Professional Documents
Culture Documents
By Adie Dkhaz
1. P channel mosfet
2. N chanel mosfet
each type could substitute as long as same type even with different marking code.
example :
this is P channel
they could be substitute each other even different manufacture and code.
We can see P channel mosfet function on this "GENERAL LAPTOP MAIN POWER " layout link :
There are only 3 pcs P channel there ,2 pcs ADP(adapter) fet's and 1pcs Bat (battery)fet .some
motherboard also may have 1 adp Fet,some replace with diodes to supply every adapter supply need.
I call it "VALW MAIN LINE" .from this line Battery ic and dc/dc power supply ic get VCC to powered each ic and this
main VALW line also distributed adapterVoltage to every N channel Source ,before they got enable trigger to
produced 3V_ALW and 5V_ALW.
(Burada sadece 3 adet P kanallı MOSFET bulunmaktadır. 2 adeti ADP(adaptör) mosfeti ve 1 adeti Batarya mosfeti
olarak bulunmaktadır.
Bazı anakartlar ayrıca 1 adet MOSFET dede sahip olabilir, bazıları her adaptör tedarik ihtiyacını karşılamak için
diyotlarla değiştirilir.
Ben buna "VALW ANA HATTI" diyorum. Bu hattan Battery ic ve dc/dc güç kaynağı ic, VCC'yi her bir ic'ye güç sağlamak
için alır ve bu ana VALW hattı ayrıca 3V_ALW üretmek için tetikleyiciyi etkinleştirmeden önce her N kanal Kaynağına
adaptör Voltajı dağıtır ve 3V_ALW ve 5V_ALW olarak.
P-channel mosfet works drain is a input for nagative supply and source is a output for nagative supply ,and it's gate
on with nagative volt .same way if you want to drive positive supply from p-channel mosfet then souce is input and
drain is output for positive supply .
(P-channel mosfetin drain’i çalışır, drain’e negatif besleme girer ve mosfetin source ayağından negatif besleme çıkar
ve mosfetin gate ayağında negatif voltaj olur. Eğer p kanal mosfet pozitif voltajla sürülürse mosfetin source ayağına
pozitif voltaj girer mosfetin drain ayağından pozitif voltaj çıkar.)
How DC/DC main power supply open/close gate N channel to produce 3V and 5V_ALW and important signal
enable/disable function to activate the DC/DC main supply ic (ISL 6237-RT 8206-TPS 51247) on this link:
How do (RT8223-TPS 51125-TPS 51123)work and signal need on this link :
If you confused ,you should read this before
in this link :
We will also found (SO3) P channel ,(SO8) mean mosfet have 8pin and (SO)3 mean they have 3 pin.And this (SO3)
also have P or N channel type .so be ware if you want to make replacement .just make sure replace it whit same type
(Ayrıca (SO3) P kanal mosfet bulacağız,(SO8) mosfetin 8pin olduğu ve (SO3) 3pin olduğu anlamına gelir3 pin var. Ve
bu (SO3) ayrıca P veya N kanal tipine sahip bir mosfettir. Bu mosfet tipi Arızalı değiştirme yapmak istiyorsun sadece
aynı tipte olanından değişiklik yapabilirsin.)
(Bir pakette 2 mosfet, tek mosfet paketinde basit bir vrm anahtarlama mosfet devresidir, drain ayağı diyot ile katota
bağlı ve source ayağı anot ile bağlı, bir N-Kanal mosfet nasıl tanımlanır.)
(n-kanal mosfetde voltajın drain ayağından akmasını istiyorsanız, gate ayağına + pozitif voltaj
uyguladığınızda,mosfetin drain ayağından source ayağına voltaj akar.N-kanal mosfet'ten source ayağından drain
ayağına voltajın akmasını istiyorsanız, mosfetin gate ayağına – voltaj uygulamalısınız.)
n channel mosfet logic low (vi) that mean mosfet not close circuit between the drain and source ,v_out you got vdd
voltage via resistance . (Hi)
when you apply vi = Hi in N-Channel mosfet ,mean drain to source connected (close circuit) in this case you got v_out
source low you can got at v_out .same way in P-channel but gate work reverse as n-channel mosfet work.
( n kanal mosfet logic low seviyesinde mosfetin drain ve source arası kapalıdır herhangibir akım geçişi olmaz. Direnç
yüksek olur. )