Professional Documents
Culture Documents
1.940 1.940
[49.28] [49.28]
IAL/IUL/IEL/LEL
.142 .375
[3.61] [9.53]
.392
[9.96]
.592
[15.04]
Notes:
Tolerance ± .015 [.39] unless noted. Bullet terminal receptacle should be .312
Dimensions in brackets [ ] are millimeters. ± .001 diameter hole not less than .250
A Terminal protrusion dimensions are referenced from back of mounting panel. depth. Contact Airpax for other bullet
B Each screw terminal is supplied with a 10-32x.312 [7.92] or M5 x 8mm screw, sizes.
flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher
and a 10-32 or M5 hex nut (<=70A) (<=50A for LEL),1/4-20 or M6 hex nut
(>70A)(>50A for LEL).
Multi-pole units are combined in an assembly with the trip mechanisms internally Two Pole Units
coupled. A fault in any protected circuit opens all poles simultaneously. Applications An assembly consisting of two single pole units, having their trip mechanisms
include use in polyphase circuits, single-phase three-wire systems, or in two or internally coupled, is available with either a single toggle handle or with a handle
more related but electrically isolated circuits. A mix of delays, ratings and per pole. Please see decision one of the part number decision tables. Individual
configurations are offered. The auxiliary switch is offered with either gold or silver poles may vary in ratings, delays and internal configurations. If the poles are of
contacts and is available when a series construction pole is specified. series construction, an auxiliary switch may be included in either or both poles,
allowing you to mix SELV and hazardous voltages.
(SEE TABLE)
4X 6-32 THREAD
.281 .140 [3.56] DEEP
[7.14] .140 .402 .220 M3 ISO THD. OPTIONAL
(SEE TABLE) [3.56] [10.21] [5.59]
ON
1.438
1.940
[49.28] [36.53]
2.060
.142 [52.32]
[3.61] OFF
1.515 1.515
.690 2.490 [38.48] [38.48]
1.859 MAX.
[47.22] [17.53] [63.24] MAX.
Note:
Tolerance ± .015 [.38] unless noted. Dimensions in
brackets [ ] are millimeters.
1.530
M6 .510 .652 [38.86]
4X Ø .156
[3.96]
1/4 - 20 .545 .687
M5 .510 .652
Note:
Each outer terminal is supplied with a flatwasher, tooth lockwasher
IAL/IUL/IEL/LEL
Note:
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312 [7.92] or M5 x 8mm screw, flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and a 10-32 or M5 hex nut (<=70A), 1/4 -20 or M6 hex nut (>70A).
.768
[19.49]
1.395
[35.43]
2.490 MAX.
.750 [63.25]
2.265 [19.05] .750
[57.53] [19.05]
MAX.
.314
[7.98]
.750 MAX.
.750 [19.05] ON
ON I
[19.05] I
2.265 .750
[57.53] [19.05] O O
IEL1111
1.530
[38.86]
ON
OPTIONAL ON I
GUARD I
.750
[19.05]
HANDLE HANDLE
POSITION "OFF" POSITION "ON"
3.015 GUARD WITH NO ACTUATE GUARD WITH NO ACTUATE
[76.58] .750 .750 OFF FEATURE OFF FEATURE
[19.05] [19.05] (SIXTH DECISION, X) (SIXTH DECISION, X)
MAX.
.750
[19.05]
1.660
[42.16]
1.260
[32.00] IAL/IUL/IEL/LEL
Four Pole Mounting Detail*
IELH1111 ON
ON
I
I
3.030 2X ÿ.156 .200
[76.96] [3.96] [5.08]
O
OFF
O
OFF
HANDLE HANDLE
Panel Mounting Detail POSITION "OFF" POSITION "ON"
WITHOUT GUARD WITHOUT GUARD
Mounting Detail Tolerance:
±.005 [.13] unless noted DETAIL "A"
NOTE: ACCESS IS LIMITED TO A DEVICE SMALLER THAN THE
UNDERWRITERS LABORATORY "ARTICULATED PROBE"
3.015 DEFINED IN UL-489 FIG. 11.1.7.2.1.
[76.58] .750 .750
MAX. [19.05] [19.05]
.750
[19.05]
Note:
Tolerance ± .015 [.39] unless noted. Dimensions in brackets [ ] are millimeters.
*See Single Pole Mounting Detail for Hole Sizes and Locations.
IAL/IUL/IEL/LEL BX Style Circuit Protectors 141
LELHP/CELHP MAGNETIC CIRCUIT PROTECTOR
The Airpax LELHP/CELHP high current magnetic circuit protector compliments our entire series of
LEL circuit protectors. Its unique, parallel current sensing design provides precise current over-
load protection and reliability in the compact size of a two pole LEL. The unit is ideal for high
power DC applications such as drive motor systems and telecommunication power systems.
It is available in series and series with auxiliary switch configurations with a choice of delays
for DC ratings of 125, 150, 175 and 200 amperes. The LELHP is UL listed under the conditions of
UL489 and CSA certified. The CELHP is UL listed under the conditions of UL489A. Mid-trip han-
dle indication, voltage trip and remote operator options complete the LELHP/CELHP circuit
breaker series. Please see the individual product tables for approved ratings.
Contact Airpax for specific part number.
Two Pole
1.515 MAX
.687 [38.48]
[17.45] .740 2X 6-32 THREAD
.140 [3.56] DEEP
.281 [18.80]
.545 M3 ISO THD OPTIONAL .220
[7.14] .140 (Note E) .402
[13.84] [5.59]
[3.56] [10.21]
.640 ON
[16.26] 2.490
1.047
[26.59] [63.25]
1.438 2.060
[36.53] [52.32]
1.940
[49.28]
1.282 OFF
[32.56]
.402 .402
NO [10.21] [10.21]
NC
BREAKER IN
OFF POSITION
OFF OFF OFF OFF OFF OFF
1.438 1.438
[36.53] [36.53] 2.060 2.060
[52.32] [52.32]
2.490 2.490
[63.25] [63.25]
-REC4 175/200 Parallel Pole
IAL/IUL/IEL/LEL
.110
[2.79]
2.438 MAX 2.265MAX.
2.265MAX.
[61.93] [57.53] [57.53]
(SEE NOTE 1) 6X 6-326XTHREAD
6-32 THREAD
.140 [3.56]
.140DEEP
[3.56] DEEP
M3 ISOM3 THDISOOPTIONAL
THD OPTIONAL
.260
[6.60] Notes:
Tolerance ± .015 [.39] unless noted. Dimensions in brackets [ ] are millimeters.
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw, flatwasher and external tooth
lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and a 10-32 or M5 hex nut
(<=70A), 1/4 -20 or M6 hex nut (>70A).
D Units are supplied without bus bars must have a minimum copper strap (1 31/32 x 1/2 x 1/16 ) of appropri-
ate length to accommodate connections tying each set of terminals together.
E Other spacing available upon request. Contact factory for assistance.
142 LELHP/CELHP Magnetic Circuit Protectors
IALN/IULN PANEL SEAL CIRCUIT PROTECTORS
The lALN/IULN family is a sealed toggle version of the IAL/IUL family. The silicone rub-
ber seal around the handle assures panel seal integrity and makes this style a natural for
harsh environments. .130
[3.30] 6-32 MTG. SCREW
This sealed toggle family is available in one to three pole models with ratings of .050 FOR HIGH SHOCK
MTG.
to 100 amperes.
LOCKWASHER
ON
OFF
.142 2.040
[3.61] [51.82] .625 .750
[15.88] [19.05]
KEYWAY
.060 [1.52]-.065 [1.65] WIDE
.030 [.76]-.035 [.89] DEEP
1.515 2.265
.750 [38.48] [57.53]
[19.05] MAX. MAX.
1.375
[34.92]
2.490
[63.25]
.656
[16.66]
(OPTIONAL, HANDLE
(Optional
MAY BEhandle
IN POLEmay
2 be in
pole 2 instead
INSTEAD OF POLE 1)
of pole 1.)
IAL/IUL/IEL/LEL
Optional handle *See Single Pole Mounting Detail for Hole Sizes and Locations.
Notes:
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw, flatwasher and external tooth lockwasher.
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and a 10-32 or M5 hex nut (<=70A), 1/4 -20 or M6 hex nut (>70A).
[3.61]
2.249 .419
[57.12] [10.65]
Single Pole
Panel Mounting Detail*
2X 6-32 THD. (TYP.)
M3 ISO THD. Two Pole Three Pole Four Pole Single,Two & Three Pole Four Pole**
OPTIONAL
.750
[19.05] 1.510
[38.35]
2.361
1.972
[50.09]
ON ON ON ON
ON 1.660
[42.16] 1.260
OFF OFF OFF OFF [32.00] 1.260
[32.00]
OFF 1.660
[42.17]
1.859
[47.22] .201 .750 MAX.
[5.11] [19.05]
.772
IALZX/IULZX/IELZX Rocker Handle Styles [19.62]
1.395
The IALZX/IULZX/IELZX style adds our rocker handle options of contrasting dual Available
[35.43]with a black rocker and white, red or green indicator color for either ON or
color rocker actuators, affording a clear visual indication of the handle position and
2.490 MAX.
[63.25]
OFF indication. ON 1.660
[42.16]
integrated handle guards, to help prevent accidental turn-on and turn-off of the unit.
OFF
OPTIONAL
HANDLE GUARDS
1.239
[31.47]
.314 .506
[7.98] [12.85] 2X 6-32 THD.
M3 ISO THD.
OPTIONAL
.772
[19.62] .750
[19.05]
1.395
[35.43]
2.490 MAX.
[63.25] ON 1.660
[42.16] 1.660
Panel Mounting Details [42.17] 1.260
OFF
Mounting Detail Tolerance: [32.00]
OPTIONAL
±.005 [.13] Unless Noted.
HANDLE GUARDS
1.239
[31.47]
.314 .506 2X Ø .156 .200
[7.98] [12.85] 2X 6-32 THD. [3.96] [5.08]
M3 ISO THD.
OPTIONAL
1.660
Panel Mounting Details [42.17] 1.260
IAL/IUL/IEL CONFIGURATIONS
trip where the sensing coil and contacts are in series with the load
being protected. The handle position conveniently indicates circuit
status. In addition to providing conventional overcurrent protection, 1.940
SERIES SWITCH ONLY
[49.28]
it’s simultaneously used as an on-off switch.
Shunt Trip
Dimension A
The shunt trip is designed for controlling two separate loads with (See Table)
open and remove power from both loads simultaneously. The total [16.46]
C
current rating of both loads must not exceed the maximum contact NO
NC
rating. 1.290
1.055
[26.80]
[32.77] BREAKER IN OFF POSITION
Dual Coil
By combining two electrically independent coils on a common mag-
netic circuit, it is possible to provide contact opening when either an
over-current or trip voltage is applied to the respective coils. One
coil will be a current trip coil with standard specifications. The sec- M6 .510 .652
ond, or dual coil, can be used to provide a control function 1/4 - 20 .545 .687
permitting contact opening from a remote interlock or other trans- M5 .510 .652
ducer functions. Standard coils are 6, 12, 24, 48, 120 and 240 volts.
10 - 32 .545 .687
Tripping is instantaneous and must be removed (usually self-inter-
Screw stud Dim. “A” Dim. “B”
rupting) after trip. thread (± .045) (± .035)
[49.28]
ratings below 6Vac or 5Vdc, an auxiliary switch with gold contacts,
designated as REG is available. Gold contacts are not recommended
for load current above 100 milliamps.
.795
[20.19]
2.640 MAX.
[67.06]
(SEE NOTE A)
IAL/IUL/IEL/LEL
SHUNT DUAL COIL
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw, flat- 1.266
.250
[6.35]
[32.16]
washer and external tooth lockwasher. -IREC5
-IREC4, -IRE
C Stud terminals are supplied with a flatwasher, external tooth lock washer and a 10-32 2.454 MAX.
or M5 hex nut (<=70A), 1/4-20 or M6 hex nut (>70A). .187
[4.75]
[64.52]
(SEE NOTE A) .110
2.438 MAX.
[64.52]
[2.79] (SEE NOTE A)
.250 .260
[6.35] [6.60]
-IREC5
-IREC4, -IREG4
FIG.3 FIG.4
.795
Relay and Dual Coil [20.19]
.660±.045
[16.76±1.14]
.281
[7.14]
.722
[18.34]
1.330
1.147
[33.78] 1.147
[29.13]
[29.13]
.721 .721 .033
1.940 [18.31]
.033
[18.31] [.84]
[.84]
[49.28]
(SEE NOTE A)
NOTE:
THIS BARRIER CAN BE FLIPPED
TO COVER EITHER POLE.
RELAY
RELAY DUAL
DUAL COIL
COIL PLEASE CONTACT FACTORY FOR
SPECIFIC PART NUMBER
Notes:
Rating Standard Optional
Tolerance ± .015 [.39] unless noted. Dimensions in brackets [ ] are millimeters.
Option Barrier Barrier
A Terminal protrusion dimensions are referenced from back of mounting panel.
B Each screw terminal is supplied with a 10-32x.312[7.92] or M5 x 8mm screw, flatwasher and
external tooth lockwasher. IEL
C Stud terminals are supplied with a flatwasher, external tooth lockwasher and a 10-32 or M5 hex
Fig. 1
IAL/IUL/IEL/LEL
nut (<=70A), 1/4 -20 or M6 hex nut (>70A). 240/415Vac Fig. 2,3 & 4
415V (VDE)
277/480Vac
1/4-20, M6 studs for AC
120/240Vac multi-pole Fig. 2 Fig. 3 & 4
125Vdc
LEL
All multi-pole 50/60Hz Fig. 2 Fig. 3 & 4
All multi-pole 80Vdc if opposite polarity Fig. 2 Fig. 3 & 4
125Vdc Fig. 2 Fig. 3 & 4
1.560
[39.62]
IAL/IUL/IEL/LEL
The Airpax Remote Operated Circuit Breaker (ROCB) provides the convenience of remote power
disconnect and reset capability with the safety and accuracy of a magnetic current sensing Note: Stud terminal style shown.
device. It allows the operation of the circuit breaker from various locations in the system, facility REMOTE .140
OPERATOR [3.56]
CONNECTOR
or site, while not sacrificing the ability to manually operate the breaker if required. Service, diag-
nostics, load shedding and power distribution control functions can now be performed in areas
that were previously unattended, inaccessible or unsafe. ON
Based on our popular IEL/LEL circuit protector series, the ROCB shares the same dimen- PLUG A
1 3
1.940
sional characteristics (maximum three poles plus the remote operator) for easy adaptation [49.28]
into existing panel designs, yet its compact size allows efficient use of space for new design
2 4
CONNECTOR
OFF
applications. In addition, the ROCB has been designed to meet the requirements of domestic
and international agency standards for motor operated circuit protection, ensuring worldwide
component acceptance. .281 1.859 .690
POLE 1 POLE 2 [7.14] [47.22] [17.53]
Contact Airpax for specific part number. .142
[3.61]
W
SEVERE ELECTRIC
S H OCK HAZARD
[36.53]
W W
A A
A
R R
R
N N
N
I I
2.060 N N
G
I
N
[52.32]
G G
0 WE R 0 WE R
EA K E R 0 WE R
EA K E R
B E F O R E C ON T A C T EA K E R
B E F O R E C ON T A C T
W ITH LOAD. W ITH LOAD. B E F O R E C ON T A C T
W ITH LOAD.
2.490
[63.24]
1.515 2.265
[38.48] [57.53] 3.015
MAX. MAX. [76.58]
MAX.
1.448
[36.78] 2.060
[52.32]
IAL/IUL/IEL/LEL
41* No trip May trip .5 - 8 .15 - 1.9 .02 - .4 .006 - .25 .004 - .1 .004 - .05
42* No trip May trip 5 - 70 2.2 - 25 .40 - 5 .012 - 2 .006 - .2 .006 - .15
43* No trip May trip 35 - 350 12 - 20 1.5 - 20 .012 - 2.2 .01 - .22 .01 - .1
49* No trip May trip .100 max. .050 max. .020 max. .020 max. .020 max. .020 max.
51 No trip .5-6.5 .3 - 3 .1- 1.2 .031 - 5 .011 - .25 .004 - .1 .004 - .08
59 No trip .120 max. .100 max. .050 max. .022 max. .017 max. .017 max. .017 max.
69 No trip .120 max .100 max. .050 max. .022 max. .017 max. .017 max. .017 max
10000 10000
10000 10000
MAY TRIP
100 100
MAY TRIP
MAY TRIP
100 100
TIME IN SECONDS
TIME IN SECONDS
TIME IN SECONDS
TIME IN SECONDS
10 10 10 10
1 1 1 1
.1 .1 .1 .1
MAY TRIP
MAY TRIP
IAL/IUL/IEL/LEL
TIME IN SECONDS
TIME IN SECONDS
TIME IN SECONDS
TIME IN SECONDS
10 10 10 10
1 1 1 1
.1 .1 .1 .1
10000 10000
MAY TRIP
1000 DELAY 51 1000 DELAY 53
MAY TRIP
100 100
TIME IN SECONDS
TIME IN SECONDS
10 10
1 1
.1 .1
.01 .01
.001 .001
0 100 150 200 300 400 500 600 700 800 900 1000 0 100 150 200 300 400 500 600 700 800 900 1000
125 125
PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT
10000 10000
100 100
MAY TRIP
IAL/IUL/IEL/LEL
TIME IN SECONDS
TIME IN SECONDS
10 10
1 1
.1 .1
.01 .01
.001 .001
0 100 150 200 300 400 500 600 700 800 900 1000 0 100 150 200 300 400 500 600 700 800 900 1000
125 125
PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT
10000 10000
MAY TRIP
1000 DELAY 41 1000 DELAY 43
MAY TRIP
100 100
TIME IN SECONDS
TIME IN SECONDS
10 10
1 1
.1 .1
.01 .01
.001 .001
0 100 150 200 300 400 500 600 700 800 900 1000 0 100 150 200 300 400 500 600 700 800 900 1000
125 125
PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT
10000 10000
100 100
MAY TRIP
TIME IN SECONDS
TIME IN SECONDS
IAL/IUL/IEL/LEL
10 10
1 1
.1 .1
.01 .01
.001 .001
0 100 150 200 300 400 500 600 700 800 900 1000 0 100 150 200 300 400 500 600 700 800 900 1000
125 130
PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT
10000 10000
MAY TRIP
MAY TRIP
100 100
TIME IN SECONDS
TIME IN SECONDS
10 10
1 1
.1 .1
.01 .01
.001 .001
0 100 150 200 300 400 500 600 700 800 900 1000 0 100 150 200 300 400 500 600 700 800 900 1000
135 135
PERCENT OF RATED CURRENT
PERCENT OF RATED CURRENT
10000 10000
100 100
IAL/IUL/IEL/LEL
TIME IN SECONDS
TIME IN SECONDS
10 10
MAY TRIP
1 1
.1 .1
.01 .01
.001 .001
0 100 150 200 300 400 500 600 700 800 900 1000 0 100 150 200 300 400 500 600 700 800 900 1000
135 135
PERCENT OF RATED CURRENT PERCENT OF RATED CURRENT
Ounces Grams
M3 mounting inserts 4 - 5 inch pounds 3.1 90
10 - 32 screw terminals 14 - 15 inch pounds
M5 screw terminals 14 - 15 inch pounds
10 - 32 stud terminals 13 - 14 inch pounds
M5 stud terminals 13 - 14 inch pounds
1
4 - 20 stud terminals 40 - 45 inch pounds
M6 studs 40 - 45 inch pounds
decision steps in the appropriate part number IAL IAL One handle
One handle per unit
per unit Standard
Standard screwscrew terminal,
terminal,
**IUL**IUL no designation
no designation required
required
decision table subsequent to this page. ***IEL***IEL
K K Stud terminals
Stud terminals
The coding given permits a self-assigning part One handle
IALH IALH One handle per pole
per pole
C C Clip terminals
Clip terminals
number but with certain limitations. Special **IULH
**IULH
***IELH
***IELH B B BulletBullet terminals
terminals
applications may require a factory assigned part
One handle
IALN IALN One handle per unit
per unit
number. Typical examples are units with mixed ***IULN panelpanel
***IULN seal seal
ratings, combinations of styles, or constructions not One handle
One handle per unit,
per unit,
IALX IALX 2 2Second
Second Decision
Decision
listed in the third decision table, etc. With these, it **IULX
**IULX rocker,rocker, bracket
bracket mounting
mounting
***IELX
***IELX PolesPoles
is suggested that order entry be by description and/
One handle
IALZXIALZX One handle per unit,
per unit,
or drawings, and a part number will be established. **IULZX rocker,rocker,
**IULZX integral
integral mounting
mounting
1 1 SingleSingle
pole pole
terminals
terminals (mid-trip
(mid-trip only) only)
measured in IEC 664. Intended for use in equipment to -1RS5-1RS5 SeriesSeries with alarm
with alarm switch,
switch,
-72 -72 DC/60Hz
DC/60Hz long delay
long delay
comply with IEC 950, 601 and VDE 0804 & 0805. electrical
electrical trip, quick
trip, .187 .187 quick connect
connect -73 -73 DC/60Hz
DC/60Hz
motormotor
start start
terminals
terminals
-79 -79 DC/60DC/60 Hz 135%
Hz 135% instant
instant trip trip
-3 -3 ShuntShunt For addition
For addition of inertial
of inertial delay,
delay, add an add
ìFî toanany
ìFî to any
-4 -4 RelayRelay (not available
(not available in IEL/IELX)
in IEL/IELX) delay numeral.
delay numeral.
The shaded
The shaded areas areas
denotedenote
VDE and VDECCCand CCC
(if applicable)
(if applicable) Approval
Approval options.options. This approval
This approval
requires
requires the addition
the addition of a V of
at athe
V at
endtheofend
the of the
C =Approved
C = CCC CCC Approved part number.
part number. The V The
will Vbewill be added
added to anytopart
any part
numbernumber
formedformed
entirelyentirely from shaded
from shaded decisions.
decisions.
If non-shaded
If non-shaded areas
areas are are selected,
selected, the unitthewill
unitnotwill not
This approval
This approval requires
requires the addition
the addition of a C of
at athe
C at
endthe end be VDEbeorVDECCCorApproved,
CCC Approved, but approvals
but other other approvals
of the of thenumber.
part part number. Thewill
The unit unitnotwill
benot
VDEbeApproved.
VDE Approved. still apply.
still apply.
Note:
Note: CCC CCC Approval
Approval is pending.
is pending. Note:
Note: CCC CCC Approval
Approval is pending.
is pending.
156 IAL/IUL/IEL Decision Tables
5 5 Decision
Fifth Fifth Decision 6 6 Sixth
Sixth Decision
Decision
INDICATING
ROCKER
RatedRated Current
Current Optional
Optional ON
I
HANDLE
COLOR
COLOR
ON
I
O
OFF
Standard
Standard ratings ratings listed.
listed. For Forratings,
other other ratings, Standard
Standard hardware.
hardware. No designation
No designation required.
required. O
OFF
ROCKER
HANDLE
please contact
please contact the factory.
the factory. INDICATING
COLOR
COLOR
-A -A MetricMetric
threadthread mounting
mounting inserts
inserts and terminals
and terminals
.100 .100 20.0 20.0
-B -B Barrier
Barrier LINE
.250 .250 30.0 30.0 INDICATION “ON”
LINE
INDICATION “OFF”
Mounting/Indicator Code: A, B, C Mounting/Indicator Code: F, G, H
.500 .500 35.0 35.0 -C -C 277V 277V (50/60Hz
(50/60Hz only) only) (See 3)
(See note note 3)
Usenumbers
Use three three numbers
to printtorequired
print required
value value -M -MHandle
Handle in opposite
in opposite pole pole OFF
O
betweenbetween .050 amperes
.050 amperes minimum minimum
and 100.0 and 100.0 ROCKER
HANDLE
I
amperesamperes
maximum.maximum.
The VDEThe VDE
(Ith) will(Ith)
be will
95%be 95% -P -P Snap-in
Snap-in face plate
face plate adapter
adapter ON COLOR
of the UL/CSA
of the UL/CSA rated current.
rated current.
-T -T 80VDC80VDC
INDICATION “ON”
-U -U 120/240V
120/240V 50/60Hz
50/60Hz Mounting/Indicator Code: J, K, L
7 7 Seventh
Seventh Decision
Decision
-W -WWire Wire
clampclamp supplied
supplied (VDE approved
(VDE approved up to up to LINE OFF
O OFF
O LOAD LINE LOAD LINE LOAD LINE
Handle
Handle ColorColor and Marking
and Marking Selection
Selection and including
and including 16.0 amps)
16.0 amps) LOAD ON ON
ON OFF
O ON OFF
O
-X -X HandleHandle
guardguard with
with no no actuation
actuation feature
feature
IAL,IEL,
IAL, IUL, IUL,IALH,
IEL, IALH, MARKING DETAIL “B” (SEE TABLE)
(BX rocker
(BX rocker only) only)
IULH,IULH,
IELH -IELH - Toggle
Toggle Handle
Handle
-1 -1 SilverSilver
5/16"5/16"
(.312")(.312")
bulletbullet
Marked*
Marked*
ON-OFF
ON-OFF -2 -2 Gold 5/16"
Gold 5/16"
(.312")(.312")
bulletbullet
Color Color Unmarked
Unmarked I-O I-O Notes: Notes:
1. One
1. One or moreordescriptions
more descriptions
may bemay
usedbeasused as required.
required.
2. When2.this
When thisused,
is not is nottable
used,one
table
mayone
bemay be substituted
substituted and U.S.and U.S. and
thread thread and
BlackBlack -00 -00 -01 (STD)
-01 (STD) two lockwashers
two lockwashers will be will be supplied.
supplied. Unit willUnit
be will
ratedbeatrated
250Vat(50/60Hz
250V (50/60Hz
only.) only.)
3. VDE 3. VDE approved
approved at 250Vac
at 250Vac
4. VDE 4. VDE approved
approved at 415Vac
at 415Vac
Yellow
Yellow -10 -10 -11 -11
LINE
7 7 Seventh
Seventh Decision
Decision
Rocker
Rocker Handle
Handle Color,Color, Indicator
Indicator ColorColor and Marking
and Marking Selection
Selection (See Notes)
(See Notes)
IALX,IALX,
IULX,IULX,
IELX, IELX,
IALZX,IALZX,
IULZX,IULZX,
IELZXIELZX Rocker
Rocker Handle
Handle (Single
(Single Rocker
Rocker Color)Color)
Vertical
Vertical Mounting
Mounting Horizontal
Horizontal Mounting
Mounting
RockerRocker On-OffOn-Off On-OffOn-Off
HandleHandle Indicating
Indicating Marking
Marking On-OffOn-Off I-O I-O I-O I-O On-OffOn-Off I-O I-O I-O I-O Marking
Marking
Color Color Color Color Color Color Indicates:
Indicates: Unmarked
Unmarked Fig.1 Fig.1 Fig.2 Fig.2 Fig.3 Fig.3 Fig.4 Fig.4 Fig.5 Fig.5 Fig.6 Fig.6 DetailDetail
Black Black N/A N/A WhiteWhite N/A N/A -00 -00 -01 -01 -02 -02 -03 -03 -04 -04 -05 -05 -06 -06
Red Red N/A N/A White White N/A N/A -20 -20 -21 -21 -22 -22 -23 -23 -24 -24 -25 -25 -26 -26
Grey Grey N/A N/A Black Black N/A N/A -40 -40 -41 -41 -42 -42 -43 -43 -44 -44 -45 -45 -46 -46 A A
OrangeOrange N/A N/A Black Black N/A N/A -50 -50 -51 -51 -52 -52 -53 -53 -54 -54 -55 -55 -56 -56
WhiteWhite N/A N/A Black Black N/A N/A -90 -90 -91 -91 -92 -92 -93 -93 -94 -94 -95 -95 -96 -96
IALZX,IALZX,
IULZX,IULZX,
IELZXIELZX
RockerRocker
HandleHandle
(Dual (Dual
RockerRocker
Color)Color)
Black Black WhiteWhite WhiteWhite On On -A0 -A0 -A1 -A1 -A2 -A2 -A3 -A3 -A4 -A4 -A5 -A5 -A6 -A6
Black Black Red Red White White On On -B0 -B0 -B1 -B1 -B2 -B2 -B3 -B3 -B4 -B4 -B5 -B5 -B6 -B6
IAL/IUL/IEL/LEL
Black Black GreenGreen WhiteWhite On On -C0 -C0 -C1 -C1 -C2 -C2 -C3 -C3 -C4 -C4 -C5 -C5 -C6 -C6 A A
Black Black WhiteWhite WhiteWhite Off Off -F0 -F0 -F1 -F1 -F2 -F2 -F3 -F3 -F4 -F4 -F5 -F5 -F6 -F6
Black Black Red Red WhiteWhite Off Off -G0 -G0 -G1 -G1 -G2 -G2 -G3 -G3 -G4 -G4 -G5 -G5 -G6 -G6
Black Black GreenGreen WhiteWhite Off Off -H0 -H0 -H1 -H1 -H2 -H2 -H3 -H3 -H4 -H4 -H5 -H5 -H6 -H6
Black Black WhiteWhite WhiteWhite On On -J0 -J0 -J1 -J1 -J2 -J2 -J3 -J3 -J4 -J4 -J5 -J5 -J6 -J6
Black Black Red Red White White On On -K0 -K0 -K1 -K1 -K2 -K2 -K3 -K3 -K4 -K4 -K5 -K5 -K6 -K6 B B
Black Black GreenGreen White White On On -L0 -L0 -L1 -L1 -L2 -L2 -L3 -L3 -L4 -L4 -L5 -L5 -L6 -L6
IALBX,IALBX,
IULBX,IULBX,
IELBX,IELBX,
LELBXLELBX
RockerRocker
HandleHandle
(Dual (Dual
RockerRocker
Color)Color)
Black Black WhiteWhite WhiteWhite Off Off -M0 -M0 N/A N/A -M2 -M2 -M3 -M3 N/A N/A N/A N/A -M6 -M6
Black Black Red Red Red Red Off Off -N0 -N0 N/A N/A -N2 -N2 -N3 -N3 N/A N/A N/A N/A -N6 -N6
Black Black GreenGreen GreenGreen Off Off -P0 -P0 N/A N/A -P2 -P2 -P3 -P3 N/A N/A N/A N/A -P6 -P6
C C
Black Black YellowYellow YellowYellow Off Off -R0 -R0 N/A N/A -R2 -R2 -R3 -R3 N/A N/A N/A N/A -R6 -R6
Notes: Notes: A. Bezels
A. Bezels of IALBX,
of IALBX, IULBX, IULBX, IELB,are
IELB, IELBX IELBX are black.
black. IAL/IUL/IEL
B. Consult
B. Consult factoryfactory formarking
for other other marking
options.options.
Decision Tables 157
LEL DECISION TABLES
Notes: The LEL family of circuit breakers are designed to meet 8mm creepage and clearance requirements for installation Category 111, pollution degree 3, Case A as mea-
sured in IEC 664. Intended for use in equipment designed to comply with IEC 380, 435, 601 AND VDE 0730, 0804 & 0805.
Black N/A White N/A -00 -01 -02 -03 -04 -05 -06
Red N/A White N/A -20 -21 -22 -23 -24 -25 -26
Grey N/A Black N/A -40 -41 -42 -43 -44 -45 -46 A
Orange N/A Black N/A -50 -51 -52 -53 -54 -55 -56
White N/A Black N/A -90 -91 -92 -93 -94 -95 -96 INDICATING
ROCKER COLOR
ON HANDLE
LELZX & LMLZX Rocker Handle (Dual Rocker Color) I
O
COLOR ON
I
OFF
O ROCKER
HANDLE
Black White White On -A0 -A1 -A2 -A3 -A4 INDICATING
-A5 -A6 OFF
COLOR
COLOR
Black Red White On -B0 -B1 -B2 -B3 -B4 -B5 -B6
A
LINE
Black Green White On -C0 -C1 -C2 -C3 -C4 -C5LINE -C6
INDICATION “ON” INDICATION “OFF”
Mounting/Indicator Code: A, B, C Mounting/Indicator Code: F, G, H
Black White White Off -F0 -F1 -F2 -F3 -F4 -F5 -F6
Black Red White Off -G0 -G1 -G2 -G3 LOAD ON
-G4 ON
LINE LOAD
-G5
LINE LOAD LINE LOAD
-G6
O O OFF ON
LINE O OFF ON O
OFF OFF
Black Green White Off -H0 -H1 -H2 -H3 FIG. 1 -H4FIG. 2 FIG. 3 FIG. 4 -H5FIG. 5 FIG. 6 -H6
MARKING DETAIL “A” (SEE TABLE)
Black White White On -J0 -J1 -J2 -J3 -J4 -J5 -J6
Black Red White On -K0 -K1 -K2 -K3 -K4 -K5 -K6 B
Black Green White On -L0 -L1 -L2 -L3 -L4LINE -L5 -L6
LELBX Rocker Handle (Dual Rocker Color) INDICATING
COLOR
Black White White Off -M0 N/A -M2 -M3 N/A N/AOFF
O
ROCKER
-M6
I
HANDLE
COLOR
Black Red Red Off -N0 N/A -N2 -N3 N/A N/A
ON
-N6
Black Green Green Off -P0 N/A -P2 -P3 N/A N/A -P6
C
INDICATION “ON”
Black Yellow Yellow Off -R0 N/A -R2 -R3 N/A Mounting/Indicator Code: J, K, L N/A -R6
Notes: A. Bezels of IALBX, IULBX, IELB, IELBX are black. LINE OFF
O OFF
O LOAD LINE LOAD LINE LOAD LINE
B. Consult factory for other marking options. O ON OFF
LOAD ON OFF
ON
O
ON
LINE
INDICATING COLOR
ROCKER HANDLE
ON COLOR INDICATING COLOR
I ON
I
O
OFF
O ROCKER HANDLE OFF
OFF COLOR O
ROCKER HANDLE
INDICATING I
COLOR
COLOR ON
NO
LINE ACTUATION
LINE LINE HANDLE HANDLE
ACCESS
POSITION “OFF” OPTIONAL POSITION “ON”
INDICATION “ON” INDICATION “OFF” INDICATION “ON” INDICATION “OFF” WITH GUARD WITH GUARD
Mounting/Indicator Code: A, B, C Mounting/Indicator Code: F, G, H Mounting/Indicator Code: J, K, L Mounting/Indicator Code: M, N, P, R
INDICATION “OFF”
Mounting/Indicator Code: M, N, P, R
MARKING DETAIL “A” (SEE TABLE) MARKING DETAIL “B” (SEE TABLE) MARKING
MARKING DETAILDETAIL “C” (SEE
“C” (SEE TABLE)
TABLE)
IAL/IUL/IEL/LEL