Professional Documents
Culture Documents
COMPOSITE DECKING
PART 1 GENERAL
A. Composite Decking.
B. Accessories.
1.3 REFERENCES
1.4 SUBMITTALS
B. Product Data:
1. Manufacturer's data sheets on each product to be used.
a. Includes but not limited to:
1) Spec-Data product information sheets,
2) Catalog cut-sheets.
3) Color charts.
4) Safety Data Sheets (SDS).
5) Building code evaluation reports.
6) Sample warranty forms.
2. Preparation instructions and recommendations.
3. Storage and handling requirements and recommendations.
4. Typical installation methods.
06 73 00-1
5. Maintenance.
D. Verification Samples: Two representative units of each type, size, pattern and color.
C. Source Limitations: Provide each type of product from a single manufacturing source
to ensure uniformity.
D. Mock-Up: Construct a mock-up with actual materials in sufficient time for Architect's
review and to not delay construction progress. Locate mock-up as acceptable to
Architect and provide temporary foundations and support.
1. Intent of mock-up is to demonstrate quality of workmanship and visual
appearance.
2. If mock-up is not acceptable, rebuild mock-up until satisfactory results are
achieved.
3. Retain mock-up during construction as a standard for comparison with
completed work.
4. Do not alter or remove mock-up until work is completed or removal is
authorized.
A. Store and handle in strict compliance with manufacturer's written instructions and
recommendations.
06 73 00-2
operations.
1.9 WARRANTY
PART 2 PRODUCTS
2.1 MANUFACTURERS
A. Standards Compliance:
1. ASTMD D7032.
2. ASTM G164.
3. Density: 7.2 lb per cu ft (115.3 kg per cu m); meeting ASTM D2395.
06 73 00-3
7. Texture: Embossed wood grain one side, smooth one side.
8. Configuration: _____.
9. Configuration: As indicated on Drawings.
10. Color: Westminster Grey.
11. Color: Peruvian Teak.
12. Color: Brazilian Ipe.
13. Color: Spanish Walnut.
14. Color: Hawaiian Charcoal.
15. Color: Roman Antique.
16. Color: To be selected by Architect.
17. Finish: Matte.
18. Installation Method: Concealed fasteners and exposed composite screws.
2.4 ACCESSORlES
C. Starter Clips: SC-25 for concealed attachment of decking boards at front edges of
stair treads, exposed outside edges of decks, and butted up against vertical walls,
barriers, or penetrations.
D. End Caps: Plastic closures to cover exposed ends of Voyager Series hollow core
decking boards.
E. Fascia board: Fabricated from same material as decking boards, matching deck
board color, for covering support framework at exposed locations.
G. Hidden Fasteners.
1. Deck Screw: Cap-Tor, xd screws 10 x 2-3/4 (70 mm) long. To fasten
composite capstock decking with a clean, smooth and uniform finish.
a. Stainless Steel: Grade 305.
b. Stainless Steel: Grade 316.
c. Color: Peruvian Teak No. 34.
d. Color: Westminster Gray No. 37.
e. Color: Roman Antique No. 54.
f. Color: Hawaiian Charcoal No. 55.
g. Color: Spanish Walnut No. 71.
h. Color: Brazilian Ipe No. 73.
2. Fascia Screw: 10 x 1-7/8 inch (48 mm) long. For use with fascia boards from
1/2 to 3/4 inch (12 to 19 mm) thick.
a. Color: Peruvian Teak No. 34.
b. Color: Westminster Gray No. 37.
c. Color: Roman Antique No. 54.
d. Color: Hawaiian Charcoal No. 55.
e. Color: Spanish Walnut No. 71.
f. Color: Brazilian Ipe No. 73.
PART 3 EXECUTION
3.1 EXAMINATION
06 73 00-4
A. Do not begin installation until substrates have been properly constructed and
prepared.
3.2 PREPARATION
3.3 INSTALLATION
END OF SECTION
06 73 00-5