Professional Documents
Culture Documents
ISC Series
ISOLATED
SIGNAL
CONVERTER
SIGNAL CONVERTERS
WITH GALVANIC ISOLATION
FEMA ELECTRÓNICA
MODEL
ISC-P for Process
HT1102r150908
USER’S MANUAL info@fema.es
FEMA ELECTRÓNICA - Page 1 www.fema.es
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
1-GENERAL INFORMATION___________________________________
The ISC series of Isolated Signal Converters, The isolation offered by the ISC series of
allow to convert process signals, Isolated Signal Converters is a 3 way
temperatures, electrical signals, etc, to current isolation. Thus, all the benefits exposed
loops or voltage signals for further above are applicable to any of the three
retransmision, while introducing into the circuits composing the instrument : input,
system galvanic isolation barriers between output and power.
the input, the output and the power supply
circuits. Recalibration of the instruments is realized
in a fast and easy way. Opening the front
The ISC series of Isolated Signal Converters, cover grants access to the configuration
offer an excellent relation between signal jumpers. Additional Span and Offset
conversion speed and measurement potentiometers are directly accessible from
accuracy. Offering a 0.2% accuracy and up the frontal part. These potentiometers are
to a 70ms response time depending on the highly decoupled, minimizing the iterations
model, these units can process information needed to obtain a correct adjustment.
coming from probes or transducers, in such
a way that can be quickly retransmitted in a In order to obtain a higher and quickest
fast and accurate form to remote data benefit of the ISC units, we recommend you
acquisition systems or PLC’s. The isolated to read carefully the information provided in
signal converters of the ISC series are ideal this manual before proceeding to the
to integrate into 12 bit data acquisition installation of the instrument. In this manual
systems. you will find all technical data, both electrical
and mechanical, needed for a correct
Its powerful galvanic isolation of 3.500 V instalation and utilization.
introduces high security to the measuring
systems, preventing the propagation of those Note : The ISC Isolated Signal Converter
phenomenon which usually cause damage instruments have a characteristics label
to the remote system, such as transient attached on the side of the instrument. Check
peaks or energy shocks in any of the circuits that the information indicated on the label
of the system. The galvanic isolation also matches with your application requirements,
acts as a strong CE barrier. The decoupling and specially check that the value and type of
created between the input, output and power the power supply needed matches the value
circuits avoids pernicious effects on the and type of the power supply availble on your
output, such as ground loops or signal leaks, installation.
which distort the acquired data and are
extremely difficult to isolate once introduced
into the signal.
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
2-INSTALLATION____________________________________________
Before installing the instrument check the The instrument must be installed in such a
characteristics label attached to the side of way that it remains in vertical position as
the unit. Specially check that the value of indicated on Figure4.
the power supply needed, matches the power
supply available on your installation. To help dissipate the heat, a free space of
2mm must be left available on both sides of
The characteristics label also indicates the the instrument.
input/output signal relation for the instrument.
Remember to take note of the new input/
output relation if you proceed to readjust the
instrument.
J1
J2
OUTPUT JUMPERS 2 mm
J3 FIGURE 4
J4
J5
J6
POT. SPAN
POT. OFFSET
J7
J8
J9
J10
J11
J12 INPUT JUMPERS
FIGURE 1 FIGURE 2
FIGURE 3
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
Input Connections
321
93mm
110 mm (3.66’’)
(4.33’’)
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
The position of the input jumpers selects the To change the input/output relation of the
range for the input signal as indicated below. instrument, proceed as indicated below :
J8
3.- Select the required output jumpers (Section
J9
5, page 6)
J10
J11 4.- Connect a signal generator to the input
J12 terminals (8 signal and 9 common)
The position of the output jumpers selects 8.- Repeat 6 and 7 to improve the accuracy
the range for the output signal as indicated until it reaches its specified value
below.
9.- Close the front cover
4/20 mA
0/20 mA 0/10 VDC 0/1 VDC
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
Input Range select the input range [IR] from the following options
20mA, 50mA, 5mA , 10Vdc, 1Vdc
Output Range select the output range [OR] from the following options
10Vdc, 20mA, 1Vdc
SPAN Value
[IR] x [OH] - [OL]
SPAN =
[IH] - [IL] [OR]
OFFSET Value
[OL] [IL]
OFFSET = - x SPAN
[OR] [IR]
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com
Datasheet
Signed : D.Juncà
Quality Manager
Barberà del Vallès, 2002
Sales: +44 (0) 1273 570 220 Website: www.amplicon.com Email: sales@amplicon.com