Professional Documents
Culture Documents
Datasheet
250W Switch Mode Power Supply with Standby and Universal
Universal mains
Page 2 of 20
DATASHEET
ICEpower200SC
Version 1.3
Contents
Version History ..........................................................................................................................................................2
General Description ................................................................................................................................................ 3
Block Diagram .......................................................................................................................................................... 4
Absolute Maximum Ratings ................................................................................................................................ 4
Thermal and efficiency specifications ............................................................................................................ 5
Dissipated power vs. Output power ................................................................................................................. 5
Electrical Specifications ........................................................................................................................................7
Timing Specification ................................................................................................................................................7
DC protection specifications ............................................................................................................................... 8
Connection Diagram ............................................................................................................................................... 8
Connector pin description .................................................................................................................................. 10
Interfacing ............................................................................................................................................................... 11
Protection Features .............................................................................................................................................. 14
Thermal Design ...................................................................................................................................................... 14
Physical Dimensions ............................................................................................................................................ 15
Drill Pattern ............................................................................................................................................................. 16
Safety Standards ................................................................................................................................................... 17
Touch Current ......................................................................................................................................................... 17
Disturbances on the Mains ................................................................................................................................ 17
EMC ............................................................................................................................................................................. 17
Electrostatic Discharge ...................................................................................................................................... 18
Environmental and Reliability Tests ............................................................................................................. 18
Mechanical Tests................................................................................................................................................... 18
ESD Warning............................................................................................................................................................ 19
Packaging and Storing ......................................................................................................................................... 19
Notes ........................................................................................................................................................................... 20
Version History
Issue Date Remark
1.0 23/11-09 First issue
1.1 21/04-10 Minor updates e.g. DC-sense changed to DC-protection
1.2 12/05-10 Module width and height added to Physical dimensions drawing
1.3 18/07-12 Rev. C. Updated with new standby requirements.
Page 3 of 20
DATASHEET
ICEpower200SC
Version 1.3
General Description
The ICEpower200SC is a fully integrated, SMPS module designed particularly for highly competitive consumer
and professional audio applications. The ICEpower200SC is pre-approved for EMC and safety and the “black-box”
completeness allows for fast design-in and minimized time to market.
Key benefits include:
The ICEpower200SC is an integrated power solution which completely eliminates the need for heat sinks and
EMI shields. The ICEpower200SC also provides an auxiliary +/-12V supply for external signal conditioning
circuitry and the DC-bus output for powering ICEpower200AC amplifiers makes designing compact multi-way or
multi-channel solutions easy.
Block Diagram
DC-
DC- bus
Symbol Parameter Value Units
2)
I+12V Maximum current draw from Vcc (+12V) 370 mA
2)
I-12V Maximum current draw from Vss (-12V) 220 mA
2)
IAUX Maximum current draw from Vcc and Vss 490 mA
(sum of I+12V and I-12V)
IVsleep Maximum current draw from Vsleep 6 mA
Table 2: Absolute maximum ratings DC-bus.
2) The +/-12V outputs are not over current protected. Exceeding these limits may permanently damage the device.
Control section
Symbol Parameter Value Units
Mode Maximum voltage range on pin -1 to Vsleep V
Signal Sense Maximum voltage range on pin ±12 V
Standby Maximum voltage range on pin -5 to +50 V
Table 3: Absolute maximum ratings control section.
Page 5 of 20
DATASHEET
ICEpower200SC
Version 1.3
Thermal section
Symbol Parameter Value Units
O
Ta Max. operating ambient temperature 45 C
Table 4: Thermal section
Electrical Specifications
O
Unless otherwise specified, Ta=25 C.
Symbol Parameter Conditions Min Typ Max Units
Vp Nominal DC voltage Off-line input within range 46 47 48 V
Vcc Positive analog supply Off-line input within range 11.4 12 12.4 V
Vss Negative analog supply Off-line input within range -11.4 -12 -12.4 V
VSleep-on Standby supply in on mode Unloaded - 11 - V
VSleep-standby Standby supply in standby Unloaded - 8.5 - V
mode
VSleep-Z Ouput impedance - 300 - Ω
fsmps Switching frequency - 65 - kHz
Vtrig Signal Sense trigger level - 1 3 mVRMS
VStandby.L Standby low level -5 0.1 1.0 V
VStandby.H Standby high level 3 5 -12 50 V
Vmode.L Mode low level -1 0.1 1.0 V
Vmode.H Mode high level 4.5 5 to Vsleep V
Vsleep
Table 7: Electrical specifications
Timing Specification
Symbol Parameter Conditions Min Typ Max Units
tacd-1 Power supply Time from reaching ACmin to all power - 2.5 - s
start up supplies are good. No signal at
delay. Signal_Sense pin. Mode pin = low.
tacd-2 Power supply Time from reaching ACmin to all power - 700 - ms
start up supplies are good. Signal at Signal_Sense
delay. pin. Mode pin = low.
tsystemd 200SC and Time from reaching ACmin to signal - 1.3 - s
200AC start amplification. Signal at Signal_Sense pin.
up delay. Mode pin = low.
tstandby Shutdown Time to shutdown from signal on - 13 - min
delay Signal_Sense pin disappears
tstbon1 Standby to on Time from standby to all power supplies - 200 400 ms
delay are good.
Mode pin = low.
Activation via Standby pin.
tstbon2 Standby to on Time from standby to all power supplies - 2 3 s
delay are good.
Standby pin = low.
Activation via Mode pin.
tstbon3 Standby to on Time from standby to all power supplies - 500 - ms
delay are good.
Standby pin = low, Mode pin = NC.
Activation via 100mVp 1kHz sine at
Signal_Sense pin.
Table 8: Timing specifications
Page 8 of 20
DATASHEET
ICEpower200SC
Version 1.3
DC protection specifications
Symbol Parameter Conditions Min Typ Max Units
Vdcprot Shutdown Slowly changing dc-voltage (1V/s) - 4.9 - V
voltage
Tdcprot-1 Shutdown Time to shutdown from signal on DC prot. - 1 - s
delay appears (DC_prot.+ = 23.5V, DC_prot- = 13.5V)
Tdcprot-2 Shutdown Time to shutdown from signal on DC Sense - 430 - ms
delay appears (DC_prot. + = 23.5V, DC_prot. - = 0V)
Table 9: Timing specifications
Connection Diagram
DC-
DC - bus header specification (J1)
Type: JST B 2P-NH
PIN Function Description Type
1 Vp (47V) Power supply +47V Output
2 GND Ground terminal for the power section Output
Table 11: DC-bus header specification
Interfacing
The ICEpower200SC has a number of useful features as described below.
+12Vst_by
1k8
Red
GND
+12V
Green
1k8
Signal Sense
The board is able to power up from standby mode by applying an audio signal to the Signal_Sense input pin.
When an audio signal is detected the power supply will switch from standby mode to on mode and the amplifier
will turn on. The power supply will return to standby mode again if no audio signal has been detected for 13
minutes (typical).
If this feature is not required the input it can be left unconnected or connected to ground.
The internal circuit for the Signal_Sense input pin is shown in Figure 4.
-
C1
Signal_Sense 10k
+
GND 470k C1
Vsleep
This low power DC output can be used for supplying external wake-up circuits such as microprocessors. The
output can supply up to 6mA. The output impedance is quite high as shown in Figure 5. This means that the
output voltage drops as a function of the loading on this pin.
GND
Mode
The Mode input pin can be used in several ways to control the on/off behavior of the ICEpower200SC.
• On/Off by Signal sense: If the ICEpower200SC should power up when an input signal is detected, the
Mode pin should be unconnected and the Signal Sense pin connected to the input signal. The board will
then turn on when an input signal is detected and automatically shut down approximately 13 minutes
after the input signal has been removed.
• On/Off by mains switch: If the board should power up when mains voltage is present, the Mode pin
should be connected to GND as shown in figure 6 to disable the Signal Sense feature.
• On/Off by control signal: The Mode input pin can also be used to control the standby/on mode via an
external control signal. The recommended external circuit for this is illustrated in Figure 7. The board will
turn on when the external transistor turns on.
DC protection
The DC protection circuit is intended to switch off the power supply in case of DC across a driver. An error in the
amplifier circuit could cause a DC output from the amplifier. DC across a driver could damage the driver. To
prevent this, connect the DC protection pins across the driver, and the power supply will shut down in case of
error. The input is differential and high impedance.
Protection Features
The ICEpower200SC is equipped with varoius protection features for surviving overload under extreme conditions
without damage. The figure below illustrates the different protection features. The explanation below refers to
this block diagram.
Thermal Design
Thermal design is generally a great challenge in power amplifier systems. Linear amplifier designs operating in
class A or AB are normally very inefficient and therefore equipped with extensive heatsinking to keep the
transistor junction temperature low. The ICEpower200SC is based on highly efficient ICEpower switching
technology providing high overall efficiency characteristics at all levels of operation.
Part of the “component” philosophy of the SC–series is to provide a self-cooled component thus eliminating the
need for special attention to thermal design.
The ICEpower200SC module is designed for music reproduction, which means that the output power of the
applied amplifier will never be continuous. If the average power of the output signal exceeds 100W for a long time
at 25°C ambient temperature, the module will reach its maximum allowable temperature and the temperature
protection will be activated.
Physical Dimensions
All dimensions are in mm.
95.0
107.0
Important! Ensure sufficient clearance for live parts and adequate ventilation.
Drill Pattern
All dimensions are in mm. The diameter of the mounting holes is 3.5 mm.
Safety Standards
The ICEpower200SC is safety pre-approved to ease the design-in procedure. The module complies with the
following standards:
th
Europe: IEC 60065 7 ed. + A1
US: UL 60065: 2007
Safety Class: Class 2
Touch Current
Touch Current is measured according to IEC 60999 with the following results:
Point of Measurement Measurement Result Specified Limit, IEC60065
U1 171mVpeak 35Vpeak
U2 140mVpeak 350mVpeak
Figure 13: Touch current
Consequently there is room left for additional Y1 capacitor decoupling of the mains for other circuits.
The stated U2 results are worst case measurements according to IEC60999. Worst case is seen at neutral mains
wire interrupted. In operating mode, U2 is approximately half the stated value.
This operating mode value can be made the worst case if mains is routed through a two-pole relay, given the relay
opens in case of neutral mains wire failure.
Special care and component selection has made the ICEpower200SC able to withstand surges up to 8kV, to avoid
damage to the ICEpower200SC in case of surges caused by lightning.
EMC
When mounted on a back plate as shown in the Designers Manual the ICEpower200SC fulfils the following
requirements with good margin.
Electrostatic Discharge
ICEpower has conducted and passed the following tests:
Type Test Level Environment
Internal Contact, small signal 5kV Production, handling,
connectors service
External Contact, loudspeaker and 8kV End User
mains
Table 15: Electrostatic discharge
Mechanical Tests
The ICEpower200SC has passed the following mechanical tests to ensure high reliability. Resonance search
carried out during sinusoidal vibration test.
Test Acceleration Amount Performance
Verification
Random 2gRMS 3x20min After test
vibration
Bump 10g/16ms, 2-4 Hz 1000 bumps in each of 6 After test
4)
directions
Shock 70g/12ms 3 shocks in each of 6 After test
4)
directions
Sinusoidal 2.5mm, 5-10Hz 2 hours in each of 3 Continuous
4)
vibrations 1g, 10-100Hz directions monitoring
Random 0.01g, 10-20Hz 2 hours in each of 3 Continuous
4)
vibrations 0.7gRMS –3dB/oct, directions monitoring
20-150Hz
Table 17: Mechanical tests
4)
6 directions: (up, down, left, right forward and backward). 3 directions: (up and down, left and right, forward and backward)
Page 19 of 20
DATASHEET
ICEpower200SC
Version 1.3
ESD Warning
ICEpower products are manufactured according to the following ESD precautions:
IEC 61340-5-1: Protection of electronic devices from electrostatic phenomena. General Requirements.
IEC 61340-5-2: Protection of electronic devices from electrostatic phenomena. User Guide.
ANSI/ESD-S20.20-1999: Protection of Electrical and Electronic Parts, Assemblies and Equipment.
Further handling of the products should comply with the same standards.
The general warranty policy of ICEpower a/s does not cover ESD damaged products due to improper handling.
Storage humidity
Do not expose the pallets to humidity levels higher than 85% or rain.
Storage temperature
The pallets are to be stored at temperatures from 0°C to 70°C.
Stacking
Pallets may not be stacked on top of each other.
Page 20 of 20
DATASHEET
ICEpower200SC
Version 1.3
Notes
For additional information about the ICEpower® technology from ICEpower a/s, visit our web site or contact us.
ICEpower a/s
Gl. Lundtoftevej 1b
DK-2800 Kgs. Lyngby
Denmark
Website http://www.ICEpower.bang-olufsen.com
E-Mail info@icepower.dk
Notice
The data sheet contains specifications that may be subject to change without prior notice. ICEpower® is a
trademark ofICEpower a/s.
ICEpower a/s products are not authorized for use as critical components in life support devices
or systems without the express written approval of the president and general counsel ofICEpower a/s. As used
herein:
1. Life support devices or systems are devices or systems which
a. are intended for surgical implant into the body, or
b. support or sustain life, and whose failure to perform when properly used in accordance with
instructions for use provided in the labeling, can be reasonably expected to result in a significant
injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system, or to affect its safety or
effectiveness.