Professional Documents
Culture Documents
500 mm
(19.7 in)
276 mm 184.8 mm
(10.9 in) (7.3 in)
External interfaces Weight = 20.7 kg
Important! (bottom of RRH) (45.6 lbs)
The Nokia B65a RRH2x40-4R must be installed vertically oriented with cabling Notes:
interfaces at the top and bottom. Upside down and horizontal mounting are not
1. All specifications are with the mounting bracket installed.
allowed.
2. Dimensions do not include connectors or other small protrusions.
The B65a RRH2x40-4R may also be referred to as UHGC.
Intended audience
This document is intended for field construction personnel during the installation of hardware for Nokia customers. This product must only be installed
by a Qualified Person (a person designated by the employer; and by reason of training, experience, or instruction has demonstrated the ability to
perform safely all assigned duties; and, when required is properly licensed in accordance with federal, state, or local laws and regulations). Proper safety
polices and practices must be adhered to. Risks are discussed in more detail in the LTE B65a RRH2x40-4R - Site Preparation Guidelines (3MN-01909-
0001-RJZZA) and LTE Remote Radio Head (RRH) - Safety Guidelines (3MN-01725-0002-RJZZA) documents available to Nokia customers at
http://support.alcatel-lucent.com/. No other use of this document is approved.
Legal notice
Nokia is a registered trademark of Nokia Corporation. Other products and company names mentioned herein may be trademarks or tradenames of their respective owners.
The information presented is subject to change without notice. No responsibility is assumed for inaccuracies contained herein.
© 2017 Nokia. All rights reserved.
Contains proprietary/trade secret information which is the property of Nokia and must not be made available to, or copied or used by anyone outside Nokia without its written authorization.
Not to be used or disclosed except in accordance with applicable agreements.
Required parts
Part No. 3JR10178AA Part No. 3JR58710AA
Qty. 1 Qty. 1
Comments Includes RRH with carrying Comments Optional: Required only for
handle small pole mounting
Qty. 1 Qty. 1
Comments Optional: 1 per RRH; includes Comments Optional: Required only for large
fasteners pole mounting
Description RRH mounting bracket Description Ground cable with simple lug,
16 mm² (6 AWG), 8 m
Qty. 1 Qty. 1
Comments 1 required per RRH; used for all Comments 1 required per RRH for
mounting methods protective earth (PE) ground
Description RRH 4*Tx/Rx basic installation Includes cable ties, wire ferrules, Description 7/16 DIN 10 W load terminator
kit 2-hole lugs, heat shrink material,
waterproof tape, vinyl electrical
Qty. 1 tape, and cable labels Qty. 2 or 0 (optional)
Comments 1 required per three RRHs Comments Required for unused RF ports
Qty. 1
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 2 of 18
Required parts (continued)
Part No. 1AB416150001 Part No. Part number depends on length
required and connector type
Description SFP transceiver, SMDF, Rate 3 Description RF cable, coax, 7/16 DIN male
to 7, 1310 nm, 14 km, LC conn. Includes coaxial cable with 7/16
DIN male connectors
Qty. 1 Qty. 2 or 4
Comments 1 required per CPRI connection Comments 1 required for each antenna
connection used
Part No. Part number depends on length Part No. Part number depends on length
Description Optical fiber, SMDF, LC-LC Description User alarm cable, 4 pair, circular
connectors DIN male on one end
Qty. 1 Qty. 1 (optional)
Comments 1 required per CPRI connection Comments Required for user alarms
Description R2CT weatherized plug Description AISG cable, 8-pin circular DIN
Qty. 1 Qty. 1 (optional)
Comments 1 required per CPRI connection Comments Required for AISG daisy chain
connection
Description Cable adaptor assembly kit, Description Cable adaptor assembly kit,
2x6 mm² to 2x10 mm² 2x6 mm² to 2x16 mm²
Qty. 1 (optional) Qty. 1 (optional)
Comments 1 required per RRH for use with Comments 1 required per RRH for use with
3BK50119AB only 1AC05801001 only
Part No. Mutually exclusive part number depends on 3BK50201AA = 2x4 mm² (12 AWG), 250 m roll, used for length > 0 m
length required and conductor size and ≤ 28 m
3BK50113AC = 2x6 mm² (10 AWG), 250 m roll, used for length
Description Power cable, 250 m roll or ordered to length
> 28 m and ≤ 56 m
Qty. 1 3BK50119AB = 2x10 mm² (8 AWG), 250 m roll, used for length > 56 m
and ≤ 93 m
Comments 250 m roll = 1 required per multiple RRHs;
ordered to length = 1 per RRH 1AC05801001 = 2x16 mm² (6 AWG), ordered to length, used for
length > 93 m and ≤ 153 m
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 3 of 18
External interfaces
CPRI₋PRI
GND
Note: Solar shield and wall mounting bracket not shown in these views
Attention: For all product-specific figures in this document, the colors depicted are for identification purposes only. Final product colors may be different.
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 4 of 18
1: Unpack RRH & prepare for installation
Required materials
Important! The remote radio head (RRH) must be 3JR10825AA RRH mounting bracket 1
handled with care during unpacking and staging. 3JR39511AA Solar shield (optional) 1
1 Open shipping box and carefully roll RRH onto left (See note 1)
Carrying handle
RRH
Hoisting
mounting
points
bracket
Top of
2 Carefully lift RRH out of box.
RRH
Bottom view
RRH solar
shield
Bottom
of RRH
DANGER
Electric shock hazard
Working in severe weather can result in personal injury or death and damage to the equipment.
Never install or perform maintenance during severe weather (high winds, lightning, blizzards, hurricane etc.).
WARNING
Falling-object hazard
If the B65a RRH2x40-4R falls while being lifted, it can result in personal injury or death and damage to the equipment.
Keep the area beneath the B65a RRH2x40-4R and the immediate surrounding area completely clear of personnel,
equipment, vehicles, etc. at all times during the lifting and moving operation.
WARNING
Overhead-load hazard
Hoisting points and apparatus can break, severely damaging the B65a RRH2x40-4R when it is being lifted to its final
mounting position.
Ensure that all hoisting points and lifting apparatus are defect free and properly attached before lifting the B65a
RRH2x40-4R.
WARNING
Fall hazard
Falls can occur when working at heights resulting in serious personal injury or death.
To prevent a fall when working at heights (ladder, scaffold, manlift, roof, etc.) follow safe work practices and wear
appropriate fall protection equipment.
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 7 of 18
Safety statements for installation procedures (continued)
Note: For the complete set of product safety statements, see LTE Remote Radio Head (RRH) - Safety Guidelines, 3MN-01725-
0002-RJZZA, available at http://support.alcatel-lucent.com/.
CAUTION
Lifting hazard
Lifting this equipment by yourself can result in injury due to the size and weight of the equipment.
Always use at least two people or a lifting device to move or position this equipment.
CAUTION
Laceration hazard
The mounting bracket components may have sharp edges and burrs and contact may cause cuts and lacerations.
Beware of sharp edges and burrs, especially when manually transporting or hoisting the B65a RRH2x40-4R.
Wear appropriate personal protective equipment.
CAUTION
RF hazard
RF exposure in excess of applicable limits can result in personal injury.
The B65a RRH2x40-4Rs are designed and installed in order that they are compliant with the exposure guidelines laid
down by 47 CFR 1.1307 to 1.1310.
For all staff that are required to work in close proximity to the equipment, for example maintenance personnel, contact
with the antenna should be avoided. No such persons shall stay in front of the operating product’s antenna at a
distance of less than 1.7 m and 0.6 m on each side of the antenna.
No other persons shall stay in front of the operating product’s antenna at a distance of less than 4.1 m and 1.6 m on
each side of the antenna.
Workers equipped with personal medical electronic devices, such as pacemakers and hearing aids, shall consult the
manufacturer's instructions and consult their occupational health practitioner.
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 8 of 18
2: Install RRH on a wall
Required materials
RRH
RRH mounting
bracket
1 If necessary, attach
RRH mounting
bracket to RRH
using M8 fasteners Pole mounting
provided with RRH. bracket
RRH
RRH mounting
bracket
1 If necessary, attach
RRH mounting
bracket to RRH 2 Attach pole
using M8 fasteners mounting
provided with RRH. brackets to pole.
M8
screws
M12 bolt
hardware
M8
screws
RRH
RRH mounting
bracket
1 If necessary, attach
RRH mounting
bracket to RRH 2 Attach pole
using M8 fasteners mounting
provided with RRH. bracket to pole.
M8
screws
Band clamps
M8
screws
1 Crimp 16 mm2 (6 AWG) two-hole lug (from the 3JR57909AA Ground cable with simple lug 1
Connect to
ground system
DANGER
Laser hazard
This equipment operates with invisible laser radiation. Laser
radiation can cause considerable injuries to the eyes.
Never look into the end of an exposed fiber or into an open
optical connector when the optical source is switched on.
CPRI₋PRI
NOTICE
Protect fiber cable
1 If necessary, insert SFP into CPRI₋PRI Mishandling fiber optic cable can result in damaged and non-
port and lock into place. functioning cables.
The optical cable is very sensitive, take the maximum
Note: Clean and inspect the LC connectors precaution when installing it. The optical fiber should be
on the CPRI fiber optic cable before protected in solid pipe. Do not use cable ties on the fiber
connecting to SFP. cable. Do not cut this cable on site, excess length should be
R2CT coupling nut coiled inside the eNodeB. The fiber optic connector should be
protected by a cap when not being used. Respect the bending
2 Use assembly instructions provided with R2CT radius during the manipulation of optical cable (82.5 mm).
weatherized plug to assemble R2CT plug onto
optical fiber and connect to CPRI₋PRI port. See LTE Remote Radio Head (RRH) - Safety Guidelines, 3MN-01725-
0002-RJZZA, available at http://support.alcatel-lucent.com/.
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 13 of 18
7: Connect user alarm & AISG cables
Required materials
4 OR User_ALM_2_RTN BL = Blue
8 BL User_ALM_1_RTN WH = White
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 14 of 18
8: Connect RF cables
Required materials
Notes:
Top view Wall or pole side
1. Depends on length and connector type
2. Required for unused RF ports
Supported RF configurations
TxRx2
TxRx1
Configuration Antenna connections
Rx4
Rx3
2T2R TxRx1, TxRx2
2T4R TxRx1, TxRx2, Rx3, Rx4
Front
side 1 If required, attach 7/16 DIN connector to each RF cable.
OR OR
RF RF
2 Connect RF cables to RF ports.
cable RF load cable RF load Note: The TxRx1 and TxRx2 ports each include an
terminator terminator
integrated (internal) bias tee.
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 16 of 18
10: Connect DC power cable
Required materials
−48V IN
3 Route DC power cable through M25 cap, sealing insert, Conduit box with External view
and cable gland to DC terminal block inside conduit box. access door open when complete
6 Assemble sealing insert and M25 cap into cable gland and tighten.
Ensure sealing insert and connected DC wires do not twist.
7 Secure cable clamp inside conduit box. Close the access door and M5 torque: 4 N·m (3 lbf-ft)
tighten M5 securing screws. M25 cap torque (max): 15 N·m (11 lbf-ft)
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 17 of 18
General status LED states
Off LED disabled or no power supplied LED is disabled in software or no DC power to RRH
Solid red Initial power on RRH is initializing (if just powered on or reset)
Non-recoverable critical failure A critical hardware failure prevents the transmit and/or active receive paths from functioning
Non-critical non-recoverable failure Non-critical fault (other than antenna) detected, fault is not recoverable, RF transmission is still ON
Flashing red Recoverable critical failure RRH not currently operational due to hardware fault, but should recover (e.g., under-temperature
warm up, over-temperature critical shutdown)
External power supply failure A recoverable fault is detected and the external connections (power, antenna) should be checked
Non-critical recoverable failure Non-critical fault (other than antenna) detected, fault is recoverable, RF transmission is still ON
Flashing yellow Software download RRH is downloading software and RF transmission is OFF, but is currently operational
Solid yellow Slave CPRI link failure The slave CPRI link (CPRI1) has failed
Flashing green Standby No critical failures or faults, but the transmitter is disabled
Bottom view
Status LED
B65a RRH2x40-4R (UHGC) Nokia – Proprietary – Use pursuant to applicable agreements 3MN-01909-0002-RJZZA Issue 02 October 2017 Page 18 of 18