Professional Documents
Culture Documents
G 4305 : 2012
table of contents
page
preface 1
1 Scope of application 1
2 Normative standard 1
3 Types of symbols 2
Production method
Four 2
Chemical composition
Five 3
6 mechanical nature 7
7 Corrosion resistance 11
8 Surface finish 11
Ten appearance 18
11 test 19
12 Inspection 20
13 display 20
14 report 20
Annex JB (reference) Comparison table between JIS and compliant international standards twenty three
(1)
G 4305 : 2012
Foreword
This standard is based on the provisions of Article 12, paragraph 1 applied mutatis mutandis pursuant to Article 14 of the Industrial Standardizat
(JSSA) and Japan Standards Association (JSA) should revise the Japanese Industrial Standard with the original industrial standards
It is a Japanese Industrial Standard which was revised by the Minister of Economy, Trade and Industry after deliberation by the Japanese Industria
As a result, JIS G 4305 : 2010 was revised and replaced by this standard.
In addition, until September 19, 2013, JISMA based on the provisions of the relevant clauses such as Article 19, Paragraph 1 of the Industrial St
It can be done according to JIS G 4305 : 2010 in certification display certification .
This standard is a copyrighted work subject to copyright law.
Keep in mind that following this standard may correspond to the use of patents etc. of the following persons.
Types of symbols Title of invention Patent numberDate of registration registration
No. 2602411
SUS 315 J 1 Austenitic excellent corrosion resistance in hot workability and warm water January 29, 1997
SUS 315 J 2 collected by stainless steel
SUS443J1 No. 4396676 October 30, 2009
Ferritic stainless steel sheet excellent in corrosion resistance and
manufacturing method thereof
SUS445J1 Ferritic stainless steel for heat exchanger No. 2642056 May 2, 1997
SUS445J2 Fe - Cr alloy excellent in ridging resistance No. 2737819 January 16, 1998
Ferritic stainless steel excellent in rust resistance and workability
No. 3224694 August 24, 2001
Ferrite type stainless steel brilliant with excellent processability and
No. 3268927
rust resistance
January 18, 2002
Annealed material
Ferrite stainless steel for exterior materials excellent in corrosionNo.
resistance
3297696 April 19, 2002
Ferritic stainless steel for building materials No. 3411084 March 20, 2003
The above-mentioned right holder of a patent right, etc. Shall implement the patent right etc. to any person under non-discriminatory and reason
It is expressing that there is intention to give permission etc. However, for rights holders of other patents etc. related to this standard
In addition, it is conditional on that the implementation is permitted under similar conditions.
It should be noted that conforming to this standard does not necessarily mean that the patent right is free of charge
.
A part of this standard may conflict with patent rights etc. other than those indicated above. Minister of Economy, Trade and Industry and Japan
The quasi-investigative committee is not responsible for confirmation concerning such patent rights etc.
Here, the term "patent right etc." means a patent right, a patent application after the application is opened, or a utility model right.
(2)
preface
This standard was issued as the first edition in 2004, ISO 16143-1 , issued in 2009 as the first version of ISO
9445-1 Based on ISO 9445-2 , it is a Japanese Industrial Standard created by changing technical contents.
The part given the side line in this standard is a matter that changes the corresponding international standard. In the change list
With that explanation,It is shown in Annex JB .
1 Scope of application
This standard is a cold-rolled stainless steel plate (hereinafter) referred
And cold-rolled
to as a plate;
stainless steel strip
. ).
NOTE The corresponding international standards and symbols indicating the degree of correspondence are as follows.
ISO 16143-1 : 2004 , Stainless steels for general purpose-Part 1: Flat products
ISO 9445-1 : 2009, Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part
1: Narrow strip and cut lengths
ISO 9445-2 : 2009, Continuously cold-rolled stainless steel - Tolerances on dimensions and form - Part
2: Wide strip and plate / sheet
(Overall Evaluation: MOD)
The symbol "MOD" representing the degree of correspondence is based on ISO"I/ IEC
am correcting"
Guide 21-1 ,
.
2 Normative standard
The following standards constitute a part of the provisions of this standard by quoting this standard. these
For undated references, the latest edition of
) Isthe
applied.
referenced document (including any amendments) applies.
JIS G 0320 Molten steel analysis method for steel materials
JIS G 0321 Product analysis method of steel material and its allowable variation value
JIS G 0404 General delivery conditions of steel materials
JIS G 0415 Steel and steel products - inspection documents
Note International standard: ISO 10474 : 1991, Steel and steel products-Inspection documents (IDT)
JIS G 0571 Oxalic acid etching test method of stainless steel
JIS G 0572 Stainless steel sulfuric acid · ferric sulfate corrosion test method
JIS G 0573 65% nitric acid corrosion test method of stainless steel
JIS G 0575 Stainless steel sulfuric acid · copper sulfate corrosion test method
JIS R 6010 Particle size of abrasive material for abrasive cloth paper
2
G 4305 : 2012
3 Types of symbols
There are 62 types of boards and bands, the types of symbols and classifications
See Table 1 are. as follows:
a) , b)
Table 1a)-, Types
b)
of symbols and classification a) , b)
Types of symbols Classification Types of symbols Classification Types of symbols Classification
SUS301 Austenitic SUS 316 LN Austenite type SUS 430 Ferrite type
SUS 301L SUS 316 Ti SUS 430 LX
SUS301J1 SUS 316 J 1 SUS430J1L
SUS302B SUS 316 J 1 L SUS434
SUS 304 SUS 317 SUS 436 L
SUS304Cu SUS 317 L SUS436J1L
SUS 304 L SUS 317 LN SUS443J1
SUS304N1 SUS317J1 SUS444
SUS 304 N 2 SUS317J2 SUS445J1
SUS 304 LN SUS836L SUS445J2
SUS304J1 SUS890L SUS447J1
SUS304J2 SUS 321 SUSXM 27
SUS 305 SUS 347 SUS 403 Martensitic system
SUS 309 S SUSXM 7 SUS 410
SUS 310 S SUSXM 15 J 1 SUS 410 S
SUS312L SUS329J1 Austenite · SUS420J1
SUS 315 J 1 SUS 329 J 3 L Ferrite type SUS 420 J 2
SUS 315 J 2 SUS 329 J 4 L SUS 440 A
SUS 316 SUS 405 Ferrite type SUS 630 Precipitation hardening system
SUS 316 L SUS 410 L SUS 631
SUS 316 N SUS 429
a)
note If it is necessary to express that it is a board with a symbol, add -CP at the end of the type symbol.
Example SUS304-CP
b)
If it is necessary to express that it is a band with a symbol, add -CS at the end of the type symbol.
Example SUS 304 - CS
FourProduction method
The manufacturing method is as follows.
a) After cold rolling, heat treatment is performed on plates and bands, pickling or similar processes are performed. Appropriate correction as nec
Positive, abrasive, temper rolling, or a combination thereof may be carried out. However, brilliant heat treatment was performed
, The treatment such as pickling may be omitted.
NOTE Typical heat treatment conditions are shown in Annex JA for reference. Heat treatment conditions other than these conditions are u
Sometimes it is.
3
G 4305 : 2012
b) SUS 420 J 2 For SUS 440A, Particularly when there is designation Quenching
of an orderer,
and tempering may be performed.
In this case, the symbol of Q is added.
c) SUS 630 And the heat treatment of SUS 631, the orderer specifies either solution heat treatment or precipitation hardening treatment
. in this case, Symbols for types of heat treatment according to Table 2 are added.
Four
G 4305 : 2012
Five
G 4305 : 2012
6
G 4305 : 2012
6 mechanical nature
6.1 General information
The plate and band subjected to heat treatment shall be subjected to the test of 11.2 and its mechanical properties shall be in accordance with
mm , The tensile test may be omitted.
6.2 Mechanical properties of austenite type
The mechanical properties of the austenitic system are according to a) or b) below .
a) See Table
The mechanical properties of plates and bands subjected to solid8 solution
. In this heat
case,treatment
test material
wereis,asJIS G 0404 of 7.6
follows:
(Specimen collection condition and specimen) according to type A However, the proof stress is applied when there is a designation by the ord
b) Strength, tensile strength and elongation of plates and bands of SUS 301 and SUS 301 L, which were subjected to temper rolling for curing,
See Table 9 . In this case, the test material is according to class A of 7.6 of JIS G 0404 . However, the proof stress, in particular,
Apply when there is designation.
9
G 4305 : 2012
Ten
G 4305 : 2012
11
G 4305 : 2012
7 Corrosion resistance
Regarding corrosion resistance by intergranular corrosion test, if there is designation by the orderer, trial to apply from 11.3 between the deliver
Agreement on the method of testing, tests, corrosion resistance according to the agreement between the delivering parties.
8 Surface finish
The surface finish of the plateSee
andTable
band,15 .
12
G 4305 : 2012
13
G 4305 : 2012
14
G 4305 : 2012
16
G 4305 : 2012
Table 23 - Tolerance of plate and strip thickness (symbol ST )
Unit mm
width
thickness 630 or more 1 000 that's all 1 250 that's all
1 000 Less than 1 250 Less than 1 550 Less than
0.25 Less than ± 0.030 - -
0.25Not less than 0.40 ± 0.030 ± 0.035 -
0.40Not less than 0.60 ± 0.035 ± 0.035 -
0.60Less than 0.80 ± 0.040 ± 0.040 -
0.80Not less than 1.00 ± 0.040 ± 0.050 ± 0.050
1.00Not less than 1.25 ± 0.050 ± 0.055 ± 0.060
1.25Not less than 1.60 ± 0.055 ± 0.060 ± 0.060
1.60Not less than 2.00 ± 0.065 ± 0.070 ± 0.080
17
G 4305 : 2012
18
G 4305 : 2012
Table 29 - Maximum flatness of the plates of SUS 301 and SUS 301 L
Unit mm
width thickness Maximum value of flatness
1/4 H 1/2 H
600 Not less than 1 000 0.40 Less than 13 19
0.40 Not less than 0.80 16 22
0.80 Not less than 19 twenty two
1 000 Not less than 1 219 0.40 Less than 16
0.40 Less than 0.80 19 29
0.80 Not less than 26 29
This table applies for arbitrary lengths of 3 500 mm and for lengths less than 3 500 mm,
apply for full length.
Ten appearance
Appearance is as follows.
a) Plates and strips shall not have harmful drawbacks in use. However, in the case of bands, in general, eliminating defects
Because there is no opportunity to do, it can include some non-normal parts.
b) The shape of the band is generally tightly wound and its appearance should be as cylindrical as possible.
c) Winding deviation of the band is within 70 mm for one end face, for a mill edge, 35 mm for a cut edge
. However, it is not applied to the non-normal parts of the front and end of the band.
19
G 4305 : 2012
11 test
11.1 Analysis test
11.1.1 General matters of analytical test and how to take analytical sample
General items of analytical tests and how to take analytical samples are according to Clause 8 (chemical composition) of JIS G 0404 . When th
How to sample when requesting analysis is according to Clause 4 (sampling method for analysis) of JIS G 0321 .
11.1.2 分析方法
溶鋼分析の方法は,JIS G 0320 による。製品分析の方法は,JIS G 0321 による。
11.2 機械試験
11.2.1 試験一般
機械試験の一般事項は,JIS G 0404 による。
11.2.2 供試材の採り方
供試材は,同一溶鋼及び同一熱処理条件の板又は帯ごとに 1 個を採取する。
11.2.3 試験片の数
引張試験,硬さ試験及び曲げ試験の各試験片の数は,供試材 1 個から各試験片 1 個とする。
11.2.4 試験片
引張試験片,硬さ試験片及び曲げ試験片は,次による。
a) 引張試験片は,JIS Z 2241 の 4 号試験片,10 号試験片又は 13B 号試験片のいずれかを用いる。
なお,14A 号試験片,14B 号試験片又は 5 号試験片を用いてもよい。
b) 硬さ試験片は,引張試験片又は曲げ試験片の一部を用いることができる。
c) 曲げ試験片は,JIS Z 2248 の 1 号試験片又は 3 号試験片を用いる。
11.2.5 試験方法
引張試験,硬さ試験及び曲げ試験の方法は,次による。
1)
なお,曲げ試験は省略してもよい 。ただし,特に注文者の指定がある場合には,試験を行わなければ
ならない。
1)
注 試験は,製造業者の判断によって省略してもよいが,曲げ性は規定を満足しなければならない
ことを意味する。
a) 引張試験方法は,JIS Z 2241 による。ただし,試験温度は 23±5 ℃とし,マルテンサイト系以外の引
張強さの測定については,試験片平行部のひずみ増加率が 40∼80 %/min になるような引張速度を用い
る。
b) 硬さ試験方法は,次のいずれかによる。ただし,試験温度は,23±5 ℃で行う。
1) JIS Z 2243
2) JIS Z 2244
3) JIS Z 2245
c) 曲げ試験方法は,JIS Z 2248 による。ただし,試験温度は,23±5 ℃で行う。
11.3 腐食試験
11.3.1 供試材の採り方
供試材は,同一溶鋼及び同一熱処理条件の板又は帯ごとに 1 個を採取する。
11.3.2 試験片の数
試験片の数は,供試材 1 個から各試験片 1 個とする。
20
G 4305 :2012
11.3.3 試験方法
試験方法は,次のいずれかによる。
a) JIS G 0571
b) JIS G 0572
c) JIS G 0573
d) JIS G 0575
12 検査
板及び帯の検査は,次による。
a) 検査の一般事項は,JIS G 0404 による。
b) 化学成分は,箇条 5 に適合しなければならない。
c) 機械的性質は,箇条 6 に適合しなければならない。ただし,引張試験,硬さ試験及び曲げ試験は,受
渡当事者間の協定によって,その一部又は全部を省略することができる。
d) 耐食性は,注文者の指定がある場合に適用し,箇条 7 に適合しなければならない。
e) 表面仕上げは,箇条 8 に適合しなければならない。
f) 形状及び寸法は,箇条 9 に適合しなければならない。
g) 外観は,箇条 10 に適合しなければならない。
13 表示
検査に合格した板及び帯には,板については 1 枚ごと又は 1 結束ごとのいずれかに,帯については 1 結
束ごとに次の事項を表示する。ただし,受渡当事者間の協定によって,項目の一部を省略することができ
る。
a) 種類の記号
b) 寸法
c) 許容差及び板の平たん度の最大値の記号(許容差の記号 ET,ST 又は EW,及び板の平たん度の最大
値の記号 EF によったものについては,これを表示する。 )
d) 表面仕上げの記号
e) 熱処理記号(析出硬化系の場合,並びにマルテンサイト系のうちで特に注文者から指定された SUS
420J2 及び SUS440A の焼入焼戻しの場合に限る。 )
f) 調質の記号(SUS301 及び SUS301L の場合)
g) 製造業者名又はその略号
h) 溶鋼番号又は検査番号
14 報告
製造業者は,注文者の要求があれば,この規格に規定又は指定された試験の成績表,及び寸法,数量,
納入状態などを記載した報告書を注文者に提出しなければならない。
報告書には電送などの電子媒体も含める。ただし,検査文書の種類は,JIS G 0415 の 表 1(検査文書の
総括表)の 2.3(受渡試験報告書)又は 3.1.B(検査証明書 3.1.B)とする。
21
G 4305 :2012
附属書 JA
(参考)
ステンレス鋼の熱処理
序文
この附属書は,本体に関連する事柄を補足するもので,規定の一部ではない。
板及び帯の熱処理条件を参考として以下に示す。
JA.1 熱処理条件
表 JA.1∼表 JA.5 に熱処理条件を示す。
表 JA.1−オーステナイト系の熱処理条件
単位 ℃
種類の記号 固溶化熱処理 種類の記号 固溶化熱処理
SUS301 1 010∼1 150 急冷 SUS316 1 010∼1 150 急冷
SUS301L 1 010∼1 150 急冷 SUS316L 1 010∼1 150 急冷
SUS301J1 1 010∼1 150 急冷 SUS316N 1 010∼1 150 急冷
SUS302B 1 010∼1 150 急冷 SUS316LN 1 010∼1 150 急冷
a)
SUS304 1 010∼1 150 急冷 SUS316Ti 920∼1 150 急冷
SUS304Cu 1 010∼1 150 急冷 SUS316J1 1 010∼1 150 急冷
SUS304L 1 010∼1 150 急冷 SUS316J1L 1 010∼1 150 急冷
SUS304N1 1 010∼1 150 急冷 SUS317 1 010∼1 150 急冷
SUS304N2 1 010∼1 150 急冷 SUS317L 1 010∼1 150 急冷
SUS304LN 1 010∼1 150 急冷 SUS317LN 1 010∼1 150 急冷
SUS304J1 1 010∼1 150 急冷 SUS317J1 1 030∼1 180 急冷
SUS304J2 1 010∼1 150 急冷 SUS317J2 1 030∼1 180 急冷
SUS305 1 030∼1 150 急冷 SUS836L 1 030∼1 180 急冷
SUS309S 1 030∼1 180 急冷 SUS890L 1 030∼1 180 急冷
a)
SUS310S 1 030∼1 180 急冷 SUS321 920∼1 150 急冷
a)
SUS312L 1 010∼1 150 急冷 SUS347 980∼1 150 急冷
SUS315J1 1 010∼1 150 急冷 SUSXM7 1 010∼1 150 急冷
SUS315J2 1 010∼1 150 急冷 SUSXM15J1 1 010∼1 150 急冷
a)
注 SUS316Ti ,SUS321 及び SUS347 については,注文者が安定化熱処理を指定す
ることがある。この場合の熱処理温度は,850∼930 ℃が用いられる。
表 JA.2−オーステナイト・フェライト系の熱処理条件
単位 ℃
種類の記号 固溶化熱処理
SUS329J1 950∼1 100 急冷
SUS329J3L 950∼1 100 急冷
SUS329J4L 950∼1 100 急冷
22
G 4305 :2012
表 JA.3−フェライト系の熱処理条件
単位 ℃
種類の記号 焼なまし 種類の記号 焼なまし
SUS405 780∼830 急冷又は徐冷 SUS436J1L 800∼1 050 急冷
SUS410L 700∼820 急冷又は徐冷 SUS443J1 800∼1 050 急冷
SUS429 780∼850 急冷又は徐冷 SUS444 800∼1 050 急冷
SUS430 780∼850 急冷又は徐冷 SUS445J1 850∼1 050 急冷
SUS430LX 780∼950 急冷又は徐冷 SUS445J2 850∼1 050 急冷
SUS430J1L 800∼1 050 急冷 SUS447J1 900∼1 050 急冷
SUS434 780∼850 急冷又は徐冷 SUSXM27 900∼1 050 急冷
SUS436L 800∼1 050 急冷
表 JA.4−マルテンサイト系の熱処理条件
単位 ℃
種類の記号 熱処理
焼なまし 焼入れ 焼戻し
SUS403 約 750 急冷又は 800∼900 徐冷 − −
SUS410 約 750 急冷又は 800∼900 徐冷 − −
SUS410S 約 750 急冷又は 800∼900 徐冷 − −
SUS420J1 約 750 急冷又は 800∼900 徐冷 − −
SUS420J2 約 750 急冷又は 800∼900 徐冷 980∼1 040 急冷 150∼400 空冷
SUS440A 約 750 急冷又は 800∼900 徐冷 1 010∼1 070 急冷 150∼400 空冷
表 JA.5−析出硬化系の熱処理条件
種類の記号 熱処理
種類 記号 条件
a)
SUS630 固溶化熱処理 S 1 020∼1 060 ℃急冷
析出硬化処理 H900 470∼490 ℃空冷
H1025 540 ∼560 ℃空冷
H1075 570 ∼590 ℃空冷
H1150 610 ∼630 ℃空冷
SUS631 固溶化熱処理 S 1 000∼1 100 ℃急冷
析出硬化処理 RH950 955±10 ℃に 10 分間保持,室温まで空冷,24 時間以内に
−73±6 ℃に冷却し 8 時間保持,510±10 ℃に 60 分間保持後
空冷
TH1050 760 ±15 ℃に 90 分間保持,1 時間以内に 15 ℃以下に冷却し
30 分間保持,565±10 ℃に 90 分間保持後空冷
a)
注 SUS630 については,固溶化熱処理及び析出硬化処理以外の熱処理を受渡当事者間で協定されること
がある。
附属書 JB
(参考)
JIS と対応国際規格との対比表
JIS G 4305:2012 冷間圧延ステンレス鋼板及び鋼帯 ISO 16143-1:2004 Stainless steels for general purposes−Par
ISO 9445-1:2009 Continuously cold-rolled stainless steel −
dimensions and form−Part 1: Narrow strip and cut lengths
ISO 9445-2:2009 Continuously cold-rolled stainless steel −
dimensions and form−Part 2: Wide strip and plate/sheet
(I)JIS の規定 (II) (III)国際規格の規定 (IV)JIS と国際規格との技術的差異の箇条 (V)JIS と国際
国際規 ごとの評価及びその内容 異の理由及び
格番号
箇条番号 内容 箇条番号 内容 箇条ごと 技術的差異の内容
及び題名 の評価
1 適用範 冷間圧延の,ステンレ ISO 1 一般用途向け熱間圧延及 削除 JIS では,冷間圧延ステンレス JIS は,熱間
囲 ス鋼板(以下,板とい 16143-1 び冷間圧延ステンレス薄 鋼板及び鋼帯について規定。 及び鋼帯につ
う)及びステンレス鋼 板,厚板/及び鋼帯につ 規定しており
帯(以下,帯という) いて規定。 い。
について規定。
2 引用規
格
3 種類の オーステナイト系,オ ISO 4,6 ISO 規格の記号体系によ 変更 JIS と ISO 規格の記号体系が異 各国は,それ
記号 ーステナイト・フェラ 16143-1 る。 なる。 ち,それらは
イト系,フェライト オーステナイト系,オー い る 。 2003
系,マルテンサイト系 ステナイト・フェライト ISO/TS 4949
及び析出硬化系の 62 系,フェライト系,マル 記号体系に従
種類の記号及び分類 テンサイト系及び析出硬 る。
を規定。 化系の 41 種類の記号及び
分類を規定。
4 製造方 冷 間 圧 延 後 の 板 及 び 7.1 注文時に特に合意されて 削除 JIS では,冷間圧延ステンレス JIS は,熱間
法 帯の処理方法を規定。 7.2 いなければ,製鋼方法は 鋼板及び 鋼帯 の製造 方法に つ 及び鋼帯につ
製造業者の自由裁量。 いて規定。 規定しており
製造方法と表面仕上げの い。
種類を規定。
注記 1 箇条ごとの評価欄の用語の意味は,次による。
− 一致……………… 技術的差異がない。
− 削除……………… 国際規格の規定項目又は規定内容を削除している。
− 追加……………… 国際規格にない規定項目又は規定内容を追加している。
− 変更……………… 国際規格の規定内容を変更している。
注記 2 JIS と国際規格との対応の程度の全体評価欄の記号の意味は,次による。
− MOD…………… 国際規格を修正している。