Belotram Corperaten Phone: 30467-1200
Route 2, Box 305, Newel, WY 26050, USA Fax 3087887-1212
PRODUCT INSTRUCTIONS
Type 70 Pressure Regulator
INSTALLATION:
The Bellofram high-flow Type 70 is designed for air service only. The maximum supply pressure is 250 PSI
Clean all pipe lines to remove dir and scale before installation is made. Apply minimum amount of pipe
compound to the male threads of the air line only. Install regulator in air line; body is fitted with a 1/4", 3/8" or 1/2"
NPT for inlet and outlet connections. ‘The words “IN" and "OUT" are cast into the body to indicate the direction of
flow. Regulator can be mounted in any position without affecting the operation. Avoid undersized fitings that will
limit the flow through the regulator and cause pressure drop downstream, ‘The use of a filter to remove dit and
liquid inthe air line ahead of the regulator is recommended for best performance. If an air line lubricator is used,
‘it should be located downstream beyond the regulator in order to avoid interference with the regulator
performance.
OPERATION:
The Type 70 is a high capacity regulator that provides a uniform output pressure independent of supply pressure
variations.
Before putting the regulator into service for the first time, relieve pressure pn the range spring by turning the knob
counterclockwise. To operate, turn the pressure adjusting knob slowly Jn a clockwise direction until required
downstream pressure is obtained. Tumed in this direction, the range spring compresses causing increased output
pressure,
MAINTENANC!
‘The regulator is easily disassembled for the occasional cleaning or removal of foreign matter. Before this is done,
however, shut off vaive upstream of the regulator to prevent escape of air when regulator is disassembled, There
Js no need to remove the regulator from the pipe line; remove the two 8-32 screws on the bottom of the unit and
pull out the pintle assembly, Wash the inner valve assembly with solvent exercising care to avold damaging
diaphragms and vaive facings. (Avoid such solvents as acetone, carbon tet, tichiorethiene.) Replace assembly
carefully,
The vent hole in the bonnet should be kept clear, A slight flow of air through this hole is necessary for proper
operation of the regulator.
TO INSTALL REPLACEMENT PARTS:
1. Order repair kit. See back of this sheet,
2. Shut off air supply.
3. To replace “O”-ting and pintle assemly, see disassembly instructions above under “Maintenance*
4, To replace diaphragm assembly.
a. Remove knob assembly, (6) 8-32 screws securing bonnet, guide, range spring and diaphragm
assembly.
b. Install diaphragm assembly and other parts in reverse order. Be sure to align bonnet vent hole with
the “IN” port
Warranties of Sale, disclaimer thereof and limitations of liability are covered exclusively by Bellofram’s printed warranty statement for
the cylinders, These instructions do not expand, reduce, modify of alter Bellofram’s warranty statement and no warranty or remedy in
favor of a customer or any other person arises out of these instructions.
Belotram Corporation Product Instructions No. S41-000-040 Revision O Page of26 hone: 204/887-1200
enc WY 26060, USA Fee 30487-1252
—<
iTeM PART NUMBER ary. DESCRIPTION
218-630-000-004 1___[ Knob Assembi
214-648-000-145 6 | 8-32 X 7/6" Screws
214-684-000-054 4__| 5116-24 Nut
1} (Order entire Pressure Regulator)
‘214-626-000-026 4
216-643-000-072 + | Spring Guide 2-150 PSIG.
'214-655-000-132 [Range Spring 0-30 PSIG
214-655-000-131 1__| Range Spring 1-60 PSIG
214-655-000-133 1 [ Range Spring 2-150 PSIG
'222-804-000-023 1__[* Diaphragm Assembly
212-814-000-005 {| Baffle Assembly
'214-649-000-201 + [o"-Ring
10 |__214-626-000-027 1___| Lower Baffle Guide
“| 212-650-000-018 1 [Seat Assembly
214-647-000-005 1 __| Soreen
'242-813-000-003 |" Pintle Assembly
214-638-000-016 1 | Bottom Plate
za 2 3/6" FH, Screws
* Denotes parts more commonly replaced and included in repair kit
‘Kit PIN 201-970-127-000
IMPORTANT: Orders for hese parts cannot be propery filed unless you specify the regulator part number and pressure
range
Beltar Corporation Product instructions No Ss1-00004 Revision D Pago 2012