Professional Documents
Culture Documents
CAPPUCCINO
DOOR LOCK
MACHINE DOOR
LIQUID WASTE TRAY
WATER TANK
GRILLE
UPPER LID
DECAFF FLAP
MIXER
MILKER
SPOUT HOLDER
ESPRESSO UNIT
FRESH MILK HOSE
03-2008 U3115EN00
1 2 B
A
XA
M
B
A
LOADING
1 2
REGULAR CLEANING
Emptying the liquid waste tray: Emptying the liquid waste tray: ON
When the red float signal lifts up through the grille, it is necessary to • Take hold of the sides of the liquid waste tray (A) firmly, then lift
empty the liquid waste tray immediately. The dispenser will then slightly and pull forward.
work normally. It is advisable not to wait until the red drip tray full • Empty the tray and if necessary, wash it using a mild detergent
indicator is visible. It is recommended that the liquid waste tray solution.
is emptied regularly. • Re-fit the tray back into position.
WASTE
3 A TRAY FULL 4
REGULAR CLEANING
ON
1 2 REMOVE MILK
CONFIRM?
• At power-on and during a mixer rinse the machine proposes the • Take the priming tube out of the fresh milk container.
steps to be carried out for washing the milk circuit. • Press the confirmation button (third one) to continue.
• It may be useful to place a container under the spouts for collect-
ing the liquid residue from washing.
3 INSERT DETERGENT
CONFIRM? 4 REMOVE DETERGENT
CONFIRM?
DETERGENT CYCLE
CONFIRM?
CLE N E R
A
CLE N E R
A
• Insert the priming tube in a container with a detergent solution. • Take the priming tube out of the container with the solution used.
• Press twice the confirmation button (third one) to start the clean- • Press the confirmation button (third one) to continue.
ing cycle.
5 INSERT WATER
CONFIRM? 6 INSERT MILK
CONFIRM?
CLEAN CYCLE
CONFIRM?
W AT E R
W AT E R
• Insert the priming tube in un container with clean water. • Replace the priming tube in the fresh milk container.
• Press twice the confirmation button (third one) to start the rinse • Press the confirmation button (third one) to complete.
cycle. • Empty out all washing residue from the liquid waste container.
C
D
E
THE MILKER NOZZLE MUST BE DISASSEMBLED
REGULARLY FOR CLEANING.
• Open the machine door and disconnect tubes (B) and (C) from • Rotate and pull at the same time part (A).
the milker (A). • Rotate and pull at the same time part (B).
• Remove the milker from the spouts support. • Separate parts (C), (D) and (E).
3 4
A
C L E A NER C
D
DO NOT USE DETERGENTS THAT ARE E
TOO SCENTED.
• Wash all parts with the detergent solution taking care to mechani- • Reassemble parts (C), (D) and (E).
cally remove all visible residue and product layers, using a brush, • Replace part (B) and rotate to secure it.
if necessary. • Replace part (A) and rotate to secure it.
• Rinse and dry thoroughly all parts.
5 B C A 6
• Replace milker nozzle (A) in the spouts support. • Close the machine door.
• Correctly reconnect tubes (B) and (C) to the milker nozzle.
AT POWER-ON THE PROCEDURE FOR WASHING THE MILK CIRCUIT
IS PROPOSED.
PRESS THE THIRD BUTTON TO START THE PROCEDURE OR ANY
OTHER BUTTON TO SKIP THE OPERATION.
1 2
A A
C B
B C
Removing and sanitising the mixer: Removing and sanitising the mixer:
• Detach tube from mixer. • Separate all the mixer assembly components: product funnel
• Rotate the product dispensing nozzle (A) upwards to make (A), powder deposit drawer (B), mixing bowl (C).
operation easier. • Wash, rinse and dry completely.
• Rotate the lever (B) anticlockwise.
• Take hold of the mixer assembly (C) firmly, and pull.
3 4
C
A
5 6
B
A B
C D A
Cleaning the dispensing spouts: Assembling of the dispensing spouts carrier plate:
• Detach the tubes (A) from the dispensing spouts. • Insert the dispensing spout holder (A) into guide (B) press until it
• Press pushbutton (B) to release the dispensing spouts carrier clicks.
plate (C). • Reinsert the dispensing spouts onto the spout holder and connect
• Detach the dispensing spouts (D) from spout holder (C). the tubes onto their spouts.
• Thoroughly, wash and clean all the relative components.
7 8
A
Instant powder container: Removing and cleaning the espresso brewing unit:
• Open the door of the dispenser and lift the lid. • Undo the hose connection ring (A) making sure not to lose the
• Lightly push back and lift the instant powder container. gasket.
• Remove it from the dispenser. • Detach the coffee waste conveyor (B).
• Brush the container and base. • Undo fixing pin (C).
• Refit the container into dispenser. • Remove the espresso brewing unit (D).
• Brewer unit can be washed with running water.
• Dry and re fit the espresso brewing unit.
9 10
Removing and cleaning the espresso brewing unit: Internal dispenser cleaning:
• Every time the unit is filled up or at least once weekly, remove any • Clean the inside of the dispenser using a mild detergent solu-
coffee residues from around the brewing unit (A). tion.
• To do so, simply use a brush (B) or a small vacuum cleaner. • Do not use scented cleaning products.
N&W GLOBAL VENDING S.p.A. - Via Roma, 24 - 24030 Valbrembo (BG) Italy - Tel. +39 035606111 - Web: www.nwglobalvending.com