Professional Documents
Culture Documents
14’ 0”
14'0" (4267)
(4267)
7' 8-1/2"
12' 1-3/4" (2350)
(3.7m)
6' 3-1/4"
(1911)
TAILSWING
45"
(1143)
7' 11-1/8"
(2416)
7' 11-1/2"
(2424)
46-1/2"
(1181)
15" 13-1/4"
(382) 27° (334) 27°
2 GROVE YB4415/YB4415XT
Working Range D6-829-100760
70
15
60 45° OFFSET
25
30°
30 3'- 4"
20
17
20°
20
10° 80° MAX
BOOM ANGLE
10
0°
0
60 50 40 30 20 10
AXIS OF ROTATION
A6-829-100240-1
70
50 70°
3'- 8"
60° 40
50° 35
40
40° 30
25
30°
30 3'- 4"
20
17
20°
20
10° 80° MAX
BOOM ANGLE
10
0°
0
60 50 40 30 20 10
AXIS OF ROTATION
D6-829-100240-2
70
50 41.4 (40)
60°
0
60 50 40 30 20 10
AXIS OF ROTATION
3 GROVE YB4415/YB4415XT
Superstructure Specifications
Boom Hydraulic System
17 ft. - 40 ft. (5.1 m - 12.2 m) three-section full power boom. Three (3) section main gear pumps driven off torque converter
Maximum tip height: 47 ft. (14.4 m). through PTO.
Speeds: 32 seconds (ext.); 19 seconds (retract).
Combined capacity: 75 GPM (285 LPM).
*Optional Boom
21 ft. - 52 ft. (6.5 m - 15.6 m) three-section full power boom. Maximum system operating pressure: 3,500 psi (241 bar).
Maximum tip height: 59 ft. (18.0 m).
Speeds: 43 seconds (ext.); 25 seconds (retract). Three valve banks mounted on top of dash panel with direct
mechanical linkage low effort lever controls.
*Fixed Boom Extension (non-offsettable) Return line type filter with full flow by-pass protection and service
15 ft. (4.6 m) swingaway extension w/single metallic sheave in indicator. 10 micron rated replaceable cartridges.
point. Stows alongside base boom section for travel. Extends tip
heights to 62 ft. (18.9 m) or 74 ft. (22.5 m) with the 40 ft. (12.2 m) 54 gallon (205 L) reservoir with sight level gauge and steel plate to
and 52 ft. (15.6 m) booms respectively. guard against side impact damage.
*Offsettable Boom Extension *Remote-mounted oil cooler with thermostatically controlled electric
15 ft. (4.6 m) swingaway extension w/single metallic sheave in motor driven fan.
point. Stows alongside base boom section for travel. Extends tip
heights to 62 ft. (18.9 m) or 74 ft. (22.5 m) with the 40 ft. (12.2 m) System pressure and flow test ports with quick release type fittings
and 52 ft. (15.6 m) booms respectively. Can be offset at 0° or 45° for each circuit.
to increase up and over reach.
HOIST SPECIFICATIONS - Model HP12-13G
Boom Nose Planetary reduction with automatic spring applied multi-wet-disc
Two (2) position low profile and quick reeve design with two brake and grooved hoist drum. *Cable follower available.
metallic sheaves mounted on tapered roller bearings and quick
removable pin-type rope guards. Head pivots forward (up) to the Drum Dim. (Dia. x Lg.) 10.63” x 13.4”
low profile position (1-2 parts of line only & max 70° boom (270 mm x 341 mm)
elevation) for minimizing head space requirements or rearward
(down) to the conventional position for maximum lifts that exceed 2
parts of line reeving or approximately 18,000 lbs. (8165 kg). Maximum Single Line Pull: 10,930 lbs.
(4958 kg)
Boom Elevation
Twin double acting hydraulic cylinders with integral holding valves Maximum Single Line Speed: 134 - 178 FPM
provide elevation from 0° to 80°. Mechanical boom angle indicator. (41 - 54 m/min)
Speeds: 20 seconds (ext.) 14 seconds (retract).
Maximum Permissible Single Line Pull:
Anti-Two Block Device - The standard low profile type Standard Rope 5/8” (16 mm)
anti-two block device, when activated, provides an audible-visual (6 x 37 Class): 9,080 lbs. (3.5:1 FOS)
warning to the crane operator and disengages all crane functions (4119 kg)
whose movement can cause two-blocking.
*Optional Rope 5/8” (16 mm)
*Rated Capacity Limiter (RCL) (18 x 19 Class): 9,080 lbs. (5:1 FOS)
(4119 kg)
A simple, effective and easy to use overload protection system in
conjunction with a low profile type anti-two block (A2B) device
assists the operator in the efficient operation of the unit. The RCL
system constantly monitors actual lifting conditions versus Rope Length (Std.): 250 ft. (76.2 m) w/40 ft. (12.2 m) boom
allowable capacity ratings to assist in preventing an overload 310 ft. (94.5 m) w/52 ft. (15.6 m) boom
condition. It provides the operator with a visual pre-warning at
approximately 90% of the rated capacity and an audible-visual Maximum Rope Stowage: 374 ft. of 5/8”
warning in combination with automatic lockout at approximately (114 m of 16 mm)
100% of rated capacity.
Usable: 269 ft. of 5/8”
(82 m of 16 mm)
Swing
Ball bearing swing circle with 360° continuous rotation. Hydraulic
motor driven worm and gear reducer.
Maximum speed: 2.0 RPM.
Counterweight
4,300 lbs. (1950 kg) w/40 ft. (12.2 m) boom; 4,800 lbs. (2177 kg)
w/52 ft. (15.6 m) boom; bolted to the turntable.
4 GROVE YB4415/YB4415XT
Chassis Specifications
Frame Transmission
High strength alloy steel construction with integral outrigger Remote mounted Clark 3 speed forward and reverse full powershift w/engine
housings; front/rear lifting, towing and tie down lugs and recessed mounted torque converter and stalk type shift control mounted to the steering
lifting points in all four corners of deck top. Carry deck constructed of 1/4” (6 column. Controls permit quick and easy shuttle control between forward and
mm) thick plate steel w/surface area of 66 sq. ft. (6.1 m2) and anti-skid deck reverse travel.
treatment.
Axles
Outriggers Front: Planetary drive/steer with internal
Front and rear oblique type beams at all four corners with integral holding multi-wet-disc brakes and limited slip differential.
valves. Outrigger pads form an integral part of the beam and have a surface Rear: (4 x 2) Fabricated steer axle with internal wet disc brakes.
area of 103 sq. in. (665 cm2). (4x4 drive) Planetary drive/steer with internal wet disc brakes and
Maximum outrigger pad load: 26,539 lbs. (12 038 kg). limited slip differential.
GROVE YB4415/YB4415XT 5
RATED LIFTING CAPACITIES IN POUNDS
ON OUTRIGGERS FULLY EXTENDED - 360°
*Boom length varies between boom nose sheaves in down position (in bold), or up & out
position (in parenthesis).
1. Capacities do not exceed 85% of tipping loads as determined by test in accordance with SAE J765.
2. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon
as a capacity limitation.
3. With boom nose sheaves down (in lower position), single, 2-part or 4-part line may be used. With boom nose
sheaves up and out (low profile position), single or 2-part line may be used, with maximum boom angle limited
to 70°.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
6 GROVE YB4415/YB4415XT
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY - 360°
Radius Main Boom Length in Feet
in
Feet *17 (18.4) *20 (21.4) *25 (26.4) *30 (31.4) *35 (36.4) *40 (41.4)
*Boom length varies between boom nose sheaves in down position (in bold), or up & out
position (in parenthesis).
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 7
15 FT. EXTENSION
RATED LIFTING CAPACITIES IN POUNDS
NOTES:
1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping
loads on outriggers in accordance with SAE J765.
2. 15 ft. boom extension may be used for single line lifting service only.
3. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
with boom extension occurs rapidly and without advance warning.
4. Capacities listed are with fully extended outriggers only.
5. No load stability on outriggers fully extended 360° with 15 ft. extension installed:
a. Minimum boom angle for 40 ft. main boom = 0°
b. Maximum main boom length at 0° main boom angle = 40 ft.
6. When lifting loads the minimum allowable boom angle is 3°.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
8 GROVE YB4415/YB4415XT
15 FT. EXTENSION
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY 360°
Radius Main Boom Length in Feet
in
Feet 17 20 25 30 35 40
15 FT. EXTENSION
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY - DEFINED ARC OVER FRONT
Radius Main Boom Length in Feet
in
Feet 17 20 25 30 35 40
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 9
15 FT. OFFSETTABLE EXTENSION AT 0° OFFSET
RATED LIFTING CAPACITIES IN POUNDS
12 4,310
14 4,140 4,210 4,300
16 4,000 4,070 4,170 4,240 4,300
18 3,890 3,950 4,050 4,130 4,200 4,260
20 3,810 3,860 3,960 4,040 4,110 4,170
22 3,740 3,800 3,880 3,960 4,030 4,090
24 3,740 3,820 3,890 3,960 4,020
26 3,780 3,830 3,900 3,960
28 3,720 3,790 3,850 3,900
30 3,760 3,810 3,850
32 3,780 3,820
34 3,740 3,790
36 3,710 3,730
38 3,380
Lifting Capacity at Forty Eight Degree Boom Angle
NOTES:
On Outriggers Fully Extended - 360°
1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping
Main Boom Length in Feet loads on outriggers in accordance with SAE J765.
Boom 2. 15 ft. boom extension may be used for single line lifting service only.
Angle 17 20 25 30 35 40 3. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
with boom extension occurs rapidly and without advance warning.
3,710 3,710 3,710 3,710 3,670 3,110 4. Capacities listed are with fully extended outriggers only.
48° ** 5. No load stability on outriggers fully extended 360° with 15 ft. extension installed at 45° offset:
(23.5) (25.7) (29.2) (32.7) (36.3) (39.8)
a. Minimum boom angle for 40 ft. main boom = 45°
Note: ( ) Ref. radii in feet. b. Maximum main boom length at 45° main boom angle = 40 ft.
A6-829-100725
** Radii are with the extension at horizontal. 6. When lifting loads the minimum allowable boom angle is 48° at 45° offset.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
10 GROVE YB4415/YB4415XT
15 FT. OFFSETTABLE EXTENSION AT 0° OFFSET
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY 360°
Radius Main Boom Length in Feet
in
Feet 17 20 25 30 35 40
12 4,310
14 4,140 4,210 4,300
16 4,000 4,070 4,170 4,240 *4,300
18 3,890 3,950 4,050 4,130 4,200 4,260
20 3,700 3,700 3,700 3,700 3,700 3,700
22 3,160 3,160 3,160 3,160 3,160 3,160
24 2,730 2,730 2,730 2,730 2,730
26 2,370 2,370 2,370 2,370
28 2,070 2,070 2,030 2,030
30 1,760 1,760 1,760
32 1,570 1,570 1,570
NOTES:
34 1,320 1,270 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 75% of tipping
36 1,040 loads on rubber in accordance with SAE J765.
2. 15 ft. boom extension may be used for single line lifting service only.
38 860 3. Defined Arc - Over front includes 6° on either side of longitudinal centerline of machine. Pick and carry lifting NOT
permitted.
Lifting Capacity at Forty Eight Degree Boom Angle
On Rubber - 360° 4. Capacities are applicable to machines equipped with 385/65R22.5 (J) Firestone T839 tires at 140 psi cold inflation pressure.
5. Capacities are applicable only with machine on firm level surface.
Boom Main Boom Length in Feet 6. All rubber lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation
Angle pressures. Damaged tires are hazardous to safe operation of crane.
17 20 25 30 35 40 7. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
2,830 2,425 1,920 1,530 1,100 670 with boom extension occurs rapidly and without advance warning.
48° ** 8. No load stability on rubber 360° with 15 ft. extension installed at 45° offset:
(23.5) (25.7) (29.2) (32.7) (36.3) (39.8)
a. Minimum boom angle for 40 ft. main boom = 45°
Note: ( ) Ref. radii in feet. b. Maximum main boom length at 45° main boom angle = 40 ft.
* This capacity based on maximum boom angle. A6-829-100727
** Radii are with the extension at horizontal. 9. When lifting loads the minimum allowable boom angle is 48° at 45° offset.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 11
15 FT. OFFSETTABLE EXTENSION AT 0° OFFSET
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY - DEFINED ARC OVER FRONT
Radius Main Boom Length in Feet
in
Feet 17 20 25 30 35 40
12 4,310
14 4,140 4,210 4,300
16 4,000 4,070 4,170 4,240 4,300
18 3,890 3,950 4,050 4,130 4,200 4,260
20 3,810 3,860 3,960 4,040 4,110 4,170
22 3,740 3,800 3,880 3,960 4,030 4,090
24 3,740 3,820 3,890 3,960 4,020
26 3,780 3,830 3,900 3,960
28 3,720 3,750 3,750 3,750
30 3,310 3,310 3,310
32 2,930 2,930 2,930
34 2,610 2,610 ad a e t t e e te s o at o o ta
NOTES:
36 2,320 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 75% of tipping
loads on rubber in accordance with SAE J765.
38 2,080
2. 15 ft. boom extension may be used for single line lifting service only.
Lifting Capacity at Forty Eight Degree Boom Angle 3. Defined Arc - Over front includes 6° on either side of longitudinal centerline of machine. Pick and carry lifting NOT permitted.
On Rubber - Defined Arc Over Front 4. Capacities are applicable to machines equipped with 385/65R22.5 (J) Firestone T839 tires at 140 psi cold inflation pressure.
5. Capacities are applicable only with machine on firm level surface.
Boom Main Boom Length in Feet 6. All rubber lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation
pressures. Damaged tires are hazardous to safe operation of crane.
Angle 17 20 25 30 35 40 7. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
with boom extension occurs rapidly and without advance warning.
3,710 3,710 3,470 2,810 2,280 1,880
48° ** 8. No load stability on rubber (defined arc) with 15 ft. extension installed at 45° offset:
(23.5) (25.7) (29.2) (32.7) (36.3) (39.8) a. Minimum boom angle for 40 ft. main boom = 45°
Note: ( ) Ref. radii in feet. b. Maximum main boom length at 45° main boom angle = 40 ft.
A6-829-100729
** Radii are with the extension at horizontal. 9. When lifting loads the minimum allowable boom angle is 48° at 45° offset.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
12 GROVE YB4415/YB4415XT
WORKING RANGE DIAGRAM
(BOOM DEFLECTION NOT SHOWN) D6-829-100778
80 0° OFFSET
45° OFFSET
15
70
60°
45
20
10°
80° MAX
BOOM ANGLE
10
0°
0
60 50 40 30 20 10
AXIS OF ROTATION
15
70
60°
45
HEIGHT FROM GROUND IN FEET
50 50°
40
40° 35
40
30 3' -4"
30°
25
30 21
20°
20
10°
80° MAX
BOOM ANGLE
10 0°
0
60 50 40 30 20 10
AXIS OF ROTATION
OPERATING RADIUS IN FEET FROM AXIS OF ROTATION
60°
3' -6"
46.4 (45)
50°
50
HEIGHT FROM GROUND IN FEET
41.4 (40)
40° 36.4 (35)
40
31.4 (30)
30°
26.4 (25)
30 22.4 (21) 3' -2"
20°
20
10°
70° MAX
BOOM ANGLE
10
0°
0
60 50 40 30 20 10 AXIS OF ROTATION
GROVE YB4415/YB4415XT 13
RATED LIFTING CAPACITIES IN POUNDS
ON OUTRIGGERS FULLY EXTENDED - 360°
*Boom length varies between boom nose sheaves in down position (in bold), or up & out position (in
parenthesis).
1. Capacities do not exceed 85% of tipping loads as determined by test in accordance with SAE J765.
2. Capacities appearing above the bold line are based on structural strength and tipping should not be relied upon as a capacity
limitation.
3. With boom nose sheaves down (in lower position), single, 2-part or 4-part line may be used. With boom nose sheaves up and
out (low profile position), single or 2-part line may be used, with maximum boom angle limited to 70°.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
14 GROVE YB4415/YB4415XT
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY - 360°
Radius Main Boom Length in Feet
in
Feet *21 (22.8) *25 (26.4) *30 (31.4) *35 (36.4) *40 (41.4) *45 (46.4) *52 (53.4)
*Boom length varies between boom nose sheaves in down position (in bold), or up & out position (in
parenthesis).
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 15
15 FT. EXTENSION
RATED LIFTING CAPACITIES IN POUNDS
NOTES:
1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads on
outriggers in accordance with SAE J765.
2. 15 ft. boom extension may be used for single line lifting service only.
3. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom
extension occurs rapidly and without advance warning.
4. Capacities listed are with fully extended outriggers only.
5. When lifting loads the minimum allowable boom angle is 3°.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
16 GROVE YB4415/YB4415XT
15 FT. EXTENSION
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY 360°
Radius Main Boom Length in Feet
in
Feet 21 25 30 35 40 45 52
15 FT. EXTENSION
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY - DEFINED ARC OVER FRONT
Radius Main Boom Length in Feet
in
Feet 21 25 30 35 40 45 52
6 9,080 9,080 9,080 **9,080
8 9,080 9,080 9,080 9,080
10 9,080 9,080 9,080 9,080 9,080 **9,080
12 8,370 9,080 9,080 9,080 9,080 9,080 **9,080
14 7,510 8,150 8,780 9,080 9,080 9,080 9,080
16 6,810 7,400 8,060 8,410 8,600 8,600 8,600
18 6,220 6,770 7,440 7,600 7,600 7,600 7,600
20 5,630 6,240 6,760 6,760 6,760 6,760 6,760
22 5,110 5,690 5,910 5,910 5,910 5,910 5,910
24 4,680 5,110 5,110 5,110 5,110 5,110 5,110
26 4,310 4,450 4,450 4,450 4,450 4,450 4,450
28 3,920 3,920 3,920 3,920 3,920 3,920 3,920
30 3,470 3,470 3,470 3,470 3,470 3,470 3,470
32 3,080 3,080 3,080 3,080 3,080 3,080 3,080
34 2,750 2,750 2,750 2,750 2,750 2,750
36 2,460 2,460 2,460 2,460 2,460 2,460
38 2,210 2,210 2,210 2,210 2,210
40 1,990 1,990 1,990 1,990 1,990
45 1,530 1,530 1,530 1,530
50 1,170 1,170 1,170
55 880 880
Minimum boom angle (°) for indicated length (no load) 0
NOTES:
Maximum boom length (ft.) at 0° boom angle (no load) 52 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 75% of tipping loads on
Lifting Capacity at Three Degree Boom Angle rubber in accordance with SAE J765.
On Rubber - Defined Arc Over Front 2. 15 ft. boom extension may be used for single line lifting service only.
3. Defined Arc - Over front includes 6° on either side of longitudinal centerline of machine. Pick and carry lifting NOT permitted.
Boom Main Boom Length in Feet
4. Capacities are applicable to machines equipped with 385/65R22.5 (J) Firestone T839 tires at 140 psi cold inflation pressure.
Angle 21 25 30 35 40 45 5. Capacities are applicable only with machine on firm level surface.
6. All rubber lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation
2,850 2,330 1,790 1,370 1,050 780 pressures. Damaged tires are hazardous to safe operation of crane.
3°
(33.4) (37) (42) (47) (52) (57) 7. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom
**This capacity is based upon maximum boom angle.
A6-829-100756
extension occurs rapidly and without advance warning.
Note: ( ) Ref. radii in feet. 8. When lifting loads the minimum allowable boom angle is 3°.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 17
15 FT. OFFSETTABLE EXTENSION AT 0° OFFSET
RATED LIFTING CAPACITIES IN POUNDS
12 4,450 *4,500
14 4,280 4,350 *4,420 *4,480
16 4,140 4,210 4,290 4,360 *4,420 *4,460
18 4,020 4,090 4,180 4,250 4,310 4,360 4,420
20 3,920 3,990 4,080 4,150 4,220 4,270 4,330
22 3,850 3,910 3,990 4,070 4,130 4,190 4,260
24 3,800 3,850 3,920 3,990 4,060 4,120 4,180
26 3,710 3,800 3,860 3,930 3,990 4,050 4,120
28 3,730 3,820 3,870 3,930 3,990 4,060
30 3,780 3,830 3,880 3,940 4,000
32 3,710 3,800 3,840 3,890 3,950
34 3,750 3,810 3,850 3,910
36 2,930 3,750 3,750 3,750
38 3,400 3,400 3,400
40 3,080 3,080
45 2,440
Lifting Capacity at Forty Eight Degree Boom Angle
On Outriggers Fully Extended - 360°
NOTES:
Boom Main Boom Length in Feet 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 85% of tipping loads on
Angle outriggers in accordance with SAE J765.
21 25 30 35 40 45 52 2. 15 ft. offsettable boom extension may be used for single line lifting service only.
3. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping with boom
3,710 3,710 3,630 2,810 2,180 1,680 1,130 extension occurs rapidly and without advance warning.
48° **
(26.7) (29.2) (32.7) (36.3) (39.8) (43.3) (48.3) 4. Capacities listed are with fully extended outriggers only.
5. No load stability on outriggers fully extended 360° with 15 ft. offsettable extension installed at 45° offset:
Note: ( ) Ref. radii in feet. A6-829-100749A a. Minimum boom angle for 52 ft. main boom = 45°
*This capacity based on maximum boom angle. b. Maximum main boom length at 45° main boom angle = 52 ft.
**Radii are with extension at horizontal. 6. When lifting loads the minimum allowable boom angle is 48° at 45° offset.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
18 GROVE YB4415/YB4415XT
15 FT. OFFSETTABLE EXTENSION AT 0° OFFSET
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY 360°
Radius Main Boom Length in Feet
in
Feet 21 25 30 35 40 45 52
12 *4,450 *4,500
14 4,280 4,350 *4,420 *4,480
16 4,140 4,210 4,290 4,360 *4,420
18 4,020 4,090 4,180 4,250 4,310 *4,360
20 3,860 3,860 3,860 3,860 3,860 3,860 *3,860
22 3,290 3,290 3,290 3,290 3,290 3,290 3,290
24 2,820 2,820 2,820 2,820 2,820 2,820 2,820
26 2,430 2,430 2,430 2,430 2,430 2,430 2,430
28 2,100 2,100 2,100 2,100 2,100 2,100
30 1,820 1,820 1,820 1,820 1,820
32 1,580 1,580 1,580 1,580 1,580
34 1,360 1,360 1,360 1,360 NOTES:
1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 75% of tipping
36 1,110 1,110 1,110 1,110 loads on rubber in accordance with SAE J765.
38 1,000 930 930 2. 15 ft. offsettable boom extension may be used for single line lifting service only.
3. Defined Arc - Over front includes 6° on either side of longitudinal centerline of machine. Pick and carry lifting NOT
Lifting Capacity at Forty Eight Degree Boom Angle permitted.
On Rubber - 360° 4. Capacities are applicable to machines equipped with 385/65R22.5 (J) Firestone T839 tires at 140 psi cold inflation pressure.
5. Capacities are applicable only with machine on firm level surface.
Boom Main Boom Length in Feet 6. All rubber lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation
Angle 21 25 30 35 40 pressures. Damaged tires are hazardous to safe operation of crane.
7. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
2,310 1,930 1,500 1,060 770 with boom extension occurs rapidly and without advance warning.
48° **
(26.7) (29.2) (32.7) (36.3) (39.8) 8. No load stability on rubber 360° with 15 ft. offsettable extension installed at 45° offset:
Note: ( ) Ref. radii in feet. A6-829-100751A a. Minimum boom angle for 52 ft. main boom = 56°
*This capacity based on maximum boom angle. b. Maximum main boom length at 45° main boom angle = 45 ft.
** Radii are with the extension at horizontal. 9. When lifting loads the minimum allowable boom angle is 48° at 45° offset.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 19
15 FT. OFFSETTABLE EXTENSION AT 0° OFFSET
RATED LIFTING CAPACITIES IN POUNDS ON RUBBER
STATIONARY - DEFINED ARC OVER FRONT
Radius Main Boom Length in Feet
in
Feet 21 25 30 35 40 45 52
12 4,450 *4,500
14 4,280 4,350 *4,420 *4,480
16 4,140 4,210 4,290 4,360 *4,420
18 4,020 4,090 4,180 4,250 4,310 4,360
20 3,920 3,990 4,080 4,150 4,220 4,270 4,330
22 3,850 3,910 3,990 4,070 4,130 4,190 4,260
24 3,800 3,850 3,920 3,990 4,060 4,120 4,180
26 3,710 3,800 3,860 3,930 3,990 4,050 4,120
28 3,730 3,750 3,750 3,750 3,750 3,750
30 3,310 3,310 3,310 3,310 3,310
32 2,930 2,930 2,930 2,930 2,930
34 2,600 2,600 2,600 2,600
36 2,320 2,320 2,320 2,320
NOTES:
38 2,070 2,070 2,070 1. All capacities above the bold line are based on structural strength of boom extension and do not exceed 75% of tipping
loads on rubber in accordance with SAE J765.
40 1,850 1,850
2. 15 ft. offsettable boom extension may be used for single line lifting service only.
45 1,400 3. Defined Arc - Over front includes 6° on either side of longitudinal centerline of machine. Pick and carry lifting NOT
permitted.
Lifting Capacity at Forty Eight Degree Boom Angle
4. Capacities are applicable to machines equipped with 385/65R22.5 (J) Firestone T839 tires at 140 psi cold inflation pressure.
On Rubber - Defined Arc Over Front
5. Capacities are applicable only with machine on firm level surface.
Boom Main Boom Length in Feet 6. All rubber lifting depends on proper tire inflation, capacity and condition. Capacities must be reduced for lower tire inflation
Angle pressures. Damaged tires are hazardous to safe operation of crane.
21 25 30 35 40 45 52
7. WARNING: Operation of this machine with heavier loads than the capacities listed is strictly prohibited. Machine tipping
3,710 3,480 2,810 2,280 1,870 1,540 1,130 with boom extension occurs rapidly and without advance warning.
48° ** 8. No load stability on rubber (defined arc) with 15 ft. offsettable extension installed at 45° offset:
(26.7) (29.2) (32.7) (36.3) (39.8) (43.3) (48.3)
a. Minimum boom angle for 52 ft. main boom = 45°
Note: ( ) Ref. radii in feet. A6-829-100753A
* This capacity based on maximum boom angle. b. Maximum main boom length at 45° main boom angle = 52 ft.
** Radii are with the extension at horizontal. 9. When lifting loads the minimum allowable boom angle is 48° at 45° offset.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
20 GROVE YB4415/YB4415XT
LOAD DISTRIBUTION CHART FOR CARRY DECK
AREA 1
43.2 sq. ft. / 4.01 m2 13,195 lb. / 5,985 kg
AREA 2
23.1 sq. ft. / 2.15 m2 6,805 lb. / 3,087 kg
TOTAL
66.3 sq. ft. / 6.16 m2 20,000 lb. / 9,072 kg
1. Maximum travel speed with any or all loads - 2.5 MPH (4.0 km/h)
2. Loads to be transported on smooth level firm surfaces only.
3. Boom must be retracted and in center forward position.
4. Any combination or total of areas 1 & 2 may be used.
5. Lifting is not permitted when carry deck is loaded except for loading and unloading carry deck.
6. Rated pick and carry loads may be transported on deck area 1 provided the load is cribbed directly on
the frame rails.
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
GROVE YB4415/YB4415XT 21
Grove Worldwide - World Grove Asia/Pacific - Representative
Headquarters Office
Western Hemisphere, Asia/Pacific Asia/Pacific, Near East
1565 Buchanan Trail East 171 Chin Swee Road
P.O. Box 21 #10-09 San Centre
Shady Grove, Pennsylvania 17256-0021, Singapore 16987
USA Tel: [Int + 65] 536-6112
Tel: [Int + 1] (717) 597-8121 Fax: [Int + 65] 536-6119
Fax: [Int + 1] (717) 597-4062
Grove China - Representative Office
Grove Europe Limited* Room 713, Towercrest Plaza
Europe, Africa, Middle East No. 3 Mai Zi Dian West Road
(Sales & Marketing) Chao Yang District
1 Emperor Way Beijing, China 100016
Doxford International Business Park Tel: [Int + 86] (10) 64 67 16 90
Sunderland SR3 3XR, England Fax: [Int + 86] (10) 64 67 16 91
Tel: [Int + 44] (191) 515-7253
Fax: [Int + 44] (191) 564-0442 Grove Middle East
P.O. Box 290
Grove Europe Limited* Dubai, United Arab Emirates
UK & EIRE (Sales & Service) Tel: [Int + 971] (4) 3484478
Telford Road, Bicester Fax: [Int + 971] (4) 3484478
Oxfordshire OX6 0TZ, England
Tel: [Int + 44] (1869) 878-890 Lifetime Customer Support
Fax: [Int + 44] (1869) 878-891 Western Hemisphere, Asia/Pacific
1086 Wayne Avenue
Deutsche Grove GmbH Chambersburg, Pennsylvania 17201
Germany (Sales & Service) USA
Helmholtzstrasse 12, Postfach 5026 Tel: [Int + 1] (717) 263-5100
D-40750 Langenfeld, Germany Fax: [Int + 1] (717) 267-0404
Tel: [Int + 49] (2173) 8909-0
Fax: [Int + 49] (2173) 8909-30 Europe, Africa, Middle East
Grove Europe Limited*
Deutsche Grove GmbH 1 Emperor Way
Wilhelmshaven Works Doxford International Business Park
Industriegelande West, Postfach 1853 Sunderland SR3 3XR, England
D-26358 Wilhelmshaven, Germany Tel: [Int + 44] (191) 565-6281
Tel: [Int + 49] (4421) 294-0 Parts Fax: [Int + 44] (191) 515-7475
Fax: [Int + 49] (4421) 294-301 Service Fax: [Int + 44] (191) 515-7340
http://www.groveworldwide.com
Distributed By:
Constant improvement and engineering progress make it necessary that we reserve the right to make
specification, equipment, and price changes without notice. Illustrations shown may include optional
equipment and accessories and may not include all standard equipment.
GROVE® and GROVE LOGO are registered trademarks of GROVE in the U.S. and/or other countries.
Copyright© 2000 GROVE. All rights reserved.