Professional Documents
Culture Documents
4
Company: Page: 1
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
Specifier's comments:
1 Input data
Channel type HAC-C 50/30 400 F
bolt HBC-50/30 8.8F, M12 x 50 mm
Effective embedment depth hef = 94 mm
Channel specification Length: 400 mm, anchor spacing: 175 mm, projection: 25 mm,
width: bch = 50 mm, height: hch = 30 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-17/0336 (2D)
Issued I Valid 5/19/2020 | -
Standard EN 1992-4
Base material uncracked, C35/45, fck,cylinder = 35.0 N/mm2, h = 500 mm
Reinforcement Exist. Reinf.: Widely spaced
No edge reinf. present
Reinf. to control splitting not present
Tolerance data tolerance interval: -350 mm/350 mm
most unfavorable tolerance: -88 mm
2 Overall Result
Design ok! (Maximum utilization: 97%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 2
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 3
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 4
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 298 [mm] ≥ s
Iy = 57781 [mm4]
s = 175 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 94
a1 a2 a3
25 175 175 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 16.534 0.000
a2 14.869 0.000
a3 3.997 0.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 5
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 16.534 17.222 97 ok
Connection anchor-channel 16.534 17.222 97 ok
Channel lip 17.700 25.000 71 ok
Channel bolt 17.700 44.933 40 ok
Flexure channel N/A N/A N/A N/A
Pull-out 16.534 57.820 29 ok
Concrete cone 14.869 16.181 92 ok
Concrete splitting 14.869 24.013 62 ok
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 6
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
17.700 67.400 1.500 44.933
5.1.2 Pull-out failure (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
236
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
16.534 10.5 35.0 86.730 1.500 57.820
5.1.3 Concrete cone (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 7
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
5.1.4 Concrete splitting (Anchor a2, Channel a), concrete cone relevant (EN 1992-4 section 7.4.1.6)
NRk,sp
NaEd ≤ NRd,sp =
gMsp
NRk,sp = N0Rk · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N · y h,sp
N0Rk = min(NRk,p, N0Rk,c) = Min(86.730, 62.544) = N0Rk,c
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,sp N0
i=1
scr,sp = 2 · ccr,sp
0.5
y ch,e,N = (cc ) 1
cr,sp
≤ 1.0
0.5
y ch,c,N,1 = (cc )2,1
cr,sp
≤ 1.0
0.5
y ch,c,N,2 = (cc )2,2
cr,sp
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
( (h ) ) ≤ 2.0
2/3 2/3
y h,sp = (hh )min
≤ max 1.0 ; ef + ccr,sp
hmin
N0Rk [kN] s [mm] scr,sp [mm] y ch,s,N c1 [mm] ccr,sp [mm] y ch,e,N
62.544 175 564 0.558 75 282 0.516
c2,1 [mm] c2,2 [mm] y ch,c,N,1 y ch,c,N,2 y re,N
350 - 1.000 1.000 1.000
h [mm] hmin [mm] y h,sp
500 120 2.000
NaEd [kN] NRk,sp [kN] gMsp NRd,sp [kN]
14.869 36.020 1.500 24.013
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 8
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm N/A N/A N/A N/A
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular N/A N/A N/A N/A
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - N/A N/A N/A N/A
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular N/A N/A N/A N/A
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular N/A N/A N/A N/A
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• A longitudinal reinforcement should be provided along the edge of the member!
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 9
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-50/30 8.8F, M12 x 50 mm
Plate dimensions: 275 mm x 100 mm x 8 mm Bolt length: 50 mm
Profile: - Bolt diameter: 12 mm
Anchorplate design calculated: no Diameter hole: 14 mm
Installation torque: 0.025 kNm
138 138
50
50
1.1 1.2 x
50
50
50 175 50
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.id/content/hilti/A2/ID/en/engineering/software/anchor-design-software.htmlPROFIS Anchor Channel 1.7.4
Company: Page: 10
Specifier: Project:
Address: Fastening point:
Phone | Fax: | Location | Date: 06/10/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan