 Protection.
(a) With 70 watt LED lamp Ea. 4687 0 4687 12% 5249
(b) With 90 watt LED lamp Ea. 6850 0 6850 12% 7672
(c) With 120 watt LED lamp Ea. 8652 0 8652 12% 9690
Supplying and erecting R&B approved make, standalone solar LED
2.6.2 street light system with tubular pole, polyacryline PV panel solar
tubular battery. Battery box pole and mechanical hardware
(a) With 15 watt LED lamp Ea. 30138 0 30138 12% 33755
(b) With 30 watt LED lamp Ea. 42395 0 42395 12% 47482
(c) With 60 watt LED lamp Ea. 89116 0 89116 12% 99810
(d) With 70 watt LED lamp Ea. 101157 0 101157 12% 113296
Supplying and erecting R&B approved make, standalone solar LED
2.6.3 mini mast system with tubular pole, polyacryline PV panel solar
tubular battery. Battery box pole and mechanical hardware.
(a) with 3 x 33W Flood light, 8M High Pole Ea. 182413 0 182413 12% 204303
(b) with 3 x 45W Flood light, 10M High Pole Ea. 221347 0 221347 12% 247909
3 SWITCHGEARS & DISTRIBUTION BOARDS
3.1 BUSBAR CHAMBERS
(a) 25 A FP
Cat. I Ea. 2040 70 2110 -- 2110
Cat. II Ea. 2260 70 2330 -- 2330
Cat. III Ea. 2930 70 3000 -- 3000
(b) 40 A FP
Cat. I Ea. 2180 70 2250 -- 2250
Cat. II Ea. 2350 70 2420 -- 2420
Cat. III Ea. 3010 70 3080 -- 3080
(c) 63 A FP
Cat. I Ea. 2390 70 2460 -- 2460
Cat. II Ea. 2790 70 2860 -- 2860
Cat. III Ea. 3480 70 3550 -- 3550
(d) 100 A FP (100 mA Sensitivity)
Cat. II Ea. 2860 70 2930 -- 2930
Cat. III Ea. 4970 70 5040 -- 5040
Supplying & erecting R&B approved make RCBO (Electro magnetic
type only) working on residual current device having 6 KA short
circuit breaking capacity and 30 mAmp. Sensitivity & 30 mili sec.
3.3.3 tripping time conforming to IS 12640 test knob facility trip free
mechanism operating for rated leakage at nominal ten volt, complete
erected including all materials lugs screws etc. completed.
(a) 6A / 10A / 16A / 20A / 25A 2 pole single phase Cat. II Ea. 2050 70 2120 -- 2120
(b) 32A / 40A, 2 pole Single Phase Cat. II Ea. 2200 70 2270 -- 2270
(c) 63 A, 2 pole Single Phase Cat. II Ea. 2660 70 2730 -- 2730
(d) 6A to 25 A, 4 Pole Three Phase Cat. II Ea. 2330 70 2400 -- 2400
(e) 32A to 40 A, 4 Pole Three Phase Cat. II Ea. 2460 70 2530 -- 2530
(f) 63A, 4 pole Three Phase Cat. II Ea. 3240 70 3310 -- 3310
Supplying & fixing box for housing ELCB / ELCB + MCB combination
made of 18 SWG sheet steel duly powder coated with gasket, dust &
3.3.4
vermin proof bakelite shield two earthing terminals for following type
of RCCB, ELCB, ELCB + MCB
(a) For 2 pole Ea. 270 50 320 -- 320
3.5.4 Supply & erectionAnnealed bare Copper wire 8 to 16 SWG. Kg. 670 40 710 -- 710
Supply & erection HOT deep Galvanised iron strip wire 8 to 16 SWG. Kg. 70 20 90 -- 90
3.5.5
Pipe type earthing having 150 cms.long and 2.5 cms. dia. galvanised Ea. 350 80 430 -- 430
3.5.6(a) iron pipe with coupling and buch buried in specially prepared earth pit
complete with necessary 8 SWG earth wire.
Pipe type earthing with 40 mm dia 2.5 mtr long 'B' grade G.I. pipe Ea. 810 150 960 -- 960
with necessary coupling buch buried in specially prepared earth pit &
3.5.6(b)
G.I. earth wire of 8 SWG erected & connected as directed (For panel)
For using salt and charcoal / coke as required for pipe type earthing. Ea. 180 20 200 -- 200
3.5.6(c)
Add Extra for excavation in Semi hard rock (Murrum) by dry and wet Ea. 0 130 130 -- 130
3.5.7
blasting and chiselling for pipe type earthing
Add Extra for excavation in Hard rock by dry and wet blasting and Ea. 0 325 325 -- 325
3.5.8 chiselling for pipe type earthing.
Supplying & erecting earth pit of minimum bore dia.150mm size
approved make Earthing Electrode consisting Pipe-in-Pipe
Technology as per IS 3043-1987 made of corrosion free G.I.Pipes
having Outer pipe dia of 50mm having 80-200 Micron galvanising,
3.5.9
Inner pipe dia of 25 mm having 200-250 Micron galvanising,
connection terminal dia of 12mm with constant ohmic value
surrounded by highly conductive compound with high charge
dissipation suitable for following type of applications.
For Electrical Installation up to 440V in normal soil Ea. 6630 520 7150 -- 7150
(a) Length of pipe - 1 Mtr
Back filling compound - 1 Nos Bag of 15 Kg.
For Electrical installation up to 11 KV in normal soil. Ea. 8370 600 8970 -- 8970
(b) Length of Pipe : 2.00 mtrs
Back filling Compound :1 no. Bag of 25 Kg.
For Electrical Installation covering Transformer Neutrals, Lightning Ea. 12550 900 13450 -- 13450
arrester Earthing, A.C.Plant & Sensitive Computer System(like
(c) Automation, SCADA) i.e independent Earthing in normal soil.
Length of Pipe : 3.00 mtrs
Back filling Compound :2 nos Bags of 25 Kg.
Supplying & erecting in earthpit of minimum bore dia. 225mm size
ASH or approved make Safe Earthing Electrode consisting Pipe-
in-Pipe Technology as per IS 3043-1987 made of corrosion free
G.I.Pipes having Outer pipe dia of 80 mm having 80-200 Micron
galvanising, Inner pipe dia of 40 mm having 200-250 Micron
3.5.10
galvanising, connection terminal dia of 14 mm with constant ohmic
value surrounded by highly conductive compound with high charge
dissipation suitable for following type of applications.
(A) With 30 x 30 x 0.35 cms: C.I. earth plate Ea. 1900 800 2700 -- 2700
(B) With 45 x 45 x 0.35 cms. C.I. earth plate Ea. 2200 800 3000 -- 3000
(C) with 60 x 60x 0.315 cms. Copper earth Plate Ea. 8400 800 9200 -- 9200
ADD Extra for excavation in Semi hard rock (Murrum) by dry and wet Ea. 10 250 260 -- 260
3.5.13 blasting and chiselling for funnel type earthing of above
ADD Extra for excavation in Hard rock by dry and wet blasting and Ea. 0 380 380 -- 380
3.5.14 chiselling for funnel type earthing of above .
Cast iron earth plate size 30 X 30 X 0.35 cms. buried in specially Ea. 600 200 800 -- 800
prepared 2.5 Mtr. deep earth pit complete with necessary G.I. strip in
3.5.15 G.I. pipe 2 Mtr. long with coupling and G.I. plug for earthing of switch
gear, conduit run or power plug etc.
Cast iron earth plate size 45 X 45 X 0.35 cms. buried in Ea. 800 200 1000 -- 1000
specially prepared 2.5 Mtr. Deep earth Pit complete with necessary
3.5.16 G.I. strip in G.I. pipe 2 Mtr. long with coupling and G.I. plug for
earthing of switch gear, conduit run or power plug etc.
Maintenance free Chemical Earthing Ea. 5356 0 5356 -- 5356
Supply of UL Listed Maintenance Free Earthing System made of
copper bonded rod of 10 feet (3 mtr approx.)
length, 17.2 mm dia. (Minimum copper bonding shall be 0.25mm,
3.5.12 suitable for 25 kA fault current) along with Rod-to-Conductor
connectors, 95% pure Carbon-Based
Earth enhancement material of 30kg, Pit Cover as required and as
per specification.
Supply of UL complying Maintenance Free Earthing System made of Ea. 2266 0 2266 -- 2266
copper bonded rod of 4 feet (1.2 mtr approx.) length, 17.2 mm dia.
(Minimum copper bonding shall be 0.25mm) along with Rod-to-
3.5.13
Conductor connectors, 95% pure Carbon-Based Earth enhancement
material of 5kg, Pit Cover as required and as per
specification.
3.6 METALLIC ENCLOSURE
Transformer oil having good resistance to high electrical stress, high Ltr. 85 0 85 -- 85
di-electric strength (50kV) low viscosity, low pour point, high flash
4.2.9
point and excellent thermal properties for efficient heat transfer and
cooling as per I.S.335 -1972.
Filtration of transformer oil as per I.S.S. for removal of moisture,
carbon, slurry etc. by means of circulating oil through vacuum pump
4.2.10 from heating elements and filters to with stand the breaking strength
of the oil above 40kV beyond one minute tested in oil testing Kit.
(a) on site Ltr. 0 9 9 -- 9
(b) at factory Ltr. 0 7 7 -- 7
4.3 SUBSTATION MAINTENANCE
Carryout routine maintenance, servicing and testing of HT VCB Job 0 2500 2500 -- 2500
(rating upto 1250 A) including cleaning of Breaker mechanism,
4.3.1 auxiliary male-female contacts, time leg fuse contact coil contacts,
overload and earth fault trip device control wiring contacts, lowering
and lifting mechanism on trolley drawout mechanism etc.
Carry out routine maintenance and servicing and testing of LT ACB Job 0 1950 1950 -- 1950
(rating upto 2000 Amp) by cleaning fix contacts, moving contacts and
4.3.2 arc chutes including servicing and putting the ACB in perfect
working order after setting all relays and ON/ OFF mechanism.
Carry out routine maintenance and servicing of LT cubicle panel Job 0 2500 2500 -- 2500
board having approximately 15 to 22 Nos. of switches cleaning and
servicing the contacts tightning the connections of incoming and
4.3.3 outgoing cables. and checking the operating mechanism for smooth
functioning of switches. and putting them in smooth working order.
Carrying out the testing of earth fault and overload relay on LT side. Job 0 1950 1950 -- 1950
4.3.4 Removing the fault of relay by checking the trip devices, control
wiring and putting the same in working order.
Testing and calibration of protective relays and metering devices Job 0 2200 2200 -- 2200
4.3.5 through primary Injection up to 3000 AMP (3 coils sets)
Routine maintenance of Transformer in operation covering check for Job 0 4300 4300 -- 4300
Insulation Resistance, oil breakdown strength, reconditioning
4.3.6 /replacement of silica gel, cleaning of transformer & topping up of oil
if required. (excluding cost of transformer oil)
4.3.7 Testing of transformer oil for dielectric breakdown strength. Job 0 320 320 -- 320
Measurement of earthing resistance by loop test after isolating & Job 0 1950 1950 -- 1950
4.3.8
cleaning joint.
Dismantling and refitting of transformer including cost of required
4.3.9
new M.S. bolts of following capacity transformer
(a) 250 kVA Ea. 455 1495 1950 -- 1950
(b) 315 kVA Ea. 455 1495 1950 -- 1950
(c) 500 kVA Ea. 375 1725 2100 -- 2100
(d) 750 kVA Ea. 315 2185 2500 -- 2500
(e) 1000 kVA Ea. 425 2875 3300 -- 3300
(f) 1600 kVA Ea. 550 3450 4000 -- 4000
Replacing old and unserviceable gasket of Top cover plate of
4.3.10 Transformer having following capacity.
Replacement of On load Tap changing of 250/ 315/500/750/ Ea. 3470 230 3700 -- 3700
4.3.25 1000kVA Transformer.
Replacing H.T. bushing of 250/ 315/ 500/750/ 1000kVA Transformer Ea. 202 23 225 -- 225
4.3.26 by new one
Replacing H.T Bushing metal parts of 250/ 315/ 500/ 750/ 1000kVA Ea. 281 29 310 -- 310
4.3.27 Transformer by new one.
Replacing H.T Bushing all other parts of 250/ 315/ 500/ 750/ Ea. 151 29 180 -- 180
4.3.28 1000kVA Transformer
Replacing L.T. Bushing all/ other parts of the 250/ 315/ 500/750/ Ea. 565 35 600 -- 600
4.3.31 1000kVA Transformer.
5-1-11. Rewinding of 20 H.P., 3 phase 440V motor as per original winding design by Ea. 5500.00 550.00 6050.00 12.0% 6776.00
using super enamelled copper Wire and putting the same in working condition as
per original.
5-1-12. Replacing burnout unserviceable ball bearing / Roller bearing suitable for Ea.
following motors for mono block pump sets
(A) For 1 H.P. motor/pump Ea. 154.00 44.00 198.00 12.0% 221.76
(B) For 2 H.P. motor/pump Ea. 220.00 44.00 264.00 12.0% 295.68
(C) For 3 H.P. motor/pump Ea. 275.00 44.00 319.00 12.0% 357.28
(D) For 5 H.P. motor/pump Ea. 308.00 66.00 374.00 12.0% 418.88
(E) For 7.5 H.P. motor/pump Ea. 385.00 66.00 451.00 12.0% 505.12
(F) For 10/12.5 H.P. motor/pump Ea. 550.00 66.00 616.00 12.0% 689.92
(G) For 15 H.P. motor/pump Ea. 638.00 110.00 748.00 12.0% 837.76
(H) For 20 H.P. motor/pump Ea. 660.00 110.00 770.00 12.0% 862.40
SECTION 6--2 REPAIRING OF OPEN WELL HORIZONTAL MONO PUMP SETS
5-2-1. Dewatering sump well by hiring pump sets & temporary pipe connections of
following sump capacity
(a) up to 5000 Ltr Job 0.00 220.00 220.00 5.0% 231.00
(b) Above 5000 Ltr to 20000 Ltr Job 0.00 275.00 275.00 5.0% 288.75
(c) Above 20000 Ltr to 1 Lac Ltr Job 0.00 385.00 385.00 5.0% 404.25
(d) Above 1 Lac Ltr Job 0.00 550.00 550.00 5.0% 577.50
5-2-2. Opening the open well sub. mono pump set for fault finding , carry out required
repairs refitting the same with necessary oiling, greasing & overhauling & making
pump set in good working condition. (Excludes cost of repairing. Includes to &
from transportation)
(i) 1.0 HP to 5HP Ea. 0.00 350.00 350.00 5.0% 367.50
(ii) 7.5 to 15HP Ea. 0.00 385.00 385.00 5.0% 404.25
(iii) Above 15HP Ea. 0.00 495.00 495.00 5.0% 519.75
5-2-3. Rewinding single phase 230V motor for open well horizontal mono pump set by
using polycab copper winding wire & putting the same in working order for pump
capacity of
(a) 0.5 HP - 230V Ea. 1012.00 110.00 1122.00 12.0% 1256.64
(b) 1HP - 230 V Ea. 1375.00 110.00 1485.00 12.0% 1663.20
5-2-4. Rewinding 3 phase, 440V motor for open well horizontal mono pump set by
using poly. cap copper winding wire & putting the same in working order for
pump capacity of
(a) 0.5 H.P./ 1 HP / 1.5 HP - 440V Ea. 1210.00 110.00 1320.00 12.0% 1478.40
(b) 2 HP / 3 HP - 440V Ea. 1485.00 110.00 1595.00 12.0% 1786.40
(c)5 HP - 440V Ea. 1870.00 220.00 2090.00 12.0% 2340.80
(d) 7.5 HP - 440V Ea. 2255.00 220.00 2475.00 12.0% 2772.00
(e) 10 HP - 440V Ea. 3135.00 275.00 3410.00 12.0% 3819.20
(f) 12.5 HP - 440V Ea. 3245.00 275.00 3520.00 12.0% 3942.40
(g) 15 HP - 440V Ea. 3465.00 275.00 3740.00 12.0% 4188.80
(h) 20 HP - 440V Ea. 3685.00 330.00 4015.00 12.0% 4496.80
(i) 25 HP - 440V Ea. 4455.00 385.00 4840.00 12.0% 5420.80
(j) 30 HP - 440V Ea. 5200.00 415.00 5615.00 12.0% 6288.80
5-2-5. Replacement of S.S. sleeves for shaft of open well horizontal submersible pump
sets for
(i) 1HP to 5HP Ea. 319.00 55.00 374.00 12.0% 418.88
(ii) 7.5 to 15HP Ea. 578.00 55.00 633.00 12.0% 708.96
(iii) Above 15HP Ea. 957.00 55.00 1012.00 12.0% 1133.44
5-2-6. Replacement of Stainless Steel bushing fitted in end shield for open well
horizontal submersible pump set
(i) 1HP to 5 HP Ea. 506.00 55.00 561.00 12.0% 628.32
(ii) 7.5Hp to 15 HP Ea. 770.00 55.00 825.00 12.0% 924.00
(iii) above 15 HP Ea. 935.00 55.00 990.00 12.0% 1108.80
5-2-7. Replacement of Gun metal /Bronze bushing for open well horizontal
submersible pump set
(i) 1HP to 5 HP Ea. 220.00 55.00 275.00 12.0% 308.00
(ii) 7.5Hp to 15 HP Ea. 330.00 55.00 385.00 12.0% 431.20
(iii) above 15 HP Ea. 385.00 55.00 440.00 12.0% 492.80
5-2-8. Replacing gasket, oil, nuts, bolts & washers for open well horizontal submersible
pump sets.
(i) 1HP to 5 HP Ea. 220.00 55.00 275.00 12.0% 308.00
(ii) 7.5Hp to 15 HP Ea. 330.00 55.00 385.00 12.0% 431.20
(iii) above 15 HP Ea. 385.00 55.00 440.00 12.0% 492.80
5-2-9. Replacement of Bronze / Carbon thrust bearing with fibber plate & bushing
suitable for open well horizontal submersible pump set for
(i) 1HP to 5 HP Ea. 1210.00 55.00 1265.00 12.0% 1416.80
(ii) 7.5Hp to 15 HP Ea. 1573.00 55.00 1628.00 12.0% 1823.36
(iii) above 15 HP Ea. 2057.00 55.00 2112.00 12.0% 2365.44
5-2-10. Replacement of cast iron impeller for openwell horizontal submersible pump
pump sets
(i) 1HP to 5 HP Ea. 275.00 110.00 385.00 12.0% 431.20
(ii) 7.5Hp to 15 HP Ea. 495.00 165.00 660.00 12.0% 739.20
(iii) above 15 HP Ea. 825.00 165.00 990.00 12.0% 1108.80
5-2-11. Replacement of Bronze / Gunmetal impeller for open well horizontal submersible
pump set
(i) 1HP to 5 HP Ea. 825.00 110.00 935.00 12.0% 1047.20
(ii) 7.5Hp to 15 HP Ea. 990.00 165.00 1155.00 12.0% 1293.60
(iii) above 15 HP Ea. 1210.00 165.00 1375.00 12.0% 1540.00
SECTION 6--3 REPAIRING OF SUBMERSIBLE PUMP SETS
5-3-1. Opening the submersible pump set for fault finding , carry out required repairs
refitting the same with necessary oiling, greasing & overhauling & making pump
set in good working condition. (Excludes cost of repairing. Includes to & from
transportation)
5-3-4. Replacement of motor bush, upper/ lower with sleeve with following material
(A) Bronze
(i)150 mm. dia. Ea. 495.00 55.00 550.00 12.0% 616.00
(ii)200 mm. dia Ea. 990.00 55.00 1045.00 12.0% 1170.40
(B)Rubber
(i)150 mm. dia. Ea. 297.00 22.00 319.00 12.0% 357.28
(ii)200 mm. dia Ea. 495.00 22.00 517.00 12.0% 579.04
5-3-5. Replacement of stage casing bowl with nuts and bolts.
(A)C.I.
(i)150 mm. dia. Ea. 330.00 55.00 385.00 12.0% 431.20
(ii)200 mm. dia Ea. 495.00 55.00 550.00 12.0% 616.00
(B)Bronze
(i)150 mm. dia. Ea. 550.00 55.00 605.00 12.0% 677.60
(ii)200 mm. dia Ea. 693.00 55.00 748.00 12.0% 837.76
5-3-6. Replacement of Bronze impeller with neck ring.
(i)150 mm. dia. Ea. 396.00 55.00 451.00 12.0% 505.12
(ii)200 mm. dia Ea. 605.00 55.00 660.00 12.0% 739.20
5-3-7. Replacement of Shaft sleeve stainless steel.
(i)150 mm. dia. Ea. 55.00 11.00 66.00 12.0% 73.92
(ii)200 mm. dia Ea. 138.00 11.00 149.00 12.0% 166.88
5-3-8. Replacement of Bowl bearing/ bush
(A) Rubber
(i)150 mm. dia. Ea. 308.00 55.00 363.00 12.0% 406.56
(ii)200 mm. dia Ea. 605.00 55.00 660.00 12.0% 739.20
(B) Lead
(i)150 mm. dia. Ea. 693.00 55.00 748.00 12.0% 837.76
(ii)200 mm. dia Ea. 1100.00 55.00 1155.00 12.0% 1293.60
5-3-9. Replacement of S.S.Shaft for
(A) 3 stage pump
(i)150 mm. dia. Ea. 286.00 28.00 314.00 12.0% 351.68
(ii)200 mm. dia Ea. 473.00 44.00 517.00 12.0% 579.04
(B) Add per stage
(i)150 mm. dia. Ea. 83.00 11.00 94.00 12.0% 105.28
(ii)200 mm. dia Ea. 121.00 11.00 132.00 12.0% 147.84
5-3-10. Replacement of suction strainer
(i)150 mm. dia. Ea. 94.00 17.00 111.00 12.0% 124.32
(ii)200 mm dia. Ea. 187.00 22.00 209.00 12.0% 234.08
I Electric motor driven Borewell submersible pump set conforming to I.S. 8034 and motor conforms to IS-9283 working at 3 phase
400/440 volt 50 C/S A.C. supply & 2900 R.P.M.
II Cat No. Discharge in Head in mtr Mini Motor
LPM HP
a) 1.0 90 60.0 3.00 No 10,970 12% 12,286
b) 1.1 90 90.0 5.00 No 12,900 12% 14,448
c) 1.2 90 120.0 6.00 No 14,500 12% 16,240
d) 1.3 90 150.0 7.50 No 17,000 12% 19,040
e) 1.4 90 180.0 10.00 No 19,800 12% 22,176
f) 2.0 135 60.0 4.00 No 11,100 12% 12,432
g) 2.1 135 90.0 6.00 No 13,100 12% 14,672
h) 2.2 135 120.0 7.50 No 15,120 12% 16,934
i) 2.3 135 150.0 10.00 No 18,000 12% 20,160
j) 2.4 135 180.0 12.50 No 20,340 12% 22,781
k) 2.5 135 210.0 15.00 No 25,530 12% 28,594
l) 2.6 135 240.0 17.50 No 26,100 12% 29,232
m) 2.7 135 255.0 17.50 No 26,430 12% 29,602
n) 3.0 180 72.0 6.00 No 12,510 12% 14,011
o) 3.1 180 108.0 10.00 No 16,110 12% 18,043
p) 3.2 180 144.0 12.50 No 19,370 12% 21,694
q) 3.3 180 163.0 12.50 No 20,110 12% 22,523
r) 3.4 180 180.0 12.50 No 22,190 12% 24,853
s) 3.5 180 215.0 15.00 No 25,551 12% 28,617
t) 3.6 180 255.0 20.00 No 29,820 12% 33,398
u) 3.7 180 275.0 22.50 No 31,000 12% 34,720
v) 4.0 240 72.0 7.50 No 13,025 12% 14,588
w) 4.1 240 108.0 25.00 No 16,700 12% 18,704
x) 4.2 240 144.0 15.00 No 21,480 12% 24,058
y) 4.3 240 170.0 17.50 No 24,120 12% 27,014
z) 4.4 240 190.0 20.00 No 25,600 12% 28,672
aa) 4.5 240 210.0 20.00 No 31,150 12% 34,888
ab) 4.6 240 230.0 25.00 No 28,000 12% 31,360
ac) 4.7 240 250.0 25.00 No 30,750 12% 34,440
ad) 5.0 320 55.0 7.50 No 14,211 12% 15,916
ae) 5.1 320 92.0 12.50 No 16,600 12% 18,592
af) 5.2 320 130.0 17.50 No 21,750 12% 24,360
ag) 5.3 320 150.0 20.00 No 24,100 12% 26,992
ah) 6.0 400 60.0 10.00 No 16,430 12% 18,402
ai) 6.1 400 90.0 15.00 No 21,130 12% 23,666
aj) 6.2 400 120.0 20.00 No 26,700 12% 29,904
ak) 6.3 400 150.0 22.50 No 31,000 12% 34,720
al) 7.0 510 52.0 12.50 No 20,110 12% 22,523
am) 7.1 510 87.0 20.00 No 27,810 12% 31,147
an) 7.2 510 123.0 25.00 No 32,100 12% 35,952
ao) 7.3 510 141.0 30.00 No 34,600 12% 38,752
ap) 7.4 510 159.0 35.00 No 35,600 12% 39,872
aq) 7.5 510 175.0 40.00 No 38,310 12% 42,907
ar) 8.0 800 72.0 25.00 No 28,900 12% 32,368
as) 8.1 800 108.0 35.00 No 33,760 12% 37,811
at) 8.2 800 144.0 45.00 No 40,500 12% 45,360
au) 8.3 800 162.0 50.00 No 41,850 12% 46,872
av) 8.4 800 180.0 55.00 No 46,160 12% 51,699
aw) 8.5 800 198.0 60.00 No 48,430 12% 54,242
ax) 9.0 1,200 63.0 27.50 No 30,810 12% 34,507
2.2 Auto Transformer Starter suitable for local & remote pump control application consisting of Auto Transformer (vacuum
impregnated, air cooled having three (3) tappings at 50%, 65% and 80%), incomer MCCB / MPCB, overload relay and contactors
as per Type II coordination including digital MFM with RS 485 communication port, analogue type ammeter with selector switch,
run hour meter, required protective relays & control accessories.
a) A. T. S. from 21 to 30 HP No 20,230 18% 23,871
3.1 PVC insulated flat submersible cable as per detailed technical specifications of R/C of GWSSB conforming to IS 694, IEC 60227 /
60228.
a) 2 RMT 25.23 18% 29.77
1 R x 3 C x 1.5 mm
b) 2 RMT 38.73 18% 45.70
1 R x 3 C x 2.5 mm
c) 2 RMT 57.67 18% 68.05
1 R x 3 C x 4.0 mm
d) 1 R x 3 C x 6.0 mm2 RMT 80.14 18% 94.57
4A Monobloc pump 3 phase 400/440 vott, 50 c/s. A.C. Supply & 2800 RPM following IS 9079 at departmental stores with following
MOC : Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410
4B Monoblock pump 3 phase 400/440 vott, 50 c/s. A.C. Supply & 2800 RPM following IS 9079
MOC : Casing: CI-FG260, Impeller : SS-CF8M & Shaft : SS:410
Sr. No Rating Discharge Head
H.P LPM mtr.
5 Monoset sub. pump 3 phase 400/440 vott, 50 c/s. A.C. Supply & 2900 RPM , following IS 14220
MOC : Casing: CI-FG260, Impeller : Bronze & Shaft : SS:410
Sr. No Category Rating H.P. Discharge Headmtr.
LPM
a) SM - 2.1 4 220 22.5 No 9,930 12% 11,122
7(A) Labour Charge for fishing out Sub pump set fallen in the tube well of size 150mm/200mm/250mm dia. Including carting of
required mats, fixtures for fishing to site of work and also including carting charges of the fished out Sub pump set and
accessories to the respective departmental store including loading and unloading.
a) Job Up to 150 Mtr. Job 20,381 5% 21,400
7(B) Labour Charge for fishing out struck up Sub pump set /pipes /cable etc. from 165/200/250 mm bore by applying sp. Tech with sp.
Tools /Fixtures by Agency.
a) Job Up to 150 Mtr. Job 17,762 5% 18,650
9 Supply of Horizontal Mono-Submersible Pump set (Drain pump) as per IS: 14220 / 1994 & its latest amendments of following duty parameters with suitable
submersible motor as per IS: 9283 / 1994 & its latest amendments working on 3 ø, 415 V ± 10%, 50 ± 3% Hz power supply, rated speed 2900 RPM of
following duty capacity. Material of Constructions: Impeller- High tensile brass / LTB II; Casing- CI FG 260; Pump & Motor shaft- SS 304; Bearing Bush- LTB
III
Flow Head
10 Providing and erecting portable diesel driven self priming horizontal mono pump set (Dewatering set) with four wheel trolley, GI medium duty delivery
pipes, specials, suction strainer etc. complete set Material of Constructions: Impeller-Bronze, Casing-C.I., Shaft-Carbon Steel
12-30 LPS 6-12 mtr Head No. 25,720 Incl. 25,720 12% 28,806
11 HSCF Pumps
A Supply, Testing & Commissioning of Horizontal Split casing centrifugal pump motor set of specified duty parameters & guaranteed efficiency of following
MOC with specified capacity, horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%,
rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS.
M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410, Mechanical
Seal (above 30 kW) , Base Frame: MS.
Rating
A Supply, Testing & Commissioning of End Suction Back Pull-out centrifugal pump motor set with base frame of specified duty parameters & guaranteed
efficiency of following MOC with specified capacity horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50
Hz ± 3%, 415 V ± 10%, rated speed 1450 RPM along with fabricated MS base frame, coupling, coupling guard, foundation bolts etc. as per relevant IS.
M.O.C.: Impeller & Wearing Rings: Bronze LTB II IS: 318, Casing: CI FG 260 IS: 210 , Shaft: SS 410, Shaft Sleeve: Bronze LTB II IS: 318 or SS 410,
Mechanical Seal (above 30 kW), Base Frame: MS.
Rating
A Supply, Testing & Commissioning of Vertical Turbine pump motor set of specified duty parameters & guaranteed efficiency of following MOC with specified
capacity horizontal foot mounted TEFC squirrel cage induction motor, working on three phase AC supply with 50 Hz ± 3%, 415 V ± 10%, rated speed 1450
RPM along with column and bowl assembly, discharge head, base channel/RSJ etc. complete as per relevant IS.
M.O.C.: Impeller & Sealing Rings:CF8M, Bowl & Suction Bell: CI FG 260 IS: 210 with 2% Ni , Shaft with coupling: SS 410, Column Pipe: M.S. ERW,
Mechanical Seal (above 30 kW), Base Plate: MS, Line Bearing: Thordon type, Suction Strainer: S.S.
Rating
14 Expansion Bellows
Supply, testing & commissioning of flange ends Expansion Bellow as per EJMA standards of overall length of minimum 300 mm, designed for 15 mm axial
compression and 5 mm axial extension with tie rods etc. of following MOC & pressure ratings.
MOC: Bellows: SA 240 Gr. 304; Internal Sleeve: SA 240 Gr. 304; Weldends: IS 2062 Gr. B; Flanges: IS 2062 Gr. B (Drilling as per IS 1538 /IS 6392 ) & Limit
Rods & Nuts: CS - IS 1367.
A PN - 1.0
B PN - 1.6
C PN - 2.0
D PN - 2.5
Supply of non clog sewage end suction type horizontal centrifugal pump set of required capapcity & head with suitable TEFC squirrel cage
foot mounted induction motor working on three phase 50 Hz ± 3%, 415V ± 10% AC supply, 1500 RPM synchronous speed along with base
frame, coupling with guard, foundation bolts, strainer etc. complete set as per relevant IS & following M.O.C: Casing: 1.5 to 2% Ni. C.I;
Impeller & wearing ring: SS-CF8M, Shaft with sleeve: S.S. & Base frame: C.I., Guide Pipe: SS.
Supply of non clog seweage vertically mounted end suction type vertical centrifugal pump set of required capapcity & head with suitable
TEFC squirrel cage foot mounted induction motor working on three phase 50 Hz ± 3%, 415V ± 10% AC supply, 1500 RPM synchronous
speed including suitable provision of extended shaft of 2 meters length to couple with motor along with base frame, coupling with guard,
foundation bolts, strainer etc. complete set as per relevant IS & following M.O.C: Casing: 1.5 to 2% Ni. C.I; Impeller & wearing ring: SS /
CF8M, Shaft with sleeve: S.S. & Base frame: C. I; Guide Pipe: S. S.
Providing submersible, Non clog type with required capapcity & head as per IS 8034 suitable for water having upto 10000 PPM turbidity
with suitable submersible wet type, water cooled, squirrel cage motor to IS 9283, working on three phase, 50 Hz +/-3%, 415V +/- 10%, AC
supply, 2900 RPM synchroNous speed with 10 mtr copper conductor flat cable from pump to starter panel with cable end terminations (4)
all supports, clamps, pipe fittings alongwith mechanical seal, bearing bush, strainer etc. complete set & following M.O.C: Casing CI, SS
CF8M impeller, Bronze: wearing ring & Bearing bush, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor
body.
Providing sewage submersible, Non clog type suitable for working on Air filled Dry type motor, three phase, 50 Hz +/-3%, 415V +/- 10%, AC
supply, 1500 RPM synchronous speed with 3 core flat copper cable from pump to starter panel with cable end terminations (4) all
supports, clamps, pipe fittings alongwith mechanical seal, bearing bush, strainer etc. complete set & following M.O.C: Casing CI, SS CF8M
impeller, Bronze: wearing ring & Bearing bush, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor body.
11 kV Double Pole Structure Assembly Each 96,120 24,543 120,663 18% 142,383
11 kV Four Pole Structure Assembly Each 116,640 34,542 151,182 18% 178,395
20 Transformer
20.1 SITC of outdoor type, three phase, oil immerged, distribution transformer of required KVA & voltage ratio, copper double wound, vector group -
Dyn11, HV delta connected & LV star connected with neutral brought out connected to provide separate earthing terminals, bushing / cable box on
HV side and cable box on LV side suitable for cables or bus duct as per requirement with standard fittings, conforming to IS: 1180 (Part-1) / 2014 with
its latest amendment including first fill of transformer oil & following accessories.
(a) Oil conservator with filling holes with cap and prismatic oil level gauge.
(b) Silica Gel dehydrating breather charged with silica gel
(c) Oil drain cum sampling valve with plug
(d) Oil filter valve
(e) Lifting Eyes / Hooks / Lugs
(f) Two earthing terminal
(g) Diagram and rating plate
(h) Air release plug
(i) Explosion vent with diaphragm
(j) Thermometer pocket
(k) Four bi-directional plain roller with base channel with hauling holes
(l) Fixed / Separate type radiator banks
(m) Off circuit externally operated tapping switch (For rating < 1000 kVA)
(n) 100 mm stem type oil temperature indicator (For rating < 500 kVA)
(o) Bucholtz relay with shut off valve (For rating ≥ 500 KVA)
(p) 150 mm dial type oil temperature indicator with Alarm / Trip contact (For rating ≥ 500 kVA)
(q) 150 mm dial type winding temperature indicator with Alarm / Tip contact (For rating ≥ 1000 kVA)
(r) Marshalling box (For rating ≥ 500 kVA)
(s) 150 mm dia. magnetic type oil gauge (For rating ≥ 1600 kVA)
(t) Inspection cover & Jacking lugs (For rating ≥ 1600 kVA)
20.1.1 With off circuit tap changer ± 7.5% in steps of 2.5%
a Eff. Level-2 160 0.67/ 1.95/ 4.5 Set 350,997 30,000 380,997 18% 449,576
b Eff. Level-3 0.57/ 1.7/ 4.5 Set 386,097 30,000 416,097 18% 490,994
c Eff. Level-2 200 0.78/ 2.3/ 4.5 Set 412,860 30,000 442,860 18% 522,575
d Eff. Level-3 0.67/ 2.1/ 4.5 Set 454,146 30,000 484,146 18% 571,292
e Eff. Level-2 250 0.98/ 2.93/ 4.5 Set 491,593 30,000 521,593 18% 615,480
f Eff. Level-3 0.92/ 2.7/ 4.5 Set 540,752 30,000 570,752 18% 673,488
g Eff. Level-2 315 1.02/ 3.1/ 4.5 Set 581,574 30,000 611,574 18% 721,658
h Eff. Level-3 0.95/ 2.75/ 4.5 Set 639,732 30,000 669,732 18% 790,283
i Eff. Level-2 400 1.25/ 3.45/ 4.5 Set 659,757 35,000 694,757 18% 819,814
j Eff. Level-3 1.15/ 3.3/ 4.5 Set 725,733 35,000 760,733 18% 897,665
k Eff. Level-2 500 1.51/ 4.3/ 4.5 Set 715,996 35,000 750,996 18% 886,175
l Eff. Level-3 1.43/ 4.1/ 4.5 Set 787,595 35,000 822,595 18% 970,662
m Eff. Level-2 630 1.86/ 5.3/ 4.5 Set 839,720 35,000 874,720 18% 1,032,170
n Eff. Level-3 1.74/ 4.85/ 4.5 Set 923,692 35,000 958,692 18% 1,131,257
o Eff. Level-2 800 2.28/ 6.4/ 5.0 Set 873,523 40,000 913,523 18% 1,077,957
p Eff. Level-3 2.14/ 5.83/ 5.0 Set 960,875 40,000 1,000,875 18% 1,181,033
q Eff. Level-2 1000 2.7/ 7.7/ 5.0 Set 1,003,940 40,000 1,043,940 18% 1,231,850
r Eff. Level-3 2.62/ 7.0/ 5.0 Set 1,104,334 40,000 1,144,334 18% 1,350,314
20.1.2 With on load tap changer ± 10% steps of 1.25% with RTCC & AVR.
b Eff. Level-3 3.3/ 9.2/ 5.0 Set 1,738,457 50,000 1,788,457 18% 2,110,379
c Eff. Level-2 1250 3.3/ 9.20/ 5.0 Set 1,637,960 50,000 1,687,960 18% 1,991,793
d Eff. Level-3 3.2/ 8.44/ 5.0 Set 1,801,756 50,000 1,851,756 18% 2,185,073
e Eff. Level-2 1600 4.2/ 11.8/ 6.25 Set 1,854,261 50,000 1,904,261 18% 2,247,028
f Eff. Level-3 3.97/ 11.3/ Set 2,039,687 50,000 2,089,687 18% 2,465,831
6.25
g Eff. Level-2 2000 5.05/ 15.0/ Set 2,065,220 60,000 2,125,220 18% 2,507,760
6.25
h Eff. Level-3 4.79/ 14.1/ Set 2,271,743 60,000 2,331,743 18% 2,751,456
6.25
i Eff. Level-2 2500 6.15/ 18.5/ Set 2,335,597 60,000 2,395,597 18% 2,826,805
6.25
j Eff. Level-3 5.9/ 17.5/ 6.25 Set 2,569,157 60,000 2,629,157 18% 3,102,405
20.2 SITC of outdoor type, three phase, oil immerged, power transformer of required KVA & voltage ratio, copper double wound, vector group - Dyn11, HV
delta connected & LV star connected with neutral brought out connected to provide separate earthing terminals, bushing / cable box on HV side and
cable box on LV side suitable for cables or bus duct as per requirement with standard fittings, conforming to IS: 2026 - 2011 with its latest
amendment including first fill of transformer oil & following accessories.
(a) Oil conservator with filling holes with cap and prismatic oil level gauge. (b) Silica Gel dehydrating breather charged with silica gel (c) Oil drain cum
sampling valve with plug (d) Oil filter valve (e) Lifting Eyes / Hooks / Lugs (f) Two earthing terminal (g) Diagram and rating plate (h) Air release plug (i)
Explosion vent with diaphragm (j) Thermometer pocket
(k) Four bi-directional plain roller with base channel with hauling holes (l) Fixed / Separate type radiator banks (m) Off circuit externally operated
tapping switch (For rating < 1000 kVA)
(n) 100 mm stem type oil temperature indicator (For rating < 500 kVA) (o) Bucholtz relay with shut off valve (For rating ≥ 500 KVA) (p) 150 mm dial
type oil temperature indicator with Alarm / Trip contact (For rating ≥ 500 kVA) (q) 150 mm dial type winding temperature indicator with Alarm / Tip
contact (For rating ≥ 1000 kVA) (r) Marshalling box (For rating ≥ 500 kVA)
(s) 150 mm dia. magnetic type oil gauge (For rating ≥ 1600 kVA) (t) Inspection cover & Jacking lugs (For rating ≥ 1600 kVA)
20.2.1 With off circuit tap changer ± 7.5% in steps of 2.5%
20.2.2 With on load tap changer ± 10% in steps of 1.25% with RTCC & AVR
20.3 Casting of transformer plinth / foundation including oil soak pit (where required) in situ reinforced cement concrete in M 20 using granite,
quartzite trap metal of size 6 mm to 20 mm for RCC work including providing of 53 grade cement & Fe 415 grade TMT bars, scaffolding,
centering, form work, curing etc. complete.
Supplying, erecting, commissioning of 415 V Fully automatic microprocessor based Variable Frequency drive for pump control application
as per general specification as under:
The VFD unit shall have modular construction, 6 Pulse Bridge rectifier, speed control by means of sensorless vector control (open loop),
high torque at low frequencies, locking at high and low frequency settings, In-built PID control, frequency accuracy of ± 0.1 % (min),
frequency resolution of ± 0.1 Hz (min), protections against; a) overload (motor and drive), b) short circuit, c) ground fault, d) input/ output
phase loss (open circuit), e) stalling, f) input/ output undervoltage (momentary power loss restart), g) input/ output overvoltage, h) over-
frequency, i) Input surge, j) over temperature of heatsink, k) loss of remote speed signal etc. The VFD shall also have user-friendly
programming software & it shall be capable of at least two level parameter setting with password lock for critical parameters,
programming for I/Os, speed search function, copy parameters (upload/download) to other identical unit, tuning to energy saving mode
(maximum efficiency), event/fault recording (last 5 faults in non-volatile memory) & RS485 communication port (MODBUS RTU protocol)
with required software.
22.1 Supplying, erecting & commissioning of 415 V Fully automatic Microprocessor based soft starter with external bypass arrangement for
pump control application as per general specification as under:
Control Method -Torque Control, Input voltage- 415V, 3 Phase, Input frequency -50/ 60 Hz (±5%), Confirmative to standard - IEC 61947-4-
2UL,CSA,CE,
Motor protection - inbuilt Thermal Protection, Starter protection - SC UV, Phase unbalance, Phase failure, EMC Std- IEC 61000-4-2 Level-3
& IEC 61000-4-3-Level-3, Built in communication as per RS 485.
a 30 kW No 33,539 4,545 38,084 18% 44,939
22.2 Supplying, erecting & commissioning of 415 V Fully automatic Microprocessor based soft starter with built in bypass arrangement for
pump control application as per general specification as under:
Control Method -Torque Control, Input voltage- 415V, 3 Phase, Input frequency - 50/ 60 Hz (±5%), Confirmative to standard - IEC 61947-4-
2UL,CSA,CE,
Motor protection - inbuilt Thermal Protection, Starter protection - SC UV, Phase unbalance, Phase failure, EMC Std- IEC 61000-4-2 Level-3
& IEC 61000-4-3-Level-3, Built in communication as per RS 485.
a 30 kW No 27,950 4,545 32,495 18% 38,344
23.1 Supply, laying, testing & commissioning 1.1 kV grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire
armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:
23.2 Supply, laying, testing & commissioning 1.1 kV grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire
armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:
23.3 Supply, laying, testing & commissioning 1.1 kV grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round wire
armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:
23.4 Supply, laying, testing & commissioning 1.1 kV grade, XLPE insulated, stranded Copper conductor, galvanised steel flat strip / round wire armoured,
extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable trays / conduit /
pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1), of following sizes:
23.5 Supply, laying, testing & commissioning of 1.1 kV grade, XLPE insulated, stranded Copper conductor, galvanised steel flat strip / round wire
armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1), of following
sizes:
23.6 Supply, laying, testing & commissioning of 1.1 kV grade, XLPE insulated, stranded Copper conductor, galvanised steel flat strip / round wire
armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-1) & IEC:60502 (Part-1) of following sizes:
24.1 Supply, laying, testing & commissioning of 6.35 / 11 kV (E) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round
wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502 (Part-2) of following sizes:
24.2 Supply, laying, testing & commissioning 11 / 11 kV (UE) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip/ round wire
armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502(Part-2), of following sizes:
25.2 Supply, laying, testing & commissioning 6.6 / 6.6 kV (UE) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round
wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502(Part-2) of following sizes:
*6.6kV (UE) = 11kV (E)
26.1 Supply, laying, testing & commissioning of 3.3 / 3.3 kV (UE) grade, XLPE insulated, stranded Aluminium conductor, galvanised steel flat strip / round
wire armoured, extruded PVC type ST2 sheathed, heavy duty cable (to be laid on wall surface with necessary clamps / in existing cable trench / cable
trays / conduit / pipe sleeves at road crossing or floor as per site requirement) conforming to IS:7098 (Part-2) & IEC:60502 (Part-2) of following
sizes:* 3.3kV (E) = 3.3kV (UE)
a 3 Core x 70 Sqmm Meter 370 30 400 18% 472
28 Cable Glands:
Providing & fitting heavy duty brass cable glands (nickel-plated) with washers & rubber ring conforming to IS, suitable for 3, 3½ & 4 core cables of
following type & sizes:
28.1 Single Compression Brass Cable Glands
29 Cable Terminations / Jointing Kits for 1.1kV grade PVC/ XLPE Cable
Providing & fitting heat shrink cable termination/ jointing kits for 1.1kV grade PVC/ XLPE insulated cable including necessary earth connectivity
connection, material & consummables making the termination/ joint complete ensuring the joint resistance is within the permissble limit as per IS, of
following types & sizes:
29.1 Indoor / Outdoor End Termination Kit
sq mm core
d 185 to 300 3C/ 3.5C / 4C Each 629 575 1,204 18% 1,421
sq mm core
29.3 Straight Through Joints (Cold Applied Insulations & Sealing System)
d 120 to 185 3C/ 3.5C / 4C Each 1,760 700 2,460 18% 2,903
30 Cable Terminations / Jointing Kits for 3.3 kV (E/UE) / 6.6 kV (E) XLPE Cable
Providing & fitting heat shrink cable termination/ jointing kits for 3.3 kV (E/UE) / 6.6 kV (E) grade XLPE insulated cable including necessary earth
connectivity connection, material & consummables making the termination/ joint complete ensuring the joint resistance is within the permissble limit
as per IS, of following types & sizes:
30.1 Indoor Terminations Kit suitable for
31 Cable Terminations / Jointing Kits for 6.6 kV (UE) / 11 kV (E) grade XLPE Cable
Providing & fitting heat shrink cable termination/ jointing kits for 6.6 kV (UE) / 11 kV (E) grade XLPE insulated cable including necessary earth
connectivity connection, material & consummables making the termination/ joint complete ensuring the joint resistance is within the permissble limit
as per IS, of following types & sizes:
31.1 Indoor Terminations Kit suitable for
33.1 Supply, installation, testing & commissioning totally enclosed fan cooled squirrel cage induction motor, foot / flanged mounted enclosure having IP-55
degree of protection, continuously rated (S1) duty suitable for operation on 415 V ± 10%, 3 phase, 50Hz ± 5% AC supply with ambient temperature
500 C, Class F insulation (temperature rise limited to class B) conforming to high energy efficiency (IE-2) as per IS 12615:2011.
33.2 Supply, installation, testing & commissioning totally enclosed fan cooled squirrel cage induction motor, foot / flanged mounted enclosure having IP-
55 degree of protection, continuously rated (S1) duty suitable for operation on 415 V ± 10%, 3 phase, 50Hz ± 5% AC supply with ambient
temperature 50 deg. C, Class F insulation (temperature rise limited to class B) conforming to premium efficiency (IE-3) as per IS 12615:2011 and IS /
IEC 60034-1:2017.
A 2 Pole / 3000 RPM, Horizontal Foot Mounted (All ratings in kW)
34 LT Power Capacitor
34.1 Supply & erecting heavy duty APP type capacitor unit, vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in
internal fuses complete with discharge resistances & terminal cover, rated for 440 V AC, 3 Phase, 50Hz as per IS - 13585 Part-1.
APP type Capacitor kVAR 259 26 285 18% 336
35.1 Supply & laying MS ladder type cable trays with side channels of size - 75 x 15 x 15 mm / 100 x 15 x 15 mm & rungs of size - 35 x 15 x 15 mm
spaced at 250 mm apart, fabricated from 2 mm thick sheet steel in standard length of 2.5 meter, duly finished with one coat of red oxide & two coats
of aluminium paint as per IS including accessories such as coupler plates / fish plates, bends, tees, reducers, elbows, covers and electro-galvanized
hardware etc, erected on existing support as per specification and instruction of engineer in charge.
35.2 Supply & laying MS perforated type cable trays with returned edge/ flange, fabricated from 2.0 mm thk sheet steel in the standard length of 2.5 mtrs,
duly finished with one coat of red oxide & two coats of aluminium paint as per IS including accessories such as coupler plates / fish plates, bends,
tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on existing support as per specification and instruction of engineer in
charge.
a 100(W) x 35(H) x 2.0 mm Thick Rmt. 154 16 170 18% 201
C Supply & laying GI ladder type cable trays with side channels of size - 75 x 15 x 15 mm/ 100 x 15 x 15 mm & rungs of size - 35 x15 x 15 mm spaced
at 250 mm apart, fabricated from 2 mm thick sheet steel in standard length of 2.5 meter, duly hot dipped galvanized after fabrication as per IS 2629-
1989/ IS 4759-1984 including accessories such as coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized
hardware etc, erected on existing support as per specification and instruction of engineer in charge.
D Supply & laying GI perforated type cable trays with returned edge/ flange, fabricated from 2.0 mm thk sheet steel in the standard length of 2.5 mtrs,
duly hot dipped galvanized after fabrication as per IS 2629-1989 / IS 4759-1984 including accessories such as coupler plates/ fish plates, bends,
tees, reducers, elbows, covers and electro-galvanized hardware etc, erected on existing support as per specification and instruction of engineer in
charge.
a 100(W) x 35(H) x 2.0 mm Thick Rmt. 207 21 228 18% 269
E Supply & laying FRP ladder type cable trays with C shaped side channels of size - 75 x 25 x 25 mm for 150 mm wide and 100 x 75 x 75 mm for 300
mm wide & above, rungs of 25 mm square hollow tube spaced at 300 mm apart, manufactured as per NEMA FGI-1993 / IS 6746 - 1994/ ASTM-D
standards using corrosion resistant polyester flame retardant U.V stabilised resin & various types of glass fibres with glass content ≥ 55% with
minimum thickness of 3.0 mm for all sizes upto 150 mm (W) & 4.0 mm thickness for all sizes of 300 mm & above, supplied in standard length of 3 mtr
including accessories such as coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized / SS-304 hardware etc,
erected on existing support as per specification and instruction of engineer in charge.
F Supply & laying FRP perforated type cable trays manufactured as per NEMA FGI-1993 / IS 6746 - 1994/ ASTM-D standards using corrosion resistant
polyester flame retardant U.V stabilised resin & various types of glass fibres with glass content ≥ 55% with minimum thickness of 3.0 mm for all
sizes upto 150 mm (W) & 4.0 mm thickness for all sizes of 300 mm & above, supplied in standard length of 3 mtr including accessories such as
coupler plates/ fish plates, bends, tees, reducers, elbows, covers and electro-galvanized / SS-304 hardware etc, erected on existing support as per
specification and instruction of engineer in charge.
a 100(W) x 30(H) x 3mm thick Rmt. 147 15 162 18% 191
36 Rate per KW for comprehensive work of S.I.T.C. of Electro-mechanical components for headworks of R.W.S.S.(This is only for the purpose
of rough estimation)
A Electro mechanical components of Pumping Station having installed capacity up to ≤ 75 kW with working load not exceding 75 KW
Supply, installation, testing & commissioning of electro-mechanical equipments of water supply pumping system viz. pumping machinery
(of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows, flow meter (full
bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (motorised chain pulley block with
geared travelling trolley), vaccum pumps with accessories or horizontal mono submersible (drain) pump with accessories including LV
MCC - APFC panels, LT XLPE insulated Cu / Al armoured / PVC insulated round Copper submersible cables with tray & kits, earthing
system, fire extinguisher, Exhaust Fan, safety accessories etc. as per specifications.
2 End suction (Back Pull Out) KW 18,000 1,750 19,750 Incl. 19,750
B Electro mechanical components of Water Supply Pumping Station having installed capacity ranging from>75 kW to ≤ 200 KW with working
load exceding 75 KW but below 320 KW.
Supply, installation, testing & commissioning of electrical & mechanical equipments of water supply pumping system viz. pumping
machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows,
flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm)electromagnetic - For size ≤ 1400 mm) /
ultrasonic - For size ≥ 1500 mm), material handling system (EOT), vaccum pump with accessories or horizontal mono submersible (drain)
pump with accessories including 11 kV switchyard with dristribution transformer, LV MCC - APFC panels, HT / LT XLPE insulated Cu / Al
armoured / PVC insulated round Copper submersible cables with tray & kits, earthing system, fire extinguisher, exhaust fan safety
accessories etc. as per specifications.
C Electro mechanical components of Water Supply Pumping Station having installed capacity > 200 KW with working load exceding 320 KW.
Supply, installation, testing & commissioning of electrical & mechanical equipments of water supply pumping system viz. pumping
machinery (of following type & rating), valves (SV/BFV/DPCV), Suction-delivery-discharge header pipes & specials, expansion bellows,
flow meter (full bore electromagnetic - For size ≤ 1400 mm) / ultrasonic - For size ≥ 1500 mm), material handling system (EOT), vaccum
pumps with accessories or horizontal mono submersible (drain) pump with accessories, fire extinguisher, exhaust fan including 11 kV
switchyard with dristribution transformer, HT switchgear panel, LV MCC - APFC panels, HT / LT XLPE insulated Cu / Al armoured / PVC
insulated round Copper submersible cables with tray & kits, earthing system, safety accessories etc. as per specifications.
Note:- Rates are inclusive of all equipments / accessories required for satisfactory & Successful execution of electromechanical system in water supply
pumping system based on different type of pumping machinery but exclude cost of operation , maintanance & Repairs . Pleae refer basic &
mandatory electrical & mechanical component of water supply pumping system & design guide lines in brief attached here with
37.1 Providing & erecting Single girder type H.O.T. crane with geared travelling trolly with seven mtr lift complete with manually operated chain
pulley block, long travel rail track (40 mm sq. bar), moving or cross girder, brake, safety device, etc. & tested to 50% overload
Providing & erecting Single girder type fully electrically operated E.O.T. crane with electrically operated hoist, class II duty, geared
travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions
electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables form motor to
starter panel & other required accessories & tested as per IS Specifications.
Providing & erecting Double girder type fully electrically operated E.O.T. crane with electrically operated hoist, class II duty, geared
travelling trolley with seven meter lift complete with long travel rail track (40 mm sq. bar), moving or cross girder, all three motions
electrically operated by suitable rating motor IP 54, control panel & down pendant control block, brake, safety device, cables form motor to
starter panel & other required accessories & tested as per IS Specifications
Tonne m m m
Providing Chain pulley block with triple gear arrangement, lifting hook, laod chain & hand chain & locking device etc
40.2 Above 50 & up to 100 KVAR: APFC panel consisting following items.
a) 250 A, 50kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-250 A range analogue ammeter of 96 x 96 mm size with
selector switch
c) 3nos. 250 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB / MCB & Contactors for each capacitor bank
e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses
complete with discharge resistances & terminal cover) of approved make in required steps with well suited detuned reactor is placed in series with
each capacitor step. ( e.g., 100 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 10KVAR, 2 nos x 15 KVAR & 2 nos x 20 KVAR) f)
Enclosre dimensions- 2100 (H) x 1150 (W) x 600 (D)
As per above specification No 150,097 7,575 157,672 18% 186,053
40.3 Above 100 & up to 200 KVAR: APFC panel consisting following items.
a) 400 A, 50 kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-400 A range analogue ammeter of 96 x 96 mm size with
selector switch
c) 3nos. 400 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB / MCB & Contractors for each capacitor bank
e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses
complete with discharge resistances & terminal cover) of approved make in required steps with well suited detuned reactor is placed in series with
each capacitor step. (e.g., 200 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 15KVAR, 2 nos x 30 KVAR & 2 nos x 50 KVAR) f)
Enclosure dimensions- 2100 (H) x 1250 (W) x 600 (D)
40.4 Above 200 & up to 300 KVAR: APFC panel consisting following items.
a) 630 A, 50 kA for 1sec. TP, TM based MCCB with spreader terminals & rotary handle b) 0-630 A range analogue ammeter of 96 x 96 mm size with
selector switch
c) 3nos. 630/5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB/ MCB & Contractor for each capacitor bank
e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB/ non toxic oil, internally delta connected with built in internal fuses
complete with discharge resistances & terminal cover) of approved make in required steps (e.g., 300 KVAR capacity will be provided in steps of 2nos
x 5 KVAR, 2 nos x 10 KVAR, 2 nos x 15KVAR, 2 nos x 20 KVAR, & 4 nos x 50 KVAR) f) Enclosure dimensions- 1900 (H) x 1200 (W) x 600 (D)
40.5 Above 300 & up to 400 KVAR: APFC panel consisting following items.
a) 800 A, 50 kA for 1sec. TP, MDO type, ACB with TM based release & accessories b) 0-800 A range analogue ammeter of 96 x 96 mm size with
selector switch
c) 3nos. 800 / 5A, 10 VA CL-1.0 cast resin type current transformer d) Suitable rating of MCCB/ MCB & Contractor for each capacitor bank
e) Suitable rating APP type capacitor banks (vacuum impregnated with non-PCB / non toxic oil, internally delta connected with built in internal fuses
complete with discharge resistances & terminal cover) of approved make in required steps with well suited detuned reactor is placed in series with
each capacitor step. (e.g., 400 KVAR capacity will be provided in steps of 2 nos x 5 KVAR, 2 nos x 10 KVAR, 2 nos x 15KVAR, 2 nos x 20 KVAR & 6
nos x 50 KVAR) f) Enclosre dimensions- 2100 (H) x 1250 (W) x 1000 (D)
S.I.T.C of LV MCC Panel totally enclosed, dust & bermin proof, indoor type, minimum degree of protection - IP 52 as per IS: 2147, operation on 3-
Phase, 4 Wire, 415V, 50Hz, Neutral effectively grounded, with instrumentation compartments accomodating LED type indicating lamps, control
contactors as per IS: 13947, CT of accuracy class- I as per IS: 2705, relays, meters & control MCBs, air insulated electrolitic grade Aluminum busbar
for three phase & neutral system with incomming breaker- microprocessor based Air Circuit Breakers (electrically operated drawout type)/ air break
fixed type MCCB with trip free mechanism, current limiting type as per IS: 8828, Motor Contractor (as per type -2 coordination), Overload Relay with
built-in single phasing prevention feature & auxiliary feeders as per SLD drawings, momentary contact type push buttons, equipment fittings, bus
bars, cable boxes, cable gland, incoming & ougoing cable connection for 1100V grade, Aluminium/ Copper conductor XLPE/ PVC insulated & PVC
sheathed armoured cable, 10% spare terminals, power wiring using 1100V grade, FRLS insulated copper conductor wires conforming to IS: 694 &
8130, cable compartments/ alleys of minimum 300 mm size, GI earth bus bar for entire length. MCC shall be fabricated from cold rolled, coled
annealed (CRCA) sheet steel & minimum thickness of various members shall be as follows:
Base Frame/ Channel/ Gland Plate - 3 mm, Load Bearing Members/ Doors - 2 mm and Internal Partitions - 1.6 mm.
41.1 Auto Transformer Starter with MCCB, Contactor, O/L relay, cast resin type CT, Digital MFM, Analog Ammeter, SPP, Timer etc.
42.1 Supply, installation, testing & commissioning both side extensible, Indoor type HV Switchgear panel confirming to IS-3427, IS-2516 (Part-I & II.sec.1 )
& IEC-60056 & IEC-62271-100/200 for use on 3phase, 50 Hz, unearthed AC supply system and having breaking/ ruptuing capacity of 150 MVA (26.3
kA for 3sec) complete with spring charged mechanism, ON-OFF mechanical push button, operation counters, Breaker TNC switch, Breaker L/R
switch, necessary auxiliary switches, closing coil, shunt trip, protection relays & Indicators etc., complete.
The panel shall comprise of air insulated busbars provided with heat shrinkable PVC sleeves. The VCB trolley shall comprise of three vacuum
interrupters with epoxy support insulators and self aligning finger type isolating contacts and necessary mechanical interlocks, safety shutters,
isolating plugs. Enclosure shall be openable from front as well as rear end. The breaker shall be Manual cum motorised mechanism with following
accessories.
a) 96 x 96 mm square flush mounting type Ammeter & Volt meter with selector switches
b) Multi function meter
c) Double core, cast resin type current transofrmer having ratio as per requirement, one core for metering & one core for protection having required
class of accuracy.
d) Instantaneous under voltage relay & Temperature rise tripping Relay,
e) Triple pole IDMTL two over current and one earth fault relay with current setting range 50-200% and 10-40%
f) Electrical closing. coil & shunt trip coil operating on 110 V DC.
g) Auxiliary relay for anti pumping device.
h) Three limb, drawout type, feeder connected, cast resin insulated, three phase Potential transformer having ratio & burden as per reqirement &
Class 0.5 accuracy.
i) Annunciator Windows, Common Hooter / Alarm bell operating on 230 AC / 110 V DC
j) Cable boxes suitable to terminate 3 core XLPE cable of required size (As per design).
k) 230V A.C. to 110 V D.C.power pack for closing & tripping circuit common.
l) Breaker ON-OFF, Auto trip and spring charged indicators.
m) Phase indicating & panel illumination lamps with plug socket.
n) Space Heater with Thermostat.
a 3.3 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit Set 3,589,070 22,725 3,611,795 18.00% 4,261,918
breaker for 2 nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for
Motor Soft Starters, 2nos. O / G for 3.3 / 0.433kV Auxiliary
transformers
b 3.3 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit Set 3,589,070 22,725 3,611,795 18% 4,261,918
breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for
Motor Soft Starters, 2 nos. O/G for 3.3 / 0.433kV Auxiliary
transformers
c 3.3 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit Set 3,589,070 22,725 3,611,795 18% 4,261,918
breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for
Motor Soft Starters, 2nos. O/G for 3.3 / 0.433kV Auxiliary
transformers
d 3.3 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit Set 3,046,005 22,725 3,068,730 18% 3,621,101
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2nos. O / G for 3.3 / 0.433kV Auxiliary
transformers
e 3.3 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit Set 3,046,005 22,725 3,068,730 18% 3,621,101
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2nos. O/G for 3.3 / 0.433kV Auxiliary
transformers
f 3.3 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit Set 3,046,005 22,725 3,068,730 18% 3,621,101
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2nos. O / G for 3.3 / 0.433kV Auxiliary
transformers
b 6.6 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit Set 3,589,070 27,270 3,616,340 18.00% 4,267,281
breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for
Motor Soft Starters, 2 nos. O/G for 6.6 / 0.433kV Auxiliary
transformers
c 6.6 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit Set 3,066,964 27,270 3,094,234 18% 3,651,196
breaker for 2nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for
Motor Soft Starters, 2 nos. O/G for 6.6 / 0.433kV Auxiliary
transformers
d 6.6 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit Set 3,046,005 27,270 3,073,275 18% 3,626,465
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2 nos. O/G for 6.6 / 0.433kV Auxiliary
transformers
e 6.6 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit Set 3,046,005 27,270 3,073,275 18% 3,626,465
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2 nos. O/G for 6.6 / 0.433kV Auxiliary
transformers
f 6.6 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit Set 3,046,005 27,270 3,073,275 18% 3,626,465
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2nos. O/G for 6.6 / 0.433kV Auxiliary
transformers
42.3 Supply, installation, testing & commissioning both side extensible, Indoor type HV Switchgear panel confirming to IS-3427, IS-2516 (Part-I & II.sec.1 )
& IEC-60056 & IEC-62271-100/200 for use on 3phase, 50 Hz, unearthed AC supply system and having breaking/ ruptuing capacity of 500 MVA (26.3
kA for 3sec) complete with spring charged mechanism, ON-OFF mechanical push button, operation counters, Breaker TNC switch, Breaker L/R
switch, necessary auxiliary switches, closing coil, shunt trip, protection relays & Indicators etc., complete.
The panel shall comprise of air insulated busbars provided with heat shrinkable PVC sleeves. The VCB trolley shall comprise of three vacuum
interrupters with epoxy support insulators and self aligning finger type isolating contacts and necessary mechanical interlocks, safety shutters,
isolating plugs. Enclosure shall be openable from front as well as rear end.
The breaker shall be Manual cum motorised mechanism with following accessories.
a) 96 x 96 mm square flush mounting type Ammeter & Volt meter with selector switches
b) Multi function meter
c) Double core, cast resin type current transofrmer having ratio as per requirement, one core for metering & one core for protection having required
class of accuracy.
d) Instantaneous under voltage relay & Temperature rise tripping Relay,
e) Triple pole IDMTL two over current and one earth fault relay with current setting range 50-200% and 10-40%
f) Electrical closing. coil & shunt trip coil operating on 110 V DC.
g) Auxiliary relay for anti pumping device.
h) Three limb, drawout type, feeder connected, cast resin insulated, three phase Potential transformer having ratio & burden as per reqirement &
Class 0.5 accuracy.
i) Annunciator Windows, Common Hooter / Alarm bell operating on 230 AC/ 110 V DC
j) Cable boxes suitable to terminate 3 core XLPE cable of required size (As per design).
k) 230V A.C. to 110 V D.C.power pack for closing & tripping circuit common.
l) Breaker ON-OFF, Auto trip and spring charged indicators. m) Phase indicating & panel illumination lamps with plug socket. n) Space Heater with
Thermostat.
a 11 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit Set 3,589,070 31,815 3,620,885 18.00% 4,272,644
breaker for 2 nos. Incomer, 1no. Bus coupler, 8 nos. O/G feeders for
Motor Soft Starters, 2nos. O / G for 11 / 0.433kV Auxiliary
transformers
d 11 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit Set 3,046,005 31,815 3,077,820 18% 3,631,828
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2nos. O/G for 11 / 0.433kV Auxiliary transformers
e 11 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit Set 3,046,005 31,815 3,077,820 18% 3,631,828
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2nos. O/G for 11 / 0.433kV Auxiliary transformers
f 11 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit Set 3,046,005 31,815 3,077,820 18% 3,631,828
breaker for 2nos. Incomer, 1no. Bus coupler, 6 nos. O/G feeders for
Motor Soft Starters, 2 nos. O/G for 11 / 0.433kV Auxiliary
transformers
g 11 kV HV Switchgear Panel- Comprising of 1250 A Vacuum circuit Set 843,008 31,815 874,823 18% 1,032,291
breaker for 1no. Incomer, 2 nos. O / G feeders for 11/0.433kV
distribution transformers
h 11 kV HV Switchgear Panel- Comprising of 800 A Vacuum circuit Set 801,090 31,815 832,905 18% 982,828
breaker for 1no. Incomer, 2no. O / G feeders for 11/0.433kV
distribution transformers
i 11 kV HV Switchgear Panel- Comprising of 630 A Vacuum circuit Set 797,830 31,815 829,645 18% 978,981
breaker for 1no. Incomer, 2no. O / G feeders for 11/0.433kV
distribution transformers
j 11 kV HV ICOG Switchgear Panel- Comprising of 1250 A Vacuum Set 281,779 31,815 313,594 18% 370,041
circuit breaker for 1no. Incomer, 1no. O / G feeders for 11/0.433kV
distribution transformers
k 11 kV HV ICOG Switchgear Panel- Comprising of 800 A Vacuum Set 281,779 31,815 313,594 18% 370,041
circuit breaker for 1no. Incomer, 1no. O / G feeders for 11/0.433kV
distribution transformers
l 11 kV HV ICOG Switchgear Panel- Comprising of 630 A Vacuum Set 281,779 31,815 313,594 18% 370,041
circuit breaker for 1no. Incomer, 1no. O / G feeders for 11/0.433kV
distribution transformers
43 Solar System
43.1.1 Supply Solar PV Panels 900 wp, Each modules not less then 175 wp No. 47,277 Incl. 47,277 5% 49,641
should be in accordance with requirement of national & international
certificates such as IEC 61215 & 61730 for DC type Submersible
pump with MPPT controller.
43.1.2 Supply Solar PV Panels 1200 wp, Each modules not less then 175 61,553 Incl. 61,553 5% 64,630
wp should be in accordance with requirement of national &
international certificates such as IEC 61215 & 61730 for DC type
Submersible pump with MPPT controller.
43.1.3 Supply Solar PV Panels 1800 wp, Each modules not less then 175 94,554 Incl. 94,554 5% 99,282
wp should be in accordance with requirement of national &
international certificates such as IEC 61215 & 61730 for DC type
Submersible pump with MPPT controller.
43.1.4 Supply Solar PV Panels 2450 wp, Each modules not less then 175 171,456 Incl. 171,456 5% 180,029
wp should be in accordance with requirement of national &
international certificates such as IEC 61215 & 61730 for DC type
Submersible pump with MPPT controller.
43.2.1 Supply DC Submersible pump Discharge 7200 LPD for 90 Mtr. With 78,149 Incl. 78,149 12% 87,527
Controller Drive. MOC: SS 316
43.2.2 Supply DC Submersible pump Discharge 10000 LPD for 120 Mtr. 83,812 Incl. 83,812 12% 93,869
With Controller Drive. MOC: SS 316
43.2.3 Supply DC Voltage Submersible pump Discharge 10000 LPD for 170 93,558 Incl. 93,558 12% 104,785
Mtr. With Controller Drive.
43.2.4 Supply DC Submersible pump Discharge 10000 LPD for 200 Mtr. 103,000 Incl. 103,000 12% 115,360
With Controller Drive. MOC: SS 316
43.4.1 5 Years Comprehensive O&M work of above work with insurance of 15,434 Incl. 15,434 18% 18,212
all items like SPV Panel, Pump, Cable, G.I.Pipe, Controller etc for
entire period i.o. 05 years etc.900Wp
44 Providing Submerged centrifugal pumpsets(water immersed, dry air filled, class "F" insulated TEWC motor integrally mounted on volute
casing pumpsets for water duty, 3-phase, 50Hz±3%,415V±10% along with suitable foundation/ installation device with cable length from
pumps to panels & of following Material of Construction:
Impeller-CF8M, Casing-C.I. FG 260, Wearing Ring -SS, TC mechanical seal, CS/S.S.bearing, S.S shaft with sleeve, SS strainer & MS motor
body.
A Rating
1 Supply, installation, testing and commissioning LV Distribution Board (LVDB) totally enclosed, dust & vermin proof, indoor type, fabricated from
CRCA sheet steel with minimum thickness of 3 mm for base frame/ channel/ gland plates, 2.0 mm for load bearing members/ doors & 1.6 mm for
internal partitions, minimum degree of protection - IP 52 as per IS: 2147, suitable for operation on 3-Phase, 4 Wire, 415V, 50Hz, Neutral effectively
grounded, with instrumentation compartments accomodating meters, aux / protective relays, LED type indicating lamps & control MCBs as per IS:
13947, current & voltage transformers as per IS: 2705, air insulated electrolitic grade Aluminum/ Copper busbar for three phase & neutral system, GI
earth bus for entire length, power/ control wiring using 1100V grade, FRLS insulated copper conductor wires conforming to IS: 694 & 8130,
equipment fittings, horizontally running busbar compartment height of minimum 300 mm, incoming & ougoing cable connections for 1100V grade,
Aluminium/ Copper conductor XLPE/ PVC insulated & PVC sheathed armoured cable. LVDB shall have required incomming/ buscoupler/ outgoing
modules of following type & ratings.
Part-1
1.1 4000A, 3/ 4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of 70 kA
at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical protections & interlocks
etc. ACB Module shall have enclosure dimension: 2000 (H) x 1100 (W) x 1200 (D) & following technical features:
1.1a 3 pole, MDO with Thermal Magnetic Release No. 280,963 5,500 286,463 18% 338,026
1.1b 3 pole, EDO with Thermal Magnetic Release No. 301,527 5,500 307,027 18% 362,292
1.1c 3 pole, MDO with Microprocessor Release No. 286,995 5,500 292,495 18% 345,144
1.1d 3 pole, EDO with Microprocessor Release No. 307,558 5,500 313,058 18% 369,408
1.1e 4 pole, MDO with Thermal Magnetic Release No. 338,996 5,500 344,496 18% 406,505
1.1f 4 pole, EDO with Thermal Magnetic Release No. 359,536 5,500 365,036 18% 430,742
1.1h 4 pole, EDO with Microprocessor Release No. 365,567 5,500 371,067 18% 437,859
1.2 3200A, 3 / 4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu
of 60 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical
protections & interlocks etc. ACB Module shall have enclosure dimension: 2000(H) x 1100(W) x 1100 (D) & following technical features:
1.2a 3 pole, MDO with Thermal Magnetic Release No. 233,113 5,500 238,613 18% 281,563
1.2b 3 pole, EDO with Thermal Magnetic Release No. 255,991 5,500 261,491 18% 308,559
1.2c 3 pole, MDO with Microprocessor Release No. 241,162 5,500 246,662 18% 291,061
1.2d 3 pole, EDO with Microprocessor Release No. 262,497 5,500 267,997 18% 316,236
1.2e 4 pole, MDO with Thermal Magnetic Release No. 276,539 5,500 282,039 18% 332,806
1.2f 4 pole, EDO with Thermal Magnetic Release No. 297,078 5,500 302,578 18% 357,042
1.2g 4 pole, MDO with Microprocessor Release No. 282,570 5,500 288,070 18% 339,923
1.2f 4 pole, EDO with Microprocessor Release No. 303,110 5,500 308,610 18% 364,160
1.3 2500A, 3/ 4 Pole, ACB (Draw-out Type) with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of
60 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical
protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 900 (W) x 1100 (D) & following technical features:
1.3a 3 pole, MDO with Thermal Magnetic Release No. 176,843 5,500 182,343 18% 215,165
1.3b 3 pole, EDO with Thermal Magnetic Release No. 199,721 5,500 205,221 18% 242,161
1.3c 3 pole, MDO with Microprocessor Release No. 184,891 5,500 190,391 18% 224,661
1.3d 3 pole, EDO with Microprocessor Release No. 207,769 5,500 213,269 18% 251,657
1.3e 4 pole, MDO with Thermal Magnetic Release No. 214,664 5,500 220,164 18% 259,794
1.3f 4 pole, EDO with Thermal Magnetic Release No. 235,017 5,500 240,517 18% 283,810
1.3g 4 pole, MDO with Microprocessor Release No. 220,044 5,500 225,544 18% 266,142
1.3f 4 pole, EDO with Microprocessor Release No. 241,048 5,500 246,548 18% 290,927
1.4 2000A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of
50 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro-Mechanical
protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 900 (W) x 1100 (D) & following technical features:
Enclosure dimension: 2000(H) x 900(W) x 1100 (D)
1.4a 3 pole, MDO with Thermal Magnetic Release No. 146,991 5,500 152,491 18% 179,939
1.4b 3 pole, EDO with Thermal Magnetic Release No. 169,869 5,500 175,369 18% 206,935
1.4c 3 pole, MDO with Microprocessor Release No. 155,039 5,500 160,539 18% 189,436
1.4d 3 pole, EDO with Microprocessor Release No. 177,917 5,500 183,417 18% 216,432
1.4e 4 pole, MDO with Thermal Magnetic Release No. 185,987 5,500 191,487 18% 225,955
1.4f 4 pole, EDO with Thermal Magnetic Release No. 208,819 5,500 214,319 18% 252,896
1.4g 4 pole, MDO with Microprocessor Release No. 194,035 5,500 199,535 18% 235,451
1.4f 4 pole, EDO with Microprocessor Release No. 214,851 5,500 220,351 18% 260,014
1.5 1600A, 3 & 4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu
of 50 kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical
protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 800 (W) x 1000 (D) & following technical features:
1.5a 3 pole, MDO with Thermal Magnetic Release No. 122,474 5,500 127,974 18% 151,009
1.5b 3 pole, EDO with Thermal Magnetic Release No. 145,351 5,500 150,851 18% 178,004
1.5c 3 pole, MDO with Microprocessor Release No. 130,522 5,500 136,022 18% 160,506
1.5d 3 pole, EDO with Microprocessor Release No. 153,399 5,500 158,899 18% 187,501
1.5e 4 pole, MDO with Thermal Magnetic Release No. 151,559 5,500 157,059 18% 185,330
1.5g 4 pole, MDO with Microprocessor Release No. 159,607 5,500 165,107 18% 194,826
1.5h 4 pole, EDO with Microprocessor Release No. 182,485 5,500 187,985 18% 221,822
1.6 1250A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu
of 50kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical
protections & interlocks etc. ACB Module shall have enclosure dimension: 2000 (H) x 800 (W) x 1000 (D) & following technical features:
1.6a 3 pole, MDO with Thermal Magnetic Release No. 107,808 5,500 113,308 18% 133,703
1.6b 3 pole, EDO with Thermal Magnetic Release No. 130,685 5,500 136,185 18% 160,698
1.6c 3 pole, MDO with Microprocessor Release No. 115,857 5,500 121,357 18% 143,201
1.6d 3 pole, EDO with Microprocessor Release No. 138,734 5,500 144,234 18% 170,196
1.6e 4 pole, MDO with Thermal Magnetic Release No. 137,221 5,500 142,721 18% 168,411
1.6f 4 pole, EDO with Thermal Magnetic Release No. 160,098 5,500 165,598 18% 195,406
1.6g 4 pole, MDO with Microprocessor Release No. 145,270 5,500 150,770 18% 177,909
1.6h 4 pole, EDO with Microprocessor Release No. 168,147 5,500 173,647 18% 204,903
1.7 1000A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu
of 50kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical
protections & interlocks etc. ACB Module shall have enclosure dimension: 2000(H) x 800(W) x 1000 (D) & following technical features:
1.7a 3 pole, MDO with Thermal Magnetic Release No. 95,728 5,500 101,228 18% 119,449
1.7b 3 pole, EDO with Thermal Magnetic Release No. 118,606 5,500 124,106 18% 146,445
1.7c 3 pole, MDO with Microprocessor Release No. 103,776 5,500 109,276 18% 128,946
1.7d 3 pole, EDO with Microprocessor Release No. 126,654 5,500 132,154 18% 155,942
1.7e 4 pole, MDO with Thermal Magnetic Release No. 122,668 5,500 128,168 18% 151,238
1.7f 4 pole, EDO with Thermal Magnetic Release No. 145,545 5,500 151,045 18% 178,233
1.7g 4 pole, MDO with Microprocessor Release No. 130,715 5,500 136,215 18% 160,734
1.7h 4 pole, EDO with Microprocessor Release No. 153,593 5,500 159,093 18% 187,730
1.8 800A, 3 &4 Pole, ACB (Draw-out Type) with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) having breaking capacity Icu of
50kA at 415V with 6NO+6NC potential feee auxiliary contacts, secondary isolating contacts with all necessary Electro Mechanical
protections & interlocks etc.
ACB module shall have enclosure dimension: 2000 (H) x 800 (W) x 1000 (D) & following technical features.
1.8a 3 pole, MDO with Thermal Magnetic Release No. 90,810 5,500 96,310 18% 113,646
1.8b 3 pole, EDO with Thermal Magnetic Release No. 113,687 5,500 119,187 18% 140,641
1.8c 3 pole, MDO with Microprocessor Release No. 98,859 5,500 104,359 18% 123,144
1.8d 3 pole, EDO with Microprocessor Release No. 121,736 5,500 127,236 18% 150,138
1.8e 4 pole, MDO with Thermal Magnetic Release No. 115,722 5,500 121,222 18% 143,042
1.8f 4 pole, EDO with Thermal Magnetic Release No. 138,600 5,500 144,100 18% 170,038
1.8g 4 pole, MDO with Microprocessor Release No. 123,770 5,500 129,270 18% 152,539
1.8h 4 pole, EDO with Microprocessor Release No. 152,191 5,500 157,691 18% 186,075
1.9 Above 400A, upto & including 630A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS / IEC 60947-2 with trip free mechanism, current
limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC
potential free auxiliary contacts with all necessary Electro Mechanical protections & interlocks etc. MCCB module, when used as
Incommer/ Bus Coupler, shall have enclosure dimensions- 2000 (H) x 650 (W) x 600 (D) & following technical features:
1.9a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 33,460 4,000 37,460 18% 44,203
=100% of Icu), TM release
1.9b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 36,705 4,000 40,705 18% 48,032
=100% of Icu), Microprocessor release
1.9d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 34,701 4,000 38,701 18% 45,667
=100% of Icu), Microprocessor release
1.9e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 31,984 4,000 35,984 18% 42,461
=100% of Icu), TM release
1.9f 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 34,701 4,000 38,701 18% 45,667
=100% of Icu), Microprocessor release
1.9g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 40,609 4,000 44,609 18% 52,639
=100% of Icu), TM release
1.9h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 46,940 4,000 50,940 18% 60,109
=100% of Icu), Microprocessor release
1.9i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 38,017 4,000 42,017 18% 49,580
=100% of Icu), TM release
1.9j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 42,685 4,000 46,685 18% 55,088
=100% of Icu), Microprocessor release
1.9k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 38,017 4,000 42,017 18% 49,580
=100% of Icu), TM release
1.9l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 42,685 4,000 46,685 18% 55,088
=100% of Icu), Microprocessor release
1.10 Above 400A, upto & including 630A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS / IEC 60947-2 with trip free mechanism, current
limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC
potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as
Outgoing(s), shall have enclosure dimensions- 600 (H) x 600 (W) x 600 (D) & following technical features:
1.10a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 33,460 4,000 37,460 18.00% 44,203
=100% of Icu), TM release
1.10b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 36,705 4,000 40,705 18.00% 48,032
=100% of Icu), Microprocessor release
1.10c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 31,984 4,000 35,984 18% 42,461
=100% of Icu), TM release
1.10d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 34,701 4,000 38,701 18% 45,667
=100% of Icu), Microprocessor release
1.10e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 31,984 4,000 35,984 18% 42,461
=100% of Icu), TM release
1.10f 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 34,701 4,000 38,701 18% 45,667
=100% of Icu), Microprocessor release
1.10g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 40,609 4,000 44,609 18% 52,639
=100% of Icu), TM release
1.10h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 46,940 4,000 50,940 18% 60,109
=100% of Icu), Microprocessor release
1.10i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 38,017 4,000 42,017 18% 49,580
=100% of Icu), TM release
1.10j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 42,685 4,000 46,685 18% 55,088
=100% of Icu), Microprocessor release
1.10k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 38,017 4,000 42,017 18% 49,580
=100% of Icu), TM release
1.10l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 42,685 4,000 46,685 18% 55,088
=100% of Icu), Microprocessor release
1.11 Above 250A, upto & including 400A, 3 / 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current
limiting type with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC
potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as
Incommer/ Bus Coupler, shall have enclosure dimensions- 1800 (H) x 600 (W) x 600 (D) & following technical features:
1.11a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 29,145 4,000 33,145 18% 39,111
=100% of Icu), TM release
1.11b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 33,434 4,000 37,434 18% 44,172
=100% of Icu), Microprocessor release
1.11c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 26,969 4,000 30,969 18% 36,543
=100% of Icu), TM release
1.11d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 32,345 4,000 36,345 18% 42,887
=100% of Icu), Microprocessor release
1.11g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 34,380 4,000 38,380 18% 45,288
=100% of Icu), TM release
1.11h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 39,690 4,000 43,690 18% 51,554
=100% of Icu), Microprocessor release
1.11i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 31,690 4,000 35,690 18% 42,114
=100% of Icu), TM release
1.11j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 37,729 4,000 41,729 18% 49,240
=100% of Icu), Microprocessor release
1.11k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 31,690 4,000 35,690 18% 42,114
=100% of Icu), TM release
1.11l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 37,729 4,000 41,729 18% 49,240
=100% of Icu), Microprocessor release
1.12 Above 250A, upto & including 400A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current
limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC
potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as
Outgoing(s), shall have enclosure dimensions- 500 (H) x 600 (W) x 600 (D) & following technical features:
1.12a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 29,145 3,500 32,645 18% 38,521
=100% of Icu), TM release
1.12b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 33,434 3,500 36,934 18% 43,582
=100% of Icu), Microprocessor release
1.12c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 26,969 3,500 30,469 18% 35,953
=100% of Icu), TM release
1.12d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 32,345 3,500 35,845 18% 42,297
=100% of Icu), Microprocessor release
1.12e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 26,969 3,500 30,469 18% 35,953
=100% of Icu), TM release
1.12f 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 32,345 3,500 35,845 18% 42,297
=100% of Icu), Microprocessor release
1.12g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 34,380 3,500 37,880 18% 44,698
=100% of Icu), TM release
1.12h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 39,690 3,500 43,190 18% 50,964
=100% of Icu), Microprocessor release
1.12i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 31,690 3,500 35,190 18% 41,524
=100% of Icu), TM release
1.12j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 37,729 3,500 41,229 18% 48,650
=100% of Icu), Microprocessor release
1.12k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 31,690 3,500 35,190 18% 41,524
=100% of Icu), TM release
1.12l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 37,729 3,500 41,229 18% 48,650
=100% of Icu), Microprocessor release
1.13 Above 80A, upto & including 250A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS / IEC 60947-2 with trip free mechanism, current
limiting type with Thermal-Magnetic / Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC
potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as
Incommer/ Bus Coupler, shall have enclosure dimensions- 1800(H) x 600(W) x 600 (D) & following technical features:
1.13a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 24,830 3,500 28,330 18% 33,429
=100% of Icu), TM release
1.13b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 27,688 3,500 31,188 18% 36,802
=100% of Icu), Microprocessor release
1.13c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 23,370 3,500 26,870 18% 31,707
=100% of Icu), TM release
1.13d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 26,346 3,500 29,846 18% 35,218
=100% of Icu), Microprocessor release
1.13e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 21,246 3,500 24,746 18% 29,200
=100% of Icu), TM release
1.13g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 28,641 3,500 32,141 18% 37,926
=100% of Icu), TM release
1.13h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 32,923 3,500 36,423 18% 42,979
=100% of Icu), Microprocessor release
1.13i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 26,645 3,500 30,145 18% 35,571
=100% of Icu), TM release
1.13j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 31,894 3,500 35,394 18% 41,765
=100% of Icu), Microprocessor release
1.13k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 24,863 3,500 28,363 18% 33,468
=100% of Icu), TM release
1.13l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 31,894 3,500 35,394 18% 41,765
=100% of Icu), Microprocessor release
1.14 Above 80A, upto & including 250A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current
limiting type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC
potential free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as
Outgoing(s), shall have enclosure dimensions- 400 (H) x 600 (W) x 600 (D) & following technical features:
1.14a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 24,830 3,500 28,330 18% 33,429
=100% of Icu), TM release
1.14b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 27,688 3,500 31,188 18% 36,802
=100% of Icu), Microprocessor release
1.14c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 23,370 3,500 26,870 18% 31,707
=100% of Icu), TM release
1.14d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 26,346 3,500 29,846 18% 35,218
=100% of Icu), Microprocessor release
1.14e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 21,246 3,500 24,746 18% 29,200
=100% of Icu), TM release
1.14f 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 26,346 3,500 29,846 18% 35,218
=100% of Icu), Microprocessor release
1.14g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 28,641 3,500 32,141 18% 37,926
=100% of Icu), TM release
1.14h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 32,923 3,500 36,423 18% 42,979
=100% of Icu), Microprocessor release
1.14i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 26,645 3,500 30,145 18% 35,571
=100% of Icu), TM release
1.14j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 31,894 3,500 35,394 18% 41,765
=100% of Icu), Microprocessor release
1.14k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 24,863 3,500 28,363 18% 33,468
=100% of Icu), TM release
1.14l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 31,894 3,500 35,394 18% 41,765
=100% of Icu), Microprocessor release
1.15 Above 16A, upto & including 80A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting
type with Thermal Magnetic/ Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential
free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Incommer/ Bus
Coupler, shall have enclosure dimensions- 1800(H) x 500(W) x 600 (D) & following technical features:
1.15a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 14,110 3,500 17,610 18% 20,780
=100% of Icu), TM release
1.15b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 21,935 3,500 25,435 18% 30,013
=100% of Icu), Microprocessor release
1.15c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 12,046 3,500 15,546 18% 18,344
=100% of Icu), TM release
1.15d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 20,281 3,500 23,781 18% 28,062
=100% of Icu), Microprocessor release
1.15e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 11,715 3,500 15,215 18% 17,954
=100% of Icu), TM release
1.15g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 16,644 3,500 20,144 18% 23,770
=100% of Icu), TM release
1.15h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 25,564 3,500 29,064 18% 34,296
=100% of Icu), Microprocessor release
1.15i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 13,574 3,500 17,074 18% 20,147
=100% of Icu), TM release
1.15j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 23,045 3,500 26,545 18% 31,323
=100% of Icu), Microprocessor release
1.15k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 13,078 3,500 16,578 18% 19,562
=100% of Icu), TM release
1.15l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 23,045 3,500 26,545 18% 31,323
=100% of Icu), Microprocessor release
1.16 Above 16A, upto & including 80A, 3 & 4 Pole, Air Break Fixed MCCB conforms to IS/ IEC 60947-2 with trip free mechanism, current limiting
type with Thermal Magnetic / Microprocessor release (O / C, S / C & E / F) with adjustable settings & having minimum 2NO+2NC potential
free auxiliary contacts with all necessary Electro-Mechanical protections & interlocks etc. MCCB module, when used as Outgoing(s), shall
have enclosure dimensions- 300(H) x 500(W) x 600 (D) & following technical features:
1.16a 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 14,110 3,500 17,610 18.00% 20,780
=100% of Icu), TM release
1.16b 3 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 21,935 3,500 25,435 18% 30,013
=100% of Icu), Microprocessor release
1.16c 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 12,046 3,500 15,546 18% 18,344
=100% of Icu), TM release
1.16d 3 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 20,281 3,500 23,781 18% 28,062
=100% of Icu), Microprocessor release
1.16e 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 11,715 3,500 15,215 18% 17,954
=100% of Icu), TM release
1.16f 3 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 20,281 3,500 23,781 18% 28,062
=100% of Icu), Microprocessor release
1.16g 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 16,644 3,500 20,144 18% 23,770
=100% of Icu), TM release
1.16h 4 Pole, MCCB with Breaking Capacity of Icu=50 KA at 415V (Ics No. 25,564 3,500 29,064 18% 34,296
=100% of Icu), Microprocessor release
1.16i 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 13,574 3,500 17,074 18% 20,147
=100% of Icu), TM release
1.16j 4 Pole, MCCB with Breaking Capacity of Icu=36 KA at 415V (Ics No. 23,045 3,500 26,545 18% 31,323
=100% of Icu), Microprocessor release
1.16k 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 13,078 3,500 16,578 18% 19,562
=100% of Icu), TM release
1.16l 4 Pole, MCCB with Breaking Capacity of Icu=25 KA at 415V (Ics No. 23,045 3,500 26,545 18% 31,323
=100% of Icu), Microprocessor release
1.17 Add for No Load Compansation KVAR banks (APP type) with detuned filters, MCCB, Power Contractor , Auto/ manual control with
switching on delay timer, housed in lower most compartment of incomer/ buscoupler module(s). KVAR bank, selected based on kva
rating of associated transformer(s), shall be of following capacity.
1.17a 125 kVAR for 4000A Incomer- approx 5% kVAR of 2500 kVA No. 43,781 3,200 46,981 18% 55,438
Transformer rating
1.17b 100 kVAR for 3200A Incomer- approx 5% kVAR of 2000 kVA No. 34,280 3,200 37,480 18% 44,226
Transformer rating
1.17c 80 kVAR for 2500A Incomer - approx 5% kVAR of 1600 kVA No. 27,125 3,200 30,325 18% 35,784
Transformer rating
1.17d 62.5 kVAR for 2000A Incomer- approx 5% kVAR of 1250 kVA No. 20,959 3,200 24,159 18% 28,508
Transformer rating
1.17e 50 kVAR for 1600A Incomer - approx 5% kVAR of 1000 kVA No. 16,581 3,200 19,781 18% 23,342
Transformer rating
1.17f 40 kVAR for 1250A Incomer - approx 5% kVAR of 800 kVA No. 13,115 3,200 16,315 18% 19,252
Transformer rating
1.17g 31.5 kVAR for 1000A Incomer - approx 5% kVAR of 630 kVA No. 10,516 3,200 13,716 18% 16,185
Transformer rating
1.18 Add for providing indicating & measuring instruments complete with accessories, associated wiring & controls of following type & rating
1.18a R, Y & B Phase Indicating Lamps (63.5 / 110 / 230V AC) for Incoming No. 466 122 588 18% 694
module(s)
1.18b On/ Off/ Trip, spring charged , trip circuit healthy, Control Supply ON/ No. 512 122 634 18% 748
Healthy indicating lamps(24 / 110V DC or 110V AC) for ACB
controlled Incomming/ Buscoupler module(s).
1.18c On/ Off/ Trip, spring charged , trip circuit healthy indicating lamps (24- No. 512 122 634 18% 748
110V AC / DC) for ACB controlled Outgoing module(s).
1.18d On/ Off/ Trip, Control Supply ON/ Healthy Indicating lamps (24 / 110V No. 512 122 634 18% 748
DC or 110V AC) for MCCB controlled Incomming/ Buscoupler
module(s).
1.18e On/ Off/ Trip Indicating lamps(110 / 230V AC) for MCCB controlled No. 251 122 373 18% 440
Outgoing module(s).
1.18f 3 Ph, 4Wire Multifunction Meter, Class 1.0 or better, Flush Mounting- No. 7,731 140 7,871 18% 9,288
96 x 96 mm with RS 485 communication port for Incoming(s)/
Outgoings(s), as required.
1.18g AC Ameter, Analogue Type(96 x 96) & ASS for Incoming(s)/ No. 838 140 978 18% 1,154
Outgoings(s), as required.
1.18h AC Ameter, Analogue Type(144 x144) & ASS for Incoming(s)/ No. 1,616 140 1,756 18% 2,072
Outgoing(s), as required.
1.18i AC Ameter, Digital Type(96 x 96) with inbuilt ASS for Incoming(s)/ No. 1,616 140 1,756 18% 2,072
Outgoings(s), as required.
1.18j AC Voltmeter, Analogue Type(96 x 96) & VSS for Incoming(s)/ No. 838 140 978 18% 1,154
Outgoings(s), as required.
1.18k AC Voltmeter, Analogue Type(144 x 144) & VSS for Incoming(s)/ No. 1,616 140 1,756 18% 2,072
Outgoings(s), as required.
1.18l AC Volt meter, Digital Type(96 x 96) with inbuilt VSS for Incoming(s)/ No. 838 140 978 18% 1,154
Outgoings(s), as required.
1.18m Local/ Remote Selector Switch for ACB controlled Incommer/ Bus No. 433 140 573 18% 676
Coupler / Outgoings modules, as required.
1.18n TNC Switch for ACB controlled Incommer/ Bus Coupler / Outgoings No. 1,444 235 1,679 18% 1,981
modules, as required.
1.19 Add for providing instrument Transformers complete with accessories, associated wiring & controls, of following type & rating
1.19a Cast rasin insulated Current Transformer, Single Core with CTR 50- No. 838 145 983 18% 1,160
75/1A or 5A, 5-15VA, Class 1.0 or better for metering, as applicable
1.19b Resin Cast insulated Current Transformer, Double Core with CTR 50- No. 1,108 190 1,298 18% 1,532
75/1A or 5A, 5-15VA, Class 1.0 or better for metering/ 5P10 or better
for protection, as applicable
1.19c Resin Cast insulated Current Transformer, Single Core with CTR 100- No. 1,108 190 1,298 18% 1,532
150/1A or 5A, 5-15VA, Class 1.0 or better for metering, as applicable
1.19e Resin Cast insulated Current Transformer, Single Core with CTR 200- No. 1,253 190 1,443 18% 1,703
300/1A or 5A, 5-15VA, Class 1.0 for metering, as applicable
1.19f Resin Cast insulated Current Transformer, Double Core with CTR No. 1,281 190 1,471 18% 1,736
200-300/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/ protection,
as applicable
1.19g Resin Cast insulated Current Transformer, Single Core with CTR 400- No. 1,490 190 1,680 18% 1,982
1000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as applicable
1.19h Resin Cast insulated Current Transformer, Double Core with CTR No. 1,677 190 1,867 18% 2,203
400-1000/1A or 5A, 5-15VA, Class 1.0/ 5P10 for metering/ protection,
as applicable
1.19i Resin Cast insulated Current Transformer, Single Core with CTR No. 1,770 190 1,960 18% 2,313
1200-1500/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as
applicable
1.19j Resin Cast insulated Current Transformer, Double Core with CTR No. 1,770 190 1,960 18% 2,313
1200-1500/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/
protection, as applicable
1.19k Resin Cast insulated Current Transformer, Single Core with CTR No. 2,282 190 2,472 18% 2,917
1600- 3000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as
applicable
1.19l Resin Cast insulated Current Transformer, Double Core with CTR No. 2,282 255 2,537 18% 2,994
1600-3000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/
protection, as applicable
1.19m Resin Cast insulated Current Transformer, Single Core with CTR No. 2,609 295 2,904 18% 3,427
3200- 4000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering, as
applicable
1.19n Resin Cast insulated Current Transformer, Double Core with CTR No. 2,584 295 2,879 18% 3,397
3200-4000/1A or 5A, 5-15VA, Class 1.0 / 5P10 for metering/
protection, as applicable
1.19o Resin Cast insulated Voltage Transformer, Single Core with PTR 415/ No. 13,553 735 14,288 18% 16,860
root3/ 110/ root3, 50VA, Class 1.0 or better for metering, as
applicable
1.19p Resin Cast insulated Voltage Transformer, Double Core with PTR No. 13,553 735 14,288 18% 16,860
415/ root3/ 110V/ root3/ 110V/ root3, 50 VA, Class 1.0 or better for
metering / 3P for protection, as applicabke
1.20 Add for providing LT Single Phase Control Transformers(Tape wound, dry type, low reactance with good regulation at short time loads to provide
control suppply voltages for control circuits of AC Motor Starters and/ or auxiliary euipment not intended for direct connection to the main circuit)
complete with accessories, associated wiring & controls, of following type & rating
1.20a 3500 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 15,192 1,445 16,637 18% 19,632
1.20b 3500 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 15,192 1,445 16,637 18% 19,632
1.20c 3500 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 15,192 1,445 16,637 18% 19,632
1.20d 3000 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 13,097 1,445 14,542 18% 17,160
1.20e 3000 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 13,097 1,445 14,542 18% 17,160
1.20f 3000 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 13,097 1,445 14,542 18% 17,160
1.20g 2500 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 11,085 1,445 12,530 18% 14,785
1.20h 2500 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 11,085 1,445 12,530 18% 14,785
1.20i 2500 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 11,085 1,445 12,530 18% 14,785
1.20j 2000 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 10,386 1,160 11,546 18% 13,624
1.20k 2000 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 10,386 1,160 11,546 18% 13,624
1.20m 1500 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 8,803 1,160 9,963 18% 11,756
1.20n 1500 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 8,803 1,160 9,963 18% 11,756
1.20o 1500 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 8,803 1,160 9,963 18% 11,756
1.20p 1000 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 6,055 1,160 7,215 18% 8,514
1.20q 1000 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 6,055 1,160 7,215 18% 8,514
1.20r 1000 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 6,055 1,160 7,215 18% 8,514
1.20s 750 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 4,634 755 5,389 18% 6,359
1.20t 750 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 4,634 755 5,389 18% 6,359
1.20u 750 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 4,634 755 5,389 18% 6,359
1.20v 630 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 4,472 755 5,227 18% 6,168
1.20w 630 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 4,100 755 4,855 18% 5,729
1.20x 630 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 3,690 755 4,445 18% 5,245
1.20y 500 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 3,866 755 4,621 18% 5,453
1.20z 500 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 3,479 755 4,234 18% 4,996
1.20aa 500 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 3,131 530 3,661 18% 4,320
1.20ab 400 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 3,261 530 3,791 18% 4,473
1.20ac 400 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 3,060 530 3,590 18% 4,236
1.20ad 400 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 2,754 530 3,284 18% 3,875
1.20ae 350 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 2,980 530 3,510 18% 4,142
1.20af 350 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 2,809 530 3,339 18% 3,940
1.20ag 350 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 2,527 530 3,057 18% 3,607
1.20ah 300 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 2,766 530 3,296 18% 3,889
1.20ai 300 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 2,490 530 3,020 18% 3,564
1.20aj 300 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 2,241 530 2,771 18% 3,270
1.20ak 250 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 2,515 530 3,045 18% 3,593
1.20al 250 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 2,264 530 2,794 18% 3,297
1.20am 250 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 2,037 530 2,567 18% 3,029
1.20an 200 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 2,096 510 2,606 18% 3,075
1.20ao 200 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 2,096 510 2,606 18% 3,075
1.20ap 200 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 1,886 510 2,396 18% 2,827
1.20aq 150 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 1,770 510 2,280 18% 2,690
1.20ar 150 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 1,593 510 2,103 18% 2,482
1.20as 150 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 1,434 510 1,944 18% 2,294
1.20at 100 VA , 415 / 240V AC with Tapping ± 5% insteps of 2.5% No. 1,285 510 1,795 18% 2,118
1.20au 100 VA , 415 / 110V AC with Tapping ± 5% insteps of 2.5% No. 1,285 510 1,795 18% 2,118
1.20av 100 VA , 415 / 24V AC with Tapping ± 5% insteps of 2.5% No. 1,216 510 1,726 18% 2,037
Supply, installation, testing & commissioning HFSR (Harmonic Free Series Reactor) HV soft starter panel suitable for 3-phase squirrel cage induction
motor & provided with built in bypass terminal for pump control application by torque control method as per tender specification.
Soft Starter shall be operated on 3-phase, 50 Hz, fault Level 3KA for 1Sec., with Copper bus bar & enclosure fabricated from 2mm CRCA sheet steel,
solidly earthed neutral system earthing complete with following associated necessary equipments & accessories.
46.1 Voltage level (KV) & KW Rating Line Side HFSR Soft Starter
46.2 Voltage level (KV) & KW Rating Neutral Side HFSR Soft Starter
Supply, installation, testing & commissioning FCMA (Flux compensated magnetic amplifier) HV soft starter panel suitable for 3-phase squirrel cage
induction motor & provided with built in bypass terminal for pump control application by torque control method as per tender specification.
Soft Starter shall be operated on 3-phase, 50 Hz, fault Level 3KA for 1Sec., with Copper bus bar & enclosure fabricated from 2mm CRCA sheet steel,
solidly earthed neutral system earthing complete with following associated necessary equipments & accessories.
47.1 Voltage level (KV) & Line Side FCMA Soft Starter
KW Rating
a 3.3 315 KW No 462,645 18,180 480,825 18% 567,374
47.2 Voltage level (KV) & KW Rating Neutral Side FCMA Soft Starter
1 Supply, Installation, testing & commissioning Indoor type 11 KV, 630 No 745,200 22,220 767,420 18% 905,556
Amp., 21kA for 3 sec. SF6 type extensible and motorized 5 way
smart Ring Main Unit (RMU) complete with (2 VCB + 3 LBS) with
FRTU and FPI with IP Protection, as per IS
2 Supply, Installation, testing & commissioning Indoor type 11 KV, 630 No 605,475 22,220 627,695 18% 740,680
Amp., 21kA for 3 sec. SF6 type extensible and motorized 4 way smart
Ring Main Unit (RMU) complete with (2 VCB + 2 LBS) with FRTU and
FPI with IP Protection, as per IS
4 Supply, Installation, testing & commissioning Indoor type 11 KV, 630 No 605,475 22,220 627,695 18% 740,680
Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way smart
Ring Main Unit (RMU) complete with (3 VCB) with FRTU and FPI with
IP Protection, as per IS
5 Supply, Installation, testing & commissioning Indoor type 11 KV, 630 No 326,025 22,220 348,245 18% 410,929
Amp., 21kA for 3 sec. SF6 type extensible and motorized one way
smart Ring Main Unit (RMU) complete with LB and with FPI with IP
Protection, as per IS
6 Supply, Installation, testing & commissioning Indoor type 11 KV, 630 No 419,175 22,220 441,395 18% 520,846
Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way smart
Ring Main Unit (RMU) complete with (1 VCB + 2 LBS) with FRTU and
FPI with IP Protection, as per IS
7 Supply, Installation, testing & commissioning Outdoor type 11 KV, No 773,145 22,220 795,365 18% 938,531
630 Amp., 21kA for 3 sec. SF6 type non extensible and motorized 5
way smart Ring Main Unit (RMU) complete with (2 VCB + 3 LBS) with
FRTU and FPI with IP Protection, as per IS
8 Supply, Installation, testing & commissioning Outdoor type 11 KV, No 698,625 22,220 720,845 18% 850,597
630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 4 way
smart Ring Main Unit (RMU) complete with (2 VCB + 2 LBS) with
FRTU and FPI with IP Protection, as per IS
9 Supply, Installation, testing & commissioning Outdoor type 11 KV, No 698,625 22,220 720,845 18% 850,597
630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way
smart Ring Main Unit (RMU) complete with (3 VCB) with FRTU and
FPI with IP Protection, as per IS
10 Supply, Installation, testing & commissioning Outdoor type 11 KV, No 512,325 22,220 534,545 18% 630,763
630 Amp., 21kA for 3 sec. SF6 type extensible and motorized 3 way
smart Ring Main Unit (RMU) complete with (1 VCB + 2 LBS) with
FRTU and FPI with IP Protection, as per IS
11 Supply, Installation, testing & commissioning Outdoor type 11 KV, No 344,655 22,220 366,875 18% 432,913
630 Amp. 21kA for 3 sec. SF6 type extensible and motorized one way
smart Ring Main Unit (RMU) complete with LB and with FPI with IP
Protection, as per IS
12 Supply, Installation, testing & commissioning Outdoor type 11 KV, No 419,175 22,220 441,395 18% 520,846
630 Amp., 21kA for 3 sec. SF6 type extensible and motorized one
way smart Ring Main Unit (RMU) complete with VCB and FPI with IP
Protection, as per IS
Design, Supply, Installation, Testing, Commissioning of Full Bore Electromagnetic flow meter with factory calibration,
Inbuilt Battery Power Operated, flanged connection, Flow sensor, Indicator, transmitter and totaliser with all accessories
viz. surge arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:
I Flow Meter/ Sensor:
DC pulsed type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard, SS304/ Metallic Alloy
Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/ Inbuilt Grounding Electrode,
Neoprene/Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/ Carbon steel with Anticorrosive Paint
Coil Housing with Junction Box, CS flanges.
II Flow Transmitter/ Converter ( Remote Field Mounted):
Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display,
±0.5% accuracy at 0.3 to 4 m/sec velocity,
one scalable pulse/ one status, one Modbus output, one GPRS/ GSM output, IP 67 protection, Die cast aluminium/
polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger,
20 meters cable length for sensor to transmitter communication, Minimum 5 years battery lifetime, 3.6 VDC Non
Rechargeable Lithium-thionyl chloride/ Ni-Cd high power batteries, Hourly Basis Worldwide transmission of measured data
and events via e‐mail and SMS by integrated GSM/GPRS modem, Reliable data storage facility through integrated SD card
etc alongwith wall mounted/ stand mounted cabinet.
1B Full Bore Electromagnetic Flow Meter (Inbuilt Battery Power Operated)- PN 16.
For PN 16 rating, 10% rise in rate to be considere on rate of PN 10 rating Item (Item No. 1A)
Design, Supply, Installation, Testing, Commissioning of Full Bore Electromagnetic flow meter with factory calibrated,
Regular Power Operated, flanged connection, Flow sensor, Indicator, transmitter and totaliser with all accessories viz.
surge arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:
DC pulsed type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard, SS304/ Metallic Alloy
Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/ Inbuilt Grounding Electrode,
Neoprene/ Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/ Carbon steel with Anticorrosive Paint
Coil Housing with Junction Box, CS flanges.
II Flow Transmitter/ Converter ( Remote Field Mounted):
Microprocessor based, Modular design, 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display,
±0.5% accuracy at 0.3 to 4 m/sec velocity, 4 to 20 mA with HART/Modbus output, one scalable pulse, one status output,
IP 67 protection, Die cast aluminium/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window
enclosure, Inbuilt EEPROM and Data Logger, 20 meters cable length for sensor to transmitter communication etc
alongwith wall mounted/ stand mounted cabinet.
2A Full Bore Electromagnetic Flow Meter (Regular Power Operated)- PN 10
Design, Supply, Installation, Testing, Commissioning of Single/ Dual/ Four Path Insertion Ultrasonic flow meter working on
transit time principle, with factory calibrated and site verification, Regular Power Operated, Flow sensor, Indicator,
transmitter and totaliser with all accessories viz. surge arrestor, associated cables, cabinets, hardwares, etc complete as
per following specifications:
I Flow Meter/ Sensor:
2/ 4/ 8 nos insertion ultrasonic type sensor ( 1/ 2/ 4 Pair) with ball valve for online removal of sensors/ any other interaction/
retraction assembly, PN 16 pressure rating, SS 316 Sensor MOC, IP 68 Protection.
Design, Supply, Installation, Testing, Commissioning of Fixed Type, Single Path Clamp On Ultrasonic flow meter working on transit time
principle, with factory calibrated and site verification, Regular Power Operated, Flow sensor, Indicator, transmitter and totaliser with all
accessories viz. surge arrestor, associated cabled, cabinets, hardwares, etc complete as per following specifications:
2 nos magnetic clamp on ultrasonic type sensor ( 1 Pair) with SS belt according to pipe size and necessary fitting assembly, ABS/
Alluminium Alloy Sensor MOC, IP 68 Protection.
II Flow Transmitter/ Converter ( Remote Field Mounted):
4B for pipe size 100 TO 700 mm No 182,832 15,253 198,085 18% 233,740
4C for pipe size 750 TO 4000 mm No 185,047 15,438 200,485 18% 236,572
Design, Supply, Installation, Testing, Commissioning of Portable Type, Single Path Clamp On Ultrasonic flow meter
working on transit time principle, with site verification, Inbuilt Battery Power Operated, Flow sensor and Hand Held Indicator
with all accessories viz. battery charger, associated cabled, portable case, hardwares, etc complete as per following
specifications:
I Flow Meter/ Sensor:
2 nos magnetic clamp on ultrasonic type sensor ( 1 Pair) with SS belt according to pipe size and necessary fitting assembly,
ABS/ Alluminium Alloy Sensor MOC, IP 68 Protection.
Design, Supply, Installation, Testing, Commissioning of Accoustic Doppler Type flow meter, working on transit time
principle, with site verification, Regular Power Operated, Flow sensor with Mounting Stand, Indicator, Transmitter and
totalizer with all accessories viz. associated cabled, cabinets, hardwares, etc complete as per following specifications:
I Flow Meter/ Sensor:
Accoustic Doppler type Flow Meter with real time acoustic doppler current meter with RS232/serial digital interface(SDI)-12
interface, features programmable range selection, vertical acoustic beam for water level measurement, multi cell current
profiling, integrated temperature sensor, pressure sensor, memory storage an mounting stand.
II Flow Indicator/ Converter ( Hand Held):
Microprocessor based, Modular design, Regular power Operated,
minimum 2 line LCD for indication of actual flow rate, forward, reverse, sum totaliser display,
±1% accuracy at 0.3 to 4 m/sec velocity,
One current(4-20mA) with HART output, one scalable pulse, one status output, RS 232 output,
IP 65/ 67 protection,
Die cast aluminum/ polycarbonate/ SS316 with Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM
and Data Logger,
20 meters cable length for sensor to transmitter communication.
Instrument shall have facility to connect with GPRS/ VHF/ VSAT modem.
6A Canal Depth 3- 5 Meter and width 5 - 10 No 1,002,250 83,614 1,085,864 18% 1,281,320
meter
6B Canal Depth 3- 20 Meter and width 20 - 25 No 1,126,740 94,000 1,220,740 18% 1,440,473
meter
7 Water Meters (Multijet/ Woltman Type):
7.3 METER READING DEVICE (For Manual Meter Reading / AMR Compatible / AMR Meter Reading)
Hand Held Unit / Meter Reading Device having IP 65 Protection class, windows/ android software base operating system,
minimum 1 GB RAM and 8 GB Flash Disk, GPRS / 3G / LTE network connectivity, GPS facility, Camera facility, data store
facility,
METER READING DEVICE/ Hand Held Unit No 121,325 - 121,325 18% 143,164
8.3 Strainer:
Design, Supply, Installation, Testing, Commissioning of External Striner for Woltman type Bulk Water Meter, Body: IS:210
FG200 , Strainer Frame : SS Perforated Sheet, SS 304, Mesh (30) : 58 Perforated Sheet, SS 304, Gasket: Rubber Cover:
IS:210FG200, Stud/Bolts/Nut: IS:1363CL4.6 & CL 4.0, Eye Bolt: IS:1363CL4.6 & CL4.0, Plug:13% CR.SS (AISI 410),
Flange Dimensions as per IS:1538 table 6/ BS-4504 PN16, with all necessary hardware to complete the installtion.
9 Bulk Water Meters (Ultrasonic)/ Full Bore Inline Ultrasonic Flow Meter:
9.1 Full Bore Inline Ultrasonic Flow Meter- Inbuilt Battery Power/ Self Power operated (PN 16)
Design, Supply, Installation, Testing, Commissioning of Full Bore Inline Ultrasonic flow meter with factory calibrated, Inbuilt
Battery Power Operated, flanged connection, Flow sensor, Indicator, transmitter and totaliser with all accessories viz. surge
arrestor, associated cables, cabinets, hardwares, etc complete as per following specifications:
Flow Meter/ Sensor: Ultrasonic type, IP 68 Protection, Flanged process connection as per IS 1538 or equivalent standard,
SS304/ Metallic Alloy Flow Tube, SS316/ SS 316 L/ Hastelloy Sensor, SS316/ Hastelloy Grounding Ring/ Inbuilt Grounding
Electrode, Neoprene/Polyurethane/ Hard Rubber/ Rilsan lining, SS304/ Die Cast Aluminium/ Carbon steel with Anticorrosive
Paint Coil Housing with Junction Box, CS flanges.
Flow Transmitter/ Converter ( Remote Field Mounted inside the Cabinet): Microprocessor based, Modular design, 2 line LCD
for indication of actual flow rate, forward, reverse, sum totaliser display, ±0.5% accuracy at 0.3 to 4 m/sec velocity, one
scalable pulse, one status, one GPRS/ GSM output, IP 67 protection, Die cast aluminium/ polycarbonate/ SS316 with
Anticorrosive Paint/ PU finish with glass window enclosure, Inbuilt EEPROM and Data Logger,20 meters cable length for
sensor to transmitter communication, Minimum 5 years battery life time, 3.6 VDC Non Rechargeable Lithium-thionyl
chloride/ Ni-Cd high power batteries, Real time data logging at remote location with every 1 minute frequency for storage up
to 30 days period and Twice a day transmission of measured data and events via e‐mail and SMS as & when they occur by
integrated GSM/GPRS modem, Reliable data storage facility through integrated SD card 32 GB.
10.2 Design, Supply, Installation, Testing, Commissioning of Diaphragm sealed Pressure Gauge, ±1% accuracy, Direct bottom
1/2" NPT (M) process connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type Bezel, SS316 L Diaphragm,
SS316 Bottom Housing Material, SS 316 Movement material, Aluminium dial with black graduation on white background,
Micro Zero adjustable pointer, neoprene gasket, Blow out disc, shatter proof glass, SS tag plate etc as per IS 3624.
10.3 Design, Supply, Installation, Testing, Commissioning of Vacuum Gauge, ±1% accuracy, Direct bottom 1/2" NPT (M)
process connection, IP 67, Glycerine filled, SS304 Case with Bayonet Type Bezel, SS316 L Bourdon Tube, SS 316
Movement material, Aluminium dial with black graduation on white background, Micro Zero adjustable pointer, neoprene
gasket, Blow out disc, shatter proof glass, SS tag plate etc as per IS 3624.
11 Pressure Transmitter:
Design, Supply, Installation, Testing and Commissioning of Sealed Diaphragm Type Pressure Transmitter.
Piezo-resistive sensor technolgy based pressure transmitter with Micro-processor based integral LED/ LCD display, with
accuracy of ± 0.3% of span, external zero and span adjustment, self diagnostics, temperature sensor for compensation. 15
to 36 V DC power supply, output signal of 4-20 mA DC with HART. Minimum IP 65 degree of protection. Aluminium housing
with epoxy coating, Accessories like snubbers for pump discharge applications, three way manifold, mounting brackets,
name plate etc. Material for accessories shall be SS. Protection Box/Canopy shall be provided for outside installed
transmitters.
Pressure Transmitter shall be suitable for following Range.
Design, Supply, Installation, Testing and Commissioning of Top mounted Displacer Type level switches with 2 nos SPDT
contacts of Micro switch rated 5 A, potential free power supply, Material of wetted parts shall be SS 316 and the material of
accessories shall be SS. IP 65 or equivalent degree of protection for enclosure, suitable for sump, ESR, tank, vessels
and underground reservoirs. The top mounted level switches shall be supplied with still tubes to suit the requirement.
. Accessories like name plate, mating flange, gaskets, fasteners, bolts & nuts, etc. shall be supplied with the Level
Switch of following Range.
650/1100 Volts, Armoured or un-Armoured Aluminium Conductor Cables as per IS:3961 (PART II)-1967
Current-carrying capacities and associated voltage drops for single-core p.v.c insulated cables.
Installation methods (Enclosed) Installation methods (Clipped Direct) Installation method (Defined Conditions)
Flat or vertical (2 cables, single-
2 Cables 3 or 4 cables 2 Cables single-phase 3 or 4 cables phase a.c. or d.c. or 3 or 4 cables 3 or 4 cables
Conductor single-phase a.c or d.c three-phase a.c a.c or d.c three-phase a.c three-phase) three-phase a.c
cross Current Volt drop Current Volt Current Volt drop Current Volt Current current Volt
Sectional carrying per carrying drop carrying per ampere carrying drop carrying Volt drop per ampere carrying drop
Area capacity ampere capacity per capacity per metre capacity per per metre capacity per
per metre ampere ampere capacity ampere
per per Single d.c. Three per
metre metre Phase metre
Phase
1 2 3 4 5 6 7 8 9 10 11 12 12 14 15
mm2 A mV A mV A mV A mV A mV mV A
1 14 42 12 37 17 42 16 0.37 - - - - - -
1.5 17 28 14 24 21 28 20 0.24 - - - - - -
2.5 24 17 21 15 30 17 26 0.15 - - - - - -
4 32 11 29 9.2 40 11 36 9.2 - - - - - -
6 41 7.1 37 6.2 50 7.1 45 6.2 - - - - - -
10 55 4.2 51 3.7 68 4.2 61 3.7 - - - - - -
16 74 2.7 66 2.3 90 2.7 81 2.3 - - - - - -
25 97 1.7 87 1.5 118 1.7 106 1.5 - - - - - -
35 119 1.3 106 1.1 145 1.3 130 1.1 - - - - - -
CORRECTION FACTORS
FOR AMBIENT TEMPERATURE
Ambient Temperature 25°C 35°C 40°C 45°C 50°C 55°C 60°C 65°C
Correction factor 1.06 0.94 0.87 0.79 0.71 0.61 0.5 0.35
GI Approx Approx
Area Nominal
Cond. Weight Resistance
mm2 Dia mm
Size Kg/M Ohm/M.
Typical
Approximate DOL Starter/
KW Relay Backup Typical
HP 3 Phase Full Load Contactor
415V Scale in HRC Cable size
415V 50 HZ current in capacity in
50 HZ Amps fuse in sq.mm AL
Amps Amps.
Amps
0.50 0.4 1 12 0.8-1.6 6 1.5/2.5
0.75 0.55 1.5 12 1-1.5 6 1.5/2.5
1 0.75 2 12 1.4-2 10 1.5/2.5
1.5 1.1 2.6 12 2-3 10 1.5/2.5
2 1.5 3.5 12 2.5-4 15 1.5/2.5
3 2.25 5 16 4-6 20 1.5/2.5
4 3 6.2 16 4-6 20 1.5/2.5
5 3.75 7.5 16 5.5-8 25 2.5
6 4.5 9 16 6-10 25 2.5
7.5 5.6 11 16 8-12 25 4
10 7.5 14 16 11-12 35 4
12.5 9.3 18 30 14-20 50 6
15 11 21 30 17-25 50 6
17.5 13 24 30 20-32 63 10
20 15 28 30 22-32 63 10
25 18.5 35 38 25-40 80 16
30 22 40 70 30-45 100 25
35 26 47 70 38-63 125 25
40 30 55 70 38-63 125 25
45 33.5 60 70 45-70 160 35
50 37.5 66 70 50-90 160 35
60 45 80 105 50-90 160 50
75 56 100 105 70-110 200 70
90 67.5 120 170 90-150 250 95
120-
100 75 135 170 155 250 95
140-
150 112 200 400 200 350 185
210-
200 150 275 400 300 500 300/400
280-
225 170 300 400 300 600 300/400
SIZE OF CAPACITORS IN KVAR REQUIRED FOR GIVEN DEGREE OF POWER FACTOR CORRECTION PER
KW OF LOAD
Initial Correction to
Power 0.85 0.9 0.95 0.98 Unity
1 2 3 4 5 6
0.50 1.112 1.248 1.403 1.529 1.732
0.51 1.066 1.202 1.357 1.483 1.686
0.52 1.024 1.16 1.315 1.441 1.644
0.53 0.98 1.116 1.217 1.397 1.6
0.54 0.939 1.075 1.23 1.356 1.559
0.55 0.899 1.035 1.19 1.316 1.519
0.56 0.86 0.996 1.151 1.277 1.48
0.57 0.822 0.958 1.113 1.239 1.442
0.58 0.785 0.921 1.076 1.202 1.405
0.59 0.748 0.884 1.039 1.165 1.368
0.60 0.714 0.849 1.005 1.131 1.334
0.61 0.679 0.815 0.97 1.096 1.299
0.62 0.645 0.781 0.936 1.062 1.265
0.63 0.613 0.749 0.904 1.03 1.233
0.64 0.58 0.716 0.871 0.997 1.2
0.65 0.549 0.685 0.84 0.966 1.169
0.66 0.518 0.654 0.809 0.935 1.138
0.67 0.488 0.624 0.779 0.905 1.108
0.68 0.459 0.595 0.75 0.876 1.079
0.69 0.429 0.565 0.72 0.84 1.049
0.70 0.4 0.536 0.691 0.811 1.02
0.71 0.372 0.508 0.663 0.783 0.992
0.72 0.343 0.479 0.634 0.754 0.963
0.73 0.316 0.452 0.607 0.727 0.936
0.74 0.289 0.425 0.58 0.7 0.909
0.75 0.262 0.398 0.553 0.673 0.882
0.76 0.235 0.371 0.526 0.652 0.855
0.77 0.209 0.345 0.5 0.62 0.829
0.78 0.183 0.319 0.473 0.594 0.803
0.79 0.156 0.292 0.447 0.567 0.776
0.80 0.13 0.266 0.421 0.541 0.75
0.81 0.104 0.24 0.395 0.515 0.724
0.82 0.078 0.214 0.369 0.489 0.698
0.83 0.052 0.188 0.343 0.463 0.672
Initial
Power Correction to
0.85 0.9 0.95 0.98 Unity
1 2 3 4 5 6
0.84 0.026 0.162 0.317 0.437 0.645
0.85 - 0.136 0.291 0.417 0.62
0.86 - 0.109 0.264 0.39 0.593
0.87 - 0.083 0.238 0.364 0.567
0.88 - 0.054 0.209 0.335 0.538
0.89 - 0.028 0.183 0.309 0.512
0.90 - - 0.155 0.281 0.484
0.91 - - 0.124 0.25 0.453
0.92 - - 0.097 0.223 0.426
0.93 - - 0.066 0.192 0.395
0.94 - - 0.034 0.16 0.363
0.95 - - - 0.126 0.329
0.96 - - - 0.089 0.292
0.97 - - - 0.047 0.25
0.98 - - - - 0.203
0.99 - - - - 0.143
Total kVAR Required=100 x [tan (0.55) - tan (0.20)] = 100 x (0.619-0.203) = 100 x 0.416
DISTRIBUTION TRANSFORMER
(1) Oil Test: 30 kV. Minimum across 2.5 mm gap for one minute.
(2) Insulation test: Minimum safe insulation resistance of windings at temperature.
30°C 40°C 50°C 60°C Voltage of
Meggar
415V 200 mΩ 100 50 25 500 Volts
3.3 & 6.6 kV 400 mΩ 200 100 50 1000 Volts
11 kV,22 kV 500 mΩ 250 125 65 2500 Volts
& 33 kV
(3) Ratio Test: 400V should be applied to HT side and Voltage to be measured on LT side. The ratio
should compare with the rated figures.
(4) Oil Level: Oil level should be checked up and topped if necessary.
(5) Breather: The silica in the breather should be blue.
(6) Diaphram: It should be in tact, and no crack is observed.
(7) Measurement of earth resistance: this should be less than 1 ohm.
Characteristic Limit
Sludge formation (Maximum) 0.3%
Moisture at 15.5°C 200 Redwood seconds
Moisture Nil
Dielectric strength 30 kV at 15°C to 20°C using 1/3 mm.
Diameter sphere, 2.5 mm apart
Flash Point (Minimum) 145°C
Evaporation (Maximum) 1.6%
Cold test -30°C
Acidity (Neutralization value)
Inorganic Nil
Organic (Max) 0.5 mg KoH/gram of oil
(1) When the acidity is less than 0.2 Mg/KOH/Gm. Of oil, the oil is in good condition from the stand
point of this test.
(2) When the acidity is between 0.2 mg and 0.5 mg/KOH/gm, no action need to be taken, if the oil is
satisfactory in all other respects.
(3) When the acidity is between 0.5 to 1.0 Mg/KOH/gm the oil should be kept under observation
and filtered if necessary.
(4) When the acidity exceeds 1 Mg/KOH/gm the oil should be reclaimed or discarded.
TYPE DESGINATION AND CORE IDENTIFICATION OF CABLES & WIRE AS PER IS: 1554 (1) & IS: 7098 (1)
2. Crimping Joints
a. Length f insulation to be stripped= barrel length+1-3 mm.
b. For cable size of 35 mm2 & above two/three clamps are recommended @ 3-4 mm distance.
EN 60529 outlines an international classification system for sealing effectiveness of enclosures of electrical
equipment against the intrusion into the equipment of foreign bodies (i.e tools, dust, fingers) and
moisture. This classification system utilizes the letters “IP” (“Ingress Protection”) followed by two or three
digits. (A third digit is sometimes used. An “X” is used for one of the digits if there is only one class of
protection; i.e IPX4 which addresses moisture resistance only).
The first digit of the IP code indicates the degree that persons are protected against contact with moving
parts (other than smooth rotating shafts, etc.) and the degree that equipment is protected against solid
foreign bodies intruding into an enclosure.
0 No special protection
1 Protection from a large part of the body such as a hand (but no protection from deliberate
access); from solid objects greater than 50 mm in diameter.
2 Protection against fingers or other object not greater than 80mm in length and 12 mm in
diameter.
3 Protection from entry by tools, wires, etc. with a diameter of thickness greater than 1 mm.
4 Protection from entry by solid objects with a diameter or thickness greater than 1 mm.
5 Protection from the amount of dust that would interfere with the operation of the equipment.
6 Dust tight
The second digit indicates the degree of protection of the equipment inside the enclosure against the
harmful entry of various forms of moisture. (e.g. dripping, spraying, submersion, etc.)
0 No special protection
1 Protection from dripping water
2 Protection from vertically dripping water
3 Protection from sprayed water
4 Protection from splashed water
5 Protection water projected from a nozzle.
6 Protection against heavy seas, or powerful jest of water
7 Protection against immersion
8 Protection against complete, continuous submersion in water.
Submersion depth and time must be specified by the end-user. The requirement must be more onerous
than IP 67.
IS CODES
ELECTRICAL WORKS
IS 2551 Danger Notice Boards
IS 4064 Normal duty air break switches & composite units of air break switches & fuses for
voltages not exceeding 1000V
IS 1818 Alternating current isolators (disconnectors) & earthing switch
IS 2584 Test for Electrical Strength
IS 694 PVC insulated cables.
IS 375 Specification for marking and arrangement for switchgear busbar, main connection
and aux. wiring
IS 5216 Safety procedures & practice in electrical works
IS 2982 Copper conductors in insulated cable & chords
IS 5578 Guide for marking of insulated conductor
IS 1951 Polyvinyl chloride sleeving for electrical purposes
IS 3010 Part-I appliances-connectors
IS 3010 Part-II appliances-inlets
IS 2268 Electrical call bells and buzzers for indoor use.
IS 3412 Electrical water boilers
IS 302 Light electrical appliances
IS:2882 Storage type automatic electric water heaters
IS:3202 Climate proofing of electrical equipment code of practice
IS:732 Electrical wiring installation (System voltage not exceeding 650V) code of practice.
IS:3106 Selection, installation and maintenance of fuses (System voltage not exceeding
650V) code of practice.
IS:374 Fan and regulators ceiling type, electric
IS:1258 Bayonet lamp holders
IS:2086 carriers and bases used in rewireable type electric fuses up to 650V
IS:5561 Electric power connectors
IS:2675 Enclosed distribution fuse boards and cutouts for voltage not exceeding 1000V
IS:2208 HRC Cartridge fuse link up to 650V
IS:3961 Recommended current rating for Cables PVC insulated and PVC (Part-II) Sheathed
heavy duty
IS:371 Ceiling roses
IS:5987 Selection of switches (Voltage not exceeding 1000V) Code of Practice
IS:1646 Protection for fire safety of building Electrical installation
IS:3106 Selection, Installation of fuses (Voltage not exceeding 650V)
IS:5133 Part-I Boxes for enclosure of electrical accessories steel and cast-iron boxes
IS:5133 Part-I boxes made of insulated materials
IS:5649 Adaptors for flexible steel conduits
IS:419 Fittings for rigid non-metallic conduits
IS:4160 Interlocking switch socket outlet
IS:2412 Link clips for electrical wiring
IS:2509 Rigid non-metallic conduits for electrical installation
IS:8623 Factory built accessories of Switchgear & Control gear for voltage up to and including
1000V AC and 1200V DC
IS:4648 Electrical layout in residential buildings
IS:2501 Copper tubes for general residential purposes
IS:1259 Mild steel tubes
IS:2667 Specifications for lightning protection against building and allied structures
IS:2309 Code of practice for lightning protection against building and allied structure
IS:3043 Code of practice for earthing
IS:2274 Electrical wiring installation (Voltage exceeding 650V)
IS:1653 Rigid steel conduits for electrical wiring (revised) with amendments
IS:1915 General and safety requirements for electrical lighting fitting
IS:5316 Guide for safety procedures and practices in electric works
IS:5124 Code of practice for installation and maintenance for AC induction motor starters
(Voltage not exceeding 1000V)
IS:1180 Outdoor type three phase distribution transformer
IS:5133 Boxes for enclosures of electrical accessories
BS British Standard
IS 6784:1996 Methods for Performance Testing of Water Meters (Domestic Type) (Second
Revision)
BS 7405: 1991 BS 7405 classifies closed conduit flow meters
ISO 4185:1980 Specifies a method of determining the liquid flow-rate by measuring the mass of
liquid delivered into a weighing tank in a known time interval
ISO 4064- International Organization For Standardization for Water meters for cold potable
1:2014 water and hot water
-- Part 1: Metrological and technical requirements
ISO 4064- Water meters for cold potable water and hot water
2:2014 -- Part 2: Test methods
ISO 4064- Water meters for cold potable water and hot water
3:2014 -- Part 3: Test report format
ISO 4064- Water meters for cold potable water and hot water
4:2014 -- Part 4: Non-metrological requirements not covered in ISO 4064-1
ISO 4064- Water meters for cold potable water and hot water
5:2014 -- Part 5: Installation requirements
ISO/ IEC: General requirements for the competence of testing and calibration laboratories
17025
ISO 6817 Measurement of conductive liquid flow in closed
conduit- Methods using Electromagnetic Flow meter
ISO Measurement of fluid flow in closed conduits-
12242:2012 Ultrasonic transit time flow meters
ISO 7066-2 Assessment of uncertainty in the calibration & use of flow measurement device
ISO 3834-2: Quality requirements for fusion welding of metallic materials. Comprehensive quality
2005 requirements
IS 3043-2007 Code of practice for Safety Earthing
Item Description
No
01 ACSR DOG CONDUCTOR
02 LIGHTNING ARRESTOR
03 11KV STRAIN INSULATOR DISC
04 11KV INSULATOR WITH PIN -5KN
05 11KV, 200A AB SWITCH WITH EARTH SWITCH
06 11KV 25A DO FUSE
07 STAY SET
08 DANGER BOARD
09 150MM DIA GI PIPE 3M LONG
GI CHAIN LINK WIRE FENCE, 2M HEIGHT
10 VERTICAL SUPPORT
INCLINED VERTICAL SUPPORT
2 ROWS LINE WIRE
11 1.5M WIDE X 2.5 M LOCKABLE GATE
12 OUTDOOR CABLE TERMINATION KIT
13 R.S.J. POLE 175 X 85 MM SIZE WITH 11M LONG
14 ISMC CHANNEL
15 BASE PLATE FOR POLE
16 1.0M LIGHTNING SPIKE
17 ANTI-CLIMBING DEVICE
18 25X6 MM GI FLAT
Nomenclature for Four Pole Structure
Item Description
No
01 10KV, 10KA Distribution type LA
02 11KV, 200A GOD Switch with Operating Handle
03 11KV Drop out Fuse
04 11KV Disc insulator string
05 11KV Pin Insulator
06 ACSR DOG CONDUCTOR
07 Anti-Climbing Device
08 DANGER BOARD
09 STAY SET
10 R.S.J. POLE 175 X 85 MM SIZE WITH 11M LONG
11 ISMC CHANNEL
12 ISA Angle 50 x 50 x 6
GI CHAIN LINK WIRE FENCE, 2M HEIGHT
13 VERTICAL SUPPORT
INCLINED VERTICAL SUPPORT
2 ROWS LINE WIRE
14 2.5M (WIDE) x 2M (HEIGHT) Lockable Gate
15 ISMC Channel (75 x 40 x 6 mm)
- Tension Stringing Hardware suitable for Single ACSR DOG
Conductor
- Cable Clamps
- 40mm dia GI straight Length GI conduit Pipe
- 150mm dia GI straight Length GI conduit Pipe
- PG Clamps
- GI Lightning Spike of 25NB (1M long) with test link
arrangement
- Outdoor cable termination kit
- MS Base plate 400 x 400 x 8 Thk
- 25 x3 GI Flat
- Barbed Wire