Professional Documents
Culture Documents
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445 STYLE NUMBER: RCB5306MA
www . quoizel . com
I Ceiling Canopy 1 pc H
J Fixture Loop Assembly 1 pc
I M
K Long Stem 1 pc
L Short Stem 1 pc
M Band A 1 pc
N Band B 1 pc N
O Band C 1 pc
P Finial 1 pc O
P
Bead Kit:
Q A) - Bead String A [15pcs] 1 pc Q
B ) - Bead String B [1 5 pcs]
A)
B)
1 OF 7
PREPARATION STYLE NUMBER: RCB5306MA
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 30 - 45 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (6) 60W B10 candelabra base bulbs .
● Helpful Tools (not included): Wire strippers.
INSTALLATION INSTRUCTIONS
STEP 1:
a. Thread the top end of the Short Stem onto the nipple at
the bottom center of the Band B. Hand tighten until
snug.
b. Place the Band C over the end of the Short Stem and
secure with the Finial. Hand tighten until snug. Please
line up Spokes on Band B and C during assembly. (See
Fig. 2 )
Band B
Short Stem
Band C
Fig. 1 Finial
Front View
Spoke
Bottom View
Band B
Front View
Spoke
Line up
Bottom View Spokes during
Band C assembly
Fig. 2
2 OF 7
INSTALLATION INSTRUCTIONS STYLE NUMBER: RCB5306MA
STEP 2:
a. Thread the end of the Long Stem onto the nipple at the Fig. 1
top center of the Band B. Hand tighten until snug. Fixture Loop Assembly
b. Place the Band A over the top end of the Long Stem and
secure with the Fixture Loop Assembly. Hand tighten Band A
until snug. Please line up Spokes on Band A, B and C
during assembly. (See Fig. 2 )
Long Stem
Band B
Band A
Spoke
Top View
Front View
Front View
Spoke
Bottom View
Band B
Front View
Line up
Spoke Spokes during
assembly
Bottom View
Band C
Fig. 2
3 OF 7
INSTALLATION INSTRUCTIONS STYLE NUMBER: RCB5306MA
STEP 3:
a. Secure the Crossbar onto the Outlet Box with Outlet
Box Screws. Tighten until snug. Outlet Box
Crossbar
Outlet Box
Screw
STEP 4:
a. Thread one Hex Nut onto top end of the Nipple.
b. Place one Lock Washer over the top end of the Nipple
and then thread the Nipple into the center lock hole of
the Crossbar. Lock Washer
c. Using pliers, thread the Hex Nut against the Crossbar Crossbar
and hand-tighten until snug. Hex Nut
Nipple
STEP 5:
a. Thread another Hex Nut onto the end of the Nipple.
b. Place the Lock Washer over the end of the Nipple and
then thread the Canopy Chain Loop onto the end of the
Nipple.
c. Using pliers, thread the Hex Nut against the Canopy Nipple
Chain Loop and hand-tighten until snug.
Hex Nut
Lock Washer
4 OF 7
INSTALLATION INSTRUCTIONS STYLE NUMBER: RCB5306MA
STEP 6:
a. Push the Ceiling Canopy upward over the Outlet Box. Outlet Box
Thread the Canopy Lock Ring onto the Canopy Chain
Loop and tighten until snug to secure the Ceiling
Canopy.
Ceiling Canopy
STEP 7:
a. Adjust the Fixture Chain to your desired length by
removing the links if needed. You may need to use
pliers to open the chain links. If so, put a cloth over the
chain to protect the finish from the pliers. Canopy Chain Loop
b. Attach one end of the Fixture Chain onto the Canopy
Chain Loop and then attach the other end of the Fixture
Chain onto the Fixture Loop on the top of the fixture.
Fixture Chain
Supply Wires
Fixture Loop
5 OF 7
INSTALLATION INSTRUCTIONS STYLE NUMBER: RCB5306MA
STEP 8:
a. Pull the Supply Wires up through the Fixture Chain
alternating links. Push the wires up through the Canopy
Chain Loop into the outlet box. Canopy Chain Loop
Fixture Chain
Supply Wires
STEP 9:
a. Un-thread the Canopy Lock Ring and slide Canopy Outlet Box
Lock Ring and Ceiling Canopy down the Fixture Chain.
b. Push all slack fixture wire through Canopy Chain Loop
into Outlet Box. Trim excess fixture wire leaving a
minimum of 6 in. Hanging out of the Outlet Box.
c. Refer to STEP 10 to connect the wires. Canopy Chain Loop
d. Re-attach the Ceiling Canopy as shown in STEP 6.
Fixture Chain
Ceiling Canopy
6 OF 7
INSTALLATION INSTRUCTIONS STYLE NUMBER: RCB5306MA
STEP 10:
Use Wire Connectors to connect the wires.
WHITE OR RIBBED WHITE OR RIBBED
a. Connect the House Ground Wire to the Fixture Ground
Wire. FROM HOUSE FROM FIXTURE
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side).
c. Connect the House Black (or Red) Wire to the Fixture BLACK (OR RED) WIRE BLACK OR SMOOTH
Supply Wire (Black or Smooth Side).
FROM HOUSE FROM FIXTURE
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the
Outlet Box. GROUND WIRE GROUND WIRE
STEP 11:
a. Attach one end of the Bead String A to the hanger
inside of the Band A. Attach the another end of the
Bead String A to the corresponding hanger in the top
edge of Band B.
b. Attach one end of the Bead String B to the hanger in the
bottom edge of the Band B . Attach the another end of Hanger
the Bead String B to the corresponding hanger at Band
C.
c. Bead String A and B should hang parallel to the center Band A
stem of the fixture. If the strings are not parallel,
slightly rotate Band A or Band C to obtain parallel
alignment.
Bead String A
Band B Hanger
Hanger
Band C
Bead String B
Hanger
STEP 12 :
a. Install correct Bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
7 OF 7