Professional Documents
Culture Documents
ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right
to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON
Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON
Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s
technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA
Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended
or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor
is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
Single-Channel: 6N137, HCPL2601, HCPL2611 Dual-Channel: HCPL2630, HCPL2631 — High Speed 10MBit/s Logic Gate Optocouplers
January 2011
8
N/C 1 8 VCC + 1 8 VCC
1
VF1
+ 2 7 VE _ 2 7 V01
VF
8
_ _ 8
3 6 VO 3 6 V02
1
1
V
F2
*For peak soldering reflow, please refer to the Reflow Profile on page 11.
Switching Characteristics (TA = -40°C to +85°C, VCC = 5V, IF = 7.5mA unless otherwise specified)
Symbol AC Characteristics Test Conditions Min. Typ.* Max. Unit
TPLH Propagation Delay RL = 350Ω, TA = 25°C 20 45 75 ns
Time to Output HIGH CL = 15pF(4) (Fig. 12) 100
Level
TPHL Propagation Delay TA = 25°C(5) 25 45 75 ns
Time to Output LOW RL = 350Ω, CL = 15pF (Fig. 12) 100
Level
|TPHL–TPLH| Pulse Width Distortion (RL = 350Ω, CL = 15pF (Fig. 12) 3 35 ns
(6)
tr Output Rise Time RL = 350Ω, CL = 15pF (Fig. 12) 50 ns
(10–90%)
tf Output Rise Time RL = 350Ω, CL = 15pF(7) (Fig. 12) 12 ns
(90–10%)
tELH Enable Propagation IF = 7.5mA, VEH = 3.5V, RL = 350Ω, CL = 15pF(8) 20 ns
Delay Time to Output (Fig. 13)
HIGH Level
tEHL Enable Propagation IF = 7.5mA, VEH = 3.5V, RL = 350Ω, CL = 15pF(9) 20 ns
Delay Time to Output (Fig. 13)
LOW Level
|CMH| Common Mode TA = 25°C, |VCM| = 50V 6N137, HCPL2630 10,000 V/µs
Transient Immunity (Peak), IF = 0mA, HCPL2601, HCPL2631 5000 10,000
(at Output HIGH Level) VOH (Min.) = 2.0V,
RL = 350Ω(10) (Fig. 14)
|VCM| = 400V HCPL2611 10,000 15,000 V/µs
|CML| Common Mode RL = 350Ω, IF = 7.5mA, 6N137, HCPL2630 10,000
Transient Immunity VOL (Max.) = 0.8V, HCPL2601, HCPL2631 5000 10,000
(at Output LOW Level) TA = 25°C(11) (Fig. 14)
|VCM| = 400V HCPL2611 10,000 15,000
Notes:
1. The VCC supply to each optoisolator must be bypassed by a 0.1µF capacitor or larger. This can be either a ceramic
or solid tantalum capacitor with good high frequency characteristic and should be connected as close as possible
to the package VCC and GND pins of each device.
2. Each channel.
3. Enable Input – No pull up resistor required as the device has an internal pull up resistor.
4. tPLH – Propagation delay is measured from the 3.75mA level on the HIGH to LOW transition of the input current
pulse to the 1.5 V level on the LOW to HIGH transition of the output voltage pulse.
5. tPHL – Propagation delay is measured from the 3.75mA level on the LOW to HIGH transition of the input current
pulse to the 1.5 V level on the HIGH to LOW transition of the output voltage pulse.
6. tr – Rise time is measured from the 90% to the 10% levels on the LOW to HIGH transition of the output pulse.
7. tf – Fall time is measured from the 10% to the 90% levels on the HIGH to LOW transition of the output pulse.
8. tELH – Enable input propagation delay is measured from the 1.5V level on the HIGH to LOW transition of the input
voltage pulse to the 1.5V level on the LOW to HIGH transition of the output voltage pulse.
9. tEHL – Enable input propagation delay is measured from the 1.5V level on the LOW to HIGH transition of the input
voltage pulse to the 1.5V level on the HIGH to LOW transition of the output voltage pulse.
10. CMH – The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
HIGH state (i.e., VOUT > 2.0V). Measured in volts per microsecond (V/µs).
11. CML – The maximum tolerable rate of rise of the common mode voltage to ensure the output will remain in the
LOW output state (i.e., VOUT < 0.8V). Measured in volts per microsecond (V/µs).
12. Device considered a two-terminal device: Pins 1, 2, 3 and 4 shorted together, and Pins 5, 6, 7 and 8 shorted
together.
Conditions:
IF = 5 mA 30
0.7 VE = 2 V 16
0.5 1
IOL = 16mA
0.4
0.1
0.3
IOL = 6.4mA
0.2 0.01
IOL = 9.6mA
0.1
0.001
0.0
-40 -20 0 20 40 60 80 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6
TA – AMBIENT TEMPERATURE (°C) VF – FORWARD VOLTAGE (V)
Fig.3 Switching Time vs. Forward Current Fig. 4 Low Level Output Current
vs. Ambient Temperature
120 50
IF = 15mA
100 45
IF = 10mA
RL = 4 kΩ (TPLH)
80 40
IF = 5mA
60 35
RL = 1 kΩ (TPLH)
40 30
Conditions:
VCC = 5 V
VE = 2 V
20 25 VOL = 0.6 V
RL = 1 kΩ
RL = 4 kΩ (TPHL)
RL = 350 Ω (TPLH) RL = 350 kΩ
0 20
5 7 9 11 13 15 -40 -20 0 20 40 60 80
IF – FORWARD CURRENT (mA) TA – AMBIENT TEMPERATURE (°C)
Fig. 5 Input Threshold Current Fig. 6 Output Voltage vs. Input Forward Current
vs. Ambient Temperature
6
IFT – INPUT THRESHOLD CURRENT (mA)
4
Conditions:
VCC = 5.0 V
VO = 0.6 V 5
VO – OUTPUT VOLTAGE (V)
RL = 350Ω
3 4
RL = 350Ω RL = 4kΩ RL = 1kΩ
3
RL = 1kΩ
2 2
RL = 4kΩ
1 0
-40 -20 0 20 40 60 80 0 1 2 3 4 5 6
TA – AMBIENT TEMPERATURE (°C) IF - FORWARD CURRENT (mA)
RL = 4 kΩ RL = 4 kΩ (tr)
500
40
300
200
20
RL = 1 kΩ RL = 1 kΩ (tr)
100
RL = 350Ω (tr)
0 RL = 350Ω
0 RL = 1 kΩ
RL = 4 kΩ (tf)
RL = 350Ω
-60 -40 -20 0 20 40 60 80 100 -60 -40 -20 0 20 40 60 80 100
TA – TEMPERATURE (°C) TA – TEMPERATURE (°C)
Fig. 9 Enable Propagation Delay vs. Temperature Fig. 10 Switching Time vs. Temperature
120 120
TE – ENABLE PROPAGATION DELAY (ns)
RL = 4 kΩ TPLH
TP – PROPAGATION DELAY (ns)
100
100
RL = 4 kΩ (TELH)
80
80
60
60
40
RL = 1 kΩ (TELH) RL = 1 kΩ TPLH
Conditions:
VCC = 5.5 V
VO = 5.5 V
15 VE = 2.0 V
IF = 250 µA
10
0
-60 -40 -20 0 20 40 60 80 100
TA – TEMPERATURE (°C)
Pulse
Generator
tr = 5ns
Z O = 50Ω +5V
IF = 7.5 mA
.1 µf Output
2 7 RL
(VO )
bypass
1.5 V
Input Output
Monitor
3 6 (VO ) 90%
Output
(I F) CL
(VO )
10%
47 4 GND 5
tf tr
Pulse
Generator Input
tr = 5ns Monitor
Z O = 50Ω (V E)
+5V
3.0 V
VCC Input
(VE ) 1.5 V
1 8
t EHL t ELH
7.5 mA
Output
2 7 .1 µf
RL
(VO )
bypass 1.5 V
Output
3 6 (VO )
CL
4 5
GND
VCC
1 8 +5V
IF
A 2 7 .1 µf 350Ω
bypass
B
Output
VFF 3 6 (VO)
4 5
GND
VCM
Pulse Gen
Peak
VCM
0V
5V CM H
Switching Pos. (A), IF = 0
VO
VO (Min)
VO (Max)
Marking Information
2601 2
6
V XX YY T1
3 4 5
Definitions
1 Fairchild logo
2 Device number
3 VDE mark (Note: Only appears on parts ordered with VDE option –
See order entry table)
4 Two digit year code, e.g., ‘03’
5 Two digit work week ranging from ‘01’ to ‘53’
6 Assembly package code
7.5 ± 0.1
13.2 ± 0.2 16.0 ± 0.3
10.30 ± 0.20
Reflow Profile
300
215 C, 10–30 s
250
Temperature (°C)
225 C peak
200
150
50 Ramp up = 3C/sec
0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5
Time (Minute)
Authorized Distributor
Fairchild Semiconductor:
HCPL2601S HCPL2601 HCPL2601SDV HCPL2601WV HCPL2601SV HCPL2601SD HCPL2601V