Professional Documents
Culture Documents
Service Manual (Common) : Gn5Un Chassis Segment: SG
Service Manual (Common) : Gn5Un Chassis Segment: SG
Conditions of Use:
(1) Please use this information only for the purpose of performing repair, maintenance and/or configuration services of the Sony products
(hereinafter the “Repair services”) under the service agreement entered into with the Sony group company (hereinafter the “Service
agreement”). Using this information for any purpose other than the purpose described foregoing is forbidden.
(2) Only the Authorized Servicer’s officers, employees or subcontractors (including their officers and employees) whose duties justify a need-to-
know and who have agreed to hold confidential this information (collectively hereinafter the ”Permitted users”) are permitted to access and 9-888-770-01
use this information. To disclose or disseminate to any person other than the Permitted users is forbidden.
(3) Destroy or erase any and all portion of this information promptly in an irrecoverable and secure fashion after achieving the purpose
described in Section (1) above. LCD TV
(4) Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior
written permission of the author.
(Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.)
(5) Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address:
somk-gcs-tissnexim-adm@jp.sony.com
(6) In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information.
Sony EMCS (M) Sdn. Bhd., SVPM
Revision of Information:
This information may be changed or updated at any time without any prior notice. Please confirm that this information is up-to-date before
using it. © 2019.04
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
REVISION HISTORY
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
MODEL LIST
THIS SERVICE MANUAL CONTAINS COMMON INFORMATION FOR BELOW REGIONS AND MODELS:
REGION
ASIA AMERICA EUROPE
MODEL
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
TABLE OF CONTENTS
1. SAFETY NOTES 5
3. TROUBLE SHOOTING 15
5. DIAGRAMS 142
Note: Pictures provided in this manual may have difference from actual sets.
4
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 1
SAFETY NOTES
1-1. Warnings and Caution Whenever a TV Main board is replaced, the correct TV Model and Serial
1) CAUTION :These servicing instructions are for use by qualified service number must be reinserted into memory.
personnel only. This is a MANDATORY procedure that each service center must apply.
2) To reduce the risk of electric shock, do not perform any servicing other than
Please refer to the chapter of ADJUSTMENT in this service manual to
that contained in the operating instructions unless you are qualified to do so.
find out how to set the model number and serial number in service mode.
3) WARNING!! : An isolation transformer should be used during any service
to avoid possible shock hazard, because of live chassis. The chassis of this
receiver is directly connected to the ac power line. 1-2-1. Caution Handling of LCD Panel
The replaceable fuse could be in the neutral of the mains supply. When When repairing the LCD Panel, make sure you are grounded with a wrist
replacing the fuse, the mains shall be disconnected for de-energize the phase band.
conductors. When repairing the LCD Panel on the wall, the panel must be secured
using the 4 mounting holes on the rear cover.
(*Except AC ADAPTOR, Because it does not carry out replacing an internal
1) Do not press the panel or frame edge to avoid the risk of electric
fuse.) shock.
4) CARRYING THE TV : Be sure to follow these guidelines to protect your
2) Do not scratch or press on the panel with any sharp objects.
property and avoid causing serious injury :
• Carry the TV with an adequate number of people; larger size TVs require 3) Do not leave the module in high temperature or in areas of high
two or more people. humidity for an extended period of time.
• Correct hand placement while carrying the TV is very important for 4) Do not expose the LCD panel to direct sunlight.
safety and to avoid damages. 5) Avoid contact with water. It may cause short circuit within the module.
5) SAFETY-RELATED COMPONENT WARNING!! : Components identified
6) Disconnect the AC power when replacing the backlight (CCFL) or
by shading and ! mark on the exploded views, and in the parts list are critical
for safe operation. Replace these components with Sony parts whose part inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms)
numbers appear as shown in this manual or in supplements published by
7) Always clean the LCD panel with a soft cloth material.
Sony. Circuit adjustments that are critical for safe operation are identified in
this manual. Follow these procedures whenever critical components are 8) Use care when handling the wires or connectors of the inverter circuit.
replaced or improper operation is suspected.
Damaging the wires may cause a short circuit.
6) IMPORTANT REMINDER FOR TV MAINBOARD REPLACEMENT :
9) Protect the panel from ESD to avoid damaging the electronic circuit
It is mandatory for service centers to confirm the TV‘s system information after
(C-MOS).
each repair carried out with Mainboard replacement.
5
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
10) During the repair, DO NOT leave the Power On or Burn-in period for *Do not recommend power-on in the conditions which laid face down the
more than 1 hour while the TV is face down on a cloth. Refer Figure 1 . panel, in repair activity. Refer Figure 1 .
*When transporting by hand, do not put stress on the panel and the frame
Figure 1. around the screen.
Refer to the panel handling chapter of each Service manual,
or the "Transporting" information of the Reference Guide of each model
for how to hold it.
2) OLED Screen
•Although the OLED screen is made with high-precision technology and
99.99% or more of the pixels are effective, black dots may appear or
bright points of light (white, red, blue, or green) may appear constantly on
the OLED screen. This is a structural property of the OLED screen and is
not a malfunction.
•Do not push or scratch the front filter, or place objects on top of this TV
set. The image may be uneven or the OLED screen may be damaged.
•The screen and cabinet get warm when this TV set is in use. This is not
1-2-2. Caution for OLED Panel a malfunction.
1) Handling
3) Precautions to Protect the Screen from Damage
When repairing the TV set, be sure you are grounded by using a wrist band.
Image retention
*Do not press on the panel or frame edge to avoid the risk of electric shock. OLED TV’s are susceptible to image retention (burn-in) due to the
*Do not scratch or press on the panel with any sharp objects. characteristics of the materials used. Image retention may occur if images
*Do not leave the module in high temperatures or in areas of high humidity are displayed in the same location on the screen repeatedly or over
for an extended period of time. extended periods of time. This is not a malfunction of the TV. Avoid
displaying images that may cause image retention.
*Do not expose the panel to direct sunlight.
The following are examples of images that may cause image
*Avoid contact with water. It may cause a short circuit within the module. retention:
*Disconnect the AC power when replacing. •Content with black bars either on the top and bottom and/or the left and
*Always clean the panel with a soft cloth material. right sides of the screen. (for example, Letterboxed, 4:3 screen, Standard
*Use care when handling the wires or connectors. Damaging the wires may definition)
cause a short. •Static images such as photos.
•Video games that might have static content in some part of the screen.
*Protect the panel from ESD to avoid damaging the electronic circuit.
•On-screen menus, program guides, channel logos etc.
•Static content from applications.
•On-screen tickers, such as those used for news and headlines.
6
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Panel refresh
Panel refresh will automatically run to adjust the uniformity of the TV
screen after it has been in use for long periods of time.
Panel refresh can also be performed manually and should only be used if 1-3. Caution About the Lithium Battery
image retention is very noticeable or you see the following message: 1) Danger of explosion if battery is incorrectly replaced. Replace only with
[Panel refresh did not finish...] the same or equivalent type.
2) Outer case broken battery should not contact to water.
Caution:
•The Panel refresh function may affect the panel. As a reference, perform 1-4. Safety Check-Out
the Panel refresh only once a year, do not perform it more than once a After correcting the original service problem, perform the following
year as it may affect the usable life of the panel.
safety checks before releasing the set to the customer:-
•Panel refresh takes about one hour to complete.
•A white line may be displayed on the screen during the Panel refresh, 1) Check the area of your repair for unsoldered or poorly soldered
this is not a malfunction of the TV. connections. Check the entire board surface for solder splashes and
•Panel refresh will only work when the room temperature is between 10 bridges.
ºC and 40 ºC. 2) Check the inter board wiring to ensure that no wires are pinched or
contact high-wattage resistors.
Pixel shift 3)Check all control knobs, shields, covers, ground straps and mounting
Automatically moves the image on the screen to prevent image retention. hardware have been replaced. Be absolutely certain you have replaced
all the insulators.
7
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
4) Look for unauthorized replacement parts, particularly transistors that Comply with the following requirement
were installed during a previous repair. Point them out to the customer and Class II equipment (2-pin plug): for each terminal, the worst value of
recommend their replacement. measurement must not exceed AC 350uA peak).
5) Look for parts which, though functioning show obvious signs of Note: including AC adaptor, AC adaptor/DC operated unit combination
deterioration. Point them out to the customer and recommend their
replacement.
Figure 2 – Measuring network
6) Check the line cords for cracks and abrasion. Recommend the for Leakage Current
replacement of any such line cord to the customer.
7) Check the antenna terminals, metal trim, metalized knobs, screws and all
other exposed metal parts for AC leakage. Check leakage test as described
next.
8. For safety reasons, repairing the Power board and/or Inverter board is
prohibited.
8
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
9
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
PRESS
2
1 PULL 1
10
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1 PRESS
1
2
PULL
1
Press the release lock button downward (highlighted in red).
Note: FFC as in image is only for reference purpose. Actual FFC
outlook may vary by each vendor.
2 Pull FFC in straight direction while pressing release lock
button at the same time.
11
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1 1
2
PULL
12
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 2
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the Smart Core Red LED will automatically begin to flash.
The number of times the LED flashes translates to a probable source of the problem.
A definition of the Smart Core Red LED flash indicators is listed in the instruction manual for the user’s knowledge and reference.
If an error symptom cannot be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to
reveal past problems and how often these problems occur.
13
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Tuner Demod Error do not go to Safety Shutdown and do not have RED blinking.
14
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 3
TROUBLESHOOTING
Triage Chart
Before you make the service call…
1. Confirm the symptom from the customer.
CHASSIS: SG 43/49/55/65
2. Select that symptom from the chart.
3. Bring all the boards and cables listed for that symptom.
4. Follow the troubleshooting charts in the technical guides to isolate the board.
5. Chart Colour Code
RED DOT: Most likely defective part
BLUE TRIANGLE: Secondary possible defective part
BLACK TEXT: Board that may correct the symptom
B* Board p l p p p p p l l p p l p
G* Board l p l l l p
H* Board l l
Speaker p l
Wifi Module l
LD* Board l l l p
VBO FFC p p p
Tcon/Source Board p l p p
LCD Panel p l p l p
15
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
LD board
no
1. Check fuse impedance
F1001 / F1002 Fuse F1001 broken
Is < 1ohm?
yes
2. Check impedance no
D1001 to GND Diode D1001 broken
Is > 1kohm?
yes
3. Check MOSFET no
Q1007 MOSFET Q1007 Broken
Is > 1kohm? 4
yes
F1001
F1002
4. Check MOSFET no 1
Q1002
D1001
Q1002 MOSFET Q1002 Broken 2
Is > 1kohm?
yes
no 5
5. Check MOSFET
Q1008 MOSFET Q1008 Broken Q1007
Is > 1kohm?
Q1008
yes
Check B board 3
16
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
17
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
C1024
Input to GND
Impedance check
+12.5V_TCON
F1000
Q1006
F1003
R1003
Input to Output
Impedance check
Output to GND
Impedance check
C1016
18
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
19
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
No No
20
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Adaptor
LD-Board
No Take out adaptor No
2 times Check DC voltage at
and check the output voltage. Change
Q1002
Blinking 18V – 20V? Adaptor
18V – 20V? -ve
(Refer Figure 1)
*Typical: 19.5V
*Typical: 19.5V
Yes +ve
Yes
Ensure that
Change LD- Change LD-
+ve probe is
board Board
touching the
needle.
21
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Q1002
19.5V
22
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
3x blinking
B-board Audio Error pin
short to GND Disconnect power supply
and check Audio Error pin
Change B-board
No 3x blinking No 3x blinking
DONE
23
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
#Audio IC (IC3101) problem
3x blinking
No 3x blinking
Check have any burn mark on Audio IC,
If have burn mark, replace the NG Audio IC
3x blinking
Change B-board
DONE
24
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Board
B Board (Checking Point)
PWB BB9 (CHL/SG) - Audio Amp circuit
(A side)
F3101
Purpose :
Checking F3102
Audio Error
pin not short
to GND
Checking fuse
condition IC3101
CN3109
Change Audio
IC if need
25
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
TV boot up normally?
Yes
No
No
Suspected LD board /G
No Check PANEL_PWR Yes Check +12.5V_TCON No Board side issue.
Check voltage at
+12.5V_TCON 3.00V-3.33V? 10.8V-13.2V? Replace PSU unit board
10.8V-13.2V
Yes
End
26
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
30pin PSU/LD
Connector
SoC
51pin LVDS Connector
PANEL_PWR
+12.5V_TCON
27
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
NO TV set is OK now
NG symptom:
Is 10.8 – 13.2V available?
START LD board/ G board
no +12.5V_TCON supply
YES
Replace B-Board
Reinsert LVDS 51pin Flat
Flexible Cable (FFC) at B-Board and
Panel Side. Make sure FFC is taped
properly. No
5 Times Blinking happen? TV set is OK now
NG Symptom:
YES B-Board Issue NG
No TV set is OK now
5 Times Blinking happen? NG Symptom:
Incorrect FFC Insertion Replace
YES O-Cell* or Panel Module*
No TV set is OK now
5 Times Blinking happen? NG Symptom:
LVDS Cable NG * O-Cell or Panel
YES END Module replacement
depends on service
capabilities
28
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
30pin PSU/LD
Connector
SoC
51pin LVDS Connector
+12.5V_TCON
29
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
30
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
CN2000
R3003
LEDVCC1 LEDVCC2
F2004
F2005
31
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
No Picture
NG NG
OK
Check Smart Core Replace
Got Any Abnormal Replace Replace
LED Indication the V by One FFC
Display? No the main Board LD/G Board
No (5x Blinking) Harness
Yes Yes OK OK
LCD Panel
(T-CON) NG
Ext. Video Input -
No Picture
HDMI - No Picture
Tuner - No Picture
32
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
NG
Check RF source cable Change RF cable and antenna NO
and antenna, OK? YES
OK
33
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
(3.3V) (1.8V)
CL1000 CL1000
(3.3V)
(1.8V)
CL1001
(12V)
CL1006
F1000
F1001
Detail
F1001
F1000
CL1006
(12V)
34
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Notes:
- Parts for IFOUTN1 line: FB1000,C1005
- Parts for IFOUTP1 line: R1030, FB1001,C1006
- Parts for IFAGC1 line: C1014, R1010
Analog Tuning For LA-ISDB,
PA_ISDB & -Parts for M_SCL line: C1004,R1049
LA-T2 -Parts for M_SDA line: C1003,R1048
For Other
destination Confirm Antenna or Cable connection
OK OK
Not Noisy OK
Problem OK
Please re- Done (End)
OK upgrade NG solved?
Firmware (PKG), NG
Check again
Picture quality?
Change Tuner Module
(Please refer page Assemble and Dissemble Tuner Module)
OK
Done (End) Problem solved?
NG
Change B-board
35
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
BB9 board
(A side)
C1006 FB1001
(IFOUTN1) R1030
FB1000
C1005
(IFOUTP1)
R1030 C1005 FB1000
FB1001
C1006
36
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
BB9 board
(A side)
(IFAGC1)
C1014
R1010
C1014
R1010
37
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
BB9 board
(A side)
(M-SCL)
C1004 R1049
C1004
R1049
(M-SDA)
C1003
R1048 C1003
R1048
38
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.3 FOR DIGITAL TUNING 1: For TW-DVB , AM-ATSC, LA-ISDB , EU-DVB only
Notes:
- Parts for IFOUTN1 line: FB1000,C1005
- Parts for IFOUTP1 line: R1030, FB1001,C1006
Digital Tuning 1 - Parts for IFAGC1 line: C1014, R1010
-Parts for M_SCL line: C1004,R1049
-Parts for M_SDA line: C1003,R1048
No sound
If UEC = 0 Check IC 5000(SoC)
Confirm UEC of digital RF by Service mode
(Change B-board)
If UEC > 0
OK
Problem solved?
NG
Done (End)
Change B-board
39
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.3 FOR DIGITAL TUNING 1: For TW-DVB , AM-ATSC, LA-ISDB , EU-DVB only
BB9 board
(A side)
C1006 FB1001
(IFOUTN1) R1030
FB1000
C1005
(IFOUTP1)
R1030 C1005 FB1000
FB1001
C1006
40
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.3 FOR DIGITAL TUNING 1: For TW-DVB , AM-ATSC, LA-ISDB , EU-DVB only
BB9 board
(A side)
(IFAGC1)
C1014
R1010
C1014
R1010
41
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.3 FOR DIGITAL TUNING 1: For TW-DVB , AM-ATSC, LA-ISDB , EU-DVB only
BB9 board
(A side)
(M-SCL)
C1004 R1049
C1004
R1049
(M-SDA)
C1003
R1048 C1003
R1048
42
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.4 FOR DIGITAL TUNING 2: For EU-T2S2, PA-T2, LA-T2 ,HK-DTMB & PA-ISDB only.
Notes:
Digital Tuning 2 -Parts for M_SCL line: C1004,R1049
-Parts for M_SDA line: C1003,R1048
For LA-T2 For EU-T2S2 -Parts for DEMOD_TSCLK line: R1020
For EU-T2,
Confirm ANT or Cable connection PA-T2, PA-ISDB Confirm ANT or Satellite connection - Parts for DEMOD_TSDATA line: R1019
and HK-DTMB
No sound
If UEC = 0
NG
Done (End)
Change B-board
43
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.4 FOR DIGITAL TUNING 2: For EU-T2S2, PA-T2, LA-T2 ,HK-DTMB & PA-ISDB only.
BB9 board
(A side)
(M-SCL)
C1004 R1049
C1004
R1049
(M-SDA)
C1003
R1048 C1003
R1048
44
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.4 FOR DIGITAL TUNING 2: For EU-T2S2, PA-T2, LA-T2 ,HK-DTMB & PA-ISDB only.
BB9 board
(A side)
(DEMOD_TSCLK)
R1020
(DEMOD_TSDATA0)
R1019
R1020
R1019
45
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
If TV unable to output audible tone /wakeup during standby after received EWBS signal– General Checking
Start
Connection Failed
OK
OK
Does any
NG: Tuner power is OFF EWBS Feature is
RF signal stored Not Enable
from RF Antenna? during standby
OK
NG: Cannot locked
Does Tuning RF any signals Refer to
Antenna 2.6.3.1 No Picture Tuner
Trouble shooting
OK? flow
OK
END
46
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
BB9 board
(A side)
(EWBS-
Tuner_wakeup line)
R5066
R5066
47
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.6 – NO SOUND
NO
Only RF tuner input?
YES
48
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Do a Factory Setting
*2 Confirm with OSD on bottom panel, if
playback not support.
OFF *1 Confirm USB Auto Please refer to IM for detail supported USB
Start is ON or OFF
format.
Change to ON
ON
Detection OK NG Check 5V at No 5V
and C7012 (USB
Picture and Sound OK port1)
Have 5V but No detection
*2 Confirm USB NG
OK
file format
Sound NG
Sound OK Audio IC (IC3101) problem
OK
Change B-Board
END
49
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Do a Factory Setting
*2 Confirm with OSD on bottom panel, if
playback not support.
OFF *1 Confirm USB Auto Please refer to IM for detail supported USB
Start is ON or OFF
format.
Change to ON
ON
Detection OK NG Check 5V at No 5V
and C7029 (USB
Picture and Sound OK port2)
Have 5V but No detection
*2 Confirm USB NG
OK
file format
Sound NG
Sound OK Audio IC (IC3101) problem
OK
Change B-Board
END
50
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Detection OK NG Check 5V at No 5V
and C7037 (USB
Picture and Sound OK port3)
Have 5V but No detection
*2 Confirm USB NG
OK file format
Sound NG
Sound OK Audio IC (IC3101) problem
OK
Change B-Board
END
51
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Board
Board PWB (A side) Detail
Name
Have 5V?
C7012
BB9
C7037
52
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Board
Board PWB (A side) Detail
Name
Have 5V?
C7029
BB9
53
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.12 Ethernet
2.6.12 Ethernet – No Connect – General Checking
TV turn ON condition:
START
Failed
OK Check if any abnormal Yes
Check if the Ethernet or broken point on Connector (J7000) and parts NG
cable is good Ethernet Connector and parts Change B Board
(J7000/L7000/RB7000/C7002)
NG
No
Change a good cable
Yes T7000 or T7001 or Main IC
Check if TV has MAC Address
(IC5000) NG
Set-up Network setup
Change B Board
Failed
Check TV has connection OK 54
Set-up Network setup
Failed
OK
END
54
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.12 Ethernet
2.6.12 Ethernet – No Connect – Checking Point
Ethernet (B-board Checking) – Checking parts broken or knock off
Board
Board PWB (A side) Detail
Name
C7002
BB9
J7000
55
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.13 CI Slot
2.6.13 CI Slot – Cannot Play / No picture / No Sound – General Checking Remarks:
*1 Important: Please use a known
TV turn ON condition: Good CICAM for testing
Valid key No
Check service menu for
CI+ Credentials CI+ Key
Check any pin on No
Invalid key CI Slot is bend or
broken.
Insert CICAM and Yes
Yes
Check CI 5V
at PIN 17/18/51/52
Invalid Key *2 Insert CICAM and Yes
Change B Board Connector NG No Check CI Detection
Change B Board at Pin 36/67
No Yes
IC7003 NG *3 Check Resistor
Change B Board Part mounting
END
56
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.13 CI Slot
2.6.13 CI Slot – Cannot Play / No picture / No Sound – Checking Point
CI Slot (B-board Checking) – Checking 5V Points [1/3]
Board
Board PWB (A side) Detail
Name
CI 5V at PIN
17/18/51/52
BB9
57
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.13 CI Slot
2.6.13 CI Slot – Cannot Play / No picture / No Sound – Checking Point
CI Slot (B-board Checking) – Checking CI Detection Pin Points [2/3]
Board
Board PWB (A side) Detail
Name
BB9
Remark:
Both CI Detection Pin should be 3.3V before CICAM insert and 0v when CICAM inserted.
58
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.13 CI Slot
2.6.13 CI Slot – Cannot Play / No picture / No Sound – Checking Point
CI Slot (B-board Checking) – Checking Resistor Part Mounting Points [3/3]
Board
Board PWB (A side) Detail
Name
5
2
BB9
1 3 6 4
59
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
[NG] No picture
Factory reset [OK] Picture recovered TV
HDMI source & re-verify END
setting problem
[NG] No picture
[NG] Connector abnormal HDMI Connector Broken. [OK] Picture recovered
Physical appearance check
On HDMI connector Replace & Re-verify
[NG] No picture
[OK] Appearance OK
Check voltage of +5V Power
HDMI1: CN4001 – Pin 18 [NG] V5V ≠ 4.8 ~ 5.3V Go to
HDMI2: CN4002 – Pin 18 “+5V Power Failure Analysis“
HDMI3: CN4000 – Pin 18 Page
[OK] V5V = 4.8 ~ 5.3V
Check voltage of HPD
HDMI1: CN4001 – Pin 19 [NG] VHPD ≠ 2.4 ~ 5.3V Go to
HDMI2: CN4002 – Pin 19 “HPD Power Failure Analysis“
HDMI3: CN4000 – Pin 19 Page
[OK] VHPD = 2.4 ~ 5.3V
60
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
END
61
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
[OK] Compatible
Verify HDMI Source
device compatibilities for
HDCP version 2.2
[OK] Compatible
[NG] No picture
Replace B-Board and Re-verify
END
Escalate this issue to
R&D team
62
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
+5V Power
Failure Analysis
END
63
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
+5V Power
Failure Analysis
[NG] Impedance ≠ 22 Ω
Check impedance of [OK] Picture recovered
Replace Broken Resistor
Resistor during AC OFF and Re-verify
HDMI2: R4044
[NG] No picture
[OK] Impedance ≈ 22 Ω
END
64
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
HPD
Failure Analysis
[OK] All part as below
R4021, R4022 ≈ 4.7KΩ
R4015,R4016, R4018, R4019 ≈ 1KΩ Check HPD GPIO Line
Check impedance of [OK] Impedance ≈ 100kΩ ±5%
impedance to Ground
Resistor during AC OFF
during AC OFF
HDMI1: R4016, R4019 and R4022
HDMI1: R4019*
HDMI3: R4015, R4018 and R4021
HDMI3: R4018*
[NG] Any of the part as below
R4021, R4022≠ 4.7KΩ [NG] Impedance ≠ 100kΩ ±5%
R4015,R4016, R4018, R4019≠ 1KΩ
Internal Main IC (SoC)
Replace Broken [NG] No Picture Broken (IC5000)
Resistor and Re-verify Go to
“I2C Failure Analysis“
[OK] Picture recovered Replace B-Board Page
and Re-Verify
END
65
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
HPD
Failure Analysis
66
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
HDMI2
R4019*
Only measure this point
reference to GND
R4043*
Only measure this point
reference to GND
HDMI3
HDMI1
R4018*
Only measure this point
reference to GND
67
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
I2C
Failure Analysis
[OK] HDMI1 Impedance ≈ 140kΩ ±5%
Check I2C GPIO Line [OK] HDMI2 Impedance Open (High Z)
Check impedance of impedance to Ground
Resistor during AC OFF [OK] Impedance≈ 47kΩ [OK] HDMI3 Impedance ≈ 140kΩ ±5%
during AC OFF
HDMI1: RB4001 HDMI1: CN4001 – Pin15&16
HDMI2: RB4002 HDMI2: CN4002 – Pin15&16
HDMI3: RB4000 HDMI3: CN4000 – Pin15&16
[NG] Impedance ≠ 47kΩ [NG] HDMI1 Impedance ≠ 140kΩ ±5%
[NG] HDMI2 Impedance not Open (High z)
[NG] HDMI3 Impedance ≠ 140kΩ ±5%
68
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
TMDS
Failure Analysis
END
69
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Replace B-Board
END
And Re-verify
70
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Pin 1 Zoom 2 :
L4004 HDMI2
CN4002
L4005
Zoom 4
Zoom 2 R4005
Zoom 1
Zoom 3
RB4002 VR4011
R4007 R4044
RB4001
R4022 R4025
R4004
R4019 Pin 19
R4008
R4016 R4043
L4002
VR4010
Pin 1
Pin 19
L4003
CN4001
Zoom 1 :
HDMI1
71
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
L4001 L4000
Pin
1
R4036 Zoom 3 :
HDMI3
Zoom 4
R4003
RB4000
VR4009
R4006
Zoom 3
R4024
R4021
CN4000
RB4003 RB4004 R4018
Pin
R4031 R4015 19
RB4006
RB4005
RB4008
Zoom 4
RB4007
72
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
73
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.15 WIFI
2.6.15 WIFI – Cannot search device / Connection Failed – General Checking
Start
Connection Failed
Check Built-In WiFi NG: Built-In WiFi Off WiFi Feature is NG: Signal Strength Low AP Device
UI Not Enable Check AP/Device Problem
(Change AP/Device)
OK OK
OK
NG: DC Voltage is
Check TP-VCC not 5V WiFi Module
DNUR-SY3 DNUR-SY3 Broken
(Change WiFi Module)
OK
74
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.15 WIFI
2.6.15 WIFI – Cannot search device / Connection Failed – Checking Point
IC6016
IC6016
75
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2.6.15 WIFI
2.6.15 WIFI – Cannot search device / Connection Failed – Checking Point
76
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Video
No Picture
Check if input on OSD Yes Check R2021 voltage. Yes J2002 Connectivity
is GREY OUT? Is it 3.3V? Problem.
(not selectable)
No No
Check all parts
Check waveform No Yes
at CVBS0P signal path.
before C2006.
[VR2000,R2004,
Is it Vpp : 1V?
C2000, R2017]
Yes No
J2002 Connector
Parts Broken.
Problem.
(Change Part)
(Change connector)
IC5000 Problem.
(Refer IC troubleshooting
manual)
77
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
J2002
BB9 (WW)
C2006 Details C2006
R2017
R2017
78
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
No Picture or
CHL UC Abnormal Picture
Reinsert Mini Plug
Video Adaptor
until hear Mini Plug Video
“click” sound Adaptor
Video Component
No Picture No Picture
IC5000 Problem
Check waveform Check Vpp waveform IC5000 Problem
No (Refer IC
before C2006? at 1) C2003 for Y : 1V? No (Refer IC
troubleshooting
Is it Vpp : 1V? 2) C2008 for Pb :0.7V? troubleshooting
manual)
3) C2009 for Pr :0.7V? manual)
Yes
1) Y : 1V Yes 2) Pb : 0.7V 3) Pr : 0.7V
79
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
J2000
BB9 (UC)
C2003 C2008 C2009
C2006
C2008
C2009 Details
R2014 C2003 C2006
R2017
R2018
R2019
R2014 R2019
R2018 R2017
80
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
81
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1.05V LDO
43”
49”
3.3V
19.5V DDC 1.5V DDC
LD
1.05V DDC
55” 1.0V
65” DDC
5V DDC
(WIFI)
G-Board
12.7V
5.0V 1.8V LDO
DDC
1.8V DDC
(TUNER)
82
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Check C6134,
Check C6093 Voltage. no C6050 is it no LDO: +1.05V_M3_xx check
DDC: +3.3V_DDC_OUT check
Is the voltage 3.3V? 1.05V?
yes yes
Check C6042 Voltage. no DDC: +1.5V_DDR check Check C6058 no DDC: +1.8V_TU check
Is the voltage 1.5V? is it 1.8V?
yes yes
yes yes
Check 3.3V_MAIN
Check C6141 Voltage. C6130 Voltage. no SW: +3.3V_MAIN check
no
DDC: +5V_WIFI check
Is the voltage 5V? Is the voltage 3.3V?
yes
yes
83
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Check fuse no
F6005 / F6008 Change F6008
Is fuse OK?
yes
yes
Check EN signal no
R6088 voltage G-Board/LD-Board
Is voltage >2.9V?
yes
Check Vcc no
C6082 voltage Change IC6010
Is voltage >5.3V?
84
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
no
Is IC6004 mounted?
yes
Check Enable no
IC6019 #pin1 Change IC6019
Is voltage >2.5V?
yes
Change DDCON
IC6004
85
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Check VG signal no
Q6007 #pin1 Change Q6007
Is voltage > 4.9V?
yes
no
Other Issue
86
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Check fuse no
F6004 / F6007 Change F6004
Is fuse OK?
Check EN signal no
R6073 voltage G-Board/LD-Board
Is voltage >2.5V?
yes
Check Vcc no
C6062 voltage Change IC6009
Is voltage >5V?
yes
SG 55”/65”=G-Board model (PSU)
END SG 43”/49”=LD-Board model (ADP)
87
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Check fuse no
F6006 / F6009 Change F6006
Is fuse OK?
Check EN signal no
R6114 voltage MTK IC damage
Is voltage >1.9V?
yes
Check Vcc no
C6102 voltage Change IC6017
Is voltage >5.3V?
yes
SG 55”/65”=G-Board model (PSU)
END SG 43”/49”=LD-Board model (ADP)
88
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
+1.05V_M3_STBY +1.8V_EMMC
START START
yes yes
Check input no Check input no
C6049 voltage DDC: 3.3V_DDC_OUT check C6124 voltage DDC: 3.3V Switching check
Is voltage >3.0V? Is voltage >3.0V?
yes yes
Check EN signal no Check EN signal no
IC6005 #pin3 DDC: 3.3V_DDC_OUT check IC6018 #pin3 DDC:3.3V Switching check
Is voltage >3.0V? Is voltage >3.0V?
yes yes
89
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
yes yes
MTK IC damage
Change IC6007
90
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Check voltage
no
C6130 DDC: 3.3V switching check
Is voltage >3.0V?
yes
Check EN signal
no
R6120 DDC: 3.3V switching check
Is voltage >3.0V?
yes
Change IC6014
91
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Change IC6016
92
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
Check VG signal no
Q6009 #pin1 Change Q6009
Is voltage > 3.0V?
yes
Check VB signal yes
Q6008 #pin2 Change Q6008
Is voltage > 1.9V?
no
Other Issue
93
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
IC6004
IC6010
IC6009
Q6008
Q6009 IC6017
Q6006
Q6007
IC6014
IC600
IC6018 5
IC6007
IC6016
94
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
C6093
C6066
F6005
C6153 IC6009
C6086 C6042
IC6004
C6040
IC6010
F6008
C6072
95
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
R6114
C6136
C6055
C6141 F6009
IC6017
R6162
IC6007
IC6016 F6006
C6058
C6106
C6146
R6167
96
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
C6130
R6120
Q6008 Q6006 C6134
#PIN2 (VB)
#PIN2 (VB)
97
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
C6049
98
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
12 GVDD 5V 5V - 26 A_SEL 0V 0V -
99
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
19.5V/12.7V F3101
B board
F3102
7, 10, 26
Zoom 15 14 13 12 11 9
8
16
6
17 5
18 4
IC3101
19 3
20 2
1
21
28
27
22 23 24 25
100
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Video/Component Refer
No Sound? “Analog Audio Input No Sound”
Analog RF Refer
No Sound? “Analog RF No Sound”
101
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
No Sound
Do a Factory Setting & Sound
set to desire channel with sound
No Sound
J3501 Pin4 ≠ 0V Sound
Headphone No Insert,
Replace J3501
Check J3501 Pin4 Voltage
No Sound
No connectivity for
Check Speaker Harness speaker harness Change Speaker Sound
Connectivity Harness
No Sound No Sound
No Sound No Sound
No connectivity of
(F3101 or F3102) Sound
Check fuse connectivity (F3101 or F3102) broken,
at (F3101 or F3102) Replace (F3101 or F3102)
No Sound & (F3101 or F3102) OK
No Sound & (F3101 or F3102) OK
Any I2S line
Check I2S lines short to GND? short to GND Main IC (IC5000) or
(BCLK, LRCLK, SDATA0) Audio IC (IC3101) problem
No Sound & I2S lines no short to GND
Change B-board
DONE
102
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
B board
IC5000
IC5000
LRCLK
SDATA0
BCLK
103
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
No Sound
Do a Factory Setting & Sound
set to desire channel with sound
No Sound
Check AV Setup, Sound
Headphone is selected
No Sound
Sound
Use another Headphone Headphone problem
No Sound, Headphone OK
No Sound, Headphone OK,
Headphone Inserted, J3501 Pin4 is 0V Sound
Replace J3501
Check J3501 Pin4 Voltage
No Sound, Headphone OK,
J3501 Pin4 is 3.3V
No Sound, Headphone OK,
HP Amp IC (IC3501) or J3501 Pin4 is 3.3V
Main IC (IC5000) problem
Change B-board
DONE
104
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
B board
IC5000
Pin4
IC3501
J3501
105
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
No Sound
Do a Factory Setting & Sound
set to desire channel with sound
No Sound
Check correct Sound
Source mode is selected
No Sound
RCA cable Sound
Use another RCA cable
problem
No Sound & RCA cable OK
Check Analog Input Source Sound
Analog Input Source problem
& use another input source
No Sound & Analog Input Source OK
No Sound
Check Speaker & Headphone
Using other input mode
Sound & Speaker / Headphone OK
Refer
Sound Audio Problem
Main IC (IC5000) problem
Speaker No Sound
& HP No Sound
Change B-board
DONE
106
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
No Sound
Do a Factory Setting & Sound
complete the RF tuning
No Sound
No Sound
OK
No Sound
OK
Raster sound, OK? NG
(applicable for PAA, PAD, CHN, PH, Refer “Main Speaker No Sound”
for other region skip this)
OK
OK
UI setting, OK? NG Sound
Correct UI setting
(TV System, AFT, Audio Filter)
UI OK, No Sound
No Sound
OK B-board
Change
DONE
107
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
No Sound
Do a Factory Setting & Sound
set to desire HDMI source with sound
No Sound
NG Sound
HDMI cable, OK? Change HDMI cable
No Sound
OK
NG Sound
HDMI source, OK? Change HDMI source/channel
No Sound
OK
NG
HDMI Playback, OK? Refer “HDMI Problem”
OK
DONE
108
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
109
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Pin 1
R4036
HDMI 2 Zoom
(CN4002)
HDMI 3
(CN4000)
Pin 19
110
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
START
No Sound
OK
NG Sound
UI setting, OK?
Correct UI setting
(Music, Video)
UI OK
No Sound
*Confirm with OSD on bottom panel, Change B-board
if playback not support.
*Please refer to IM for detail supported USB
audio format.
DONE
111
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Please refer to “2.6.7 USB Port 1 – No Detection / Cannot Play / No Picture / No Sound”.
Please refer to “2.6.8 USB Port 2 – No Detection / Cannot Play / No Picture / No Sound”.
112
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
NG
NG
OK
Change switch module Switch module issue
NG
NG
Resistor value Check resistor value on B-
Parts issue
board
[BB9]
R9507 : 0 [ohm] OK In case that power key error
R5063 : 100 [ohm]
R9512 : 4.7k [ohm]
NG
Check resistor value on B-
board
Resistor value
In case that buttons error except power key
[BB9] OK
R3023: 100 [ohm]
Main device issue
R9509: 12k [ohm]
Change B-board
R9510: 33k [ohm]
113
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Check harness OK
Harness connection
connection between B-
issue
board and H-board
NG
Change harness between OK
B-board to H-board harness
B-board to H-board
issue
harness
NG
OK
Change H-board H-board issue
NG
OK
Check resistor value on
Parts issue
B-board
Resistor value
[BB9] NG
R5022: 100 [ohm] Change B-board
Main device issue
114
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 4
SERVICE ADJUSTMENT
When finished the operation of service mode , please AC Plug OFF/ON the TV set
*If you don’t do AC plug OFF/ON, remain the Service Mode App and user can see the Service Mode after RC ON.
4 Service Mode
Status
StatusInformation
Information >>
Self Diagnosis History >>
2 Wide Band Tuning >>
Panel Selection
<[ 5_NS7S400HND0101_0 ]>
Status 1st Tu Infor >>
LVDS Spectrum (%) <[ 30 ]>
Update CI+ Credentials >>
SERIAL NUMBER EDIT
1 Model Number Setting
TEST RESET <[ Off ]>
UART Selection <[ No Log ]>
HDD Performance Check >>
AAA >>
Tu Data for Serv >>
SDB Service Menu >>
3 Panel/PQ >>
General Setting <[ Off ]>
Default date for HDD recording <[ Off ]>
Tuner Detection >>
LVDS Driver Strength <[ 4 ]>
ATMOS CEC DISABLE <[ 0 ]>
CEC FORCE LA=0 <[ 0 ]> *Service menu disappears, but the app
Read HDMI EDID >> is working in the background,
Option bit >> If you don’t do AC plug OFF/ON,
remain the Service Mode App and User
[< / >] Set [Home] Exit can see the Service Mode after RC ON
(Supplementary 115
information) SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Cursor (Left/Right/Up/Down) Change focus item, Change option of focus item, Return to previous page
(Supplementary 116
information) SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Main Micro
SW Version:
vX.XXX
NVM Version:
TD1.000
Boot Version:
vX.XX
Panel ID Version:
PA0.XXX
Wi-Fi Version:
JEDI.L0.MP1.mt7603u.vX.X
PQ Version:
PQ0.XXX
AQ Version:
AQ0.XXXX
117
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
4.5 How to enter Self Check Go to Self diagnosis history through Service Mode
1) In Service Mode, select “Self diagnosis history”, press “Enter” or “” button to enter Self Check.
Service Mode
Status Information >>
Self diagnosis history >>
Panel Selection <[ 1_IS6S320CNO0101 ]>
STATUS 1st Tu Infor >>
LVDS Spectrum (%) <[ 30 ]>
SERIAL NUMBER EDIT 123475
Model Number Setting BCD-9876543
TEST RESET <[ Off ]>
UART Selection <[ Factory ]>
HDD Performance Check >>
AAA >>
Tu Data for Serv >>
[Home] Exit
118
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
[Home] Exit
00033 00006 00033
Error history clear
<8> -> <0>
Panel operation time clear
<7> -> <0>
Total Operation Time [h] – Boot Count – Panel Operation Time [h]
(max 65535) (max 65535) (max 65535)
119
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
120
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Please refer to the following Table to confirm if Panel Selection and LVDS Spectrum(%) values are correct.
121
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2) Press Up or Down button to change number and “” button to edit next number
122
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
123
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Step:
i) Enter Self diagnosis history >Self Check
ii) Press <6> <0>
* Warning please don’t reset the serial number unnecessarily.
Always check the input data is correct before rewrite. When data is
clear, it affect both Model number & serial number.
124
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2) Press Up or Down button to select character and “” to edit next character
125
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
126
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Step:
i) Enter Self diagnosis history >Self Check
ii) Press <6> <0>
* Warning please don’t reset the serial number unnecessarily.
Always check the input data is correct before rewrite. When data is
clear, it affect both Model number & serial number.
127
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
128
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Remark#1
Whenever these R/G/B Gain & R/G/B Offset values have been set, these values will be applied common to all
Picture Mode (Vivid, Standard, Custom) & Color Temperature (Cool, Neutral, Warm, Expert1, Expert2).
After operation is completed, just exit the Service Menu page.
Remark#2
To set these R/G/B Gain & R/G/B Offset values to default, kindly toggle each component to “512”.
129
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
130
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
2) (a) Select “WB/Gamma data transf” by pressing “↑” or “↓” on remote commander.
(b) To change the items, press “←” or “→” on remote commander and press “Enter” button.
select “1. T-con to SoC” for each items.
131
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Remark#1
Toggle ”→” to select “ON” or Toggle “←” to select “OFF”
Exit Service Mode by pressing “Return” on Remote
Commander.
Remark#2
Ensure that there is no Cable (RF, HDMI, etc.) connected to
the TV
132
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Remark#3
Perform Test Reset on TV after turning “OFF” Aging Mode
Test Reset
Press <Power> tact key on TV with keep pressing <Up> key on RC
-> Then, displays “RESET” on Screen.
133
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
134
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
3) Go to “Tuner Check” and press “” or “” to enter selection “On” or “Off” *.
• “Tuner Check” = On , to execute “Tuner Check” and update “Tuner Status”
value.
• “Tuner Check” = Off (default value). Always set “Tuner Check” to “Off” after
confirm “Tuner Status” value
**”Tuner Status” will only update if “Tuner Check”=‘On’ and AC Off/On is already
performed.
6) “Mounted Tuner Type” is the type of tuner module that is currently inserted to TV
135
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1) Go to “ATMOS CEC DISABLE” and Press “” or “” button to select ‘0’ or ‘A’
Remarks :
1) This data is not changed by software update or
AC off/on, only change from service menu.
2) Need to turn AC off/on after change setting in
order algorithm to take effect.
2) After select the option that you wish, press “Home” to confirm the selection.
Option Execution Effect
The TV checks whether
HDMI1(ARC) is connected to an
0 (default) amplifier that support ARC &
Atmos or not, and sets either
Atmos EDID/ Non Atmos EDID.
The TV skip Atmos checking
when HDMI1(ARC) is connected
A to an amplifier that support ARC
and set Atmos EDID even when
amplifier doesn’t support Atmos.
136
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1) Go to “CEC FORCE LA=0” and Press “” or “” button to select ‘0’ or ‘A’
CEC_Force_LA=0
Data : [0/A] Default : 0
Purpose : To avoid CEC conflict for Non CEC
compliant device.
Usage: When market claim happen such as Bravia
Sync malfunction or no ARC sound happen, due to
HDMI device make CEC conflict, then Service side is
required to change this service register from “0” to
"A"
Remarks :
1) This data is not changed by software update or
AC off/on, only change from service menu.
2) Need to turn AC off/on after change setting in
order algorithm to take effect.
2) After select the option that you wish, press “Home” to confirm the selection.
Option Execution Effect
137
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1) Go to “Read HDMI EDID” and Press “” button to enter “Read HDMI EDID”
display
Read_HDMI_EDID
Purpose : To read HDMI EDID data without using any external equipment.
Usage:
1) When market claim happen or product already ship out, Service side and
Production side can easily read the EDID without disassembling rear cover.
2) To simplify EDID checking.
138
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
Option Purpose
To select the Shipping region of the
Shipping
Set. Please don’t change this setting
region
unless for service board replacement .
2) Select the option available “Shipping region” or “Tuner ID” by pressing “” or “”. Then press “>” or “ Enter”.
139
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1) Go to “Shipping Region” and Press “” or “” button to select 2) Press enter to confirm Region. Pop-up will display
*region. (Region availability depends on SW pkg)
140
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
1) In Tuner ID service mode, Press “” to select “Shipping Region” and 2) Press enter to confirm Tuner ID. Pop-up will display
Press “” or “” button to select *Tuner ID. (availability depends
on SW pkg)
141
SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 5
DIAGRAMS
Some control lines are left out.
5.1 SG 43/49/55/65 Block Diagram
FY19 (SG)-4K (BB9 PWB for COL, BR, PAA, PAD, LA, PH, CH, TW)
(Supplementary 142
information) SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 5
DIAGRAMS
Some control lines are left out.
5.1 SG 43/49/55/65 Block Diagram
FY19 (SG)-4K (BB9 PWB for EU)
(Supplementary 143
information) SYS SET
2019/05/01 02:23:15 (GMT+09:00)
SECTION 5
DIAGRAMS
Some control lines are left out.
5.1 SG 43/49/55/65 Block Diagram
FY19 (SG)-4K (BB9 PWB for UC)
(Supplementary 144
information) SYS SET
SG 43’/49’
2019/05/01 02:23:15 (GMT+09:00)
Switch Module To Main Board To Source Board From T-CON Board Source
CN203 BAX_F
BB9 Main Board GND 1 51 GND
T-con
3M-P HUS_GND 1 7 #30 VBTX7P 2 50 RxP7 Board
HUS_KEY_AD 2 9 #30 VBTX7N 3 49 RxN7
Board
HUS_POWER_KEY 3 8 #30 GND 4 48 GND
P/N: 1-822-693-11 VBTX6P 5 47 RxP6 PANEL FFC pin FFC 60pin PANEL FFC 60pin
JAM SZ15-03WLR VBTX6N 6 46 RxN6
GND 7 45 GND
VBTX5P 8 44 RxP5
Main Harness VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4 HIROSE TF06L-60S-0.5SH HIROSE TF06L-60S-0.5SH
VBTX4N 12 40 RxN4 LSM GF05G-60S-MB-E2000 LSM GF05G-60S-MB-E2000
1 1 5V_MAIN GND 13 39 GND YEONHO 05002HR-H60Y YEONHO 05002HR-H60Y
3 2 LED_POWER VBTX3P 14 38 RxP3
4 3 LED_STBY VBTX3N 15 37 RxN3
6 4 LED_WHITE GND 16 36 GND
CN001 5 5 SIRCS VBTX2P 17 35 RxP2
HKZ MAIN_5V 1 1 #30 2 6 H_GND VBTX2N 18 34 RxN2
H_GND 2 6 #30 1 7 KEY_GND GND 19 33 GND
LED_POWER 3 2 #30 3 8 POWER_Key VBTX1P 20 32 RxP1
LED_STBY 4 3 #30 2 9 TACT_KEY VBTX1N 21 31 RxN1
SIRCS 5 5 #30 7 10 3.3V_STBY GND 22 30 GND
LED_WHITE 6 4 #30 P/N:182115011 VBTX0P 23 29 RxP0
STBY_3.3V 7 10 #30 CN9501 VBTX0N 24 28 RxN0
P/N:1-820-184-11 GND 25 LVDS FFC 51P 27 GND
MOLEX 501331-0707 VBTXLOCKN0 26 26 LOCKN
VBTXHTPDN0 27 25 HTPDN
PANEL_PWM_M 28 24 PWMI
GND 29 23 NC
NC 30 22 NC
NC 31 21 NC
Wifi VCC_5V 1 1 1 1 VCC_5V PANEL_BINT 32 20 B_INT (High:Write / L/Open: Protect)
WoWLAN 2 2 2 2 WoWLAN SCL 33 19 SCL
FY17 DP 3 3 WIFI FFC 5P 3 3 DP SDA 34 18 SDA
DM 4 4 4 4 DM NC 35 17 NC
GND 5 5 5 5 GND NC 36 16 NC
P/N:179436241 NC 37 15 NC
CN9500 NC 38 14 GND From T-CON Board Source
NC 39 13 GND
GND 40 12 GND Board
NC/GND 41 11 GND
NC/GND 42 10 GND
NC 43 9 NC PANEL FFC pin PANEL FFC 60pin
12V 44 8 12V
FFC 60pin
12V 45 7 12V
12V 46 6 12V
LD Board
PSJ Board 12V 47 5 12V
12V 48 4 12V
12V 49 3 12V HIROSE TF06L-60S-0.5SH HIROSE TF06L-60S-0.5SH
12V 50 2 12V LSM GF05G-60S-MB-E2000 LSM GF05G-60S-MB-E2000
CN3000 12V 51 1 12V YEONHO 05002HR-H60Y YEONHO 05002HR-H60Y
1-843-953-11 IPEX : 1-842-546-21 or JAE FI-RE51S-HF
JAM 30pin Yamaichi : 1-843-107-12
PWM0(BLINKING) 1 28 #22 24 30 STBY_3.3V_OUT Molex: 1-844-527-11
IP_REF(DC DIMMER) 2 26 #22 3 29 FB_REF CN9000
FB_REF 3 29 #22 1 28 BLINKING
LD_MODE_SW 4 5 NC 27 PWM1_DIMMER
GND 5 4 2 26 DC_DIMMER 1-535-807-31
+3.3V 6 1 NC 25 PWM2_DIMMER JST SPS-01T-187*
Power Harness
GND 7 18 #22 30 24 STBY_3.3V_IN CN3109 4 1 L+ SPEAKER
GND 8 NC NC 23 PWM3_DIMMER P/N: 184256612 3 2 L- Front
GND 9 5 #22 14 22 BL_ON/ICSPCLK R+ 1 1 #24 1-780-577-11 Lch
GND 10 NC 12 21 BL_ERR R- 2 2 #24 JST WSPS-01T-110B*
AC_OFF_DET 11 NC 13 20 POWER_ON/ICSPDAT L- 3 2 #24
BL_ERR 12 21 #22 15 19 GND L+ 4 1 #24 1-535-807-31
MAIN_PWR 13 20 #22 7 18 GND (2.0Ch) JST SPS-01T-187*
BL_ON/ICSPCLK 14 22 #22 23 17 GND 1 1 R+ SPEAKER
GND 15 19 #22 16 16 REG_19V_12V 2 2 R- Front
REG_19V 16 16 #22 17 15 REG_19V_12V 1-780-577-11 Rch
REG_19V 17 15 #22 18 14 REG_19V_12V_Audio JST WSPS-01T-110B*
REG_19V_12V_Audio 18 14 #22 20 13 REG_12V
REG_19V_12V_Audio 19 12 #22 19 12 REG_19V_12V_Audio
REG_12V 20 13 #22 22 11 REG_12V
REG_19V_12V_Audio 21 NC 24 10 GND
REG_12V 22 11 #22 25 9 GND
GND 23 17 #22 29 8 GND
GND 24 10 #22 30 7 GND
GND 25 9 #22 NC 6 DC_DET_VTH/LD_MODE_SW
TCON_VCC12V 26 4 #22 9 5 GND
TCON_ON 27 3 #22 26 4 T-CON_VCC12V(NC)
TCON_VCC12V 28 2 #22 27 3 T-CON_ON
GND 29 8 #22 28 2 T-CON_VCC12V
GND 30 7 #22 6 1 STBY_3.3V
P/N:184391711
CN5500
19.5V
ADP IN
CN2000
1-820-294-11 (MOLEX)
LS Harness
LED_VCC1a 1 3A #30 Header:104127-0620 (MOLEX)
LED_VCC1b 2 4A #30 Housing:104128-0610 (MOLEX)
LED1 3 1A #30 3 1A LED1
LED2 4 2A #30 4 2A LED2
LED3 5 5A #30 1 3A VCC1a
LED4 6 6A #30 2 4A VCC1b
LED5 7 NC 5 5A LED3
LED7 8 1B #30 6 6A LED4
LED8 9 2B #30
LED9 10 5B #30 Header: 104127-0620 (MOLEX)
6B Housing:104128-0610 (MOLEX)
LED10
LED11
11
12 NC
#30
8 1B LED5
LS BAR
LED12 13 NC 9 2B LED6
LED_VCC2a 14 3B #30 14 3B VCC2a
LED_VCC2b 15 4B #30 15 4B VCC2b
10 5B LED7
11 6B LED8
information)
(Supplementary
145
SYS SET
SG 55’
2019/05/01 02:23:15 (GMT+09:00)
CN6801
1-822-360-11
53426-0510 Molex To LS
NC 1
+OUT1 2
NC 3
NC 4
-OUT1 5
1-535-807-31
JST SPS-01T-187*
SPEAKER L+ 1 4 CN3109
Front L- 2 3 P/N:184256612
Lch 1-780-577-11 #24 1 1 R+
JST WSPS-01T-110B* #24 2 2 R-
#24 2 3 L-
1-535-807-31 #24 1 4 L+
JST SPS-01T-187* (2.0Ch)
SPEAKER R+ 1 1
Front R- 2 2
Rch 1-780-577-11
JST WSPS-01T-110B*
2-A2 1 Ca
LS Bar A1
1-CN2 2 An
2-A3 1 Ca
LS Bar A2
1-A1 2 An
2-A4 1 Ca
LS Bar A3
1-A2 2 An
2-A5 1 Ca
LS Bar A4
1-A3 2 An
information)
(Supplementary
2-A6 1 Ca
LS Bar A5
1-A4 2 An
2-A7 1 Ca
LS Bar A6
1-A5 2 An
2-A8 1 Ca
LS Bar A7
1-A6 2 An
146
2-A9 1 Ca
LS Bar A8
1-A7 2 An
2-A10 1 Ca
LS Bar A9
1-A8 2 An
1-CN5 1 Ca
LS Bar A10
1-A9 2 An
JST SFKR-02V-2
SYS SET
SG 65’
2019/05/01 02:23:15 (GMT+09:00)
CN6801
1-822-360-11
53426-0510 Molex To LS
NC 1
+OUT1 2
NC 3
NC 4
-OUT1 5
1-535-807-31
JST SPS-01T-187*
SPEAKER L+ 1 4 CN3109
Front L- 2 3 P/N:184256612
Lch 1-780-577-11 #24 1 1 R+
JST WSPS-01T-110B* #24 2 2 R-
#24 2 3 L-
1-535-807-31 #24 1 4 L+
JST SPS-01T-187* (2.0Ch)
SPEAKER R+ 1 1
Front R- 2 2
Rch 1-780-577-11
JST WSPS-01T-110B*
2-A2 1 Ca
LS Bar A1
1-CN2 2 An
2-A3 1 Ca
LS Bar A2
1-A1 2 An
2-A4 1 Ca
LS Bar A3
1-A2 2 An
2-A5 1 Ca
LS Bar A4
1-A3 2 An
information)
(Supplementary
2-A6 1 Ca
LS Bar A5
1-A4 2 An
2-A7 1 Ca
LS Bar A6
1-A5 2 An
2-A8 1 Ca
LS Bar A7
1-A6 2 An
2-A9 1 Ca
147
LS Bar A8
1-A7 2 An
2-A10 1 Ca
LS Bar A9
1-A8 2 An
1-CN5 1 Ca
LS Bar A10
1-A9 2 An
JST SFKR-02V-2
SYS SET
2019/05/01 02:23:15 (GMT+09:00)